The documentation and process conversion measures necessary to comply with this revision shall be completed by 4 November 1999. INCH-POUND MIL-PRF-19500/177F 4 August 1999 SUPERSEDING MIL-S-19500/177E 8 February 1995 PERFORMANCE SPECIFICATION SHEET SEMICONDUCTOR DEVICE, TRANSISTOR, PNP, SILICON, LOW-POWER TYPES 2N1131, 2N1131L, 2N1132, 2N1132L, JAN AND JANTX This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the performance requirements for PNP silicon, low-power transistors. Two levels of product assurance are provided for each device type as specified in MIL-PRF-19500. 1.2 Physical dimensions. See figure 1, 2N1131 and 2N1132 (TO-39), 2N1131L and 2N1132L (TO-5). 1.3 Maximum ratings. PT 1/ TC = +25°C PT 2/ TA = +25°C VCBO VCEO VEBO IC TOP and TJ W W V dc V dc V dc mA dc °C 2.0 0.6 50 40 5.0 600 -65 to +200 1/ Derate linearly 11.4 mW/°C for TC ≥ +25°C. 2/ Derate linearly 3.4 mW/°C for TA ≥ +25°C. 1.4 Primary electrical characteristics. hFE1 1/ hfe1 VBE(SAT) 1/ VCE = 10 V dc IC = 150 mA dc VCE = 5.0 V dc IC = 1.0 mA dc f = 1 kHz IC = 150 mA dc IB = 15 mA dc VCE(SAT) 1/ IC = 150 mA dc IB = 15 mA dc V dc 2N1131,L 2N1132,L Min 20 30 Max 45 90 Min 15 30 Max 50 90 Min Cobo f = 1 MHz hfe f = 20 MHz VCB = 10 V dc IE = 0 IC = 50 mA dc VCE = 10 V dc V dc Max 1.5 1.5 Min pF Max 1.3 1.3 Min Max 45 45 Min 2.5 3.0 Max 20 20 1/ Pulsed (see 4.4.1). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Defense Supply Center Columbus, ATTN: DSCC-VAC, 3990 East Broad St., Columbus, OH 43216-5000, by using the addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. FSC 5961 MIL-PRF-19500/177F Symbol CD CH HD LC LD LL LU L1 L2 P Q TL TW r α Dimensions Inches Millimeters Min Max Min Max .305 .335 7.75 5.33 .240 .260 6.10 6.60 .335 .370 8.51 9.40 .100 TP 2.54 TP .016 .021 0.41 0.53 .500 .750 12.70 19.05 .016 .019 0.41 0.48 --.050 --1.27 .250 --6.35 --.100 --2.54 --------.028 .048 0.71 1.22 .028 .034 0.71 0.86 --.010 --0.25 45° TP 45° TP Note 5 5 6 7,8 7,8,13 7,8 7,8 7,8 5 3,4 10 6 NOTES: 1. Dimension are in inches. 2. Metric equivalents are given for general information only. 3. Beyond r (radius) maximum, TL shall be held for a minimum length of .011 (0.28 mm). 4. Dimension TL measured from maximum HD. 5. Body contour optional within zone defined by HD, CD, and Q. 6. Leads at gauge plane .054 +.001 -.000 inch (1.37 +0.03 -0.00 mm) below seating plane shall be within .007 inch (0.18 mm) radius of true position (TP) at maximum material condition (MMC) relative to tab at MMC. The device may be measured by direct methods or by the gauge and gauging procedure shown in figure 2. 7. Dimension LU applies between L1 and L2. Dimension LD applies between L2 and LL minimum. Diameter is uncontrolled in L1 and beyond LL minimum. 8. All three leads. 9. The collector shall be electrically connected to the case. 10. Dimension r (radius) applies to both inside corners of tab. 11. In accordance with ANSI Y14.5M, diameters are equivalent to φx symbology. 12. Lead 1 = emitter, lead 2 = base, lead 3 = collector. 13. For L suffix devices, dimension LL = 1.5 inches (38.10 mm) min. and 1.75 inches (44.45 mm) max. FIGURE 1. Physical dimensions 2N1131 and 2N1132 (TO-39), 2N1131L and 2N1132L (TO-5). 2 MIL-PRF-19500/177F 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specification. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-19500 - Semiconductor Devices, General Specification for. STANDARD MILITARY MIL-STD-750 - Test Methods for Semiconductor Devices. (Unless otherwise indicated, copies of the above specifications, standards, and handbooks are available from the Defense Automated Printing Service, Building 4D (NPM-DODSSP), 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein (except for related associated specifications or specification sheets), the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Associated specifications. The individual item requirements shall be in accordance with MIL-PRF-19500, and as specified herein. 