INTEGRATED CIRCUITS DATA SHEET 74LVCH32373A 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state Product specification File under Integrated Circuits, IC24 1999 Nov 24 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state FEATURES 74LVCH32373A The 74LVCH32373A is a 32-bit transparent D-type latch featuring separate D-type inputs for each latch and 3-state outputs for bus oriented applications. One latch enable (nLE) input and one output enable (nOE) are provided for each octal. Inputs can be driven from either 3.3 or 5 V devices. • 5 V tolerant inputs/outputs for interfacing with 5 V logic • Wide supply voltage range from 1.2 to 3.6 V • CMOS low power consumption • MULTIBYTE flow-trough standard pin-out architecture • Low inductance multiple power and ground pins for minimum noise and ground bounce The 74LVCH32373A consists of 4 sections of eight D-type transparent latches with 3-state true outputs. When input nLE is HIGH, data at the nDn inputs enter the latches. In this condition the latches are transparent, i.e. a latch output will change each time its corresponding D-input changes. • Direct interface with TTL levels • Bus hold on data inputs • Typical output ground bounce voltage: VOLP < 0.8 V at VCC = 3.3 V and Tamb = 25 °C When input nLE is LOW the latches store the information that was present at the D-inputs one set-up time preceding the HIGH-to-LOW transition of nLE. When input nOE is LOW, the contents of the eight latches are available at the outputs. When input nOE is HIGH, the outputs go to the high-impedance OFF-state. Operation of the nOE input does not affect the state of the latches. • Typical output undershoot voltage: VOHV > 2 V at VCC = 3.3 V and Tamb = 25 °C • Power off disables outputs, permitting live insertion • Packaged in plastic fine-pitch ball grid array package. DESCRIPTION The 74LVCH32373A bus hold data input circuits eliminate the need for external pull-up resistors to hold unused inputs. The 74LVCH32373A is a high-performance, low-power, low-voltage, Si-gate CMOS device, superior to most advanced CMOS compatible TTL families. The inputs can be driven from either 3.3 or 5 V devices. In 3-state operation, outputs can handle 5 V. These features allow the use of these devices in a mixed 3.3 or 5 V environment. QUICK REFERENCE DATA GND = 0 V; Tamb = 25 °C; tr = tf ≤ 2.5 ns. SYMBOL tPHL/tPLH PARAMETER CONDITIONS UNIT propagation delay nDn to nQn CL = 50 pF; VCC = 3.3 V 3.0 ns nLE to nQn CL = 50 pF; VCC = 3.3 V 3.4 ns 5.0 pF 26 pF CI input capacitance CPD power dissipation capacitance per buffer VI = GND to VCC; note 1 Note 1. CPD is used to determine the dynamic power dissipation (PD in µW). PD = CPD × VCC2 × fi + Σ (CL × VCC2 × fo) where: fi = input frequency in MHz; fo = output frequency in MHz; CL = output load capacitance in pF; VCC = supply voltage in Volts; Σ (CL × VCC2 × fo) = sum of the outputs. 1999 Nov 24 TYPICAL 2 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A FUNCTION TABLE See note 1. INPUTS OUTPUTS nOE nLE nDn INTERNAL LATCHES Enable and read register (transparent mode) L H L L L L H H H H Latch and read register L L l L L L L h H H H L l L Z H L h H Z OPERATING MODE Latch register and disable outputs nQn Note 1. H = HIGH voltage level; h = HIGH voltage level one set-up time prior to the HIGH-to-LOW LE transition; L = LOW voltage level; l = LOW voltage level one set-up time prior to the HIGH-to-LOW LE transition; Z = high-impedance OFF-state. ORDERING INFORMATION PACKAGE TYPE NUMBER 74LVCH32373AEC TEMPERATURE RANGE PINS PACKAGE MATERIAL CODE −40 to +85 °C 96 LFBGA96 plastic SOT536-1 PINNING SYMBOL DESCRIPTION nDn data inputs nLE latch enable inputs (active HIGH) nQn data outputs GND ground (0 V) nOE output enable inputs (active LOW) VCC DC supply voltage 1999 Nov 24 3 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A MNA492 handbook, full pagewidth 6 1D1 1D3 1D5 1D7 2D1 2D3 2D5 2D7 3D1 3D3 3D5 3D7 4D1 4D3 4D5 4D6 5 1D0 1D2 1D4 1D6 2D0 2D2 2D4 2D6 3D0 3D2 3D4 3D6 4D0 4D2 4D4 4D7 4 1LE GND VCC GND GND VCC GND 2LE 3 1OE GND VCC GND GND VCC GND 2OE 3OE GND VCC GND GND VCC GND 4OE 2 1Q0 1Q2 1Q4 1Q6 2Q0 2Q2 2Q4 2Q6 3Q0 3Q2 3Q4 3Q6 4Q0 4Q2 4Q4 4Q7 1 1Q1 1Q3 1Q5 1Q7 2Q1 2Q3 2Q5 2Q7 3Q1 3Q3 3Q5 3Q7 4Q1 4Q3 4Q5 4Q6 A B C D E F G 3LE GND VCC GND GND VCC GND 4LE H J K L M N P R T Fig.1 Pin configuration. handbook, full pagewidth 1D0 D 2D0 1Q0 Q LATCH 9 LE LE LE 2LE 1OE 2OE to 7 other channels D 4D0 3Q0 Q LE 2Q0 LE to 7 other channels LATCH 17 D Q 4Q0 LATCH 25 LE LE 3LE 4LE 3OE 4OE to 7 other channels LE to 7 other channels Fig.2 Logic symbol. 