Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide General Purpose RFI Power Line Filters – Ideal for High Impedance Load K Series UL Recognized CSA Certified VDE Approved** VK6 VK7 / EK7 1 RFI Power Line Filters VK1 / EK1 VK3 / EK3 K Series Specifications • Suitable for high impedance loads • Well suited to applications where pulsed, continuous and/or intermittent RFI interference is present Maximum leakage current each Line to Ground: @ 120 VAC 60 Hz: @250 VAC 50 Hz: VK Models EK Models .5 mA 1.0 mA .21 mA .36 mA • EK models meet the very low leakage current requirements for VDE portable equipment and non-patient care medical equipment Hipot rating (one minute): Line to Ground: Line to Line: • Available with ground line inductor (choke) Rated Voltage (max): 250 VAC Operating Frequency: 50/60 Hz Rated Current: 1 to 60A* Ordering Information 10 E K 7 M Suffix M – Metric inserts (style 7 only) Omit for standard or none C – Ground choke (30, 40VK6 only) Input / Output Style 1 – .250 [6.3] spade terminals 3 – Wire leads 6 – Threaded bolt 7 – IEC inlet* (line side) .250 [6.3] spade terminals (load side) K Series Leakage current designation E – Low leakage (<0.5 mA) V – Standard Current Rating 1, 2, 3, 5, 10, 20, 30, 40 or 60A *1-15A: IEC 60320-1 C14 inlet mates with C13 connector 20VK7: C20 inlet mates with C19 connector 2250 VDC 1450 VDC Operating Ambient Temperature Range (at rated current Ir): -10°C to +40°C In an ambient temperature (Ta) higher than +40°C the maximum operating current (Io) is calculated as follows: Io = Ir (85-Ta)/45 Available Part Numbers 1VK1 1VK3 2VK1 2VK3 3VK1 3VK3 3VK7 3VK7M 5VK1 5VK3 5VK7 5VK7M 10VK1 10VK3 10VK6 10VK7 10VK7M 20VK1 20VK6 20VK7* 30VK6 30VK6C 40VK6 40VK6C 60VK6 1EK1 1EK3 2EK1 2EK3 3EK1 3EK3 3EK7 3EK7M 5EK1 5EK3 5EK7 5EK7M 10EK1 10EK3 10EK7 10EK7M 20EK1 **20VK7, 20A model tested by Underwriters Laboratories to US and Canadian requirements and is VDE approved at 16A, 250VAC 49 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide General Purpose RFI Power Line Filters (continued) K Series Electrical Schematics LINE LOAD Case Styles K1 (1, 2, 3, 6, 10A) E D B 30 & 40VK6C LINE (Inductor in Ground Line) LOAD 60VK6 A C K1 (20A) LINE LOAD E D B Accessories A GA400: NEMA 5-15P to IEC 60320-1 C-13 line cord C K3 Blue Blue Green/Yellow E D B Brown Brown 20VK7 A C 20VK6 VK1/EK1 50 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide General Purpose RFI Power Line Filters (continued) K Series Case Styles (continued) 10VK6 60VK6 1 E D B E D B C 20VK6 C A RFI Power Line Filters 2.00 50.8 A K7 & K7M (3, 5, 10A) Tapped insert D E D B A B E C A C 30VK6/6C & 40VK6/6C Terminal on 30VK6C and 40VK6C only 20VK7 E E D B A D B 2.65 ± .016 67.31 ± .40 C 2.00 50.8 A .669 ± .010 16.99 ± .25 .512 ± .010 13.00 ± .25 C 51 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide General Purpose RFI Power Line Filters (continued) K Series Case Dimensions Part No. 1VK1, 1EK1, 2VK1, 2EK1 1VK3, 1EK3, 2VK3, 2EK3 3VK1, 3EK1, 5VK1, 5EK1 3VK3, 3EK3, 5VK5, 5EK3 3VK7/7M, 3EK7/7M 5VK7/7M, 5EK7/7M 10VK1, 10EK1 10VK3, 10EK3 10VK6 10VK7/7M, 10EK7/7M 20VK1, 20EK1 20VK6 20VK7 30VK6, 30VK6C 40VK6, 40VK6C 60VK6 Recommended Panel Cutouts A B C D E K7 & K7M Cutout (3, 5, 10A) .235 R 5.96 .157 Dia. 3.98 .910 23.1 1.295 32.89 1.575 40.01 20VK7 Cutout .157 Dia. 4.0 R .062 1.60 1.46 37.1 1.145 29.1 D Performance Data Typical Insertion Loss Measured in closed 50 Ohm system 1 & 3EK 2 & 10EK db 100 db 100 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 0 10 0.1 1 10 30 Frequency in MHz 0 0.1 5EK 20EK db 100 db 100 90 90 80 80 70 70 60 60 50 50 40 40 30 30 20 20 10 0 1 10 30 Frequency in MHz 1 10 30 Frequency in MHz 10 0.1 1 10 30 Frequency in MHz 0 0.1 52 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com Catalog: 1654001 Issue Date: 06.2011 Corcom Product Guide General Purpose RFI Power Line Filters (continued) K Series Performance Data (continued) Typical Insertion Loss Measured in closed 50 Ohm system 1VK 2VK 3VK 5VK db 100 db 100 db 100 db 100 90 90 90 90 80 80 80 70 70 70 70 60 60 60 60 80 50 50 50 40 40 40 30 30 30 30 20 20 20 20 10 10 10 0.1 1 0 10 30 Frequency in MHz 0.1 1 10 30 Frequency in MHz 0 10 0.1 1 20VK 30VK & 30VK6C db 100 db 100 db 100 90 90 90 80 80 80 70 70 70 60 60 60 50 50 50 40 40 30 30 30 20 20 20 10 10 0 0.1 1 0 10 30 Frequency in MHz 1 60VK db 100 db 100 90 90 80 80 70 60 60 50 50 40 40 30 30 20 20 1 10 30 Frequency in MHz 10 30 Frequency in MHz 0 0.01 0.1 1 10 30 Frequency in MHz Common Mode / Asymmetrical (L-G) Differential Mode / Symmetrical (L-L) 10 10 0 0.1 10 0.1 40VK & 40VK6C 70 0 10 30 Frequency in MHz 10VK 40 RFI Power Line Filters 50 40 0 1 0.01 0.1 1 0 10 30 Frequency in MHz 0.01 0.1 1 10 30 Frequency in MHz Minimum Insertion Loss Measured in closed 50 Ohm system Common Mode / Asymmetrical (Line to Ground) Differential Mode / Symmetrical (Line to Line) 53 Dimensions are in inches and millimeters unless otherwise specified. Values in italics are metric equivalents. Dimensions are shown for reference purposes only. Specifications subject to change. For email, phone or live chat, please go to te.com/help corcom.com