DRV601 www.ti.com SLOS553 – JANUARY 2008 DIRECTPATH™ STEREO LINE DRIVER, ADJUSTABLE GAIN FEATURES 1 • External Gain Setting Resistors • Space Saving Package – 20-Pin, 4 mm × 4 mm Thin QFN, Thermally Optimized PowerPAD™ Package • Ground-Referenced Outputs Eliminate DC-Blocking Capacitor – Reduce Board Area – Reduce Component Cost – Improve THD+N Performance – No Degradation of Low-Frequency Response Due to Output Capacitors • Wide Power Supply Range: 1.8 V to 4.5 V • 2 Vrms/Ch Output Voltage into 600 Ω at 3.3 V supply • 2 • • Independent Right and Left Channel Shutdown Control Short-Circuit and Thermal Protection Pop Reduction Circuitry APPLICATIONS • • • • • Set-Top Boxes CD / DVD Players DVD-Receivers HTIB PDP / LCD TV's DESCRIPTION The DRV601 is a stereo line driver designed to allow the removal of the output dc-blocking capacitors for reduced component count and cost. The device is ideal for single supply electronics where size and cost are critical design parameters. The DRV601 is capable of driving 2 Vrms into a 600-Ω load at 3.3 V. The device has external gain setting resistors, that support a gain range of -1V/V to -10V/V, and line outputs that has ±8-kV IEC ESD protection. The device has independent shutdown control for the right and left audio channels. The DRV601 is available in a 4 mm × 4 mm Thin QFN package. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. DIRECTPATH, PowerPAD, DirectPath are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008, Texas Instruments Incorporated DRV601 www.ti.com SLOS553 – JANUARY 2008 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. NC PVDD SDL SGND NC 20 19 18 17 16 RTJ (QFN) PACKAGE (TOP VIEW) 13 INL NC 4 12 NC PVSS 5 11 OUTR 10 3 SVDD C1N 9 SDR OUTL 14 8 2 NC PGND 7 INR SVSS 15 6 1 NC C1P NC − No internal connection TERMINAL FUNCTIONS TERMINAL NAME QFN C1P 1 PGND 2 C1N 3 NC 4, 6, 8, 12, 16, 20 I/O DESCRIPTION I/O Charge pump flying capacitor positive terminal I Power ground, connect to ground. I/O Charge pump flying capacitor negative terminal No connection PVSS 5 O Output from charge pump. SVSS 7 I Amplifier negative supply, connect to PVSS via star connection. OUTL 9 O Left audio channel output signal SVDD 10 I Amplifier positive supply, connect to PVDD via star connection. OUTR 11 O Right audio channel output signal INL 13 I Left audio channel input signal SDR 14 I Right channel shutdown, active low logic. INR 15 I Right audio channel input signal SGND 17 I Signal ground, connect to ground. SDL 18 I Left channel shutdown, active low logic. PVDD 19 I Supply voltage, connect to positive supply. Exposed Pad Exposed pad must be soldered to a floating plane. Do NOT connect to power or ground. 2 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range, TA = 25°C (unless otherwise noted) VALUE / UNIT Supply voltage, AVDD, PVDD –0.3 V to 5.5 V VI Input voltage R(Load) Minimum load impedance TA Operating free-air temperature range 0°C to 70°C TJ Operating junction temperature range 0°C to 150°C Tstg Storage temperature range –65°C to 85°C (1) VSS – 0.3 V to VDD + 0.3 V ≥ 100 Ω Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. AVAILABLE OPTIONS (1) (2) TA PACKAGED DEVICES (1) PART NUMBER SYMBOL –40°C to 85°C 20-pin, 4 mm × 4 mm QFN DRV601RTJ (2) AKQ For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. The RTJ package is only available taped and reeled. To order, add the suffix “R” to the end of the part number for a reel of 3000, or add the suffix “T” to the end of the part number for a reel of 250 (e.g., DRV601RTJR). RECOMMENDED OPERATING CONDITIONS VSS Supply voltage, AVDD, PVDD VIH High-level input voltage SDL, SDR VIL Low-level input voltage SDL, SDR TA Operating free-air temperature (1) MIN MAX UNIT 1.8 4.5 (1) V 1.5 V 0 0.5 V 70 °C MAX UNIT Device can shut down for VDD > 4.5 V to prevent damage to the device. ELECTRICAL CHARACTERISTICS TA = 25°C (unless otherwise noted) PARAMETER TEST CONDITIONS |VOS| Output offset voltage VDD = 1.8 V to 4.5 V, Inputs grounded PSRR Power Supply Rejection Ratio VDD = 1.8 V to 4.5 V VOH High-level output voltage VDD = 3.3 V, RL = 600 Ω VOL Low-level output voltage VDD = 