1999 Nov 24 Q LATCH 1 1LE 3D0 D 4 MNA493 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state handbook, halfpage 74LVCH32373A VCC data input to internal circuit MNA473 Fig.3 Bus hold circuit. 1999 Nov 24 5 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A RECOMMENDED OPERATING CONDITIONS LIMITS SYMBOL PARAMETER CONDITIONS UNIT MIN. VCC DC supply voltage VI DC input voltage VO DC output voltage maximum speed performance low-voltage applications Tamb operating ambient temperature tr,tf (∆t/∆f) input rise and fall times 2.7 MAX. 3.6 V 1.2 3.6 V 0 5.5 V HIGH or LOW state 0 VCC V 3-state 0 5.5 V see DC and AC characteristics per device −40 +85 °C VCC = 1.2 to 2.7 V 0 20 ns/V VCC = 2.7 to 3.6 V 0 10 LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134); voltages are referenced to GND (ground = 0 V). SYMBOL PARAMETER CONDITIONS MIN. −0.5 MAX. VCC DC supply voltage VI DC input voltage note 1 −0.5 +6.5 V IIK DC input diode current VI < 0 − −50 mA IOK DC output diode current VO > VCC or VO < 0; note 1 − ±50 mA VO DC output voltage HIGH or LOW state; note 1 −0.5 VCC + 0.5 V 3-state; note 1 −0.5 +6.5 V IO DC output source or sink current VO = 0 to VCC − ±50 mA ICC,IGND DC VCC or GND current − ±100 mA Tstg storage temperature +150 °C PD power dissipation per package 1000 mW −65 temperature range −40 to +85 °C; − note 2 +6.5 UNIT Notes 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. Above 70 °C the value of PD derates linearly with 1.8 mW/K. 1999 Nov 24 6 V Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A DC CHARACTERISTICS Over recommended operating conditions; voltages are referenced to GND (ground = 0 V). Tamb −40 to +85°C TEST CONDITIONS SYMBOL PARAMETER OTHER VIH HIGH-level input voltage VIL LOW-level input voltage VCC(V) 1.2 VCC VOL HIGH-level output voltage LOW-level output voltage − − − − − − GND 2.7 to 3.6 − − 0.8 2.7 to 3.6 2.0 VOH TYP.(1) MAX. MIN. 1.2 UNIT V V VI = VIH or VIL IO = −12 mA 2.7 VCC − 0.5 − − IO = −100 µA 3.0 VCC − 0.2 VCC − IO = −18 mA 3.0 VCC − 0.6 − − IO = −24 mA 3.0 VCC − 0.8 − − IO = 12 mA 2.7 − − 0.40 IO = 100 µA 3.0 − − 0.20 IO = 24 mA 3.0 − − 0.55 V VI = VIH or VIL V II input leakage current VI = 5.5 V or GND; note 2 3.6 − ±0.1 ±5 µA IOZ 3-state output OFF-state current VI = VIH or VIL; VO = 5.5 V or GND 3.6 − 0.1 ±5 µA Ioff power off leakage supply current VI or VO = 5.5 V 0.0 − 0.1 ±10 µA − ICC quiescent supply current VI = VCC or GND; IO = 0 3.6 0.1 40 µA ∆ICC additional quiescent supply current per input pin VI = VCC − 0.6 V; IO = 0 2.7 to 3.6 − 5 500 µA IBHL bus hold LOW sustaining current VI = 0.8 V; notes 3, 4 and 5 3.0 75 − − µA IBHH bus hold HIGH sustaining current VI = 2.0 V; notes 3, 4 and 5 3.0 −75 − − µA IBHLO bus hold LOW overdrive current notes 3, 4 and 6 3.6 500 − − µA IBHHO bus hold HIGH overdrive current notes 3, 4 and 6 3.6 −500 − − µA Notes 1. All typical values are at VCC = 3.3 V and Tamb = 25 °C. 2. For bus hold parts the bus hold circuit is switched off when VI exceeds VCC allowing 5.5 V on the input terminal. 3. Valid for data inputs of bus hold parts (LVCH32-A) only. 4. For data inputs only; control inputs do not have a bus hold circuit. 5. The specified sustaining current at the data input holds the input below the specified VI level. 6. The specified overdrive current at the data input forces the data input to the opposite logic input level. 