IR3500 DATA SHEET XPHASE3TM VR11.0 & AMD PVID CONTROL IC DESCRIPTION TM The IR3500 Control IC combined with an xPHASE3 Phase IC provides a full featured and flexible way to implement a complete VR11.0 or AMD PVID power solution. The Control IC provides overall system control and interfaces with any number of Phase ICs which each drive and monitor a single phase of a TM multiphase converter. The XPhase3 architecture implements a power supply that is smaller, less expensive, and easier to design while providing higher efficiency than conventional approaches. FEATURES • • • • • • • • • • • • • • • • • 1 to X phase operation with matching Phase IC VID Select pin configures AMD 5 or 6 bit PVID, Intel VR11 with/out startup to 1.1V Boot voltage 0.5% overall system set point accuracy Programmable 250kHz to 9MHz Daisy-chain digital phase timing clock oscillator frequency provides a per phase switching frequency of 250kHz to 1.5MHz without external components Programmable Dynamic VID Slew Rate Programmable VID Offset or No Offset Programmable Load Line Output Impedance High speed error amplifier with wide bandwidth of 30MHz and fast slew rate of 12V/us Programmable converter current limit during soft start, hiccup with delay during normal operation Central over voltage detection with programmable threshold and communication to phase ICs Over voltage signal output to system with overvoltage detection during powerup and normal operation Detection and protection of open remote sense line and open control loop IC bias linear regulator control with programmable output voltage and UVLO Programmable VRHOT function monitors temperature of power stage through a NTC thermistor Remote sense amplifier with true converter voltage sensing and less than 50uA bias current Simplified VR Ready output provides indication of proper operation and avoids false triggering Small thermally enhanced 32L 5mm x 5mm MLPQ package Optional To Converter FUSE Q1 12V VCCL RVCCLFB1 RVCCLFB2 RVCCLDRV CVCCL 4.7uF ROVP1 Q3 SCR Q2 ROVP2 VR READY CLKOUT 26 25 27 PHSIN PHSOUT 29 31 28 VCCL VCCLFB VCCLDRV 30 ENABLE EAOUT FB IIN VDRP 24 23 22 21 20 19 ROSC CSS/DEL RVDAC CVDAC 6 Wire Bus to Phase ICs ROCSET RVSETPT VDAC CDRP RCP 18 17 16 VID0 VO VID1 15 8 OCSET VSETPT 14 7 VID0 VDAC VID2 VOSEN+ VID1 VID3 VOSEN- 6 SS/DEL IR3500 CONTROL IC VID4 9 VID2 VID5 13 5 LGND ROSC / OVP 12 VID3 VID6 HOTSET 4 VRRDY VID4 VID7 VRHOT VID5 3 ENABLE 2 11 1 VID6 10 VID7 VIDSEL 32 VIDSEL VRHOT RFB1 RTHERMISTOR2 CFB RHOTSET2 RFB RDRP CCP CCP1 RTHERMISTOR1 VCC SENSE + To Load RHOTSET1 Close to Power Stage VSS SENSE VCCL RFB2 Figure 1 – Application Circuit Page 1 of 47 June 12, 2007 IR3500 ORDERING INFORMATION Device Package Order Quantity IR3500MTRPBF 32 Lead MLPQ 3000 per reel (5 x 5 mm body) * IR3500MPBF 32 Lead MLPQ *Samples only (5 x 5 mm body) 100 piece strips ABSOLUTE MAXIMUM RATINGS Stresses beyond those listed below may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications are not implied. o o Operating Junction Temperature…………….. 0 C to 150 C o o Storage Temperature Range………………….-65 C to 150 C ESD Rating………………………………………HBM Class 1C JEDEC Standard MSL Rating………………………………………2 o Reflow Temperature…………………………….260 C PIN # PIN NAME VMAX VMIN ISOURCE ISINK 1-8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 VID7-0 ENABLE VRHOT HOTSET VOSENVOSEN+ VO FB EAOUT VDRP IIN VSETPT OCSET VDAC SS/DEL ROSC/OVP 7.5V 3.5V 7.5V 7.5V 1.0V 7.5V 7.5V 7.5V 7.5V 7.5V 7.5V 3.5V 7.5V 3.5V 7.5V 7.5V -0.3V -0.3V -0.3V -0.3V -0.5V -0.5V -0.3V -0.3V -0.3V -0.3V -0.3V -0.3V -0.3V -0.3V -0.3V -0.3V 1mA 1mA 1mA 1mA 5mA 5mA 5mA 1mA 25mA 35mA 100mA 1mA 1mA 1mA 1mA 1mA 1mA 1mA 50mA 1mA 1mA 1mA 25mA 1mA 10mA 1mA 1mA 1mA 1mA 1mA 1mA 1mA 24 LGND n/a n/a 20mA 1mA 25 26 27 CLKOUT PHSOUT PHSIN 7.5V 7.5V 7.5V -0.3V -0.3V -0.3V 100mA 10mA 1mA 100mA 10mA 1mA 28 VCCL 7.5V -0.3V 1mA 20mA 29 VCCLFB 3.5V -0.3V 1mA 1mA 30 VCCLDRV 10V -0.3V 1mA 50mA 31 VRRDY VCCL + 0.3V -0.3V 1mA 20mA 32 VIDSEL 7.5V -0.3V 5mA 1mA Page 2 of 47 June 12, 2007 IR3500 RECOMMENDED OPERATING CONDITIONS FOR RELIABLE OPERATION WITH MARGIN o o 4.75V ≤ VCCL ≤ 7.5V, -0.3V ≤ VOSEN- ≤ 0.3V, 0 C ≤ TJ ≤ 100 C, 7.75KΩ ≤ ROSC ≤ 50.0 KΩ ELECTRICAL SPECIFICATIONS The electrical characteristics involve the spread of values guaranteed within the recommended operating conditions. Typical values represent the median values, which are related to 25°C. CSS/DEL = 0.1µF +/-10%. PARAMETER VDAC Reference System Set-Point Accuracy (Deviation from Tables 2 & 4 per test circuit in Fig.3 and Table 3 per test circuit in Fig.2) Source & Sink Currents VR11 VIDx Input Threshold AMD VIDx Input Threshold VR11 VIDx Input Bias Current AMD 6-bit VIDx Pull-down Resistance VIDx OFF State Blanking Delay VIDSEL Threshold between AMD 5-bit VID and AMD 6-bit VID VIDSEL Threshold between AMD 6-bit VID and VR11 with Boot Voltage VIDSEL Threshold between VR11 with/out Boot Voltage VIDSEL Float Voltage VIDSEL Pull-up Resistance Oscillator ROSC Voltage CLKOUT High Voltage CLKOUT Low Voltage PHSOUT Frequency PHSOUT Frequency PHSOUT Frequency PHSOUT High Voltage PHSOUT Low Voltage PHSIN Threshold Voltage Page 3 of 47 TEST CONDITION MIN TYP MAX UNIT % mV mV mV µA mV V VID ≥ 1V 0.8V ≤ VID < 1V 0.5V ≤ VID < 0.8V 0.3V ≤ VID < 0.5V Include OCSET and VSETPT currents Float VIDSEL or tie VIDSEL to VCCL R(VIDSEL) = 6.49kΩ or connect VIDSEL to LGND. Float VIDSEL, or connect VIDSEL to VCCL or LGND. 0V≤V(VIDx)≤2.5V. R(VIDSEL) = 6.49kΩ -0.5 -5 -8 -8 30 500 0.85 44 600 1.00 0.5 5 8 8 58 700 1.15 -1 0 1 µA 100 175 250 kΩ Measure time till VRRDY drives low Note 3. 0.5 0.48 1.3 0.6 2.1 0.75 µs V 84 87 90 % 2.97 3.30 3.63 V 77 83 89 % 2.5 3.5 4.5 KΩ 0.570 0.595 0.620 1 V V 1 275 550 1.65 1 V kHz kHz MHz V 1 70 V % Relative to VIDSEL float voltage. Note 3. Note 3. Relative to VIDSEL Threshold between VR11 with/out Boot Voltage I(CLKOUT)= -10 mA, measure V(VCCL) – V(CLKOUT). I(CLKOUT)= 10 mA ROSC = 50.0 KΩ ROSC = 24.5 KΩ ROSC = 7.75 KΩ I(PHSOUT)= -1 mA, measure V(VCCL) – V(PHSOUT) I(PHSOUT)= 1 mA Compare to V(VCCL) 225 450 1.35 250 500 1.50 30 50 June 12, 2007 IR3500 PARAMETER Soft Start and Delay Start Delay (TD1) Soft Start Time (TD2) VID Sample Delay (TD3) VRRDY Delay (TD4 + TD5) OC Delay Time SS/DEL to FB Input Offset Voltage Charge Current Discharge Current Charge/Discharge Current Ratio Charge Voltage Delay Comparator Threshold Delay Comparator Threshold TEST CONDITION To reach 1.1V V(IIN) – V(OCSET) = 500 mV With FB = 0V, adjust V(SS/DEL) until EAOUT drives high Relative to Charge Voltage, SS/DEL rising Relative to Charge Voltage, SS/DEL falling Delay Comparator Hysteresis VID Sample Delay Comparator Threshold Discharge Comp. Threshold Remote Sense Differential Amplifier Unity Gain Bandwidth Note 1 Input Offset Voltage 0.5V≤ V(VOSEN+) - V(VOSEN-) ≤ 1.6V Source Current 0.5V≤ V(VOSEN+) - V(VOSEN-) ≤ 1.6V Sink Current 0.5V≤ V(VOSEN+) - V(VOSEN-) ≤ 1.6V Slew Rate 0.5V≤ V(VOSEN+) - V(VOSEN-) ≤ 1.6V Note1 VOSEN+ Bias Current 0.5 V < V(VOSEN+) < 1.6V VOSEN- Bias Current -0.3V ≤ VOSEN- ≤ 0.3V, All VID Codes VOSEN+ Input Voltage Range V(VCCL)=7V High Voltage V(VCCL) – V(VO) Low Voltage V(VCCL)=7V Error Amplifier Input Offset Voltage Measure V(FB) – V(VSETPT). Note 2 FB Bias Current VSETPT Bias Current ROSC= 24.5 KΩ DC Gain Note 1 Bandwidth Note 1 Slew Rate Note 1 Sink Current Source Current Page 4 of 47 MIN TYP MAX UNIT 1.0 0.8 0.3 0.5 75 0.7 2.9 2.2 1.2 1.2 125 1.4 3.5 3.25 3.0 2.3 300 1.9 ms ms ms ms us V 35.0 2.5 10 3.6 50 52.5 4.5 12 4.0 80 70.0 6.5 16 4.2 125 µA µA µA/µA V mV 85 120 160 mV 10 2.8 30 3.0 60 3.2 mV V 150 200 250 mV 3.0 -3 0.5 2 2 6.4 0 1.0 12 4 9.0 3 1.7 18 8 MHz mV mA mA V/us 30 30 50 50 5.5 1 250 uA uA V V mV 1 1 25.50 120 40 20 1.00 12 mV 0.5 -1 -1 23.00 100 20 7 0.40 5 0 0 24.25 110 30 12 0.85 8 June 12, 2007 µA µA dB MHz V/µs mA mA IR3500 PARAMETER Minimum Voltage Maximum Voltage Open Voltage Loop Detection Threshold Open Voltage Loop Detection Delay Enable Input VR 11 Threshold Voltage VR 11 Threshold Voltage VR 11 Hysteresis AMD Threshold Voltage AMD Threshold Voltage AMD Hysteresis Bias Current Blanking Time TEST CONDITION MIN Measure V(VCCL) – V(EAOUT) Measure V(VCCL) - V(EAOUT), Relative to Error Amplifier maximum voltage. Measure PHSOUT pulse numbers from V(EAOUT) = V(VCCL) to VRRDY = low. 500 125 ENABLE rising ENABLE falling 825 775 25 1.1 1.05 30 -5 75 850 800 50 1.2 1.14 50 0 250 875 825 75 1.3 1.23 80 5 400 mV mV mV V V mV -30 23.25 -13 24.50 4096 2048 1024 0 25.75 mV -10 0.50 35 0.75 0 1.00 55 2.00 10 1.75 75 3.00 ENABLE rising ENABLE falling 0V ≤ V(ENABLE) ≤ 3.3V Noise Pulse < 100ns will not register an ENABLE state change. Note 1 Over-Current Comparator Input Offset Voltage 1V ≤ V(OCSET) ≤ 3.3V OCSET Bias Current ROSC= 24.5 KΩ Over-Current Delay Counter ROSC = 7.75 KΩ (PHSOUT=1.5MHz) Over-Current Delay Counter ROSC = 15.0 KΩ (PHSOUT=800kHZ) Over-Current Delay Counter ROSC = 50.0 KΩ (PHSOUT=250kHz) Over-Current Limit Amplifier Input Offset Voltage Transconductance Note 1 Sink Current Unity Gain Bandwidth Over Voltage Protection (OVP) Comparators Threshold at Power-up Threshold during Normal Compare to V(VDAC) Operation OVP Release Voltage during Compare to V(VDAC) Normal Operation Threshold during Dynamic VID down Dynamic VID Detect Comparator Threshold Propagation Delay to IIN Measure time from V(VO) > V(VDAC) (250mV overdrive) to V(IIN) transition to > 0.9 * V(VCCL). IIN Pull-up Resistance Propagation Delay to OVP Measure time from V(VO) > V(VDAC) (250mV overdrive) to V(ROSC/OVP) transition to >1V. OVP High Voltage Measure V(VCCL)-V(ROSC/OVP) OVP Power-up High Voltage V(VCCLDRV)=1.8V. Measure V(VCCL)V(ROSC/OVP) Page 5 of 47 TYP 120 780 300 MAX 250 950 600 8 UNIT mV mV mV Pulses µA ns µA Cycle Cycle Cycle mV mA/V uA kHz 1.60 105 1.73 125 1.83 145 V mV -13 3 20 mV 1.70 1.73 1.75 V 25 50 75 mV 90 180 ns 5 90 0 0 15 300 Ω ns 1.2 0.2 V V June 12, 2007 IR3500 PARAMETER VDRP Buffer Amplifier Input Offset Voltage Source Current Sink Current Unity Gain Bandwidth Slew Rate IIN Bias Current VRRDY Output Output Voltage Leakage Current Open Sense Line Detection Sense Line Detection Active Comparator Threshold Voltage Sense Line Detection Active Comparator Offset Voltage VOSEN+ Open Sense Line Comparator Threshold VOSEN- Open Sense Line Comparator Threshold Sense Line Detection Source Currents VRHOT Comparator Threshold Voltage HOTSET Bias Current Hysteresis Output Voltage VRHOT Leakage Current VCCL Regulator Amplifier Reference Feedback Voltage VCCLFB Bias Current VCCLDRV Sink Current UVLO Start Threshold UVLO Stop Threshold Hysteresis General VCCL Supply Current TEST CONDITION V(VDRP) – V(IIN), 0.5V ≤ V(IIN) ≤ 3.3V 0.5V ≤ V(IIN) ≤ 3.3V 0.5V ≤ V(IIN) ≤ 3.3V Note 1 Note 1 MIN TYP MAX UNIT -7 2 0.2 0 7 30 0.6 mV mA mA MHz -1 I(VRRDY) = 4mA V(VRRDY) = 5.5V V(VO) < [V(VOSEN+) – V(LGND)] / 2 Compare to V(VCCL) V(VO) = 100mV 1 300 10 150 200 250 mV 35 60 85 mV 87.5 90.0 92.5 % 0.36 0.40 0.44 V 200 500 700 uA 1.584 -1 75 1.600 0 100 150 0 1.616 1 125 400 10 V 1.15 -1 10 90 82 7 1.19 0 30 94 86 8.25 1.23 1 98 90 9.5 V uA mA % % % 3.0 6.5 10.0 mA Note 1: Guaranteed by design, but not tested in production Note 2: VDAC Output is trimmed to compensate for Error Amplifier input offset errors