3.3 V, RL = 600 Ω |IIH| High-level input current (SDL, SDR) VDD = 4.5 V, VI = VDD |IIL| Low-level input current (SDL, SDR) VDD = 4.5 V, VI = 0 V IDD Supply Current MIN TYP 8 88 dB 3.10 V VDD = 1.8 V, No load, SDL= SDR = VDD 5.3 VDD = 3.3 V, No load, SDL = SDR = VDD 7.1 VDD = 4.5 V, No load, SDL = SDR = VDD 8.7 Shutdown mode, VDD = 1.8 V to 4.5 V mV –3.05 V 1 µA 1 µA mA 1 µA 3 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 OPERATING CHARACTERISTICS VDD = 3.3 V , TA = 25°C, RL = 600 Ω, C(PUMP) = C(PVSS) = 1 µF , CIN = 1 µF, Rin = 10 kΩ, Rfb = 20 kΩ (unless otherwise noted) PARAMETER VO THD+N Output Voltage(Outputs In Phase) Total harmonic distortion plus noise Crosstalk Avo Open-loop voltage gain Rin Input resistor range Rfb Feedback resistor range TEST CONDITIONS MIN TYP THD = 1%, VDD = 3.3 V, f = 1 kHz 2.1 THD = 1%, VDD = 4.5 V, f = 1 kHz 2.7 THD = 1%, VDD = 4.5 V, f = 1 kHz, RL = 100 kΩ 2.8 VO = 2 Vrms, f = 1 kHz 0.008% VO = 2 Vrms, f = 6.67 kHz 0.030% VO = 2 Vrms, f = 1 kHz MAX VRMS -80 dB 155 1 4.7 UNIT dB 10 47 20 100 kΩ kΩ Slew rate 2.2 V/µs Maximum capacitive load 300 pF µVrms Vn Noise output voltage 22-kHz filter, A-weighted 10 ESD Electrostatic discharge OUTR, OUTL ±8 fosc Charge pump switching frequency 280 Start-up time from shutdown Signal-to-noise ratio G(bw) Unity Gain Bandwidth Thermal shutdown kV 420 450 Input impedance SNR 320 µs 1 Vo = 2 Vrms (THD+N = 0.1%), 22-kHz BW, A-weighted MΩ 105 dB 3.5 Threshold Hysteresis 4 kHz 150 MHz 170 15 °C °C Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 Functional Block Diagram Functional Block Diagram Rfb SVDD + Rin SVSS SGND SVDD Audio Out - R Short Circuit Protection Audio Out - L + Rin Rfb SVSS C 1P SDx Charge Pump Bias Circuitry C 1N PVSS 5 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 TYPICAL CHARACTERISTICS C(PUMP) = C(PVSS) = 1 µF , CIN = 1 µF, Rin = 10 kΩ, Rfb = 20 kΩ (unless otherwise noted) Table of Graphs FIGURE Total harmonic distortion + noise vs Output Voltage 1-6 Total harmonic distortion + noise vs Frequency 7-8 Quiescent supply current vs Supply voltage 9 Output spectrum 10 Gain and phase vs Frequency RL = 100 kW, f = 1 kHz 1 0.1 0.01 0.001 3m 10m 100m 500m VO - Output Voltage - Vrms 2 3 10 VDD = 3.3 V, RL = 100 kW, f = 1 kHz 1 0.1 0.01 0.001 3m 10m 100m 500m VO - Output Voltage - Vrms 2 3 TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT VOLTAGE THD + N - total Harmonic Distortion + Noise - % VDD = 1.8 V, THD + N - total Harmonic Distortion + Noise - % 10 TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT VOLTAGE 10 VDD = 4.5 V, RL = 100 kW, f = 1 kHz 1 0.1 0.01 0.001 3m 10m 100m 500m VO - Output Voltage - Vrms 2 3 Figure 2. Figure 3. TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT VOLTAGE TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT VOLTAGE TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT VOLTAGE 10 VDD = 1.8 V, RL = 600 W, f = 1 kHz 1 0.1 0.01 0.001 3m 10m 100m 500m VO - Output Voltage - Vrms Figure 4. 2 3 10 VDD = 3.3 V, RL = 600 W, f = 1 kHz 1 0.1 0.01 0.001 3m 10m 100m 500m VO - Output Voltage - Vrms Figure 5. 6 2 3 THD + N - total Harmonic Distortion + Noise - % Figure 1. THD + N - total Harmonic Distortion + Noise - % THD + N - total Harmonic Distortion + Noise - % THD + N - total Harmonic Distortion + Noise - % TOTAL HARMONIC DISTORTION + NOISE vs OUTPUT VOLTAGE 11-12 10 VDD = 4.5 V, RL = 600 W, f = 1 kHz 1 0.1 0.01 0.001 3m 10m 100m 500m VO - Output Voltage - Vrms 2 3 Figure 6. Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 VDD = 3.3 V, RL = 600 W, 200 mVrms 1 0.1 0.01 0.001 20 50 100 500 1k 2k f - frequency - Hz 5k 20k 10 10 RL = 600 W, No Load VDD = 3.3 V, RL = 600 W, 2 Vrms 1 0.1 0.01 0.001 20 6 4 2 0 50 100 500 1k 2k f - frequency - Hz 0 5k 20k 0.5 1 1.5 2 2.5 3 3.5 VDD - Supply Voltage - V Figure 8. Figure 9. FFT vs FREQUENCY GAIN vs FREQUENCY PHASE vs FREQUENCY 7 6.5 Gain - dB -40 -60 -80 VDD = 3.3 V, RL = 600 W, 2 Vrms -25 6 -50 5.5 -75 Phase - deg RL = 600 W, G = -60dB 5 4.5 -100 4.5 0 VDD = 3.3 V, VDD = 3.3 V, -20 8 Figure 7. 