HDMI05-CL02F3 5-line IPAD™, HDMI™ control line ESD protection Features ■ Low line capacitance: 12 pF max. ■ High efficiency in ESD protection ■ Lead-free package ■ Very thin package ■ High reliability offered by monolithic integration ■ High reduction of parasitic elements through integration and wafer level packaging Flip Chip 9 bumps Figure 1. Pin configuration (bump side) Complies with the standards: ■ ■ IEC 61000-4-2 Level 4 – ± 15 kV (air discharge) – ± 8 kV (contact discharge) IEC 61000-4-2 Level 1 – ± 2 kV (air discharge) – ± 2 kV (contact discharge) 3 2 1 SCL CEC 5V A SDA GND RPU2 B HPD GND RPU C Application Where ESD protection for HDMI control lines (CEC, HPD, SCL and SDA) is required: ■ Mobile phones and communication systems ■ Portable multimedia players ■ Camcorder, digital still cameras Figure 2. A1 5V The ESD protection circuitry prevents damage to the protected device when subjected to ESD surges up to 15 kV. B2 and C2 are ground pins C1 R4 R2 The HDMI05-CL02F3 chip is a low capacitance ESD protection for HDMI control pins. It also integrates pull-up resistor for I²C bus and pulldown resistor for hot plug detect and pull-up resistor for CEC line. R1 CEC SCL SDA HPD R3 A2 A3 B3 C3 Description April 2010 Schematic B1 TM: IPAD is a trademark of STMicroelectronics. HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC. Doc ID 15516 Rev 2 1/9 www.st.com 9 Characteristics 1 HDMI05-CL02F3 Characteristics Table 1. Absolute maximum ratings (Tamb = 25 °C) Symbol VPP Parameter External pins (A1, A2, A3, B3 and C3): ESD IEC 61000-4-2, level 4 - air discharge ESD IEC 61000-4-2, level 4 - contact discharge Internal pins (B1, C1): ESD IEC 61000-4-2, level 1 - air discharge ESD IEC 61000-4-2, level 1 - contact discharge Pd Line resistance power dissipation at 70 °C Top Tstg Figure 3. Value 15 8 Unit kV 2 2 60 mW Operating temperature range -30 to + 85 °C Storage temperature range -55 to + 150 °C Electrical characteristics (definitions) I Symbol VBR IRM VRM VCL Rd IPP IR αT VF Cline RI/O Table 2. = = = = = = = = = = = Parameter Breakdown voltage Leakage current @ VRM Stand-off voltage Clamping voltage Dynamic impedance Peak pulse current Breakdown current Voltage temperature coefficient Forward voltage drop Line capacitance Series resistance between Input IF VF VCL VBR VRM V IRM IR Slope = 1/Rd IPP Electrical characteristics (Tamb = 25 °C) Symbol Test condition VBR IR = 1 mA IRM VRM = 3 V per line Min. Typ. Unit 20 V 50 200 nA 6 R1, R2 1575 1750 1925 Ω R3 80 100 120 kΩ R4 22 27 32 kΩ 14 24 17 29 pF 10 12 pF Cline Vline = 0 V, Vosc = 30 mV, F = 1 MHz CEC to GND with RPU2 not connected SCL and SDA to GND with RPU not connected (measured under zero light conditions) Cline(1) Vline = 0 V, Vosc = 30 mV, F = 1 MHz CEC, SCL and SDA to GND with RPU and RPU2 grounded (measured under zero light conditions) 1. This is the line capacitance seen by the data signals in the application conditions 2/9 Max. Doc ID 15516 Rev 2 HDMI05-CL02F3 Figure 4. 0.00 Characteristics S21(dB) versus frequency Figure 5. dB - 5.00 0.00 CEC SDA 5V SCL HPD Analog crosstalk measurements dB - 40.00 - 10.00 - 80.00 - 15.00 - 120.00 CEC - RPU2 SDA - SCL SCL - RPU HPD - SCL SCL - CEC F(Hz) F(Hz) - 20.00 300.0k Figure 6. 1.0M 3.0M 10.0M 30.0M 100.0M 300.0M 1.0G 3.0G ESD response to IEC 61000-4-2 (+8 kV contact discharge) on CEC line 10 V/div 72 V 1 - 160.00 300.0k Figure 7. 