Note 3: See VIDSEL Functionality Table Page 6 of 47 V/µs µA 150 0 I(VRHOT) = 30mA V(VRHOT) = 5.5V Compare to V(VCCL) Compare to V(VCCL) Compare to V(VCCL) 0.4 8 4.7 0 June 12, 2007 mV µA µA mV mV µA IR3500 SYSTEM SET POINT TEST IR3500 ERROR AMPLIFIER VDAC BUFFER AMPLIFIER EAOUT 1k + - FB + VSETPT ISOURCE FAST VDAC RVDAC VDAC ISINK OCSET ROCSET - IVDAC IOCSET IVSETPT IROSC IROSC ROSC BUFFER AMPLIFIER 0.6V LGND + CURRENT SOURCE GENERATOR CVDAC IROSC ROSC ROSC VO EAOUT SYSTEM SET POINT VOSNSVOLTAGE REMOTE SENSE AMPLIFIER VOSEN+ + VOSEN- - Figure 2 - System Set Point Test Circuit for VR11 VID IR3500 ERROR AMPLIFIER VDAC BUFFER AMPLIFIER EAOUT + - FB + VSETPT RVSETPT ISOURCE FAST VDAC 1k VDAC RVDAC OCSET ISINK ROCSET - IVDAC IOCSET IVSETPT IROSC CVDAC ROSC BUFFER AMPLIFIER 0.6V LGND + IROSC CURRENT SOURCE GENERATOR IROSC ROSC ROSC VO EAOUT SYSTEM SET POINT VOSNSVOLTAGE REMOTE SENSE AMPLIFIER VOSEN+ VOSEN- + - Figure 3 - System Set Point Test Circuit for AMD VIDs (VDAC shifted +50 mV) Page 7 of 47 June 12, 2007 IR3500 PIN DESCRIPTION PIN# 1-8 9 PIN SYMBOL VID7-0 ENABLE 10 VRHOT 11 HOTSET 12 13 14 15 16 17 VOSENVOSEN+ VO FB EAOUT VDRP 18 IIN 19 VSETPT 20 OCSET 21 VDAC 22 SS/DEL 23 ROSC/OVP 24 25 LGND CLKOUT 26 PHSOUT 27 28 PHSIN VCCL 29 VCCLFB Page 8 of 47 PIN DESCRIPTION Inputs to VID D to A Converter. Enable input. A logic low applied to this pin puts the IC into fault mode. Do not float this pin as the logic state will be undefined. Open collector output of the VRHOT comparator which drives low if HOTSET pin voltage is lower than 1.6V. Connect external pull-up. A resistor divider including thermistor senses the temperature, which is used for VRHOT comparator. Remote sense amplifier input. Connect to ground at the load. Remote sense amplifier input. Connect to output at the load. Remote sense amplifier output. Inverting input to the error amplifier. Output of the error amplifier. Buffered IIN signal. Connect an external RC network to FB to program converter output impedance. Average current input from the phase IC(s). This pin is also used to communicate over voltage condition to phase ICs. Error amplifier non-inverting input. Converter output voltage can be decreased from the VDAC voltage with an external resistor connected between VDAC and this pin (there is an internal sink current at this pin). Programs the constant converter output current limit and hiccup over-current thresholds through an external resistor tied to VDAC and an internal current source from this pin. Over-current protection can be disabled by connecting a resistor from this pin to VDAC to program the threshold higher than the possible signal into the IIN pin from the phase ICs but no greater than VCCL – 2V (do not float this pin as improper operation will occur). Regulated voltage programmed by the VID inputs. Connect an external RC network to LGND to program dynamic VID slew rate and provide compensation for the internal buffer amplifier. Programs converter startup and over current protection delay timing. It is also used to compensate the constant output current loop during soft start. Connect an external capacitor to LGND to program. Connect a resistor to LGND to program oscillator frequency and OCSET, VSETPT and VDAC bias currents. Oscillator frequency equals switching frequency per phase. The pin voltage is 0.6V during normal operation and higher than 1.6V if over-voltage condition is detected. Local Ground for internal circuitry and IC substrate connection. Clock output at switching frequency multiplied by phase number. Connect to CLKIN pins of phase ICs. Phase clock output at switching frequency per phase. Connect to PHSIN pin of the first phase IC. Feedback input of phase clock. Connect to PHSOUT pin of the last phase IC. Output of the voltage regulator, and power input for clock oscillator circuitry. Connect a decoupling capacitor to LGND. Non-inverting input of the voltage regulator error amplifier. Output voltage of the regulator is programmed by the resistor divider connected to VCCL. June 12, 2007 IR3500 30 VCCLDRV 31 VRRDY 32 VIDSEL Output of the VCCL regulator error amplifier to control external transistor. The pin senses 12V power supply through a resistor. Open collector output that drives low during startup and under any external fault condition. Connect external pull-up. The pin configures VIDs for AMD 6-bit, Intel VR11 8-bit with 1.1V Boot voltage, Intel VR11 8-bit without 1.1V Boot voltage or AMD 5-bit Opteron. SYSTEM THEORY OF OPERATION PWM Control Method TM The PWM block diagram of the XPhase3 architecture is shown in Figure 4. Feed-forward voltage mode control with trailing edge modulation is used. A high-gain wide-bandwidth voltage type error amplifier in the Control IC is used for the voltage control loop. Input voltage is sensed in phase ICs and feed-forward control is realized. The PWM ramp slope will change with the input voltage and automatically compensate for changes in the input voltage. The input voltage can change due to variations in the silver box output voltage or due to the wire and PCB-trace voltage drop related to changes in load current. GATE DRIVE VOLTAGE CONTROL IC VIN PHSOUT PHASE IC CLOCK GENERATOR CLKOUT VCC CLKIN CLK Q VCCH D PHSOUT 1 PHSIN 1 PWM COMPARATOR CBST SW 5 CLK Q VOUT COUT - EAIN VCCL + GND PWM LATCH GATEL ENABLE + REMOTE SENSE AMPLIFIER + VID6 BODY BRAKING COMPARATOR PGND VOSNS- - - - LDO AMPLIFIER + RAMP DISCHARGE CLAMP VO VDAC SHARE ADJUST ERROR AMPLIFIER EAOUT ISHARE - CURRENT SENSE AMPLIFIER VID6 VID6 - + + - 3K RCOMP RFB1 RFB + CCOMP FB RVSETPT IVSETPT IROSC VDRP AMP CSIN+ + CCOMP1 VID6 VID6 + CFB RCS CSIN- DACIN RDRP1 PHSOUT PHASE IC RDRP VSETPT CCS - VDAC + + - LGND ERROR AMPLIFIER CDRP VDRP VCC CLK Q CLKIN + - D IIN 1 VCCH RESET DOMINANT 2 PHSIN 1 Q CLK Q GATEH 4 CBST 5 SW R 2 D 3 PWM COMPARATOR EAIN + VCCL PWM LATCH ENABLE + VID6 - RAMP DISCHARGE CLAMP GATEL BODY BRAKING COMPARATOR PGND - + SHARE ADJUST ERROR AMPLIFIER CURRENT SENSE AMPLIFIER + - VID6 VID6 + CSIN+ VID6 VID6 + + DACIN CCS RCS - - 3K + ISHARE CSIN- Figure 4 - PWM Block Diagram Page 9 of 47 VOSNS+ 4 Q R 2 D 3 PHSIN GATEH RESET DOMINANT 2 June 12, 2007 IR3500 Frequency and Phase Timing Control The oscillator and system clock frequency is programmable from 250kHz to 9MHZ by an external resistor (ROSC). The control IC system clock signal (CLKOUT) is connected to CLKIN of all the phase ICs. The phase timing of the phase ICs is controlled by the daisy chain loop, where control IC phase clock output (PHSOUT) is connected to the phase clock input (PHSIN) of the first phase IC, and PHSOUT of the first phase IC is connected to PHSIN of the second phase IC, etc. and PHSOUT of the last phase IC is connected back to PHSIN of the control IC. During power up, the control IC sends out clock signals from both CLKOUT and PHSOUT pins and detects the feedback at PHSIN pin to determine the phase number and monitor any fault in the daisy chain loop. Figure 5 shows the phase timing for a four phase converter. The switching frequency is set by the resistor ROSC as shown in Figure 23. The clock frequency equals the number of phase times the switching frequency. Control IC CLKOUT (Phase IC CLKIN) Control IC PHSOUT (Phase IC1 PHSIN) Phase IC1 PWM Latch SET Phase IC 1 PHSOUT (Phase IC2 PHSIN) Phase IC 2 PHSOUT (Phase IC3 PHSIN) Phase IC 3 PHSOUT (Phase IC4 PHSIN) Phase IC4 PHSOUT (Control IC PHSIN) Figure 5 - Four Phase Oscillator Waveforms PWM Operation The PWM comparator is located in the phase IC. Upon receiving the falling edge of a clock pulse, the PWM latch is set; the PWM ramp voltage begins to increase; the low side driver is turned off, and the high side driver is then turned on after the non-overlap time. When the PWM ramp voltage exceeds the error amplifier’s output voltage the PWM latch is reset. This turns off the high side driver, then turns on the low side driver after the non-overlap time, and activates the ramp discharge clamp. The ramp discharge clamp quickly discharges the PWM ramp capacitor to the output voltage of the share adjust amplifier in the phase IC until the next clock pulse. The PWM latch is reset dominant allowing all phases to go to zero duty cycle within a few tens of nanoseconds in response to a load step decrease. Phases can overlap and go up to 100% duty cycle in response to a load step increase with turn-on gated by the clock pulses. An error amplifier output voltage greater than the common mode input range of the PWM comparator results in 100% duty cycle regardless of the voltage of the PWM ramp. This arrangement guarantees the error amplifier is always in control and can demand 0 to 100% duty cycle as required. It also favors response to a load step decrease which is appropriate given the low output to input voltage ratio of Page 10 of 47 June 12, 2007 IR3500 most systems. The inductor current will increase much more rapidly than decrease in response to load transients. An additional advantage of the architecture is that differences in ground or input voltage at the phases have no effect on operation since the PWM ramps are referenced to VDAC. Figure 6 depicts PWM operating waveforms under various conditions. The error amplifier is a high speed amplifier with 110 dB of open loop gain. It is not unity gain stable. PHASE IC CLOCK PULSE EAIN PWMRMP VDAC GATEH GATEL STEADY-STATE OPERATION DUTY CYCLE INCREASE DUE TO LOAD INCREASE DUTY CYCLE DECREASE DUE TO VIN INCREASE (FEED-FORWARD) DUTY CYCLE DECREASE DUE TO LOAD DECREASE (BODY BRAKING) OR FAULT (VCC UV, OCP, VID FAULT) STEADY-STATE OPERATION Figure 6 - PWM Operating Waveforms Body Braking TM In a conventional synchronous buck converter, the minimum time required to reduce the current in the inductor in response to a load step decrease is; TSLEW = L * ( I MAX − I MIN ) VO The slew rate of the inductor current can be significantly increased by turning off the synchronous rectifier in response to a load step decrease. The switch node voltage is then forced to decrease until conduction of the synchronous rectifier’s body diode occurs. This increases the voltage across the inductor from Vout to Vout + VBODYDIODE. The minimum time required to reduce the current in the inductor in response to a load transient decrease is now; TSLEW = L * ( I MAX − I MIN ) VO + VBODYDIODE Since the voltage drop in the body diode is often comparable to the output voltage, the inductor current slew rate can be increased significantly. This patented method is referred to as “body braking” and is accomplished through the “body braking comparator” located in the phase IC. If the error amplifier’s output voltage drops below the output voltage of the share adjust amplifier in the phase IC, this comparator turns off the low side gate driver. Lossless Average Inductor Current Sensing Inductor current can be sensed by connecting a series resistor and a capacitor network in parallel with the inductor and measuring the voltage across the capacitor, as shown in Figure 7. The equation of the sensing network is, Page 11 of 47 June 12, 2007 IR3500 vC ( s ) = vL ( s ) 1 RL + sL = iL ( s ) 1 + sRCS CCS 1 + sRCS CCS Usually the resistor Rcs and capacitor Ccs are chosen so that the time constant