LMV551/LMV552 3 MHz, Micropower RRO Amplifier General Description Features The LMV551/LMV552 are high performance, low power operational amplifiers implemented with National’s advanced VIP50 process. They feature 3 MHz of bandwidth while consuming only 34 μA of current per amplifier, which is an exceptional bandwidth to power ratio in this op amp class. These amplifiers are unity gain stable and provide an excellent solution for low power applications requiring a wide bandwidth. The LMV551/LMV552 have a rail-to-rail output stage and an input common mode range that extends below ground. The LMV551/LMV552 have an operating supply voltage range from 2.7V to 5.5V. These amplifiers can operate over a wide temperature range (−40°C to +125°C) making them a great choice for automotive applications, sensor applications as well as portable instrumentation applications. The LMV551 is offered in the ultra tiny 5-Pin SC70 package. The LMV552 is offered in an 8-Pin MSOP package. (Typical 5V supply, unless otherwise noted) ■ Guaranteed 3V and 5.0V performance 3 MHz ■ High unity gain bandwidth 37 µA ■ Supply current (per amplifier) 93 dB ■ CMRR 90 dB ■ PSRR 1 V/µs ■ Slew rate 70 mV from rail ■ Output swing with 100 kΩ load 0.003% @ 1 kHz, 2 kΩ ■ Total harmonic distortion −40°C to 125°C ■ Temperature range Applications ■ ■ ■ ■ Portable equipment Automotive Battery powered systems Sensors and Instrumentation Typical Application 20152601 20152613 Open Loop Gain and Phase vs. Frequency © 2007 National Semiconductor Corporation 201526 www.national.com LMV551/LMV552 3 MHz, Micropower RRO Amplifier February 2007 LMV551/LMV552 Storage Temperature Range Junction Temperature (Note 3) Soldering Information Infrared or Convection (20 sec) Wave Soldering Lead Temp. (10 sec) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Human Body Model LMV551/LMV552 Machine Model LMV551 LMV552 VIN Differential Supply Voltage (V+ - V−) Voltage at Input/Output pins Operating Ratings 2 KV −65°C to +150°C +150°C 235°C 260°C (Note 1) Temperature Range (Note 3) Supply Voltage (V+ – V−) 100V 250V ±2.5V 6V V+ +0.3V, V− −0.3V −40°C to +125°C 2.7V to 5.5V Package Thermal Resistance (θJA (Note 3)) 5-Pin SC70 8-Pin MSOP 456°C/W 235°C/W 3V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 3V, V− = 0V, VCM = V+/2 = VO. Boldface limits apply at the temperature extremes. (Note 4) Symbol Parameter VOS Input Offset Voltage TC VOS Input Offset Average Drift IB Input Bias Current IOS Input Offset Current CMRR Common Mode Rejection Ratio PSRR Power Supply Rejection Ratio CMVR AVOL VO Min (Note 6) Typ (Note 5) Max (Note 6) 1 3 4.5 38 nA 1 20 nA 0V ≤ VCM 2.0V 3.0 ≤ V+ ≤ 5V, VCM = 0.5V 80 78 92 2.7 ≤ V+ ≤ 5.5V, VCM = 0.5V 80 78 92 Input Common-Mode Voltage Range CMRR ≥ 68 dB 0 0 Large Signal Voltage Gain 0.4 ≤ VO ≤ 2.6, RL = 100 kΩ to V+/2 81 78 90 0.4 ≤ VO ≤ 2.6, RL = 10 kΩ to V+/2 71 68 80 Output Swing High Output Short Circuit Current dB dB 2.1 2.1 40 48 58 RL = 10 kΩ to V+/2 85 100 120 50 65 77 RL = 10 kΩ to V+/2 95 110 130 Sourcing (Note 9) 10 Sinking (Note 9) 25 RL = 100 kΩ to mV from rail mA IS Supply Current per Amplifier SR Slew Rate AV = +1, 10% to 90% (Note 8) 1 V/μs Φm Phase Margin RL = 10 kΩ, CL = 20 pF 75 Deg GBW Gain Bandwidth Product 3 MHz en Input-Referred Voltage Noise f = 100 kHz 70 f = 1 kHz 70 www.national.com 34 V dB RL = 100 kΩ to V+/2 V+/2 mV 20 92 CMRR ≥ 60 dB Units μV/°C 6.6 (Note 7) 74 72 Output Swing Low ISC Conditions 2 42 52 μA nV/ in Parameter Input-Referred Current Noise THD Total Harmonic Distortion Conditions Min (Note 6) Typ (Note 5) f = 100 kHz 0.1 f = 1 kHz 0.15 f = 1 kHz, AV = 2, RL = 2 kΩ 0.003 Max (Note 6) Units pA/ % 5V Electrical Characteristics Unless otherwise specified, all limits are guaranteed for TA = 25°C, V+ = 5V, V− = 0V, VCM = V+/2 = VO. Boldface limits apply at the