-100mA / -50V Digital transistors (with built-in resistors) DTA124GKA Applications Inverter, Interface, Driver Dimensions (Unit : mm) DTA124GKA 1.1 2.9 0.4 Features 1)The built-in bias resistors consist of thin-film resistors with complete isolation to allow positive biasing of the input, and parasitic effects are almost completely eliminated. 2)Only the on / off conditions need to be set for operation, making the device design easy. 3)Higher mounting densities can be achieved. 0.8 1.6 2.8 (3) (2) 0.15 ROHM : SMT3 EIAJ : SC-59 1.9 0.3Min. (1) 0.95 0.95 (1) GND (2) IN (3) OUT Abbreviated symbol : K15 Structure PNP epitaxial planar silicon transistor (Resistor built-in type) Packaging specifications Part No. Inner circuit Package SMT3 Packaging type Taping Code T146 Basic ordering unit (pieces) 3000 DTA124GKA C B − R E Absolute maximum ratings (Ta=25C) Symbol Limits Unit Collector-base voltage VCBO −50 V Collector-emitter voltage VCEO −50 V Emitter-base voltage Parameter VEBO −5 V Collector current IC −100 V Collector power dissipation PC 200 mA Junction temperature Tj 150 °C Storage temperature Tstg −55 to +150 °C www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ E : Emitter C : Collector B : Base R=22kΩ 1/2 2009.06 - Rev.C DTA124GKA Data Sheet Electrical characteristics (Ta=25C) Parameter Symbol Min. Typ. Max. Unit Collector-base breakdown voltage BVCBO −50 − − V IC=−50μA Collector-emitter breakdown voltage BVCEO −50 − − V IC=−1mA Emitter-base breakdown voltage BVEBO −5 − − V IE=−330μA ICBO − − −0.5 μA VCB=−50V VEB=−4V Collector cutoff current Conditions IEBO −140 − −260 μA VCE(sat) − − −0.3 V IC=−10mA, IB=−0.5mA DC current transfer ratio hFE 56 − − − IC=−5mA, VCE=−5V Emitter-base resistance R 15.4 22 28.6 kΩ Transition frequency fT ∗ − 250 − MHz Emitter cutoff current Collector-emitter saturation voltage − VCE=−10V, IE=5mA, f=100MHz ∗Characteristics of built-in transistor. 1k VCE=5V Ta=100°C 500 DC CURRENT GAIN : hFE Ta=25°C 200 100 Ta= 40°C 50 20 10 5 2 1 100∝ 200∝ 500∝ 1m 2m 5m 10m 20m 50m 100m COLLECTOR CURRENT : IC (A) Fig.1 DC current gain vs. Collector current www.rohm.com c 2009 ROHM Co., Ltd. All rights reserved. ○ COLLECTOR SATURATION VOLTAGE : VCE(sat) (V) Electrical characteristic curves 1 IC/IB=20/1 500m Ta=100°C Ta=25°C 200m 100m Ta= 40°C 50m 20m 10m 5m 2m 1m 100∝ 200∝ 500∝ 1m 2m 5m 10m 20m 50m 100m COLLECTOR CURRENT : IC (A) Fig.2 Collector-Emitter saturation voltage vs. Collector current 2/2 2009.06 - Rev.C Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2009 ROHM Co., Ltd. All rights reserved. R0039A