3.2 Abbreviations, symbols, and definitions. Abbreviations, symbols, and definitions used herein shall be as specified in MIL-PRF19500, and as follows: RBE . . . . . . . . . . External resistance, base to emitter. 3.3 Interface requirements and physical dimensions. The Interface requirements and physical dimensions shall be as specified in MILPRF-19500 and herein. 3.3.1 Lead finish. Lead finish shall be solderable in accordance with MIL-PRF-19500, MIL-STD-750, and herein (see 6.2). 3.4 Marking. Marking shall be in accordance with MIL-PRF-19500. 3.5 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in 1.3, 1.4, and table I. 3.6 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table I. 3.7 Qualification. Devices furnished under this specification shall be products that are authorized by the qualifying activity for listing on the applicable qualified manufacturers list before contract award (see 4.2 and 6.4 ). 3 MIL-PRF-19500/177F 4. VERIFICATION 4.1 Classification of Inspections. The inspection requirements specified herein are classified as follows: a. Qualification inspection (see 4.2). b. Screening (see 4.3) c. Conformance inspection (see 4.4). 4.2 Qualification inspection. Qualification inspection shall be in accordance with MIL-PRF-19500, and as specified herein. 4.2.1 Thermal resistance. Thermal resistance testing shall be performed in accordance with MIL-STD-750, method 3151 for qualification only. 4.3 Screening (JANTX level only). Screening shall be in accordance with table IV of MIL-PRF-19500, and as specified herein. The following measurement shall be made in accordance with table I herein. Devices that exceed the limits of table I herein shall not be acceptable. Screening (see table IV of MIL-PRF-19500) 9 11 Measurements JANTX level only Not applicable ICBO1 and hFE2 12 TA = room ambient as defined in the general requirements of MIL-STD-750, VCB = 30 V dc; adjust PT to achieve TJ = 150°C min. 13 ∆ICBO1 = 100 percent of initial value or 10 µA dc whichever is greater; ∆hFE2 = ±20 percent of initial value; subgroup 2 of table I herein. 4.4 Conformance inspection. Conformance inspection shall be in accordance with MIL-PRF-19500, and as specified herein. 4.4.1 Group A inspection. Group A inspection shall be conducted in accordance with MIL-PRF-19500, and table I herein. 4.4.2 Group B inspection. Group B inspection shall be conducted in accordance with the conditions specified for subgroup testing in table VIb (JAN and JANTX) of MIL-PRF-19500, and as follows. Electrical measurements (end-points) shall be in accordance with table I, group A, subgroup 2 herein. Subgroup Method Conditions B3 1027 TA = room ambient as defined in the general requirements of MIL-STD-750, VCB = 30 V dc; adjust PT to achieve TJ = 150°C min. B3 2037 Test condition A. B5 3161 For qualification only. B6 1032 TSTG(max) = +175°C 4.4.3 Group C inspection. Group C inspection shall be conducted in accordance with the conditions specified for subgroup testing in table VII of MIL-PRF-19500, and as follows. Electrical measurements (end-points) and delta requirements shall be in accordance with table I, group A, subgroup 2 herein. Subgroup Method Conditions C2 2036 Test condition E. C6 1026 TA = room ambient as defined in the general requirements of MIL-STD-750, VCB = 30 V dc; adjust PT to achieve TJ = 150°C min. 4.5 Methods of inspection. Methods of inspection shall be as specified in the appropriate tables and as follows. 