Embedded Power for Business-Critical Continuity Rev. 11.9.09_44 DS2900 1 of 4 DS2900 2900 Watts Distributed Power System Distributed Power Bulk Front-End Total Output Power: 2900 Watts +3.3 Vdc Stand-by Output Wide Range Input Voltage: 180 - 264 Vac Electrical Specifications Special Features Input •Active power factor correction •EN61000-3-2 harmonic compliance •Active AC inrush control •2U X 3U form factor •24.8 W / in3 •+12 Vdc Output •+3.3 Vdc stand-by (5 V standby - consult factory) •No minimum load required •Hot plug operation •N + 1 redundant •Internal OR’ing fets •Active current sharing (10 - 100% load) •Built-in cooling fan (40 mm x 28 mm) •I2C communication interface bus •PMBus compliant •EERPOM for FRU data •Red/green bi-color LED status •Internal fan speed control •Fan Fail Tach Output Signal •INTEL, SSI Std. logic timing •INTEL, SSI Std. FRU data format PSM/V2.12 •Full digital control •Two year warranty •Compatible with Emerson Universal PMBus GUI Input range: 180 - 264 (2900 W) Frequency: Inrush current: 47-63 Hz, single phase AC 50 Apk maximum inrush current Efficiency: Conducted EMI: Radiated EMI: > 91% typical at nom line 50% load FCC Subpart J EN55022 Class A FCC Subpart J EN55022 Class A Meets intent of NEBS, Bel Core GR-1089 0.99 typical 1.40 mA @ 240 VAC 12 ms minimum Safety •UL/cUL 60950 (UL Recognized) •NEMKO+ CB Report EN60950 •EN60950 •CE Mark •China CCC Power factor: Leakage current: Hold up time: Output Main DC voltage: Stand-By: Adjustment range: Regulation: Over current: Over voltage: Under voltage: Turn-on delay: Main output rise time: +12 V @ 240 A (high line) +3.3 Vsb @ 3 A ± 10% on +12V only using I2C +12 Vdc; +4% / -4% +3.3 Vsb; +5% / -5% Constant current type for both the 12 VDC and 3.3V standby. See Figure 1 below +12 Vdc; 13.2 - 15.6 Vdc (110 - 130%) +3.3 Vsb; 3.63 V - 4.29 (110 - 130%) +12 Vdc; 9 - 10.8 V (latch off) 2 second max, 5 - 200 mS, monotonic rise 5 - 300 mS, monotonic rise Iout limit Vout Vout nominal Iout (+12VDC) 120% (3.3VSB) 115% Figure 1 130% 140% Embedded Power for Business-Critical Continuity Rev. 11.9.09_44 DS2900 2 of 4 Logic Control Remote ON/OFF (PSON#) The PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the +12VDC power rail. When this signal is not pulled low by the system, or left open, the +12VDC output turns off. The 3.30Vsb output remains on. This signal is pulled to a stanby voltage by a pull-up resistor internal to the power supply. The power supply fan(s) shall operate at the lowest speed Signal Type PSON# = Low PSON# = Open Accepts an open collector/drain input from the system. Pulled-up to the 3.30Vsb located in the power supply ON OFF MIN MAX Logic level low (power supply ON) 0V 0.8 V Logic level high (power supply OFF) 2.0 V 4.125 V Source Current, Vpson = low 4 mA Power up delay: Tpson on delay 5 msec 400 msec Table 1 PSON# Signal Characteristics Power Good (PWOK#) PWOK# is a power good signal and will be pulled LOW by the power supply to indicate that both the outputs are above the regulation limits of the power supply. When an output voltage falls below regulation limits or when AC power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed, PWOK will be de-asserted to a HIGH state. The start of the PWOK# delay time shall be inhibited as long as the +12VDC output is in current limit or the 3.30VSB output is below the regulation limit. Signal Type: Open collector/drain output from power supply. Pull-up to 3.30Vsb external to the power supply PWOK = High Power not good PWOK = Low Power Good MIN 0V 2.0 V Logic level low voltage, Isink = 4 mA Logic level high voltage, Isource = 200 A MAX 0.8 V 4.125 V Sink current, PWOK = low 4 mA Source current, PWOK = high 2 mA PWOK delay: Tpwok on 100 ms PWOK rise and fall time 1000 ms 100 sec Power down delay: Tpwok off 1 ms 1000 msec Table 2 PWOK# Signal Characteristics Power Supply Present Indicator (PRESENT#) The PRESENT# signal is primarily used to provide a mechanism by which the host system can sense the number of power supplies physically present (operational or not). This pin is connected to ground in the power supply. AC Input Present Indicator (ACOK#) The AC OK# signal is used to indicate presence of AC input to the power supply. This signal shall be connected to 3.3 Vsb through a resistor on the host system side. A logic “Low” level on this signal shall indicate AC input to the power supply is present. A Logic “HIgh” on this signal shall indiciate a loss of AC input to the power supply. Signal Type PRESENT# = Low PRESENT# = High Pull-up to 3.30Vsb through a resitor in the host system Present Not Present Table 3 ACOK# Signal Characteristics Embedded Power for Business-Critical Continuity Rev. 11.9.09_44 DS2900 3 of 4 Environmental Specifications Operating temperature: Storage temperature: 0° to 50 °C -40 °C to +85 °C Altitude, operating: 10,000 ft Electromagnetic susceptibility / Input transients: RoHS & lead-free compliant: Humidity: Shock and vibration specificatons: -EN61000-3-2, -3-3 -EN61000-4-2, 4-3, 4-4, -4-5, 4-11 -EN55024:1998 No tantalum caps. 20 to 90% RH, non-condensing Complies with Astec Std. Specifications, Q3205 MTBF (Calculated): 300K Hrs Belcore 332, issue b @ 25 °C and 40 °C full load MTBF (Demonstrated): > 500k Hrs Ordering Information Model Number DS2900-3 DS2900-3-002 DS2900-3-003 DS2900-3-004 Nominal Output Voltage Set Point 12.0 Vdc 12.0 Vdc 12.0 Vdc 12.0 Vdc Set Point Tolerance ± 0.2% ± 0.2% ± 0.2% ± 0.2% Total Regulation ± 4% ± 4% ± 4% ± 4% Minimum Current 0A 0A 0A 0A Maximum Current 240 A 240 A 240 A 240 A Output Ripple P/P 120 mV 120 mV 120 mV 120 mV Over Current Stand-by Air Flow 288 A - 312 A* 288 A - 312 A* 288 A - 312 A* 288 A - 312 A* 3.3 V @ 3 A 5.0 V @ 2 A 5.0 V @ 2 A 3.3 V @ 3 A Std Std Reversed Reversed *Over current latches off if overcurrent lasts over 1 seconds, otherwise it is auto recovery. AIRFLOW DIRECTION 208 HANDLE 138.4 EMI CLIP 17.5 217 ± 0.75 138.4 13.2 52 16.8 1.9 2 (2X) 14.5 96.6 77 106 ± 0.75 4.7 4 ± 0.5 1.9 (TYP) EMI CLIP 26.4 ± 0.5 78 ± 0.75 EMI CLIP 19.17 ± 0.5 Mechanical Drawing EMI CLIP Condition Stand-by - ON; Main output - OFF; AC PRESENT Stand-by - ON; Main output - ON; LED Status Blinking green Solid green Main output OCP, UVP, OVP Blinking Amber FAN_FAULT; OTP; Stand-by OCP/UVP Amber LED FAN 60X60X38 FAN GRILLE Embedded Power for Business-Critical Continuity Americas Output Connection 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone:+1 760 930 4600 Facsimile: +1 760 930 0698 DC Output Connector FCI HCI Series Plug (10 Blades, 24 Signal pins). Power Supply; FCI P/N; SK10065864-003LF FCI HCI Series Receptacle (10 Blades, 24 Signal pins). Mating; FCI P/N; SK10065866-003LF P1 - System Internal to power supply FCI HCI Series Connector 10 Power Blased 24 Signal pins P/N SK10065864-003LF DCI HCI Series Connector Molex Power Dock Senior 10 Power Blades 24 Signal pins P/N SK10065866-003LF Pin Signal Name Amps per pin1 PB-A1 PB-A2 PB-A3 PB-A4 PB-A5 PB-A6 PB-A7 PB-A8 PB-A9 PB-A10 A1 A2 A3 A4 A5 A6 B1 B2 B3 B4 B5 B6 C1 C2 C3 C4 C5 C6 D1 D2 D3 D4 D5 D6 + Vout Return + Vout Return + Vout Return + Vout Return + Vout Return + Vout + Vout + Vout + Vout + Vout +3V3SB Return +3V3SB S_INT +Vout_Share PS_ON PS_SEATED +3V3SB Return +3V3SB A2 PWR_GOOD ACOK PS_KILL +3V3SB Return +3V3SB A0 A1 SCL SDA +3V3SB Return +3V3SB +Vout_RS_RETURN _Vout_RS Reserve Reserve 100 100 100 100 100 100 100 100 100 100 1.5 1.5 N/A N/A N/A N/A 1.5 1.5 N/A N/A N/A N/A 1.5 1.5 N/A N/A N/A N/A 1.5 1.5 N/A N/A N/A N/A Input Connection 9 4 .0 % FCI P/N 51939-081LF Tyco P/N 6600100-2 9 2 .0 % Mating Connector 9 0 .0 % Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone:+44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone:+852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.PowerConversion.com techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Computing E fficie n cy Embedded Power Monitoring Outside Plant Power Switching & Controls Efficiency FCI P/N TBD Tyco P/N TBD Rev. 11.9.09_44 DS2900 4 of 4 8 8 .0 % Precision Cooling Racks & Integrated Cabinets 8 6 .0 % Services 8 4 .0 % Surge Protection 8 2 .0 % EmersonNetworkPower.com 8 0 .0 % 0 500 1000 1500 2000 Output Power 2500 3000 3500 Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2009 Emerson Electric Co.