of Rcs and Ccs equals the time constant of the inductor which is the inductance L over the inductor DCR (RL). If the two time constants match, the voltage across Ccs is proportional to the current through L, and the sense circuit can be treated as if only a sense resistor with the value of RL was used. The mismatch of the time constants does not affect the measurement of inductor DC current, but affects the AC component of the inductor current. vL iL Current Sense Amp L RL RCS CCS VO CO c vCS CSOUT Figure 7 - Inductor Current Sensing and Current Sense Amplifier The advantage of sensing the inductor current versus high side or low side sensing is that actual output current being delivered to the load is obtained rather than peak or sampled information about the switch currents. The output voltage can be positioned to meet a load line based on real time information. Except for a sense resistor in series with the inductor, this is the only sense method that can support a single cycle transient response. Other methods provide no information during either load increase (low side sensing) or load decrease (high side sensing). An additional problem associated with peak or valley current mode control for voltage positioning is that they suffer from peak-to-average errors. These errors will show in many ways but one example is the effect of frequency variation. If the frequency of a particular unit is 10% low, the peak to peak inductor current will be 10% larger and the output impedance of the converter will drop by about 10%. Variations in inductance, current sense amplifier bandwidth, PWM prop delay, any added slope compensation, input voltage, and output voltage are all additional sources of peak-to-average errors. Current Sense Amplifier A high speed differential current sense amplifier is located in the phase IC, as shown in Figure 7. Its gain is nominally 32.5 and the 3850 ppm/ºC increase in inductor DCR should be compensated in the voltage loop feedback path. The current sense amplifier can accept positive differential input up to 50mV and negative up to -10mV before clipping. The output of the current sense amplifier is summed with the DAC voltage and sent to the control IC and other phases through an on-chip 3KΩ resistor connected to the ISHARE pin. The ISHARE pins of all the phases are tied together and the voltage on the share bus represents the average current through all the inductors and is used by the control IC for voltage positioning and current limit protection. The input offset of this amplifier is calibrated to +/- 1mV in order to reduce the current sense error. The input offset voltage is the primary source of error for the current share loop. In order to achieve very small input offset error and superior current sharing performance, the current sense amplifier continuously calibrates itself. This calibration algorithm creates ripple on ISHARE bus with a frequency of fsw / 896 in a multiphase architecture. Page 12 of 47 June 12, 2007 IR3500 Average Current Share Loop Current sharing between phases of the converter is achieved by the average current share loop in each phase IC. The output of the current sense amplifier is compared with average current at the share bus. If current in a phase is smaller than the average current, the share adjust amplifier of the phase will pull down the starting point of the PWM ramp thereby increasing its duty cycle and output current; if current in a phase is larger than the average current, the share adjust amplifier of the phase will pull up the starting point of the PWM ramp thereby decreasing its duty cycle and output current. The current share amplifier is internally compensated so that the crossover frequency of the current share loop is much slower than that of the voltage loop and the two loops do not interact. IR3500 THEORY OF OPERATION Block Diagram The Block diagram of the IR3500 is shown in Figure 8, and specific features are discussed in the following sections. VID Control The AMD 6-bit VID, VR11 8-bit VID, and AMD Opteron 5-bit VID are shown in Tables 2 to 4 respectively, and are selected by different connections of VIDSEL pin shown in Table 1. The VID pins require an external bias voltage and should not be floated. The VID input comparators monitor the VID pins and control the Digital-to-Analog Converter (DAC) whose output is sent to the VDAC buffer amplifier. The output of the buffer amplifier is the VDAC pin. The VDAC voltage, input offsets of error amplifier and remote sense differential amplifier are post-package trimmed to provide 0.5% system set-point accuracy. The actual VDAC voltage does not determine the system accuracy, which has a wider tolerance. VIDs of less than 0.5V are not supported. The IR3500 can accept changes in the VID code while operating and vary the DAC voltage accordingly. The slew rate of the voltage at the VDAC pin can be adjusted by an external capacitor between VDAC pin and LGND pin. A resistor connected in series with this capacitor is required to compensate the VDAC buffer amplifier. Digital VID transitions result in a smooth analog transition of the VDAC voltage and converter output voltage minimizing inrush currents in the input and output capacitors and overshoot of the output voltage. Adaptive Voltage Positioning Adaptive voltage positioning is needed to reduce the output voltage deviations during load transients and the power dissipation of the load at heavy load. The circuitry related to voltage positioning is shown in Figure 9. The output voltage is set by the reference voltage VSETPT at the positive input to the error amplifier. This reference voltage can be programmed to have a constant DC offset bellow the VDAC by connecting RSETPT between VDAC and VSETPT. The IVSETPT is controlled by the ROSC as shown in Figure 24. The voltage at the VDRP pin is a buffered version of the share bus IIN and represents the sum of the DAC voltage and the average inductor current of all the phases. The VDRP pin is connected to the FB pin through the resistor RDRP. Since the error amplifier will force the loop to maintain FB to be equal to the VSETPT, an additional current will flow into the FB pin equal to (VDRP-VSETPT) / RDRP. When the load current increases, the adaptive positioning voltage increases accordingly. More current flows through the feedback resistor RFB, and makes the output voltage lower proportional to the load current. The positioning voltage can be programmed by the resistor RDRP so that the droop impedance produces the desired converter output impedance. The offset and slope of the converter output impedance are referenced to and therefore independent of the VDAC voltage. Inductor DCR Temperature Compensation A negative temperature coefficient (NTC) thermistor should be used for inductor DCR temperature compensation. The thermistor should be placed close to the inductor and connected in parallel with the feedback resistor, as shown in Figure 10. The resistor in series with the thermistor is used to reduce the nonlinearity of the thermistor. Page 13 of 47 June 12, 2007 ENABLE COMPARATOR 250nS BLANKING DELAY COMPARATOR POWER OK LATCH + DISCHARGE COMPARATOR + 4.0V R - 0.94 1.19V SS RESET + VCCL OUTPUT COMPARATOR 0.86 OC DELAY RESET 0.2V 8-Pulse Delay + OPEN SENSE LINE OPEN DAISY CHAIN OPEN VOLTAGE LOOP + AMD 5-BIT VID2 VID2 VID3 - VID3 + VID4 VID4 VID1AMD 1.0V VID0 VID0INTEL 0.6V SAMPLE DELAY 3.2V OV FAULT SOFT START 1.4V CLAMP DIS IDCHG 4.5uA OV@OPERATION S VCCL UVLO 1.6V REMOTE SENSE AMPLIFIER DYNAMIC VID DETECT COMPARATOR 25k + VO - + OV@OPERATION IROSC OPEN SENSE LINE DETECT COMPARATORS ISINK - 25k + - VDAC VO IVOSEN+ VOSENIVOSENIVOSEN- DETECTION VCCL PULSE SS RESET VCCL OPEN SENSE LINE DETECT COMPARATORS VCCL*0.9 - + ROSC/OVP VOSEN+ 25k VIDSEL - CURRENT SOURCE GENERATOR ISOURCE OV@START + + 200mV OPEN SENSE LINE ENABLE 0.4V + IR3500 June 12, 2007 VCCLDRV ROSC BUFFER AMPLIFIER VDAC BUFFER AMPLIFIER + IROSC OV FAULT R POWER-UP OV 1.73V COMPARATOR 25k 60mV 50mV Q SET DOMINANT - PHSOUT PHSIN OV@START OV FAULT LATCH Q PHSIN 0.6V ISETPT + OPEN DAISY CHAIN LGND VSETPT IROSC PULSE FAULT VCCL-1.2V EAOUT FB - R VDRP DISABLE OVER 130mV VOLTAGE 3mV COMPARATOR DETECTION S VID0 VCCL UVLO PHSOUT VID SAMPLE DELAY FAULT LATCH1 COMPARATOR VID1 CLKOUT VID0 CLKOUT S VR11 NoBOOT FAST VDAC VID1 VDRP AMPLIFIER IOCSET ERROR AMPLIFIER - VID5 IROSC + VID6 VID7 VID INPUT VID6 COMPARATORS VID5 (1/8 SHOWN) OV@OPERATION - VID7 1.3uS VID FAULT BLANKING DIGITAL VID7 VIDSEL VBOOT TO ANALOG LATCH VID6 CONVERTER VID5 VBOOT (1.1V) Q S VIDSEL SET VBOOT VID4 DOMINANT DVID VID3 INTERNAL R VID2 VDAC R VCCL OV@START + VIDSEL VR11 BOOT Q SET DOMINANT OCSET OC LIMIT AMPLIFIER R Q SET DOMINANT AMD 6-BIT + 1.6V 1.5V IIN + Figure 8 - Block Diagram 3.5k VCCL UVLO - - VIDSEL VIDSEL VIDSEL COMPARATORS 3.3V VIDSEL VIDSEL VID FAULT LATCH LATCH VID FAULT 0.86 S OC LIMIT COMPARATOR - EAOUT - 0.6V HOTSET VRHOT UV CLEARED FAULT LATCH2 OC 1.08V VCCL VCCL UVLO OC DELAY PHSOUT COUNTER SS/DEL Float Voltage VRHOT COMPARATOR R IROSC SAMPLE DELAY VCCLFB FAULT LATCH2 OV FAULT + 80mV 120mV VCCL REGULATOR AMPLIFIER Q SET DOMINANT SS RESET S Q RESET DOMINANT - VCCLDRV S VID FAULT LATCH VCCL UVLO OC before VRRDY + AMD 1.2V 1.14V VRRDY POWER NOT OK FAULT LATCH1 + + + INTEL 850mV 800mV SS CLEARED FAULT LATCH1 OC after VRRDY DISABLE VID FAULT - - - VBIAS + Page 14 of 47 VCCL ENABLE IR3500 TABLE 1 - VIDSEL FUNCTIONALITY VIDSEL Connection LGND (<0.5V) 6.49 kΩ to GND (0.7V to 83% of FLOAT) FLOAT (typ. 83% of VR11w/wo boot Threshold) VCCL (4.5V-7V) VID Table Ignore VID Fault during soft start? NO NO VID Fault Latch? AMD 5-BIT OPTERON AMD 6-BIT 1.1V Boot Voltage during soft start? NO NO VR11 8-BIT YES YES YES VR11 8-BIT NO NO NO NO NO TABLE 2 - AMD 6-BIT VID TABLE VID5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 VID4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VID3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 VID2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 VID1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 VID0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Vout (V) 1.5500 1.5250 1.5000 1.4750 1.4500 1.4250 1.4000 1.3750 1.3500 1.3250 1.3000 1.2750 1.2500 1.2250 1.2000 1.1750 1.1500 1.1250 1.1000 1.0750 1.0500 1.0250 1.0000 0.9750 0.9500 0.9250 0.9000 0.8750 0.8500 0.8250 0.8000 0 1 1 1 1 1 0.7750 VID5 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VID4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VID3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 VID2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 VID1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 VID0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 Vout(V) 0.7625 0.7500 0.7375 0.7250 0.7125 0.7000 0.6875 0.6750 0.6625 0.6500 0.6375 0.6250 0.6125 0.6000 0.5875 0.5750 0.5625 0.5500 0.5375 0.5250 0.5125 0.5000 n/a n/a n/a n/a n/a n/a n/a n/a n/a 1 1 1 1 1 1 n/a Note: 6.49kΩ connected between VID_SEL and LGND. V(VDAC) is pre-positioned 50mV higher than VID values listed above for load line positioning. VID is measured at EAOUT with EAOUT shorted to FB, ROSC=50 KΩ and a 4200 Ω resistor connecting VSETPT to VDAC to cancel the 50 mV pre-position