1999 Nov 24 7 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A AC CHARACTERISTICS GND = 0 V; tr = tf ≤ 2.5 ns; CL = 50 pF; RL = 500 Ω. Tamb = −40 to +85 °C TEST CONDITIONS SYMBOL PARAMETER WAVEFORMS tPHL/tPLH propagation delay nDn to nQn see Figs 4 and 8 propagation delay nLE to nQn see Figs 5 and 8 3-state output enable time nOE to nQn see Figs 7 and 8 3-state output disable time nOE to nQn see Figs 7 and 8 tW nLE pulse width HIGH tsu set-up time nDn to nLE tPZH/tPZL tPHZ/tPLZ th hold time nDn to nLE VCC (V) MIN. 2.7 1.5 − 5.7 3.0 to 3.6 1.5 3.0 4.7 2.7 1.5 − 5.8 3.0 to 3.6 1.5 3.4 4.8 2.7 1.5 − 6.5 3.0 to 3.6 1.5 3.5 5.5 2.7 1.5 − 6.4 1.5 3.9 5.4 see Figs 5 and 8 2.7 3.0 − − 3.0 to 3.6 3.0 2.0 − see Figs 6 and 8 2.7 1.7 − − 3.0 to 3.6 +1.7 −0.1 − 2.7 1.2 − − 3.0 to 3.6 1.2 0.1 − Note 1. All typical values are measured at VCC = 3.3 V and Tamb = 25 °C. AC WAVEFORMS VI VM nDn input GND t PHL t PLH VOH VM nQn output VOL MNA494 VM = 1.5 V at VCC ≥ 2.7 V; VM = 0.5 × VCC at VCC < 2.7 V; VOL and VOH are typical output voltage drop that occur with the output load. Fig.4 Input (nDn) to output (nQn) propagation delay times. 1999 Nov 24 8 UNIT MAX. 3.0 to 3.6 see Figs 6 and 8 handbook, halfpage TYP.(1) ns ns ns ns ns ns ns Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A VI handbook, full pagewidth nLE input VM VM GND tW t PHL t PLH VOH VM nQn output VOL MNA495 VM = 1.5 V at VCC ≥ 2.7 V; VM = 0.5 × VCC at VCC < 2.7 V; VOL and VOH are typical output voltage drop that occur with the output load. Fig.5 Latch enable inputs (nLE) pulse width and the latch enable input to outputs (nQn) propagation delay times. VI handbook, full pagewidth VM nDn input GND th th t su t su VI nLE input VM GND MNA496 VM = 1.5 V at VCC ≥ 2.7 V; VM = 0.5 × VCC at VCC < 2.7 V. Fig.6 Set-up and hold times for inputs (nDn) to inputs (nLE). 1999 Nov 24 9 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A VI handbook, full pagewidth nOE input VM GND t PLZ t PZL VCC output LOW-to-OFF OFF-to-LOW VM VX VOL t PZH t PHZ VOH VY output HIGH-to-OFF OFF-to-HIGH GND VM outputs enabled outputs enabled outputs disabled MNA478 VM = 1.5 V at VCC ≥ 2.7 V; VM = 0.5 × VCC at VCC < 2.7 V; VX = VOL + 0.3 V at VCC ≥ 2.7 V; VX = VOL + 0.1 V at VCC < 2.7 V; VY = VOH − 0.3 V at VCC ≥ 2.7 V; VY = VOH − 0.1 V at VCC < 2.7 V; VOL and VOH are typical output voltage drop that occur with the output load. Fig.7 3-state output enable and disable times. S1 handbook, full pagewidth VCC PULSE GENERATOR VI RL 500 Ω VO 2 × VCC open GND D.U.T. CL 50 pF RT RL 500 Ω MNA479 TEST S1 VCC Definitions for test circuit: RL = load resistor. CL = load capacitance including jig and probe capacitance. VI tPLH/tPHL open tPLZ/tPZL 2 × VCC <2.7 V VCC tPHZ/tPZH GND 2.7 to 3.6 V 2.7 V RT = termination resistance should be equal to the output impedance Zo of the pulse generator. Fig.8 Load circuitry for switching times. 1999 Nov 24 10 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A PACKAGE OUTLINE LFBGA96: plastic low profile fine-pitch ball grid array package; 96 balls; body 13.5 x 5.5 x 1.05 mm SOT536-1 D ball A1 index area A2 A E A1 detail X b A ∅w M ZD e y v A ZE T R P N M L K J H G F E D C B A e X 1 2 3 4 5 6 DIMENSIONS (mm are the original dimensions) UNIT A max. A1 A2 b D E e v w y ZD ZE mm 1.5 0.41 0.31 1.2 0.9 0.51 0.41 5.6 5.4 13.6 13.4 0.8 0.2 0.15 0.1 0.93 0.58 0.93 0.58 OUTLINE VERSION REFERENCES IEC JEDEC EIAJ 5 10 mm scale EUROPEAN PROJECTION ISSUE DATE 98-11-25 99-06-03 SOT536-1 1999 Nov 24 0 11 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A SOLDERING If wave soldering is used the following conditions must be observed for optimal results: Introduction to soldering surface mount packages • Use a double-wave soldering method comprising a turbulent wave with high upward pressure followed by a smooth laminar wave. This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 90011). • For packages with leads on two sides and a pitch (e): – larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be parallel to the transport direction of the printed-circuit board; There is no soldering method that is ideal for all surface mount IC packages. Wave soldering is not always suitable for surface mount ICs, or for printed-circuit boards with high population densities. In these situations reflow soldering is often used. – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. Reflow soldering The footprint must incorporate solder thieves at the downstream end. Reflow soldering requires solder paste (a suspension of fine solder particles, flux and