0 FFT - dBr QUIESCENT SUPPLY CURRENT vs SUPPLY VOLTAGE IDD - Supply Current - mA 10 TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY THD + N - total Harmonic Distortion + Noise - % THD + N - total Harmonic Distortion + Noise - % TOTAL HARMONIC DISTORTION + NOISE vs FREQUENCY RL = 600 W, 2 Vrms -100 -125 4 -150 3.5 -175 -120 -140 0 10k f - frequency - Hz 20k Figure 10. 3 20 100 1k 2k 10k f - frequency - Hz Figure 11. 100k -200 20 100 1k 2k 10k f - frequency - Hz 100k Figure 12. 7 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 APPLICATION INFORMATION Line Driver Amplifiers Single-supply Line Driver amplifiers typically require dc-blocking capacitors. The top drawing in Figure 13 illustrates the conventional Line Driver amplifier connection to the load and output signal. DC blocking capacitors are often large in value. The line load (typical resistive values of 600 Ω to 10 kΩ) combine with the dc blocking capacitors to form a high-pass filter. Equation 1 shows the relationship between the load impedance (RL), the capacitor (CO), and the cutoff frequency (fC). 1 fc = 2pRLCO (1) CO can be determined using Equation 2, where the load impedance and the cutoff frequency are known. 1 CO = 2pRLfc (2) If fC is low, the capacitor must then have a large value because the load resistance is small. Large capacitance values require large package sizes. Large package sizes consume PCB area, stand high above the PCB, increase cost of assembly, and can reduce the fidelity of the audio output signal. Conventional VDD CO VOUT CO VDD/2 GND DirectPath VDD GND VSS Figure 13. Amplifier Applications The DirectPath™ amplifier architecture operates from a single supply but makes use of an internal charge pump to provide a negative voltage rail. Combining the user provided positive rail and the negative rail generated by the IC, the device operates in what is effectively a split supply mode. The output voltages are now centered at zero volts with the capability to swing to the positive rail or negative rail. The DirectPath™ amplifier requires no output dc blocking capacitors. The bottom block diagram and waveform of Figure 13 illustrate the ground-referenced Line Driver architecture. This is the architecture of the DRV601. 8 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 Charge Pump Flying Capacitor and PVSS Capacitor The charge pump flying capacitor serves to transfer charge during the generation of the negative supply voltage. The PVSS capacitor must be at least equal to the charge pump capacitor in order to allow maximum charge transfer. Low ESR capacitors are an ideal selection, and a value of 1µF is typical. Capacitor values that are smaller than 1µF can be used, but the maximum output voltage may be reduced and the device may not operate to specifications. Decoupling Capacitors The DRV601 is a DirectPath™ Line Driver amplifier that require adequate power supply decoupling to ensure that the noise and total harmonic distortion (THD) are low. A good low equivalent-series-resistance (ESR) ceramic capacitor, typically 2.2µF, placed as close as possible to the device VDD lead works best. Placing this decoupling capacitor close to the DRV601 is important for the performance of the amplifier. For filtering lower frequency noise signals, a 10-µF or greater capacitor placed near the audio power amplifier would also help, but it is not required in most applications because of the high PSRR of this device. Gain setting resistors ranges The gain setting resistors, Rin and Rfb, must be chosen so that noise, stability and input capacitor size of the DRV601 is kept within acceptable limits. Voltage gain is defined as Rfb divided by Rin. Selecting values that are too low demands a large input ac-coupling capacitor, CIN . Selecting values that are too high increases the noise of the amplifier. Table 1 lists the recommended resistor values for different gain settings. Table 1. Recommended Resistor Values Gain Input Resistor Value, Rin Feedback Resistor Value, Rfb -1 V/V 10 kΩ 10 kΩ -1.5 V/V 10 kΩ 15 kΩ -2 V/V 10 kΩ 20 kΩ -10 V/V 4,7 kΩ 47 kΩ Input-Blocking Capacitors DC input-blocking capacitors are required to be added in series with the audio signal into the input pins of the DRV601. These capacitors block the DC portion of the audio source and allow the DRV601 inputs to be properly biased to provide maximum performance. These capacitors form a high-pass filter with the input resistor, Rin. The cutoff frequency is calculated using Equation 3. For this calculation, the capacitance used is the input-blocking capacitor and the resistance is the input resistor chosen from the gain table above, then the frequency and/or capacitance can be determined when one of the two values are given. 