offset, as shown in Fig. 3. Page 15 of 47 June 12, 2007 IR3500 TABLE 3 - VR11 VID TABLE (PART1) Hex (VID7:VID0) 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F Page 16 of 47 Dec (VID7:VID0) 00000000 00000001 00000010 00000011 00000100 00000101 00000110 00000111 00001000 00001001 00001010 00001011 00001100 00001101 00001110 00001111 00010000 00010001 00010010 00010011 00010100 00010101 00010110 00010111 00011000 00011001 00011010 00011011 00011100 00011101 00011110 00011111 00100000 00100001 00100010 00100011 00100100 00100101 00100110 00100111 00101000 00101001 00101010 00101011 00101100 00101101 00101110 00101111 00110000 00110001 00110010 00110011 00110100 00110101 00110110 00110111 00111000 00111001 00111010 00111011 00111100 00111101 00111110 00111111 Voltage Fault Fault 1.60000 1.59375 1.58750 1.58125 1.57500 1.56875 1.56250 1.55625 1.55000 1.54375 1.53750 1.53125 1.52500 1.51875 1.51250 1.50625 1.50000 1.49375 1.48750 1.48125 1.47500 1.46875 1.46250 1.45625 1.45000 1.44375 1.43750 1.43125 1.42500 1.41875 1.41250 1.40625 1.40000 1.39375 1.38750 1.38125 1.37500 1.36875 1.36250 1.35625 1.35000 1.34375 1.33750 1.33125 1.32500 1.31875 1.31250 1.30625 1.30000 1.29375 1.28750 1.28125 1.27500 1.26875 1.26250 1.25625 1.25000 1.24375 1.23750 1.23125 1.22500 1.21875 Hex (VID7:VID0) 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F Dec (VID7:VID0) 01000000 01000001 01000010 01000011 01000100 01000101 01000110 01000111 01001000 01001001 01001010 01001011 01001100 01001101 01001110 01001111 01010000 01010001 01010010 01010011 01010100 01010101 01010110 01010111 01011000 01011001 01011010 01011011 01011100 01011101 01011110 01011111 01100000 01100001 01100010 01100011 01100100 01100101 01100110 01100111 01101000 01101001 01101010 01101011 01101100 01101101 01101110 01101111 01110000 01110001 01110010 01110011 01110100 01110101 01110110 01110111 01111000 01111001 01111010 01111011 01111100 01111101 01111110 01111111 June 12, 2007 Voltage 1.21250 1.20625 1.20000 1.19375 1.18750 1.18125 1.17500 1.16875 1.16250 1.15625 1.15000 1.14375 1.13750 1.13125 1.12500 1.11875 1.11250 1.10625 1.10000 1.09375 1.08750 1.08125 1.07500 1.06875 1.06250 1.05625 1.05000 1.04375 1.03750 1.03125 1.02500 1.01875 1.01250 1.00625 1.00000 0.99375 0.98750 0.98125 0.97500 0.96875 0.96250 0.95625 0.95000 0.94375 0.93750 0.93125 0.92500 0.91875 0.91250 0.90625 0.90000 0.89375 0.88750 0.88125 0.87500 0.86875 0.86250 0.85625 0.85000 0.84375 0.83750 0.83125 0.82500 0.81875 IR3500 TABLE 3 - VR11 VID TABLE (PART 2) Hex (VID7:VID0) 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF Page 17 of 47 Dec (VID7:VID0) 10000000 10000001 10000010 10000011 10000100 10000101 10000110 10000111 10001000 10001001 10001010 10001011 10001100 10001101 10001110 10001111 10010000 10010001 10010010 10010011 10010100 10010101 10010110 10010111 10011000 10011001 10011010 10011011 10011100 10011101 10011110 10011111 10100000 10100001 10100010 10100011 10100100 10100101 10100110 10100111 10101000 10101001 10101010 10101011 10101100 10101101 10101110 10101111 10110000 10110001 10110010 10110011 10110100 10110101 10110110 10110111 10111000 10111001 10111010 10111011 10111100 10111101 10111110 10111111 Voltage 0.81250 0.80625 0.80000 0.79375 0.78750 0.78125 0.77500 0.76875 0.76250 0.75625 0.75000 0.74375 0.73750 0.73125 0.72500 0.71875 0.71250 0.70625 0.70000 0.69375 0.68750 0.68125 0.67500 0.66875 0.66250 0.65625 0.65000 0.64375 0.63750 0.63125 0.62500 0.61875 0.61250 0.60625 0.60000 0.59375 0.58750 0.58125 0.57500 0.56875 0.56250 0.55625 0.55000 0.54375 0.53750 0.53125 0.52500 0.51875 0.51250 0.50625 0.50000 n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a Hex (VID7:VID0) C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF Dec (VID7:VID0) 11000000 11000001 11000010 11000011 11000100 11000101 11000110 11000111 11001000 11001001 11001010 11001011 11001100 11001101 11001110 11001111 11010000 11010001 11010010 11010011 11010100 11010101 11010110 11010111 11011000 11011001 11011010 11011011 11011100 11011101 11011110 11011111 11100000 11100001 11100010 11100011 11100100 11100101 11100110 11100111 11101000 11101001 11101010 11101011 11101100 11101101 11101110 11101111 11110000 11110001 11110010 11110011 11110100 11110101 11110110 11110111 11111000 11111001 11111010 11111011 11111100 11111101 11111110 11111111 June 12, 2007 Voltage n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a n/a FAULT FAULT IR3500 TABLE 4 - AMD 5-BIT TABLE FOR OPTERON VID4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 VID3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 VID2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 VID1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 VID0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Voltage (V) 1.550 1.525 1.500 1.475 1.450 1.425 1.400 1.375 1.350 1.325 1.300 1.275 1.250 1.225 1.200 1.175 1.150 1.125 1.100 1.075 1.050 1.025 1.000 0.975 0.950 0.925 0.900 0.875 0.850 0.825 0.800 FAULT Note: VID_SEL tied to LGND. V(VDAC) is pre-positioned 50mV higher than VID values listed above for load line positioning. VID is measured at EAOUT with EAOUT shorted to FB, ROSC=50 KΩ and a 4200 Ω resistor connecting VSETPT to VDAC to cancel the 50 mV pre-position offset, as shown in Fig. 3. Page 18 of 47 June 12, 2007 IR3500 Control IC VDAC VDAC Phase IC Current Sense Amplif ier ISHARE 3k VDAC + ... ... FB RFB VDRP Amplifier VDRP Phase IC RDRP Current Sense Amplif ier ISHARE VO VDAC + VOSEN+ - VOSEN- 3k CSIN+ - + IIN + - Remote Sense Amplifier CSIN- EAOUT - IVSETPT CSIN+ - VSETPT Error Amplifier + RSETPT CSIN- Figure 9 - Adaptive voltage positioning Control IC VDAC VDAC RSETPT VSETPT Error Amplifier + EAOUT RFB - IVSETPT FB VDRP Amplifier + RFB1 Rt RDRP VDRP IIN VO + VOSEN+ - Remote Sense Amplifier VOSEN- Figure 10 - Temperature compensation of inductor DCR Remote Voltage Sensing VOSEN+ and VOSEN- are used for remote sensing and connected directly to the load. The remote sense differential amplifier with high speed, low input offset and low input bias current ensures accurate voltage sensing and fast transient response. Start-up Sequence The IR3500 has a programmable soft-start function to limit the surge current during the converter start-up. A capacitor connected between the SS/DEL and LGND pins controls soft start timing, over-current protection delay and hiccup mode timing. A charge current of 52.5uA and discharge current of 4uA control the up slope and down slope of the voltage at the SS/DEL pin respectively. Page 19 of 47 June 12, 2007 IR3500 Figure 11 depicts start-up sequence of converter with VR 11 VID with boot voltage, which is selected by VIDSEL pin based on Table 1. If there is no fault, the SS/DEL pin will start charging when the enable crosses the threshold. The error amplifier output EAOUT is clamped low until SS/DEL reaches 1.4V. The error amplifier will then regulate the converter’s output voltage to match the SS/DEL voltage less the 1.4V offset until the converter output reaches the 1.1V boot voltage. The SS/DEL voltage continues to increase until it rises above the 3.0V threshold of VID delay comparator. The VID set inputs are then activated and VDAC pin transitions to the level determined by the VID inputs. The SS/DEL voltage continues to increase until it rises above 3.92V and allows the VRRDY signal to be asserted. SS/DEL finally settles at 4.0V, indicating the end of the soft start. Figure 12 shows start-up sequence of converter VR 11 VID without boot voltage or AMD Opteron, AMD 6-bit VID which is selected by VIDSEL pin based on Table 1. If there is no fault, the SS/DEL pin will start charging. The error amplifier output EAOUT is clamped low until SS/DEL reaches 1.4V. The error amplifier will then regulate the converter’s output voltage to match the SS/DEL voltage less the 1.4V offset until the converter output reaches the level determined by the VID inputs. The SS/DEL voltage continues to increase until it rises above 3.92V and allows the VRRDY signal to be asserted. SS/DEL finally settles at 4.0V, indicating the end of the soft start. VCC (12V) ENABLE VID 1.1V VDAC 4.0V 3.92V 3V 1.4V SS/DEL EAOUT VOUT VRRDY START DELAY (TD1) SOFT START TIME (TD2) VID SAMPLE TIME (TD3) VRRDY DELAY TIME (TD4+TD5) TD4 NORMAL OPERATION TD5 Figure 11 - Start-up sequence of converter with boot voltage VCCL under voltage lock-out, VID fault modes, over current, as well as a low signal on the ENABLE input immediately sets the fault latch, which causes the EAOUT pin to drive low turning off the phase IC drivers. The VRRDY pin also drives low, and SS/DEL begin to discharge until the voltage reaches 0.2V. If the fault has cleared the fault latch will be reset by the discharge comparator allowing a normal soft start to occur. Other fault conditions, such as over voltage, open sense lines, open loop monitor, and open daisy chain, set different fault latches, which start discharging SS/DEL, pull down EAOUT voltage and drive VRRDY low. However, the latches can only be reset by cycling VCCL power. Page 20 of 47 June 12, 2007 IR3500 VCC (12V) ENABLE VID VDAC 4.0V 3.92V 1.4V SS/DEL EAOUT VOUT VRRDY START DELAY (TD1) SOFT START TIME (TD2) VRRDY DELAY TIME (TD3) NORMAL OPERATION Figure 12 - Start-up sequence of converter without boot voltage Constant Over-Current Control during Soft Start The over current limit threshold is set by a resistor connected between OCSET and VDAC. If the IIN pin voltage, which is proportional to the average current plus VDAC voltage, exceeds the OCSET voltage during soft start, the constant over-current control is activated. Figure 13 shows the constant over-current control with delay during soft start. The delay time is set by the ROSC resistor, which sets the number of switching cycles for the delay counter. The delay is required since over-current conditions can occur as part of normal operation due to inrush current. If an over-current occurs during soft start (before VRRDY is asserted), the SS/DEL voltage is regulated by the over current amplifier to limit the output current below the threshold set by OCSET voltage. If the over-current condition persists after delay time is reached, the fault latch will be set pulling the error amplifier’s output low and inhibiting switching in the phase ICs. The SS/DEL capacitor will discharge until it reaches 0.2V and the fault latch is reset allowing a normal soft start to occur. If an over-current condition is again encountered during the soft start cycle, the constant over-current control actions will repeat and the converter will be in hiccup mode. The delay time is controlled by a counter which is triggered by clock. The counter values vary with switching frequency per phase in order to have a similar delay time for different switching frequencies. Over-Current Hiccup Protection after Soft Start The over current limit threshold is set by a resistor connected between OCSET and VDAC pins. Figure 13 shows the constant over-current control with delay after VRRDY is asserted. The delay is required since over-current conditions can occur as part of normal operation due to load transients or VID transitions. If the IIN pin voltage, which is proportional to the average current plus