temperature extremes. Symbol Parameter VOS Input Offset Voltage TC VOS Input Offset Average Drift IB Input Bias Current IOS Input Offset Current CMRR Common Mode Rejection Ratio PSRR Power Supply Rejection Ratio CMVR AVOL VO Min (Note 6) Typ (Note 5) Max (Note 6) 1 3.0 4.5 38 nA 1 20 nA 0 ≤ VCM ≤ 4.0V 3V ≤ V+ ≤ 5V to VCM = 0.5V 78 75 90 2.7V ≤ V+ ≤ 5.5V to VCM = 0.5V 78 75 90 Input Common-Mode Voltage Range CMRR ≥ 68 dB 0 0 Large Signal Voltage Gain 0.4 ≤ VO ≤ 4.6, RL = 100 kΩ to V+/2 78 75 90 0.4 ≤ VO ≤ 4.6, RL = 10 kΩ to V+/2 75 72 80 Output Swing High Output Short Circuit Current mV 20 93 CMRR ≥ 60 dB Units μV/°C 6.6 (Note 7) 76 74 Output Swing Low ISC Conditions dB dB 4.1 4.1 dB RL = 100 kΩ to V+/2 70 92 122 RL = 10 kΩ to V+/2 125 155 210 RL = 100 kΩ to V+/2 60 70 82 RL = 10 kΩ to V+/2 110 130 155 Sourcing (Note 9) 10 Sinking (Note 9) 25 mV from rail mA IS Supply Current Per Amplifier SR Slew Rate AV = +1, VO = 1 VPP 10% to 90% (Note 8) 1 V/μs Φm Phase Margin RL = 10 kΩ, CL = 20 pF 75 Deg GBW Gain Bandwidth Product 3 MHz en Input-Referred Voltage Noise f = 100 kHz 70 f = 1 kHz 70 in THD Input-Referred Current Noise Total Harmonic Distortion 37 V f = 100 kHz 0.1 f = 1 kHz 0.15 f = 1 kHz, AV = 2, RL = 2 kΩ 0.003 3 46 54 μA nV/ pA/ % www.national.com LMV551/LMV552 Symbol LMV551/LMV552 Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics Tables. Note 2: Human Body Model, applicable std. MIL-STD-883, Method 3015.7. Machine Model, applicable std. JESD22-A115-A (ESD MM std. of JEDEC) Field-Induced Charge-Device Model, applicable std. JESD22-C101-C (ESD FICDM std. of JEDEC). Note 3: The maximum power dissipation is a function of TJ(MAX), θJA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX) - TA)/ θJA. All numbers apply for packages soldered directly onto a PC board. Note 4: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating of the device such that TJ = TA. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self-heating where TJ > TA. Note 5: Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. The typical values are not tested and are not guaranteed on shipped production material. Note 6: Limits are 100% production tested at 25°C. Limits over the operating temperature range are guaranteed through correlations using statistical quality control (SQC) method. Note 7: Positive current corresponds to current flowing into the device. Note 8: Slew rate is the average of the rising and falling slew rates. Note 9: The part is not short circuit protected and is not recommended for operation with heavy resistive loads. Connection Diagrams 5-Pin SC70 8-Pin MSOP 20152602 Top View 20152611 Top View Ordering Information Package 5-Pin SC70 8-Pin MSOP www.national.com Part Number LMV551MG LMV551MGX LMV552MM LMV552MMX Package Marking Transport Media 1k Units Tape and Reel A94 3k Units Tape and Reel 1k Units Tape and Reel AH3A 3.5k Units Tape and Reel 4 NSC Drawing MAA05A MUA08A Open Loop Gain and Phase with Capacitive Load Open Loop Gain and Phase with Resistive Load 20152615 20152614 Open Loop Gain and Phase with Resistive Load Open Loop Gain and Phase with Resistive Load 20152616 20152617 Open Loop Gain and Phase with Resistive Load Slew Rate vs. Supply voltage 20152618 20152619 5 www.national.com LMV551/LMV552 Typical Performance Characteristics LMV551/LMV552 Small Signal Transient Response Large Signal Transient Response 20152620 20152621 Small Signal Transient Response Input Referred Noise vs. Frequency 20152622 20152623 THD+N vs. Amplitude @ 3V THD+N vs. Amplitude @ 5V 20152624 www.national.com 20152625 6 LMV551/LMV552 THD+N vs. Amplitude THD+N vs. Amplitude 20152626 20152627 Supply Current vs. Supply Voltage VOS vs. VCM 20152628 20152629 VOS vs. VCM VOS vs. Supply Voltage 20152630 20152631 7 www.national.com LMV551/LMV552 IBIAS vs. VCM IBIAS vs. VCM 