1.0M 3.0M 10.0M 30.0M 100.0M 300.0M 1.0G 3.0G ESD response to IEC 61000-4-2 (-8 kV contact discharge) on CEC line 10 V/div 52 V 2 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns 39 V 3 -11 V 3 -17 V 2 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns -52 V 1 20 ns/div 20 ns/div Figure 8. ESD response to IEC 61000-4-2 (+8 kV contact discharge) on SCL line 10 V/div Figure 9. ESD response to IEC 61000-4-2 (-8 kV contact discharge) on SCL line 10 V/div 70 V 1 48 V 2 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns 39 V 3 -11 V 3 -17 V 2 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns -51 V 1 20 ns/div Doc ID 15516 Rev 2 20 ns/div 3/9 Characteristics HDMI05-CL02F3 Figure 10. ESD response to IEC 61000-4-2 (+8 kV contact discharge) on SDA line 10 V/div 79 V 1 Figure 11. ESD response to IEC 61000-4-2 (-8 kV contact discharge) on SDA line 10 V/div 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns 51 V 2 39 V 3 -14 V 3 -22 V 20 ns/div Figure 12. ESD response to IEC 61000-4-2 (+8 kV contact discharge) on HPD line 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns 20 ns/div -57 V 1 Figure 13. ESD response to IEC 61000-4-2 (-8 kV contact discharge) on HPD line 10 V/div 10 V/div 65 V 1 2 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns 49 V 2 40 V 3 -11 V 3 -17 V 2 -43 V 1 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns 20 ns/div 20 ns/div Figure 14. ESD response to IEC 61000-4-2 (+8 kV contact discharge) on 5 V line 10 V/div 10 V/div 72 V 1 Figure 15. ESD response to IEC 61000-4-2 (-8 kV contact discharge) on 5 V line 52 V 2 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns 39 V 3 -14 V 3 -20 V 2 20 ns/div 4/9 -52 V 1 Doc ID 15516 Rev 2 1 VPP: ESD peak voltage 2 VCL @ 30 ns: clamping voltage @ 30 ns 3 VCL @ 60 ns: clamping voltage @ 60 ns 20 ns/div HDMI05-CL02F3 2 Typical application schematic Typical application schematic Figure 16. Implementation with HDMI HDMI Gnd Host (Mobile Phone) Phone) (Mobile TX2TX2+ Gnd TX1TX1+ TX1TX1+ Gnd HDMIULC6 -4F3 TX0TX0- TX0TX0- TX0+ Multimedia audio controller Ctrl / status Display (TV, (TV,flat flatpanel, panel, monitor, projector) Gnd Gnd video Gnd TX2TX2+ video TX0+ Gnd Gnd TC-TC TC-TC TC+ TC+ Ctrl / status HDMI05 CL02F3 Gnd CEC audio Multimedia controller Gnd CEC SCL SCL SDA SDA V VDD DD_5V VDD_5V HPD HPD Type CCC Connector Type connector Type Connector -out Pin - out Pin-out B2 E2 J4 HDMIULC6-4F3 4 TMDS channel A1 A3 C1 C3 D1 D3 F1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 F3 VDD_CEC A1 A3 C1 C3 D1 D3 F1 5V F3 27K HDMIULC6-4F3 B2 E2 5V CEC SCL SDA HPD TMDS DATA2 SHIELD TMDS DATA2 + TMDS DATA2TMDS DATA1 SHIELD TMDS DATA1 + TMDS DATA1TMDS DATA0 SHIELD TMDS DATA0 + TMDS DATA0TMDS CLK SHIELD TMDS CLK + TMDS CLKDDC / EEC GROUND CEC SCL SDA RESERVED +5V POWER HOT PLUG DETECT 2 x 1K75 100K HDMI05-CL02F3 Doc ID 15516 Rev 2 5/9 Ordering information scheme 3 HDMI05-CL02F3 Ordering information scheme Figure 17. Ordering information scheme HDMI 05 - CL 02 F3 Function HDMI = HDMI Protection Number of lines 05 = 5 lines Application CL = Control lines Version 02 = with CEC Pull-up integrated Package F3 = Flip Chip 0.4 mm pitch 4 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Figure 18. Flip Chip dimensions 400 µm ± 40 605 µm ± 55 1.14 mm ± 30 µm 400 µm ± 40 255 µm ± 40 1.14 mm ± 30 µm 6/9 Doc ID 15516 Rev 2 HDMI05-CL02F3 Package information Figure 19. Footprint Figure 20. Marking Dot, ST logo xx = marking z = manufacturing location yww = datecode (y = year ww = week) Copper pad Diameter: 220 µm recommended 260 µm maximum E Solder mask opening: 300 µm minimum x x z y ww Solder stencil opening : 220 µm recommended Figure 21. Flip Chip tape and reel specification Ø 1.5 ± 0.1 1.75 ± 0.1 3.5 ±- 0.1 1.24 xxz yww ST E xxz yww 1.24 ST E xxz yww ST E 8.0 ± 0.3 4.0 ± 0.1 4.0 ± 0.1 0.69 ± 0.05 All dimensions in mm User direction of unreeling Doc ID 15516 Rev 2 7/9 Ordering information 5 Ordering information Table 3. 6 Ordering information Order code Marking Package Weight Base qty Delivery mode HDMI05-CL02F3 JG Flip Chip 1.76 mg 5000 Tape and reel (7”) Revision history Table 4. 8/9 HDMI05-CL02F3 Document revision history Date Revision Changes 24-Mar-2009 1 First issue. 07-Apr-2010 2 Updated Figure 18. Doc ID 15516 Rev 2 HDMI05-CL02F3 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2010 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 15516 Rev 2 9/9