1 1 fc IN + or C IN + 2p fc R 2p RIN C IN IN IN (3) Supply Voltage Limiting At 4.5 V The DRV601 have a built-in charge pump which serves to generate a negative rail for the line driver. Because the line driver operates from a positive voltage and negative voltage supply, circuitry has been implemented to protect the devices in the amplifier from an overvoltage condition. Once the supply is above 4.5 V, the DRV601 can shut down in an overvoltage protection mode to prevent damage to the device. The DRV601 resume normal operation once the supply is reduced to 4.5 V or lower. Capacitive load The DRV601 has the ability to drive a high capacitive load up to 330pF directly, higher capacitive loads can be accepted by adding a series resistor of 10Ω or larger. The figure below shows a 10kHz signal into a 470pF capacitor using the 10R series resistor. 9 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 Ch2 1 V/div SQUARE WAVE OUTPUT VOLTAGE with CAPACITIVE LOAD t − Time = 20 ms/div Figure 14. Layout Recommendations A proposed layout for the DRV601 can be seen in the DRV601EVM user's guide, SLOU215, and the Gerber files can be downloaded on www.ti.com, open the DRV601 product folder and look in the Tools & Software folder. Exposed Pad On DRV601RTJ Package The exposed metal pad on the DRV601RTJ package must be soldered down to a pad on the PCB in order to maintain reliability. The pad on the PCB should be allowed to float and not be connected to ground or power. Connecting this pad to power or ground prevents the device from working properly because it is connected internally to PVSS. SGND and PGND Connections The SGND and PGND pins of the DRV601 must be routed back to the decoupling capacitor separately in order to provide proper device operation. If the SGND and PGND pins are connected directly to each other, the part functions without risk of failure, but the noise and THD performance do not meet the specifications. Gain setting resistors The gain setting resistors, Rin and Rfb , must be placed close to pin 13 respectively pin 17 to minimize the capacitive loading on these input pins and to ensure maximum stability of the DRV601. For the recommenced PCB layout, see the DRV601EVM user guide. 10 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 DRV601 www.ti.com SLOS553 – JANUARY 2008 33 kW 1 mF VOUT_R 33 pF 15 kW Audio In - R Audio Out - R 47 kW 330 pF PCM1773 Right Output DRV601 33 kW 1 mF 15 kW 33 pF VCC Audio Out - L Audio In - L VOUT_L 330 pF Left Output 47 kW PGND SGND C1P Shuntdown Control SDL SDR C1N PVDD SVDD PVSS 3.3 V 1 mF 1 mF 1 mF Figure 15. Application Circuit 11 Copyright © 2008, Texas Instruments Incorporated Product Folder Link(s): DRV601 PACKAGE OPTION ADDENDUM www.ti.com 28-Mar-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty DRV601RTJR ACTIVE QFN RTJ 20 3000 Green (RoHS & no Sb/Br) Cu NiPdAu Level-2-260C-1 YEAR DRV601RTJRG4 ACTIVE QFN RTJ 20 3000 Green (RoHS & no Sb/Br) Cu NiPdAu Level-2-260C-1 YEAR DRV601RTJT ACTIVE QFN RTJ 20 250 Green (RoHS & no Sb/Br) Cu NiPdAu Level-2-260C-1 YEAR DRV601RTJTG4 ACTIVE QFN RTJ 20 250 Green (RoHS & no Sb/Br) Cu NiPdAu Level-2-260C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device DRV601RTJT Package Package Pins Type Drawing QFN RTJ 20 SPQ 250 Reel Reel Diameter Width (mm) W1 (mm) 180.0 12.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) 4.3 4.3 1.5 8.0 W Pin1 (mm) Quadrant 12.0 Q2 PACKAGE MATERIALS INFORMATION www.ti.com 11-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DRV601RTJT QFN RTJ 20 250 190.5 212.7 31.8 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2008, Texas Instruments Incorporated