VDAC voltage, exceeds the OCSET voltage after VRRDY is asserted, it will initiate the discharge of the capacitor at SS/DEL. The magnitude of the discharge current is proportional to the voltage difference between IIN and OCSET and has a maximum nominal value of 55uA. If the over-current condition persists long enough for the SS/DEL capacitor to discharge below the 120mV offset of the delay comparator, the fault latch will be set pulling the error amplifier’s output low and inhibiting switching in the phase ICs and de-asserting the VRRDY signal. The output current is not controlled during the delay time. The SS/DEL capacitor will discharge until it reaches 200 mV and the fault latch is reset allowing a normal soft start to occur. If an over-current condition is again encountered during the soft start cycle, the over-current action will repeat and the converter will be in hiccup mode. Page 21 of 47 June 12, 2007 IR3500 ENABLE INTERNAL OC DELAY SS/DEL 4.0V 3.92V 3.88V 1.1V EA VOUT VRRDY OCP THRESHOLD IOUT START-UP WITH OUTPUT SHORTED HICCUP OVER-CURRENT PROTECTION (OUTPUT SHORTED) NORMAL START-UP OCP DELAY OVER-CURRENT NORMAL NORMAL PROTECTION START-UP OPERATION POWER-DOWN (OUTPUT SHORTED) (OUTPUT NORMAL OPERATION SHORTED) Figure 13 - Over Current Protection waveforms during and after soft start Linear Regulator Output (VCCL) The IR3500 has a built-in linear regulator controller, and only an external NPN transistor is needed to create a linear regulator. The output voltage of the linear regulator can be programmed between 4.75V and 7.5V by the resistor divider at VCCLFB pin. The regulator output powers the gate drivers and other circuits of the phase ICs along with circuits in the control IC, and the voltage is usually programmed to optimize the converter efficiency. The linear regulator can be compensated by a 4.7uF capacitor at the VCCL pin. As with any linear regulator, due to stability reasons, there is an upper limit to the maximum value of capacitor that can be used at this pin and it’s a function of the number of phases used in the multiphase architecture and their switching frequency. Figure 14 provides Bode plots for the linear regulator with 5 phases switching at 750 kHz. An external 5V can be connected to this pin to replace the linear regulator with appropriate selection of the VCCLFB resistor divider, and VCCLDRV resistor. While using an external VCCL its essential to adjust it such that VCCLFB is slightly higher than the 1.19V reference voltage. This condition ensures that the VCCLDRV pin doesn’t load the ROSC pin. The switching frequency, VSETPT, and OCSET are derived from the loading current of ROSC pin. Figure 14 - VCCL regulator stability with 5 phases and PHSOUT equals 750 kHz. Page 22 of 47 June 12, 2007 IR3500 VCCL Under Voltage Lockout (UVLO) The IR3500 has no under voltage lockout for converter input voltage (VCC), but monitors the VCCL voltage instead, which is used for the gate drivers of phase ICs and circuits in control IC and phase ICs. During power up, the fault latch will be reset if VCCL is above 94% of the voltage set by resistor divider at VCCLFB pin. If VCCL voltage drops below 86% of the set value, the fault latch will be set. VID Fault Codes VID codes of 0000000X and 1111111X for VR11, and 11111 for AMD 5-bit Opteron will set the fault latch and disable the error amplifier. A 1.3us delay is provided to prevent a fault condition from occurring during Dynamic VID changes. A VID FAULT condition is latched for VR 11 with boot voltage and can only be cleared by cycling power to VCCL. Voltage Regulator Ready (VRRDY) The VRRDY pin is an open-collector output and should be pulled up to a voltage source through a resistor. After soft start cycle is complete, the VRRDY remains high until the output voltage is within regulation and SS/DEL is above 3.92V. The VRRDY pin becomes low if the fault latch, over voltage latch, open sense line latch, or open daisy chain latch is set. A high level at the VRRDY pin indicates that the converter is in operation and has no fault, but does not ensure the output voltage is within the specification. Output voltage regulation within the design limits can logically be assured however, assuming no component failure in the system. Open Voltage Loop Detection The output voltage range of error amplifier is detected all the time to ensure the voltage loop is in regulation. If any fault condition forces the error amplifier output above VCCL-1.08V for 8 switching cycles, the fault latch is set. The fault latch can only be cleared by cycling power to VCCL. Load Current Indicator Output The VDRP pin voltage represents the average current of the converter plus the VDAC voltage. The load current information can be retrieved by a differential amplifier which subtracts the VDAC voltage from the VDRP voltage. Enable Input For Intel VID codes, pulling the ENABLE pin below 0.8V sets the Fault Latch and a voltage above 0.85V enables the soft start of the converter. For AMD VID codes, pulling the ENABLE pin below 1.14V sets the Fault Latch and a voltage above 1.2V enables the soft start of the converter. Thermal Monitoring (VRHOT) A resistor divider including a thermistor at the HOTSET pin sets the VRHOT threshold. The thermistor is usually placed at the temperature sensitive region of the converter, and is linearized by a series resistor. The IR3500 compares the HOTSET pin voltage with a reference voltage of 1.6V. The VRHOT pin is an open-collector output and should be pulled up to a voltage source through a resistor. If the thermal trip point is reached the VRHOT output drives low. The hysteresis of the VRHOT comparator is added to eliminate toggling of VRHOT output. Over Voltage Protection (OVP) The output over-voltage happens during normal operation if a high side MOSFET short occurs or if output voltage is out of regulation. The over-voltage protection comparator monitors Vo pin voltage. If Vo pin voltage exceeds VDAC by 130mV, as shown in Figure 14, IR3500 raises ROSC/OVP pin voltage to V(VCCL) - 1V, which sends over voltage signal to system. The ROSC/OVP pin can also be connected to a thyrister in a crowbar circuit, which pulls the converter input low in over voltage conditions. The over voltage condition also sets the over voltage fault latch, which pulls error amplifier output low to turn off the converter output. At the same time IIN pin (ISHARE of phase ICs) is pulled up to VCCL to communicate the over voltage condition to phase ICs, as shown in Figure 15. In each Page 23 of 47 June 12, 2007 IR3500 phase IC, the OVP circuit overrides the normal PWM operation and will fully turn-on the low side MOSFET within approximately 150ns. The low side MOSFET will remain on until ISHARE pin voltage drops below V(VCCL) 800mV, which signals the end of over voltage condition. An over voltage fault condition is latched in the IR3500 and can only be cleared by cycling power to the IR3500 VCCL. OUTPUT VOLTAGE (VO) OVP THRESHOLD 130mV VCCL-800 mV IIN (ISHARE) GATEH (PHASE IC) GATEL (PHASE IC) FAULT LATCH ERROR AMPLIFIER OUTPUT (EAOUT) VDAC NORMAL OPERATION OVP CONDITION AFTER OVP Figure 15 - Over-voltage protection during normal operation In the event of a high side MOSFET short before power up, the OVP flag is activated with as little supply voltage as possible, as shown in Figure 16. The VOSEN+ pin is compared against a fixed voltage of 1.73V (typical) for OVP conditions at power-up. The ROSC/OVP pin will be pulled higher than 1.6V with VCCLDRV voltage as low as 1.8V. An external MOSFET or comparator should be used to disable the silver box, activate a crowbar, or turn off the supply source. The 1.8V threshold is used to prevent false over-voltage triggering caused by pre-charging of output capacitors. Pre-charging of converter output voltage may trigger OVP. If the converter output is pre-charged above 1.73V as shown in Figure 17, ROSC/OVP pin voltage will be higher than 1.6V when VCCLDRV voltage reaches 1.8V. ROSC/OVP pin voltage will be VCCLDRV-1V and rise with VCCLDRV voltage until VCCL is above UVLO threshold, after which ROSC/OVP pin voltage will be VCCL-1V. The converter cannot start unless the over voltage condition stops and VCCL is cycled. If the converter output is pre-charged 130mV above VDAC but lower than 1.73V, as shown in Figure 17, the converter will soft start until SS/DEL voltage is above 3.92V (4.0V-0.08V). Then, over voltage comparator is activated and fault latch is set. Page 24 of 47 June 12, 2007 IR3500 12V VCCL+0.7V VCC VCCL+0.7V 12V VCCLDRV 1.8V OUTPUT VOLTAGE (VOSEN+) VCCL UVLO ROSC/OVP 1.6V Figure 16 - Over-voltage protection during power-up 12V VCCL+0.7V VCC VCCL+0.7V VCCLDRV 1.8V OUTPUT VOLTAGE (VOSEN+) 1.73V VCCL UVLO ROSC/OVP 1.6V Figure 17 - Over-voltage protection with pre-charging converter output Vo > 1.73V Page 25 of 47 June 12, 2007 IR3500 12V VCC VCCL+0.7V VCCL+0.7V VCCLDRV OUTPUT VOLTAGE (VOSEN+) 1.73V VID + 0.13V VCCL UVLO VCCL - 1V ROSC/OVP 0.6V 3.92V (4V-0.08V) SS/DEL Figure 18 - Over-voltage protection with pre-charging converter output VID + 0.13V <Vo < 1.73V During dynamic VID down, OVP may be triggered when output voltage can not follow VDAC voltage change at light load with large output capacitance. Therefore, over-voltage threshold is raised to 1.73V from VDAC+130mV whenever dynamic VID is detected and the difference between output voltage and VDAC is more than 50mV, as shown in Figure 19. The over-voltage threshold is changed back to VDAC+130mV if the difference is smaller than 50mV. The overall system must be considered when designing for OVP. In many cases the over-current protection of the AC-DC or DC-DC converter supplying the multiphase converter will be triggered and provide effective protection without damage as long as all PCB traces and components are sized to handle the worst-case maximum current. If this is not possible, a fuse can be added in the input supply to the multiphase converter. Open Remote Sense Line Protection The IR3500 checks for open remote sense lines every time it is enabled and will not power on if there is an open sense line fault. If either remote sense line VOSEN+ or VOSEN- or both are open, the output of the remote sense amplifier (VO) drops. The IR3500 monitors its VO pin voltage continuously during normal operation. If the VO voltage is lower than 200 mV, two separate pulse currents are applied to VOSEN+ and VOSEN- pins respectively to check if the sense lines are open. If VOSEN+ is open, a voltage higher than 90% of V(VCCL) will be present at VOSEN+ pin and the output of open line detect comparator will be high. If VOSEN- is open, a voltage higher than 700mV will be present at VOSEN- pin and the output of open-line-detect comparator will be high. The open sense line fault latch is set, which pulls the error amplifier output low immediately and shuts down the converter. The SS/DEL voltage is discharged and the fault latch can only be reset by cycling VCCL power. Page 26 of 47 June 12, 2007 IR3500 VID (FAST VDAC) VDAC OV THRESHOLD 1.73V VDAC + 130mV OUTPUT VOLTAGE (VO) VDAC 50mV 50mV NORMAL OPERATION VID DOWN LOW VID VID UP NORMAL OPERATION Figure 19 - Over-voltage protection during dynamic