binding agent) to be applied to the printed-circuit board by screen printing, stencilling or pressure-syringe dispensing before package placement. • For packages with leads on four sides, the footprint must be placed at a 45° angle to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves downstream and at the side corners. Several methods exist for reflowing; for example, infrared/convection heating in a conveyor type oven. Throughput times (preheating, soldering and cooling) vary between 100 and 200 seconds depending on heating method. During placement and before soldering, the package must be fixed with a droplet of adhesive. The adhesive can be applied by screen printing, pin transfer or syringe dispensing. The package can be soldered after the adhesive is cured. Typical reflow peak temperatures range from 215 to 250 °C. The top-surface temperature of the packages should preferable be kept below 230 °C. Typical dwell time is 4 seconds at 250 °C. A mildly-activated flux will eliminate the need for removal of corrosive residues in most applications. Wave soldering Manual soldering Conventional single wave soldering is not recommended for surface mount devices (SMDs) or printed-circuit boards with a high component density, as solder bridging and non-wetting can present major problems. Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage (24 V or less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds at up to 300 °C. To overcome these problems the double-wave soldering method was specifically developed. When using a dedicated tool, all other leads can be soldered in one operation within 2 to 5 seconds between 270 and 320 °C. 1999 Nov 24 12 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A Suitability of surface mount IC packages for wave and reflow soldering methods SOLDERING METHOD PACKAGE REFLOW(1) WAVE BGA, LFBGA, SQFP, TFBGA not suitable suitable(2) HBCC, HLQFP, HSQFP, HSOP, HTQFP, HTSSOP, SMS not PLCC(3), SO, SOJ suitable LQFP, QFP, TQFP SSOP, TSSOP, VSO suitable suitable suitable not recommended(3)(4) suitable not recommended(5) suitable Notes 1. All surface mount (SMD) packages are moisture sensitive. Depending upon the moisture content, the maximum temperature (with respect to time) and body size of the package, there is a risk that internal or external package cracks may occur due to vaporization of the moisture in them (the so called popcorn effect). For details, refer to the Drypack information in the “Data Handbook IC26; Integrated Circuit Packages; Section: Packing Methods”. 2. These packages are not suitable for wave soldering as a solder joint between the printed-circuit board and heatsink (at bottom version) can not be achieved, and as solder may stick to the heatsink (on top version). 3. If wave soldering is considered, then the package must be placed at a 45° angle to the solder wave direction. The package footprint must incorporate solder thieves downstream and at the side corners. 4. Wave soldering is only suitable for LQFP, TQFP and QFP packages with a pitch (e) equal to or larger than 0.8 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.65 mm. 5. Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm; it is definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. DEFINITIONS Data sheet status Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications. Limiting values Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. 1999 Nov 24 13 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A NOTES 1999 Nov 24 14 Philips Semiconductors Product specification 32-bit transparent D-type latch with 5 V tolerant inputs/outputs; 3-state 74LVCH32373A NOTES 1999 Nov 24 15 Philips Semiconductors – a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstraße 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SÃO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 62 5344, Fax.+381 11 63 5777 For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 Internet: http://www.semiconductors.philips.com SCA 68 © Philips Electronics N.V. 1999 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 245004/01/pp16 Date of release: 1999 Nov 24 Document order number: 9397 750 06466