4.5.1 Pulse measurements. Conditions for pulse measurement shall be as specified in section 4 of MIL-STD-750. 4 MIL-PRF-19500/177F TABLE I. Group A inspection. Inspection Method MIL-STD-750 Conditions Symbol Limits Min Unit Max Subgroup 1 Visual and mechanical examination 2071 Subgroup 2 Collector - emitter breakdown voltage 3011 Bias condition D; IC = 10 mA dc; pulsed (see 4.5.1) V(BR)CEO 40 V dc Collector - base breakdown voltage 3001 Bias condition D; IC = 10 µA dc V(BR)CBO 50 V dc Collector - base cutoff current 3036 Bias condition D; VCB = 50 V dc ICBO1 10 µA dc Collector - emitter cutoff current 3041 Bias condition B; VCE = 50 V dc; pulsed (see 4.5.1); RBE ≤ 10 ohms ICER 10 mA dc Collector – base cutoff current 3036 Bias condition D; VCB = 30 V dc ICBO2 1.0 µA dc Emitter - base cutoff current 3061 Bias condition D; VEB = 5.0 V dc IEBO 100 µA dc Forward-current transfer ratio 3076 VCE = 10 V dc; IC = 150 mA dc; pulsed (see 4.5.1) hFE1 2N1131, L 2N1132, L Forward-current transfer ratio 20 30 3076 VCE = 10 V dc; IC = 5.0 mA dc; pulsed (see 4.5.1) 45 90 hFE2 2N1131, L 2N1132, L 15 25 Collector - emitter saturated voltage 3071 IC = 150 mA dc; IB = 15 mA dc; pulsed (see 4.5.1) VCE(SAT) 1.3 V dc Base – emitter saturated voltage 3066 Test condition A; IC = 150 mA dc; IB = 15 mA dc; pulsed (see 4.5.1) VBE(SAT) 1.5 V dc 100 µA dc Subgroup 3 High-temperature operation: TA = +150°C Collector - base cutoff current 3036 Bias condition D; VCE = 30 V dc ICBO3 Low-temperature operation: Forward-current transfer ratio 3076 TA = -55°C VCE = 10 V dc; IC = 150 mA dc; pulsed (see 4.5.1) hFE3 2N1131, L 2N1132, L 10 15 See footnote at end of table. 5 MIL-PRF-19500/177F TABLE I. Group A inspection. Inspection Method MIL-STD-750 Conditions Symbol Limits Unit Min Max 15 30 50 90 Subgroup 4 Small-signal short circuit forward-current transfer ratio 2N1131, L 2N1132, L 3206 Small-signal short circuit forward-current transfer ratio 2N1131, L 2N1132, L 3206 Small-signal open-circuit output admittance 3216 VCE = 5.0 V dc; IC = 1.0 mA dc hob1 1.0 µmho Small-signal open-circuit output admittance 3216 VCE = 10 V dc; IC = 5.0 mA dc hob2 5.0 µmho Small-signal short-circuit input impedance 3201 VCE = 5.0 V dc; IC = 1.0 mA dc hib1 35 Ω Small-signal short-circuit input impedance 3201 VCE = 10 V dc; IC = 5.0 mA dc hib2 10 Ω Small-signal open-circuit reverse-voltage transfer ratio 3211 VCE = 5.0 V dc; IC = 1.0 mA dc hrb1 8x10 Small-signal open-circuit reverse-voltage transfer ratio 3211 VCE = 10 V dc; IC = 5.0 mA dc hrb2 8x10 Magnitude of common emitter small-signal short-circuit forward-current transfer ratio 3306 VCE = 10 V dc; IC = 50 mA dc; f = 20 MHz | hfe | VCE = 5.0 V dc; IC = 1.0 mA dc; f = 1 kHz VCE = 10 V dc; IC = 5.0 mA dc; f = 1 kHz hfe1 hfe2 20 30 2N1131, L 2N1132, L 25 -4 -4 2.5 3.0 20 20 Open circuit output capacitance 3236 VCB = 10 V dc; IE = 0; 100 kHz ≤ f ≤ 1.0 MHz Cobo 45 pF Input capacitance (output open-circuited) 3240 VEB = 0.5 V dc; IC = 0; 100 kHz ≤ f ≤ 1.0 MHz Cibo 80 pF ton + toff 50 ns Pulse response (see figure 2) Subgroups 5, 6 and 7 Not applicable 1/ For sampling plan, see MIL-PRF-19500. 6 MIL-PRF-19500/177F NOTES: 1. The rise time (tr) of the applied pulse shall be ≤ 2.0 ns, duty cycle ≤ 2 percent, and the generator source shall be 50 Ω. 2. Sampling oscilloscope: Zin ≥ 100 kΩ, Cin ≤ 12 pF, rise time ≤ .5 ns. FIGURE 2. Nonsaturated switching time test circuit. 