VID Open Daisy Chain Protection IR3500 checks the daisy chain every time it powers up. It starts a daisy chain pulse on the PHSOUT pin and detects the feedback at PHSIN pin. If no pulse comes back after 32 CLKOUT pulses, the pulse is restarted again. If the pulse fails to come back the second time, the open daisy chain fault is registered, and SS/DEL is not allowed to charge. The fault latch can only be reset by cycling the power to VCCL. After powering up, the IR3500 monitors PHSIN pin for a phase input pulse equal or less than the number of phases detected. If PHSIN pulse does not return within the number of phases in the converter, another pulse is started on PHSOUT pin. If the second started PHSOUT pulse does not return on PHSIN, an open daisy chain fault is registered. Phase Number Determination After a daisy chain pulse is started, the IR3500 checks the timing of the input pulse at PHSIN pin to determine the phase number. This information is used to have symmetrical phase delay between phase switching without the need of any external component. Single Phase Operation In an architecture where only a single phase is needed the switching frequency is determined by the clock frequency. Page 27 of 47 June 12, 2007 IR3500 APPLICATIONS INFORMATION FUSE CVCC1 Q1 12V ROVP1 RVCCLDRV RVCCLFB1 RVCCLFB2 CVCCL 4.7uF Q3 13 VC C 16 15 C SIN - EAIN GATEL PGN D C LKIN VOUT+ 9 DISTRIBUTION IMPEDANCE U12 COUT 8 5 VOUT SENSE+ CVCC2 13 VC C EAIN ISHARE LGND PHSIN RHOTSET2 5 CCP1 SW IR3505 PHASE IC DACIN GATEH BOOST GAT EL CCP CIN2 U21 VCCL 12 RCS2 CCS2 11 CBST2 L2 10 9 U22 8 4 RCP 15 16 1 C SIN - U20 C SIN + RDRP1 CDRP PGN D 17 14 RVSETPT 18 C LKIN 19 VOUT SENSECVDAC RVDAC ROCSET PH SOU T 21 7 22 20 2 CFB CCS1 L1 10 CVCCL1 ENABLE RFB1 VCCL RCS1 CBST1 CSS/DEL RDRP RFB BOOST 12 11 VOUTROSC 6 EAOU T VDRP 23 3 VRHOT PHSIN GATEH 24 16 FB IIN VO VSETPT VID1 VID0 LGND U11 SW IR3505 PHASE IC DACIN 25 C LKOU T 27 26 30 28 VC C L PH SIN VC C LF B VC C LD R V VR R D Y VID SEL PH SOU T OCSET VID2 VOSEN + VID0 8 VID3 VDAC 15 7 14 6 VID1 SS/DEL IR3500 CONTROL IC VID4 13 VID2 VID5 VOSEN - 5 H OT SET 4 VID3 LGND ROSC / OVP 12 3 VID4 VID6 9 VID5 VID7 VR H OT 2 EN ABLE VID6 11 1 10 VID7 31 4 29 VIDSEL 32 VR READY 3 CIN1 ISHARE PH SOU T 2 7 1 C SIN + U10 6 ROVP2 14 SCR Q2 RFB2 RHOTSET1 CVCCL2 13 16 15 EAIN C SIN - VC C GATEH GAT EL BOOST VCCL 12 RCS3 CCS3 11 CBST3 L3 10 9 U32 8 PGN D PHSIN C LKIN LGND 5 4 U31 SW IR3505 PHASE IC DACIN PH SOU T 3 CIN3 ISHARE 7 2 6 1 C SIN + U30 14 CVCC3 CVCCL3 RTHERM1 RTHERM2 CLOSE TO POWER STAGE Figure 20 - IR3500 / IR3505 Three Phase AMD Opteron Converter Page 28 of 47 June 12, 2007 IR3500 FUSE CVCC1 Q1 12V ROVP1 RVCCLDRV RVCCLFB1 RVCCLFB2 CVCCL 4.7uF Q3 14 16 13 VCC CSIN- EAIN GATEL PGND CLKIN VOUT+ DISTRIBUTION IMPEDANCE U12 COUT 8 5 VOUT SENSE+ 9 CVCC2 CCP VCC 13 ISHARE LGND PHSIN RHOTSET2 5 CCP1 SW IR3505 PHASE IC DACIN GATEH BOOST GATEL 4 RCP CIN2 U21 VCCL 12 RCS2 CCS2 11 CBST2 L2 10 9 U22 8 1 14 16 U20 EAIN RDRP1 CDRP CSIN- 17 15 RVSETPT 18 CSIN+ 19 VOUT SENSE- CVDAC RVDAC PGND 26 27 CCS1 L1 ROCSET CLKIN 20 PHSOUT 21 2 CFB RCS1 CBST1 10 CVCCL1 3 RFB1 VCCL 12 11 CSS/DEL RDRP RFB BOOST VOUTROSC 7 EAOUT VDRP 23 22 ENABLE VRHOT PHSIN GATEH 24 16 FB 15 14 VO IIN VOSEN+ VSETPT VID1 VOSEN- VID2 VID0 LGND U11 SW IR3505 PHASE IC DACIN 25 CLKOUT VCCL PHSIN 30 28 29 VCCLFB PHSOUT VDAC OCSET CIN1 ISHARE 6 VID3 13 8 IR3500 CONTROL IC VID4 12 VID0 VCCLDRV 7 SS/DEL HOTSET 6 VID1 VRRDY VID2 VIDSEL 5 ROSC / OVP VID5 VRHOT 4 VID3 LGND VID6 ENABLE VID4 VID7 9 3 11 2 VID5 10 1 VID6 31 VIDSEL 4 32 3 PHSOUT 2 7 1 VR READY CSIN+ U10 6 ROVP2 VID7 15 SCR Q2 RFB2 RHOTSET1 CVCCL2 VCC 13 16 EAIN 14 GATEH GATEL BOOST VCCL 12 RCS3 CCS3 11 CBST3 L3 10 9 U32 8 PGND PHSIN CLKIN LGND U31 SW IR3505 PHASE IC DACIN 5 4 CIN3 ISHARE PHSOUT 3 7 2 6 1 CSIN- U30 CSIN+ 15 CVCC3 CVCCL3 VCC 13 16 EAIN 14 GATEH GATEL BOOST VCCL 12 RCS4 CCS4 11 CBST4 L4 10 9 U42 8 PGND PHSIN CLKIN LGND U41 SW IR3505 PHASE IC DACIN 5 4 CIN4 ISHARE PHSOUT 3 7 2 6 1 CSIN- U40 CSIN+ 15 CVCC4 CVCCL4 VCC 13 16 EAIN 14 GATEH GATEL BOOST VCCL 12 RCS5 CCS5 11 CBST5 L5 10 9 U52 8 PGND PHSIN CLKIN LGND U51 SW IR3505 PHASE IC DACIN 5 4 CIN5 ISHARE PHSOUT 3 7 2 6 1 CSIN- U50 CSIN+ 15 CVCC5 CVCCL5 VCC 13 16 EAIN 14 GATEH GATEL BOOST VCCL 12 RCS6 CCS6 11 CBST6 L6 10 9 U62 8 PGND PHSIN CLKIN LGND U61 SW IR3505 PHASE IC DACIN 5 4 CIN6 ISHARE PHSOUT 3 7 2 6 1 CSIN- U60 CSIN+ 15 CVCC6 CVCCL6 RTHERM1 RTHERM2 CLOSE TO POWER STAGE Figure 21 - IR3500 / IR3505 Six Phase VRM11.0 / VRD11.0 / EVRD11.0 Converter Page 29 of 47 June 12, 2007 IR3500 DESIGN PROCEDURE Oscillator Resistor Rosc The oscillator of IR500 generates square-wave pulses to synchronize the phase ICs. The switching frequency of each phase converter equals the PHSOUT frequency, which is set by the external resistor ROSC according to the curve in Figure 23. The CLKOUT frequency equals the switching frequency multiplied by the phase number. The Rosc sets the reference current used for the no load offset and OCSET which is given by Figure 23 and equals: ISETPT = IOCSET = 0.595 Rosc (1) Soft Start Capacitor CSS/DEL The soft start capacitor CSS/DEL programs five different time parameters. They include soft start delay time, soft start time, VID sample delay time, VR ready delay time and over-current fault latch delay time after VR ready. For the converter using VR11 VID with boot voltage, the SS/DEL pin voltage controls the slew rate of the converter output voltage, as shown in Figure 10. After the ENABLE pin voltage rises above 0.85V, there is a softstart delay time TD1, after which the error amplifier output is released to allow the soft start of output voltage. The soft start time TD2 represents the time during which converter voltage rises from zero to 1.1V. The VID sample delay time (TD3) is the time period when VID stays at boot voltage of 1.1V. VID rise or fall time (TD4) is the time when VID changes from boot voltage to the final voltage. The VR ready delay time (TD5) is the time period from VR reaching the final voltage to the VR ready signal being issued, which is determined by the delay comparator threshold. CSS/DEL = 0.1uF meets all the specifications of TD1 to TD5, which are determined by (2) to (6) respectively. TD1 = C SS / DEL *1.4 C SS / DEL *1.4 = I CHG 52.5 *10 −6 (2) TD 2 = C SS / DEL *1.1 C SS / DEL *1.1 = I CHG 52.5 *10 −6 (3) TD3 = TD 4 = C SS / DEL * (3 − 1.4 − 1.1) C SS / DEL * 0.7 = I CHG 52.5 * 10 −6 C SS / DEL * V DAC − 1.1 TD5 = I CHG = C SS / DEL * V DAC − 1.1 52.5 *10 −6 C SS / DEL * (3.92 − 3) C * 0.92 − TD4 = SS / DEL −6 − TD4 I CHG 52.5 * 10 (4) (5) (6) For the converter using VR 11 VID without boot voltage or AMD 5-bit and 6-bit VIDs, the SS/DEL pin voltage controls the slew rate of the converter output voltage, as shown in Figure 11. After the ENABLE pin voltage rises above 0.85V/1.2V, there is a soft-start delay time TD1, after which the error amplifier output is released to allow the soft start. The soft start time TD2 represents the time during which converter voltage rises from zero to Vo. VR ready delay time (TD3) is the time period from VR reaching the final voltage to the VR ready signal being issued. Calculate CSS/DEL based on the required soft start time (TD2). CSS / DEL = Page 30 of 47 TD 2 * I CHG TD 2 * 52.5 *10 −6 = VO VO (7) June 12, 2007 IR3500 The soft start delay time (TD1) and VR ready delay time (TD3) are determined by (8) to (9) respectively. C *1.4 CSS / DEL *1.4 (8) TD1 = SS / DEL = I CHG 52.5 *10− 6 TD3 = C SS / DEL * ( 4.0 − VO ) C SS / DEL * ( 4.0 − VO ) = I CHG 52.5 *10 − 6 (9) Once CSS/DEL is chosen, the minimum over-current fault latch delay time tOCDEL is fixed and can be quantified as t OCDEL = C SS / DEL * 0.12 C SS / DEL * 0.12 = I DISCHG 55 * 10 −6 (10) VDAC Slew Rate Programming Capacitor CVDAC and Resistor RVDAC The slew rate of VDAC down-slope SRDOWN can be programmed by the external capacitor CVDAC as defined in (11), where ISINK is the sink current of VDAC pin. The slew rate of VDAC up-slope is the same as that of downslope. The resistor RVDAC is used to compensate VDAC circuit and can be calculated as follows CVDAC = I SINK 44 *10 −6 = SR DOWN SR DOWN RVDAC = 0.5 + 3.2 ∗ 10 −15 CVDAC 2 (11) (12) Over Current Setting Resistor ROCSET The inductor DC resistance is utilized to sense the inductor current. The copper wire of inductor has a constant temperature coefficient of 3850 ppm/°C, and therefore the maximum inductor DCR can be calculated from (13), where RL_MAX and RL_ROOM are the inductor DCR at maximum temperature TL_MAX and room temperature T_ROOM respectively. R L _ MAX = R L _ ROOM ∗ [1 + 3850 * 10 −6 ∗ (TL _ MAX − TROOM )] (13) The total input offset voltage (VCS_TOFST) of current sense amplifier in phase ICs is the sum of input offset (VCS_OFST) of the amplifier itself and that created by the amplifier input bias current flowing through the current sense resistor RCS. VCS _ TOFST = VCS _ OFST + I CSIN + ∗ RCS (14) The over-current limit is set by the external resistor ROCSET and is given by (15). In a multiphase architecture the peak to peak ripple of the net inductor current is much smaller than the stand alone phase due to interleaving. The ratio of the peak to average current in this case can be approximated using (16). ROCSET = [ I LIMIT ∗ RL _ MAX ∗ (1 + K P ) + VCS _ TOFST ] ∗ GCS / I OCSET n m m +1 VI ⋅ D ⋅ (1 − D) ⋅ n ⋅ ( D − n ) ⋅ ( n − D) KP = (I LIMIT / n) ⋅ L ⋅ f sw ⋅ 2 ⋅ D ⋅ (1 − D) (15) (16) Where; ILIMIT=Over current limit, n=Number of phases, KP=Ratio of the peak to average current for the inductor, GCS=Gain of the current sense amplifier, IOCSET= Determined by the ROSC and given by Figure 24, D=Vo/VI, m=Maximum integer that doesn’t exceed (n*D) Page 31 of 47 June 12, 2007 IR3500 No Load Output Voltage Setting Resistor RVSETPT, A resistor between VSETPT pin and VDAC is used to create output voltage offset VO_NLOFST, which is the difference between VDAC voltage and output voltage at no load condition. RVSETPT is determined by (17), where IVSETPT is the current flowing out of VSETPT pin as shown in Figure 23. RVSETPT = VO _ NLOFST (17) IVSETPT VCCL Capacitor CVCCL The capacitor is selected based on the stability requirement of the linear regulator and the load current to be driven. The linear regulator supplies the bias and gate drive current of the phase ICs. A 4.7uF normally ensures stable VCCL performance for Intel VR11 and AMD applications. VCCL Programming Resistor RVCCLFB1 and RVCCLFB2 Since VCCL voltage is proportional to the MOSFET gate driver loss and inversely proportional to the MOSFET conduction loss, the optimum voltage should be chosen to maximize the converter efficiency. VCCL linear regulator consists of an external NPN transistor, a ceramic capacitor and a programmable resistor divider. Pre-select RVCCLFB1, and calculate RVCCLFB2 from (18). RVCCLFB 2 = RVCCLFB1 *1.19 VCCL − 1.19 (18) VCCL Regulator Drive Resistor RVCCLDRV The drive resistor is primarily dependent on the load current requirement of the linear regulator and the minimum input voltage requirements. The following equation gives an estimate of the average load current of the switching phase ICs. [ ] I drive _ avg = (Q gb + Q gt ) ⋅ f sw + 10 mA ⋅ n (19) Qgb