Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide Multipurpose Power Line RFI Filter for Emission Control V and W Series UL Recognized CSA Certified VDE Approved1 VV1 / VW1 VV6 / VW6 Both the V and W series are effective to control emissions in equipment using SCR and T2L circuits for compliance with FCC Part 15, Subpart J and EN55022, Level A, down to 150kHz V Series • Offers an N = 3 (“T”) Line to Ground impedance to common mode and an N = 5 “Dbl. Pi”) impedance for Line to Line differential mode interference • Designed for susceptibility use when equipment impedance at RF frequencies is low W Series • Offers an N = 4 (“Dbl. L”) Line to Ground impedance for common mode and an N=5 (“Dbl. Pi”) impedance for Line to Line differential mode interference • Designed for use when equipment impedance at RF frequencies is high • Two stage construction provides excellent suppression at high frequencies Ordering Information 20 V V 6 Specifications Maximum leakage current each Line to Ground: @ 120 VAC 60 Hz: .5 mA @250 VAC 50 Hz: .82 mA Hipot rating (one minute): Line to Ground: Line to Line: Rated Voltage (max): 250 VAC Operating Frequency: 50/60 Hz Rated Current: 3 to 20A* Operating Ambient Temperature Range (at rated current Ir): -10°C to +40°C In an ambient temperature (Ta) higher than +40°C the maximum operating current (Io) is calculated as follows: Io = Ir (85-Ta)/45 Electrical Schematics V Series LINE (load side) LOAD W Series (3, 6 & 10A) LINE Input / Output Style 1 – .250 [6.3] spade terminals 6 – Threaded bolt 7 – IEC inlet* (line side) .250 [6.3] spade terminals 2250 VDC 1450 VDC LOAD W Series (20A) LINE LOAD V or W Series Leakage current designation V – Standard Current Rating 3, 6, 10 or 20A *IEC 60320-1 C20 inlet mates with C19 connector 120VW7, 20A model tested by Underwriters Laboratories to US and Canadian requirements and is VDE approved at 16A, 250VAC 86 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide Multipurpose Power Line RFI Filter for Emission Control (continued) Case Styles (continued) VW7 V and W Series Threaded inserts Available Part Numbers 3VV1 6VV1 10VV1 20VV1 20VV6 3VW1 3VW1 10VW1 20VW1 20VW6 20VW7* 2.25 57.15 B B Recommended Panel Cutout .157 3.98 Dia. 1.22 30.99 C 2.30 58.42 1.60 40.46 C L .75 19.05 Mounting Plane .219 R 5.56 V1 / W1 (20A) 2.12 53.85 Case Dimensions Part No. E D B 2.00 50.8 A C V6 / W6 E D B A B C 6VV1, 6VW1 10VV1, 10VW1 20VV1, 20VW1 20VV6, 20VW6 20VW7 3VV1, 3VW1 C A RFI Power Line Filters 5.33 ± .025 135.38 ± .635 Case Styles V1 / W1 (3, 6 & 10A) D E A 1 .047 ± .010 1.19 ± .25 D E 2.00 50.8 A C *20VW7, 20A model tested by Underwriters Laboratories to US and Canadian requirements and is VDE approved at 16A, 250VAC 87 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide Multipurpose Power Line RFI Filter for Emission Control (continued) V and W Series Performance Data Typical Insertion Loss Measured in closed 50 Ohm system Common Mode / Asymmetrical (L-G) Differential Mode / Symmetrical (L-L) 3VV 6VV 10VV 20VV db 100 db 100 db 100 db 100 90 90 90 90 80 80 80 80 70 70 70 70 60 60 60 60 50 50 50 50 40 40 40 40 30 30 30 30 20 20 20 20 10 10 10 0 0.1 1 0 10 30 Frequency in MHz 0.1 1 10 30 Frequency in MHz 0 10 0.1 1 0 10 30 Frequency in MHz 0.1 3VW 6VW 10VW 20VW db 100 db 100 db 100 db 100 90 90 90 90 80 80 80 80 70 70 70 70 60 60 60 60 50 50 50 50 40 40 40 40 30 30 30 30 20 20 20 20 10 10 10 0 0 0.1 1 10 30 Frequency in MHz 0.1 1 10 30 Frequency in MHz 0 1 10 30 Frequency in MHz 1 10 30 Frequency in MHz 10 0.1 1 0 10 30 Frequency in MHz 0.1 Minimum Insertion Loss Measured in closed 50 Ohm system Common Mode / Asymmetrical (Line to Ground) Differential Mode / Symmetrical (Line to Line) 88 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com