20152632 20152633 IBIAS vs. Supply Voltage Positive Output Swing vs. Supply Voltage 20152635 20152634 Negative Output Swing vs. Supply Voltage Positive Output Swing vs. Supply Voltage 20152636 www.national.com 20152637 8 LMV551/LMV552 Negative Output Swing vs. Supply Voltage 20152638 STABILITY OF OP AMP CIRCUITS Applications Information Stability and Capacitive Loading As seen in the Phase Margin vs. Capacitive Load graph, the phase margin reduces significantly for CL greater than 100 pF. This is because the op amp is designed to provide the maximum bandwidth possible for a low supply current. Stabilizing them for higher capacitive loads would have required either a drastic increase in supply current, or a large internal compensation capacitance, which would have reduced the bandwidth of the op amp. Hence, if the LMV551/LMV552 are to be used for driving higher capacitive loads, they will have to be externally compensated. ADVANTAGES OF THE LMV551/LMV552 Low Voltage and Low Power Operation The LMV551/LMV552 have performance guaranteed at supply voltages of 3V and 5V and are guaranteed to be operational at all supply voltages between 2.7V and 5.5V. For this supply voltage range, the LMV551 draws the extremely low supply current of less than 37 μA. Wide Bandwidth The LMV551's bandwidth to power ratio of 3 MHz to 37 μA per amplifier is one of the best bandwidth to power ratios ever achieved. This makes these devices ideal for low power signal processing applications such as portable media players and instrumentation. Low Input Referred Noise The LMV551/LMV552 provide a flatband input referred volt, which is significantly better age noise density of 70 nV/ than the noise performance expected from an ultra low power op amp. They also feature the exceptionally low 1/f noise corner frequency of 4 Hz. This noise specification makes the LMV551/LMV552 ideal for low power applications such as PDAs and portable sensors. Ground Sensing and Rail-to-Rail Output The LMV551/LMV552 each have a rail-to-rail output stage, which provides the maximum possible output dynamic range. This is especially important for applications requiring a large output swing. The input common mode range includes the negative supply rail which allows direct sensing at ground in a single supply operation. 20152603 FIGURE 1. Gain vs. Frequency for an Op Amp Small Size The small footprints of the LMV551/LMV552 packages save space on printed circuit boards, and enable the design of smaller and more compact electronic products. Long traces between the signal source and the op amp make the signal path susceptible to noise. By using a physically smaller package, the amplifiers can be placed closer to the signal source, reducing noise pickup and enhancing signal integrity An op amp, ideally, has a dominant pole close to DC, which causes its gain to decay at the rate of 20 dB/decade with respect to frequency. If this rate of decay, also known as the rate of closure (ROC), remains the same until the op amp’s unity gain bandwidth, the op amp is stable. If, however, a large capacitance is added to the output of the op amp, it combines with the output impedance of the op amp to create another pole in its frequency response before its unity gain frequency (Figure 1). This increases the ROC to 40 dB/ decade and causes instability. 