and Qgt are the gate charge of the top and bottom FET. For a minimum input voltage and a maximum VCCL, the maximum RVCCLDRV required to use the full pull-down current of the VCCL driver is given by RVCCLDRV = V I (min) − 0.7 − VCCL(max) I drive _ avg / β min (20) Due to limited pull down capability of the VCCLDRV pin, make sure the following condition is satisfied. VI (max) − 0.7 − VCCL (min) < 10mA RVCCLDRV (21) In the above equation, VI( min) and VI( max) is the minimum and maximum anticipated input voltage. If the above condition is not satisfied there is a need to use a device with higher βmin or Darlington configuration can be used instead of a single NPN transistor. Thermistor RTHERM and Over Temperature Setting Resistors RHOTSET1 and RHOTSET2 The threshold voltage of VRHOT comparator is fixed at 1.6V, and a negative temperature coefficient (NTC) thermistor RTHERM is required to sense the temperature of the power stage. If we pre-select RTHERM, the NTC thermistor resistance at allowed maximum temperature TMAX is calculated from (22). Page 32 of 47 June 12, 2007 IR3500 RTMAX = RTHERM * EXP[ BTHERM * ( 1 T L _ MAX − 1 T _ ROOM (22) )] Select the series resistor RHOTSET2 to linearize the NTC thermistor, which has non-linear characteristics in the operational temperature range. Then calculate RHOTSET1 corresponding to the allowed maximum temperature TMAX from (23). R HOTSET 1 = ( RTMAX + R HOTSET 2 ) * (VCCL − 1.6) 1.6 (23) VOLTAGE LOOP COMPENSATION The adaptive voltage positioning (AVP) is usually adopted in the computer applications to improve the transient response and reduce the power loss at heavy load. Like current mode control, the adaptive voltage positioning loop introduces an extra zero to the voltage loop and splits the double poles of the power stage, which makes the voltage loop compensation much easier. Adaptive voltage positioning lowers the converter voltage by RO*IO, where RO is the required output impedance of the converter. Pre-select feedback resistor RFB, and calculate the droop resistor RDRP, RDRP = RFB ∗ RL _ MAX * GCS (25) n ∗ RO The selection of compensation types depends on the output capacitors used in the converter. For applications using Electrolytic, Polymer or AL-Polymer capacitors and running at lower frequency, type II compensation shown in Figure 22(a) is usually enough. While for the applications using only ceramic capacitors and running at higher frequency, type III compensation shown in Figure 22(b) is preferred. For applications where AVP is not required, the compensation is the same as for the regular voltage mode control. For converters using Polymer, AL-Polymer, and ceramic capacitors, which have much higher ESR zero frequency, type III compensation is required as shown in Figure 22(b) with RDRP and CDRP removed. CCP1 CCP1 RFB RCP CCP VO+ RCP CCP RFB1 CFB FB - RFB VO+ FB EAOUT - RDRP EAOUT RDRP VDRP VDAC + (a) Type II compensation EAOUT VDAC VDRP EAOUT + CDRP (b) Type III compensation Figure 22 - Voltage loop compensation network Type II Compensation for AVP Applications Determine the compensation at no load, the worst case condition. Choose the crossover frequency fc between 1/10 and 1/5 of the switching frequency per phase. Assume the time constant of the resistor and capacitor across the output inductors matches that of the inductor, and determine RCP and CCP from (26) and (27), where LE and CE are the equivalent inductance of output inductors and the equivalent capacitance of output capacitors respectively. Page 33 of 47 June 12, 2007 IR3500 (2π ∗ fC ) 2 ∗ LE ∗ CE ∗ RFB ∗ 5 RCP = (26) VI * 1 + ( 2π * fC * C * RC ) 2 10 ∗ LE ∗ C E CCP = (27) RCP CCP1 is optional and may be needed in some applications to reduce the jitter caused by the high frequency noise. A ceramic capacitor between 10pF and 220pF is usually enough. Type III Compensation for AVP Applications Determine the compensation at no load, the worst case condition. Assume the time constant of the resistor and capacitor across the output inductors matches that of the inductor, the crossover frequency and phase margin of the voltage loop can be estimated by (28) and (29), where RLE is the equivalent resistance of inductor DCR. f C1 = RDRP 2π * CE ∗ GCS * RFB ∗ RLE θ C1 = 90 − A tan(0.5) ∗ (28) 180 (29) π Choose the desired crossover frequency fc around fc1 estimated by (28) or choose fc between 1/10 and 1/5 of the switching frequency per phase, and select the components to ensure the slope of close loop gain is -20dB per decade around the crossover frequency. Choose resistor RFB1 according to (30), and determine CFB and CDRP from (31) and (32). 1 R FB 2 R FB1 = CFB = to R FB1 = 2 R FB 3 1 4π ∗ fC ∗ RFB1 C DRP = ( R FB + R FB1 ) ∗ C FB R DRP (30) (31) (32) RCP and CCP have limited effect on the crossover frequency, and are used only to fine tune the crossover frequency and transient load response. Determine RCP and CCP from (33) and (34). RCP = CCP = (2π ∗ fC ) 2 ∗ LE ∗ CE ∗ RFB ∗ 5 VI 10 ∗ LE ∗ C E RCP (33) (34) CCP1 is optional and may be needed in some applications to reduce the jitter caused by the high frequency noise. A ceramic capacitor between 10pF and 220pF is usually enough. Type III Compensation for Non-AVP Applications Resistor RDRP and capacitor CDRP are not needed. Choose the crossover frequency fc between 1/10 and 1/5 of the switching frequency per phase and select the desired phase margin θc. Calculate K factor from (35), and determine the component values based on (36) to (40), π θ K = tan[ ∗ ( C + 1.5)] 4 180 Page 34 of 47 (35) June 12, 2007 IR3500 RCP = RFB ∗ ( 2π ∗ LE ∗ CE ∗ fC ) 2 ∗ 5 VI ∗ K (36) CCP = K 2π ∗ fC ∗ RCP (37) CCP1 = 1 2π ∗ fC ∗ K ∗ RCP (38) CFB = K 2π ∗ fC ∗ RFB (39) R FB1 = 1 2π ∗ f C ∗ K ∗ C FB (40) DESIGN EXAMPLE 1 – AMD OPTERON CONVERTER (FIGURE 20) SPECIFICATIONS Input Voltage: VI=12 V DAC Voltage: VDAC=1.3 V No Load Output Voltage Offset: VO_NLOFST=10 mV Output Current: IO=120 ADC Maximum Output Current: IOMAX=135 ADC Output Impedance: RO=0.7 mΩ Soft Start Delay Time: TD1=1-5mS Soft Start Time: TD2=2 mS VR Ready Delay Time: TD3=0-10mS Maximum Over Current Delay: tOCDEL<2.5mS Dynamic VID Down-Slope Slew Rate: SRDOWN=2.5mV/uS Over Temperature Threshold: TMAX=115 ºC POWER STAGE Phase Number: n=3 Switching Frequency: fSW =250 kHz Output Inductors: L=470 nH, RL= 1mΩ Output Capacitors: Polymer, C=560uF, RC= 7mΩ, Number Cn=12 IR3500 EXTERNAL COMPONENTS Oscillator Resistor Rosc Once the switching frequency is chosen, ROSC can be determined from the curve in Figure 23. For a switching frequency of 250kHz per phase, choose ROSC=50kΩ. The reference current for VSETPT and OCSET is given by 11.9 uA. Soft Start Capacitor CSS/DEL Determine the soft start capacitor from the required soft start time. CSS / DEL = TD 2 * I CHG 2 *10−3 * 52.5 *10−6 = = 0.1uF VO 1.3 Page 35 of 47 June 12, 2007 IR3500 The soft start delay time is TD1 = C SS / DEL *1.4 0.1*10 −6 *1.4 = = 2.67 mS I CHG 52.5 *10 −6 The VR ready delay time is TD3 = C SS / DEL * ( 4.0 − VO ) 0.1*10 −6 * ( 4.0 − 1.3) = = 5.14mS I CHG 52.5 *10 −6 The minimum over current fault latch delay time is t OCDEL = C SS / DEL * 0.12 0.1 * 10 −6 * 0.12 = = 0.2ms I DISCHG 55 * 10 −6 VDAC Slew Rate Programming Capacitor CVDAC and Resistor RVDAC Calculate the VDAC down-slope slew-rate programming capacitor from the required down-slope slew rate. The up-slope slew rate is the same as the down-slope slew rate. CVDAC = I SINK 44 *10 −6 = = 18nF SR DOWN 2.5 *10 −3 / 10 −6 Calculate the programming resistor. RVDAC = 0.5 + 3.2 *10−15 CVDAC 2 = 0.5 + 3.2 *10−15 = 10Ω (18 *10−9 )2 Over Current Setting Resistor ROCSET The room temperature is 25ºC and the target PCB temperature is 100 ºC. The phase IC die temperature is about 1 ºC higher than that of phase IC, and the inductor temperature is close to PCB temperature. Calculate Inductor DC resistance at 100 ºC, RL _ MAX = RL _ ROOM ∗ [1 + 3850*10−6 ∗ (TL _ MAX − TROOM )] = 1*10−3 ∗ [1 + 3850*10−6 ∗ (100 − 25)] = 1.29mΩ Set the over current limit at 135A. From Figure 24, the bias current of OCSET pin (IOCSET) is 11.9uA with ROSC=50kΩ. The total current sense amplifier input offset voltage is 0.3mV, which includes the offset created by the current sense amplifier (CSA) input bias current through the resistor RCS. VCS _ TOFST = 0.3mV Calculate constant KP, the ratio of inductor peak current over average current in each phase, m m +1 VI ⋅ D ⋅ (1 − D) ⋅ n ⋅ ( D − n ) ⋅ ( n − D) = KP = (I LIMIT / n ) ⋅ L ⋅ f sw ⋅ 2 ⋅ D ⋅ (1 − D) 0 0 +1 12 ⋅ 0.108 ⋅ (1 − 0.108) ⋅ 3 ⋅ (0.108 − 3 ) ⋅ ( 3 − 0.108) = 0.082 (135 / 3) ⋅ 0.47u ⋅ 250k ⋅ 2 ⋅ 0.108 ⋅ (1 − 0.108) I LIMIT ∗ RL _ MAX ∗ (1 + K P ) + VCS _ TOFST ] ∗ GCS / I OCSET n 135 =( ∗ 1.29 * 10 −3 ∗ 1.082 + 0.3 * 10 −3 ) ∗ 34 /(11.9 * 10 − 6 ) = 181kΩ 3 ROCSET = [ Page 36 of 47 June 12, 2007 IR3500 No Load Output Voltage Setting Resistor RVSETPT and Adaptive Voltage Positioning Resistor RDRP From Figure 24, the bias current of VSETPT pin is 11.9uA with ROSC=50kΩ. V CS _ TOFST RVSETPT = I VSETPT = 10 * 10 −3 = 840 Ω , choose RVSETPT=825Ω. 11 .9 * 10 − 6 VCCL Programming Resistor RVCCLFB1 and RVCCLFB2 Choose VCCL=7V to maximize the converter efficiency. Pre-select RVCCLFB1=20kΩ, and calculate RVCCLFB2. RVCCLFB 2 = RVCCLFB 1 *1.19 20 *103 *1.19 = = 4.05kΩ VCCL − 1.19 7 − 1.19 VCCL Drive Resistor RVCCLDRV The maximum drive current for the linear regulator is dependent on the type of MosFET used. For this example its assumed that IR6622/ IRF6691 are used as buck switches. I drive _ avg = [( 47 n + 11n ) ⋅ 250 k + 10 mA ] ⋅ 3 = 75 mA (19) The minimum input voltage is assumed to be 10 V and VCCL is fixed at 6.5V for this design. RVCCLDRV = 10V − 0.7V − 6.5V = 1.8kΩ 75mA / 50 (20) Assuming the maximum input voltage to as 14 V, 14V − 0.7 − 6.5 = 3mA < 10mA 1 .8 k Ω (21) Thermistor RTHERM and Over Temperature Setting Resistors RHOTSET1 and RHOTSET2 Choose NTC thermistor RTHERM=2.2kΩ, which has a constant of BTHERM=3520, and the NTC thermistor resistance at the allowed maximum temperature TMAX is, RTMAX = RTHERM * EXP[ BTHERM * ( 1 T L _ MAX − 1 T _ ROOM )] = 2.2 *10 3 * EXP[3520 * ( 1 1 − )] = 142Ω 273 + 115 273 + 25 Select RHOTSET2 = 931Ω to linearize the NTC, which has non-linear characteristics in the operational temperature range. Then calculate RHOTSET1 corresponding to the allowed maximum temperature TMAX. R HOTSET 1 = ( RTMAX + R HOTSET 2 ) * (VCCL − 1.6) (142 + 931) * (7 − 1.6) = = 3.63kΩ , 1 .6 1.6 choose RHOTSET1=3.65kΩ. VOLTAGE LOOP COMPENSATION Type II compensation is used for the converter with Polymer output capacitors. Choose the crossover frequency fc=25kHz, which is 1/10 of the switching frequency per phase, and determine Rcp and CCP. Pre-select RFB=2.00kΩ, and calculate RDRP, RCP and CCP. Page 37 of 47 June 12, 2007 IR3500 R DRP = RCP = CCP = R FB ∗ R L _ MAX * GCS n ∗ RO 2000 * 1.29 * 10 −3 * 34 = = 41.8kΩ , choose RDRP=42.2kΩ 3 * 0.7 * 10 −3 (2π ∗ fC )2 ∗ LE ∗ CE ∗ RFB ∗ 5 VI * 1 + (2π * fC * C * RC )2 10 ∗ LE ∗ CE = = (2π ∗ 25 ∗103 )2 ∗ (470 ∗10−9 / 3) ∗ (560 ∗10−6 ∗12) ∗ 2000 ∗ 5 12 * 1 + (2π * 25 *103 * 560 *10−6 * 7 *10−3 )2 10 ∗ (470 ∗ 10−9 / 3) ∗ (560 ∗ 10 −6 *12) RCP 21.5 ∗103 Choose CCP1=47pF to reduce high frequency noise. = 21.5kΩ , = 15nF DESIGN