7 MIL-PRF-19500/177F 5. PACKAGING 5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see 6.2). When actual packaging of material is to be performed by DoD personnel, these personnel need to contact the responsible packaging activity to ascertain requisite packaging requirements. Packaging requirements are maintained by the Inventory Control Points' packaging activity within the Military Department or Defense Agency, or within the Military Departments' System Command. Packaging data retrieval is available from the managing Military Departments' or Defense Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity. 6. NOTES (This section contains information of a general or explanatory nature that may be helpful, but is not mandatory.) 6.1 Notes. The notes specified in MIL-PRF-19500 are applicable to this specification. 6.2 Acquisition requirements. Acquisition documents should specify the following: a. Issue of DODISS to be cited in the solicitation and, if required, the specific issue of individual documents referenced (see 2.2.1). b. Lead finish (see 3.3.1). c. Type designation and product assurance level. d. Packaging requirements (see 5.1). 6.3 Changes from previous issue. Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. 6.4 Qualification. With respect to products requiring qualification, awards will be made only for products which are, at the time of award of contract, qualified for inclusion in Qualified Manufacturers List QML-19500 whether or not such products have actually been so listed by that date. The attention of the contractors is called to these requirements, and manufacturers are urged to arrange to have the products that they propose to offer to the Federal Government tested for qualification in order that they may be eligible to be awarded contracts or purchase orders for the products covered by this specification. Information pertaining to qualification of products may be obtained from Defense Supply Center Columbus, DSCC-VQE, Columbus, OH 43216. CONCLUDING MATERIAL Custodians: Army - CR Navy - EC Air Force - 11 DLA - CC Preparing activity: DLA - CC (Project 5961-1920) Review activities: Army - AR, AV, MI, SM Navy - AS, CG, MC Air Force - 13, 19, 99 8 MIL-PRF-19500/177F STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL INSTRUCTIONS 1. The preparing activity must complete blocks 1, 2, 3, and 8. In block 1, both the document number and revision letter should be given. 2. The submitter of this form must complete blocks 4, 5, 6, and 7. 3. The preparing activity must provide a reply within 30 days from receipt of the form. NOTE: This form may not be used to request copies of documents, nor to request waivers, or clarification of requirements on current contracts. Comments submitted on this form do not constitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual requirements. I RECOMMEND A CHANGE: 1. DOCUMENT NUMBER MIL-PRF-19500/177F 2. DOCUMENT DATE 99/08/04 3. DOCUMENT TITLE SEMICONDUCTOR DEVICE, TRANSISTOR, PNP, SILICON, LOW-POWER TYPES 2N1131, 2N1131L, 2N1132, 2N1132L, JAN AND JANTX 4. NATURE OF CHANGE (Identify paragraph number and include proposed rewrite, if possible. Attach extra sheets as needed.) 5. REASON FOR RECOMMENDATION 6. SUBMITTER a. NAME (Last, First, Middle initial) c. ADDRESS (Include Zip Code) b. ORGANIZATION d. TELEPHONE (Include Area Code) Commercial DSN FAX EMAIL 7. DATE SUBMITTED 8. PREPARING ACTIVITY a. Point of Contact Alan Barone c. ADDRESS Defense Supply Center Columbus ATTN: DSCC-VAC Columbus, OH 43216-5000 DD FORM 1426, FEB 99 (EG) b. TELEPHONE Commercial DSN 614-692-0510 850-0510 FAX 614-692-6939 EMAIL [email protected] IF YOU DO NOT RECEIVE A REPLY WITHIN 45 DAYS, CONTACT: Defense Standardization Program Office (DLSC -LM) 8725 John J. Kingman Road, Suite 2533 Fort Belvior, Virginia 22060-6221 Telephone (703) 767-6888 DSN 427-6888 PREVIOUS EDITIONS ARE OBSOLETE 9 WHS/DIOR, Feb 99