9 www.national.com LMV551/LMV552 In such a case a number of techniques can be used to restore stability to the circuit. The idea behind all these schemes is to modify the frequency response such that it can be restored to an ROC of 20 dB/decade, which ensures stability. is shown in Figure 3. A resistor, RISO, is placed in series between the load capacitance and the output. This introduces a zero in the circuit transfer function, which counteracts the effect of the pole formed by the load capacitance and ensures stability. The value of RISO to be used should be decided depending on the size of CL and the level of performance desired. Values ranging from 5Ω to 50Ω are usually sufficient to ensure stability. A larger value of RISO will result in a system with lesser ringing and overshoot, but will also limit the output swing and the short circuit current of the circuit. In The Loop Compensation Figure 2 illustrates a compensation technique, known as ‘in the loop’ compensation, that employs an RC feedback circuit within the feedback loop to stabilize a non-inverting amplifier configuration. A small series resistance, RS, is used to isolate the amplifier output from the load capacitance, CL, and a small capacitance, CF, is inserted across the feedback resistor to bypass CL at higher frequencies. 20152612 FIGURE 3. Compensation by Isolation Resistor Typical Application ACTIVE FILTERS With a wide unity gain bandwidth of 3 MHz, low input referred noise density and a low power supply current, the LMV551/ LMV552 are well suited for low-power filtering applications. Active filter topologies, such as the Sallen-Key low pass filter shown in Figure 4, are very versatile, and can be used to design a wide variety of filters (Chebyshev, Butterworth or Bessel). The Sallen-Key topology, in particular, can be used to attain a wide range of Q, by using positive feedback to reject the undesired frequency range. In the circuit shown in Figure 4, the two capacitors appear as open circuits at lower frequencies and the signal is simply buffered to the output. At high frequencies the capacitors appear as short circuits and the signal is shunted to ground by one of the capacitors before it can be amplified. Near the cutoff frequency, where the impedance of the capacitances is on the same order as RG and RF, positive feedback through the other capacitor allows the circuit to attain the desired Q. 20152604 FIGURE 2. In the Loop Compensation The values for RS and CF are decided by ensuring that the zero attributed to CF lies at the same frequency as the pole attributed to CL. This ensures that the effect of the second pole on the transfer function is compensated for by the presence of the zero, and that the ROC is maintained at 20 dB/ decade. For the circuit shown in Figure 2 the values of RS and CF are given by Equation 1. Values of RS and CF required for maintaining stability for different values of CL, as well as the phase margins obtained, are shown in Table 1. RF, RIN, and RL are to be 10 kΩ, while ROUT is 340Ω. (1) TABLE 1. CL (pF) RS (Ω) CF (pF) Phase Margin (°) 50 340 8 47 100 340 15 42 150 340 22 40 Although this methodology provides circuit stability for any load capacitance, it does so at the price of bandwidth. The closed loop bandwidth of the circuit is now limited by RF and CF. 20152609 Compensation By External Resistor In some applications it is essential to drive a capacitive load without sacrificing bandwidth. In such a case, in the loop compensation is not viable. A simpler scheme for compensation www.national.com FIGURE 4. 10 LMV551/LMV552 Physical Dimensions inches (millimeters) unless otherwise noted 5-Pin SC70 NS Package Number MAA05A 8-Pin MSOP NS Package Number MUA08A 11 www.national.com LMV551/LMV552 3 MHz, Micropower RRO Amplifier Notes THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION (“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright© 2007 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Customer Support Center Email: [email protected] Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530-85-86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +49 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: [email protected] National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: [email protected] Tel: 81-3-5639-7560