EXAMPLE 2 – VR11 HIGH FREQUENCY ALL-CERAMIC CONVERTER (FIG. 21) SPECIFICATIONS Input Voltage: VI=12 V DAC Voltage: VDAC=1.3 V No Load Output Voltage Offset: VO_NLOFST=20 mV Output Current: IO=105 ADC Maximum Output Current: IOMAX=120 ADC Output Impedance: RO=0.91 mΩ Soft Start Delay Time: TD1=1-5mS Soft Start Time: TD2=0-3mS VID Sample Delay Time: TD3=0.05-3mS VID Rise Time: TD4=0-2.5mS VR Ready Delay Time: TD5=0-3mS Maximum Over Current Delay Time: tOCDEL<2.5mS Dynamic VID Down-Slope Slew Rate: SRDOWN=2.5mV/uS Over Temperature Threshold: TMAX=115 ºC POWER STAGE Phase Number: n=6 Switching Frequency: fSW = 800 kHz Output Inductors: L=100 nH, RL=0.5 mΩ Output Capacitors: Ceramic, C=22uF, RC= 2mΩ, Number Cn=62 IR3500 EXTERNAL COMPONENTS Oscillator Resistor Rosc Once the switching frequency is chosen, ROSC can be determined from the curve in Figure 23 data sheet. For a switching frequency of 800kHz per phase, choose ROSC = 15.0 kΩ. The reference current is given by 40uA. Soft Start Capacitor CSS/DEL Determine the soft start capacitor to meet the specifications of the delay time. Choose CSS/DEL=0.1uF. The soft start delay time is TD1 = C SS / DEL * 1.4 0.1 * 10 −6 * 1.4 = = 2.67mS I CHG 52.5 * 10 −6 Page 38 of 47 June 12, 2007 IR3500 The soft start time is TD 2 = C SS / DEL *1.1 0.1*10 −6 *1.1 = = 2.1mS I CHG 52.5 *10 − 6 The VID sample delay time is TD3 = C SS / DEL * (3.2 − 1.4 − 1.1) 0.1*10 −6 * 0.7 = = 1.33mS I CHG 52.5 *10 − 6 VID rise time is TD 4 = C SS / DEL * V DAC − 1.1 I CHG = 0.1*10 −6 * 1.3 − 1.1 52.5 *10 −6 = 0.38mS The VR ready delay time is TD5 = C SS / DEL * (3.92 − 3) 0.1 * 10 −6 * 0.92 − TD 4 = − TD 4 = 1.37 mS I CHG 52.5 * 10 −6 Minimum over current fault latch delay time is t OCDEL = C SS / DEL * 0.12 0.1 * 10 −6 * 0.12 = = 0.21ms I OCDISCHG 55 * 10 −6 VDAC Slew Rate Programming Capacitor CVDAC and Resistor RVDAC Calculate the VDAC down-slope slew-rate programming capacitor from the required down-slope slew rate. The up-slope slew rate is the same as the down-slope slew rate. CVDAC = I SINK 44 *10 −6 = = 18nF SR DOWN 2.5 *10 −3 / 10 −6 Calculate the programming resistor. RVDAC = 0.5 + 3.2 *10−15 CVDAC 2 = 0.5 + 3.2 *10−15 (18 *10−9 ) 2 = 10Ω Over Current Setting Resistor ROCSET The room temperature is 25ºC and the target PCB temperature is 100 ºC. The phase IC die temperature is about 1 ºC higher than that of phase IC, and the inductor temperature is close to PCB temperature. Calculate Inductor DC resistance at 100 ºC, RL _ MAX = RL _ ROOM ∗ [1 + 3850*10−6 ∗ (TL _ MAX − TROOM )] = 0.5 *10−3 ∗ [1 + 3850*10−6 ∗ (100 − 25)] = 0.64mΩ Set the over current limit at 135A. From Figure 22, the bias current of OCSET pin (IOCSET) is 40uA with ROSC=15kΩ. The total current sense amplifier input offset voltage is 0.3mV, which includes the offset created by the current sense amplifier (CSA) input bias current through the resistor RCS. VCS _ TOFST = 0.3mV Page 39 of 47 June 12, 2007 IR3500 Calculate constant KP, the ratio of inductor peak current over average current in each phase, m m +1 VI ⋅ D ⋅ (1 − D) ⋅ n ⋅ ( D − n ) ⋅ ( n − D) = KP = (I LIMIT / n ) ⋅ L ⋅ f sw ⋅ 2 ⋅ D ⋅ (1 − D) ROCSET = [ =( 0 0 +1 12 ⋅ 0.108 ⋅ (1 − 0.108) ⋅ 6 ⋅ (0.108 − 6 ) ⋅ ( 6 − 0.108) = 0.126 (135 / 6) ⋅ 0.1u ⋅ 800k ⋅ 2 ⋅ 0.108 ⋅ (1 − 0.108) I LIMIT ∗ RL _ MAX ∗ (1 + K P ) + VCS _ TOFST ] ∗ GCS / I OCSET n 135 ∗ 0.64 * 10 − 3 ∗ 1.126 + 0.3 * 10 − 3 ) ∗ 34 /( 40 * 10 − 6 ) = 14 kΩ 6 Calculate constant KP, the ratio of inductor peak current over average current in each phase, No Load Output Voltage Setting Resistor RVSETPT and Adaptive Voltage Positioning Resistor RDRP From Figure 24, the bias current of VSETPT pin is 40uA with ROSC=15kΩ. RVSETPT = VO _ NLOFST I VSETPT = 20 * 10 −3 = 500Ω 40 * 10 −6 VCCL Programming Resistor RVCCLFB1 and RVCCLFB2 Choose VCCL=7V to maximize the converter efficiency. Pre-select RVCCLFB1=20kΩ, and calculate RVCCLFB2. RVCCLFB 2 = RVCCLFB1 *1.19 20 *103 *1.19 = = 4.05kΩ VCCL − 1.19 7 − 1.19 VCCL Drive Resistor RVCCLDRV The maximum drive current for the linear regulator is dependent on the type of MosFET used. For this example, it’s assumed that IR6622/ IRF6691 are used as buck switches. I drive _ avg = [( 47 n + 11n ) ⋅ 800 k + 10 mA ] ⋅ 6 = 350 mA (19) The minimum input voltage is assumed to be 10.5 V and VCCL is fixed at 6.5V for this design. RVCCLDRV = 10.5V − 0.7V − 6.5V = 660Ω 350mA / 70 (20) Choose a transistor with β(min) of 70. The maximum input voltage is assumed 13.5 V, 13.5V − 0.7 − 6.5 = 9.5mA < 10mA 660Ω (21) Thermistor RTHERM and Over Temperature Setting Resistors RHOTSET1 and RHOTSET2 Choose NTC thermistor RTHERM=2.2kΩ, which has a constant of BTHERM=3520, and the NTC thermistor resistance at the allowed maximum temperature TMAX is, RTMAX = RTHERM * EXP[ BTHERM * ( 1 1 1 1 − )] = 2.2 *10 3 * EXP[3520 * ( − )] = 142Ω T L _ MAX T _ ROOM 273 + 115 273 + 25 Select RHOTSET2 = 931Ω to linearize the NTC, which has non-linear characteristics in the operational temperature range. Then calculate RHOTSET1 corresponding to the allowed maximum temperature TMAX. Page 40 of 47 June 12, 2007 IR3500 R HOTSET 1 = ( RTMAX + R HOTSET 2 ) * (VCCL − 1.6) (142 + 931) * (7 − 1.6) = = 3.63kΩ , choose RHOTSET1=3.65kΩ. 1.6 1.6 VOLTAGE LOOP COMPENSATION Type III compensation is used for the converter with only ceramic output capacitors. The crossover frequency and phase margin of the voltage loop can be estimated as follows. Choose RFB = 1.65kΩ, and calculate RDRP. RDRP = RFB ∗ RL _ MAX * GCS n ∗ RO = 1.65 *103 * 0.64 *10−3 * 34 = 6.58kΩ , choose RDRP=6.65kΩ. 6 * 0.91 *10 −3 R DRP 6.65 *10 3 = = 165 kHz 2π ∗ C E ∗ G CS ∗ R FB ∗ R LE 2π ∗ ( 62 ∗ 22 * 10 − 6 ) ∗ 34 ∗ 1.65 *10 3 ∗ ( 0.5 * 10 − 3 / 6) f C1 = θC1 = 90 − A tan(0.5) ∗ Choose RFB1 = 180 π = 63° 2 2 ∗ RFB = ∗ 1.65 *103 = 1.10kΩ 3 3 Choose the desired crossover frequency fc (=150kHz) around fc1 estimated above, and calculate 1 CFB = 4π ∗ fC ∗ RFB1 CDRP = RCP = = 1 = 4.8nF , choose CFB=4.7nF. 4π ∗ 150 *103 ∗ 1.1 *103 ( RFB + RFB1 ) ∗ CFB (1.65 *103 + 1.1 *103 ) ∗ 4.7 *10−9 = = 2.0nF RDRP 6.65 *103 , choose CDRP=2.2nF. ( 2π ∗ fC ) 2 ∗ LE ∗ CE ∗ RFB ∗ 5 ( 2π ∗150 *103 ) 2 ∗ (100 *10−9 / 6) ∗ ( 22 *10−6 ∗ 62) ∗ 1.65 *103 * 5 = = 13.9kΩ VI 12 Choose RFB=13.7kΩ. CCP = 10 ∗ LE ∗ CE RCP = 10 ∗ (100 *10−9 / 6) ∗ (22 *10 −6 * 62) 13.7 ∗ 103 = 3.5nF , choose CCP=3.3nF. Choose CCP1=47pF to reduce high frequency noise. Page 41 of 47 June 12, 2007 IR3500 Figure 23 - Frequency variation with ROSC. Figure 24 - ISETPT, OCSET with ROSC. Page 42 of 47 June 12, 2007 IR3500 LAYOUT GUIDELINES The following layout guidelines are recommended to reduce the parasitic inductance and resistance of the PCB layout, therefore minimizing the noise coupled to the IC. • • • • • • • • Dedicate at least one middle layer for a ground plane LGND. Connect the ground tab under the control IC to LGND plane through a via. Place VCCL decoupling capacitor VCCL as close as possible to VCCL and LGND pins. Place the following critical components on the same layer as control IC and position them as close as possible to the respective pins, ROSC, ROCSET, RVDAC, CVDAC, and CSS/DEL. Avoid using any via for the connection. Place the compensation components on the same layer as control IC and position them as close as possible to EAOUT, FB, VO and VDRP pins. Avoid using any via for the connection. Use Kelvin connections for the remote voltage sense signals, VOSNS+ and VOSNS-, and avoid crossing over the fast transition nodes, i.e. switching nodes, gate drive signals and bootstrap nodes. Avoid analog control bus signals, VDAC, IIN, and especially EAOUT, crossing over the fast transition nodes. Separate digital bus, CLKOUT, PHSOUT and PHSIN from the analog control bus and other compensation components. Page 43 of 47 June 12, 2007 IR3500 PCB Metal and Component Placement • Lead land width should be equal to nominal part lead width. The minimum lead to lead spacing should be ≥ 0.2mm to minimize shorting. • Lead land length should be equal to maximum part lead length + 0.3 mm outboard extension + 0.05mm inboard extension. The outboard extension ensures a large and inspectable toe fillet, and the inboard extension will accommodate any part misalignment and ensure a fillet. • Center pad land length and width should be equal to maximum part pad length and width. However, the minimum metal to metal spacing should be ≥ 0.17mm for 2 oz. Copper (≥ 0.1mm for 1 oz. Copper and ≥ 0.23mm for 3 oz. Copper) • A single 0.30mm diameter via shall be placed in the center of the pad land and connected to ground to minimize the noise effect on the IC. Page 44 of 47 June 12, 2007 IR3500 Solder Resist • The solder resist should be pulled away from the metal lead lands by a minimum of 0.06mm. The solder resist mis-alignment is a maximum of 0.05mm and it is recommended that the lead lands are all Non Solder Mask Defined (NSMD). Therefore pulling the S/R 0.06mm will always ensure NSMD pads. • The minimum solder resist width is 0.13mm. • At the inside corner of the solder resist where the lead land groups meet, it is recommended to provide a fillet so a solder resist width of ≥ 0.17mm remains. • The land pad should be Solder Mask Defined (SMD), with a minimum overlap of the solder resist onto the copper of 0.06mm to accommodate solder resist mis-alignment. In 0.5mm pitch cases it is allowable to have the solder resist opening for the land pad to be smaller than the part pad. • Ensure that the solder resist in-between the lead lands and the pad land is ≥ 0.15mm due to the high aspect ratio of the solder resist strip separating the lead lands from the pad land. • The single via in the land pad should be tented or plugged from bottom board side with solder resist. Page 45 of 47 June 12, 2007 IR3500 Stencil Design • The stencil apertures for the lead lands should be approximately 80% of the area of the lead lands. Reducing the amount of solder deposited will minimize the occurrence of lead shorts. Since for 0.5mm pitch devices the leads are only 0.25mm wide, the stencil apertures should not be made narrower; openings in stencils < 0.25mm wide are difficult to maintain repeatable solder release. • The stencil lead land apertures should therefore be shortened in length by 80% and centered on the lead land. • The land pad aperture should be striped with 0.25mm wide openings and spaces to deposit approximately 50% area of solder on the center pad. If too much solder is deposited on the center pad the part will float and the lead lands will be open. • The maximum length and width of the land pad stencil aperture should be equal to the solder resist opening minus an annular 0.2mm pull back to decrease the incidence of shorting the center land to the lead lands when the part is pushed into the solder paste. Page 46 of 47 June 12, 2007 IR3500 PACKAGE INFORMATION o o 32L MLPQ (5 x 5 mm Body) – θJA = 22.4 C/W, θJC = 0.86 C/W Data and specifications subject to change without notice. This product has been designed and qualified for the Consumer market. Qualification Standards can be found on IR’s Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7903 Visit us at www.irf.com for sales contact information. www.irf.com www.irf.com Page 47 of 47 June 12, 2007