LTC3541 High Efficiency Buck + VLDO Regulator FEATURES DESCRIPTIO High Efficiency, 500mA Buck Plus 300mA VLDOTM Regulator Auto Start-Up Powers Buck Output Prior to VLDO/Linear Regulator Output ■ Independent High Efficiency, 500mA Buck (VIN: 2.7V to 5.5V) ■ 300mA VLDO Regulator with 30mA Standalone Mode ■ No External Schottky Diodes Required ■ Buck Output Voltage Range: 0.8V to 5V ■ VLDO Input Voltage Range (LV ): 0.9V to 5.5V IN ■ VLDO Output Voltage Range VLDO: 0.4V to 4.1V ■ Selectable Fixed Frequency, Pulse-Skip Operation or Burst Mode® Operation ■ Short-Circuit Protected ■ Current Mode Operation for Excellent Line and Load Transient Response ■ Constant Frequency Operation: 2.25MHz ■ Low Dropout Buck Operation: 100% Duty Cycle ■ Small, Thermally Enhanced, 10-Lead (3mm × 3mm) DFN Package The LTC ®3541 combines a synchronous buck DC/DC converter with a very low dropout linear regulator (VLDO) to provide up to two output voltages from a single input voltage with minimal external components. When configured for dual output operation, the LTC3541’s auto start-up feature will bring the Buck output into regulation in a controlled manner prior to enabling the VLDO regulator output without the need for external pin control. VLDO/ linear regulator output prior to Buck output sequencing may also be obtained via external pin control. The input voltage range is ideally suited for Li-Ion battery-powered applications, as well as powering sub-3.3V logic from 5V or 3.3V rails. U ■ U APPLICATIO S ■ ■ ■ ■ ■ ■ The synchronous buck converter provides a high efficiency output, typically 90%, capable of providing up to 500mA of continuous output current while switching at 2.25MHz, allowing the use of small surface mount inductors and capacitors. A mode-select pin allows Burst Mode operation to be enabled for higher efficiency at light load currents, or disabled for lower noise, constant frequency operation. The VLDO regulator provides a low noise, low voltage output capable of providing up to 300mA of continuous output current using only a 2.2µF ceramic capacitor. The input supply voltage of the VLDO regulator (LVIN) may come from the buck regulator or a separate supply. PDAs/Palmtop PCs Digital Cameras Cellular Phones PC Cards Wireless and DSL Modems Other Portable Power Systems , LT, LTc and LTM are registered trademarks of Linear Technology corporation. VLDO is a trademark of Linear Technology corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 5481178, 6611131, 6304066, 6498466, 6580258 TYPICAL APPLICATIO Buck (Burst) Efficiency and Power Loss vs Load Current U 100 LTC3541 Typical Application VIN 243k MODE LTC3541 ENBUCK GND 22pF BUCKFB 2.2µH LVIN 115k LFB LVOUT PGND EFFICIENCY (%) ENVLDO 150k 412k 2.2µF 3541 TA01a 0.1 70 60 POWER LOSS 50 0.01 40 30 0.001 20 VOUT2 1.5V 300mA VIN = 3.3V VOUT = 2.5V 10 0 POWER LOSS (W) SW 10µF EFFICIENCY 80 VIN 2.9V TO 5.5V VOUT1 2.5V 200mA 1 90 1 10 100 LOAD CURRENT (mA) 0.0001 1000 3541 TA01b 3541fa LTC3541 W W W (Note 1) AXI U RATI GS U ABSOLUTE Supply Voltages: VIN, LVIN................................................... –0.3V to 6V LVIN – VIN...........................................................<0.3V Pin Voltages: ENVLDO, ENBUCK, MODE, SW, LFB, BUCKFB..............................–0.3V to (VIN + 0.3V) Linear Regulator IOUT(MAX) (100ms) (Note 9).......100mA Operating Ambient Temperature Range (Note 2)..................................................... –40°C to 85°C Junction Temperature (Note 5).............................. 125°C Storage Temperature Range.................... –65°C to 125°C U W U PACKAGE/ORDER I FOR ATIO TOP VIEW 10 SW VIN 1 ENBUcK 2 BUcKFB 3 LFB 4 7 GND LVOUT 5 6 LVIN 9 ENVLDO 11 8 MODE DD PAcKAGE 10-LEAD (3mm × 3mm) PLASTIc DFN TJMAX = 125°C, θJA = 43°C/W EXPOSED PAD (PIN 11) IS GND, MUST BE SOLDERED TO PCB Order part number DD part marking LTC3541EDD lcbs Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges. ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 3.6V unless otherwise specified (Note 2) SYMBOL IPK PARAMETER Peak Inductor Current CONDITIONS VIN = 4.2V (Note 8) IBUCKFB BUCKFB Pin Input Current VBUCKFB = 0.9V l ILFB LFB Pin Input Current VLFB = 0.45V l –200 VIN Input Voltage Range (Note 4) l 2.7 VIN(LINEREG) Buck VIN Line Regulation VIN = 2.7V to 5.5V, ENBUCK = VIN, ENVLDO = 0V, MODE = VIN (Note 6) VIN = 2.7V to 5.5V, LVOUT = 1.2V, ENBUCK = VIN, ENVLDO = VIN, IOUT(VLDO) = 100mA, LVIN = 1.5V VIN = 2.7V to 5.5V, LVOUT = 1.2V, ENBUCK = 0V, ENVLDO = VIN, IOUT(LREG) = 10mA LVIN = 0.9V to 5.5V, VIN = 5.5V, LVOUT = 0.4V, ENBUCK = VIN, ENVLDO = VIN, MODE = VIN, IOUT(VLDO) = 100mA LVIN = 1.5V, ENBUCK = VIN, ENVLDO = VIN, MODE = VIN, IOUT(VLDO) = 50mA, VLFB = 0.3V ENBUCK = VIN, ENVLDO = 0V, MODE = VIN (Note 6) l IOUT(VLDO) = 1mA – 300mA, LVIN = 1.5V, LVOUT = 1.2V, ENBUCK = VIN, ENVLDO = VIN, MODE = VIN IOUT(LREG) = 1mA – 30mA, LVOUT = 1.2V, ENBUCK = 0V, ENVLDO = VIN ENBUCK = VIN, ENVLDO = 0V, TA = 25°C l 0.25 0.5 % l 0.25 0.5 % 0.784 0.8 0.816 V 0.782 0.8 0.818 V VLDO VIN Line Regulation (Referred to LFB) Linear Regulator VIN Line Regulation (Referred to LFB) LVIN(LINEREG) LVIN Line Regulation (Referred to LFB) VLDODO VLOADREG LVIN – LVOUT Dropout Voltage (Note 9) Buck Output Load Regulation VLDO Output Load Regulation Linear Regulator Output Load VBUCKFB Reference Regulation Voltage (Note 6) Reference Regulation Voltage (Note 7) MAX 1.25 UNITS A ±50 nA –40 0.04 nA 5.5 V 0.4 %/V 0.6 mV/V 0.6 mV/V 0.3 mV/V 60 0.5 l ENBUCK = 0V, ENVLDO = VIN, TA = 25°C ENBUCK = 0V, ENVLDO = VIN, 0°C ≤ TA ≤ 85°C ENBUCK = 0V, ENVLDO = VIN, –40°C ≤ TA ≤ 85°C TYP 0.95 28 ENBUCK = VIN, ENVLDO = 0V, 0°C ≤ TA ≤ 85°C ENBUCK = VIN, ENVLDO = 0V, –40°C ≤ TA ≤ 85°C VLFB MIN 0.8 l mV % 0.78 0.8 0.82 V 0.392 0.4 0.408 V 0.391 0.4 0.409 V 0.390 0.4 0.410 V 3541fa LTC3541 ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C. VIN = 3.6V unless otherwise specified (Note 2) SYMBOL IS PARAMETER Buck + VLDO Burst Mode Sleep VIN Quiescent Current Buck + VLDO Burst Mode Active VIN Quiescent Current Buck + VLDO Pulse-Skip Mode Active VIN Quiescent Current Buck Burst Mode Sleep VIN Quiescent Current Buck Burst Mode Active VIN Quiscent Current Buck Pulse-Skip Mode Active VIN Quiescent Current Linear Regulator VIN Quiescent Current VIN Shutdown Quiescent Current CONDITIONS LVIN = 1.5V, LVOUT = 1.2V, ENBUCK = VIN, ENVLDO = VIN, MODE = 0V, IOUT(VLDO) = 10µA, VBUCKFB = 0.9V LVIN = 1.5V, LVOUT = 1.2V, ENBUCK = VIN, ENVLDO = VIN, MODE = 0V, IOUT(VLDO) = 10µA, VBUCKFB = 0.7V LVIN = 1.5V, LVOUT = 1.2V, ENBUCK = VIN, ENVLDO = VIN, MODE = VIN, IOUT(VLDO) = 10µA, VBUCKFB = 0.7V VBUCKFB = 0.9V, IOUT(BUCK) = 0A, ENBUCK = VIN, ENVLDO = 0V, MODE = 0V MIN TYP 85 MAX UNITS µA 315 µA 300 µA 55 µA VBUCKFB = 0.7V, IOUT(BUCK) = 0A, ENBUCK = VIN, ENVLDO = 0V, MODE = 0V 300 µA VBUCKFB = 0.7V, IOUT(BUCK) = 0A, ENBUCK = VIN, ENVLDO = 0V, MODE = VIN 285 µA LVOUT = 1.2V, ENBUCK = 0V, ENVLDO = VIN, IOUT(LREG) = 10µA ENBUCK = 0V, ENVLDO = 0V 50 µA 2.5 µA 0.1 µA LVIN Shutdown Quiescent Current LVIN = 3.6V, ENBUCK = 0V, ENVLDO = 0V fOSC Oscillator Frequency RPFET RDS(ON) of P-Channel MOSFET ISW = 100mA 0.25 Ω RNFET RDS(ON) of N-Channel MOSFET ISW = 100mA 0.35 Ω ILSW SW Leakage Enable = 0V, VSW = 0V or 6V, VIN = 6V VIH Input Pin High Threshold MODE, ENBUCK, ENVLDO l VIL Input Pin Low Threshold MODE, ENBUCK, ENVLDO l IMODE, IENBUCK, IENVLDO Input Pin Current l Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3541 is guaranteed to meet performance specifications from 0°C to 85°C. VLDO/linear regulator output is tested and specified under pulse load conditions such that TJ ≈ TA, and are 100% production tested at 25°C. Specifications over the –40°C to 85°C operating temperature range are assured by design, characterization and correlation with statistical process controls. Note 3: Minimum operating LVIN voltage required for VLDO regulator regulation is: LVIN ≥ LVOUT + VDROPOUT and LVIN ≥ 0.9V Note 4: Minimum operating VIN voltage required for VLDO regulator and linear regulator regulation is: VIN ≥ LVOUT + 1.4V and VIN ≥ 2.7V Note 5: TJ is calculated from the ambient temperature, TA, and power dissipation, PD, according to the following formula: TJ = TA + (PD • 43°C/W) 1.8 2.25 ±0.01 l 2.7 ±1 0.9 MHz µA V ±0.01 0.3 V ±1 µA Note 6: The LTC3541 is tested in a proprietary test mode that connects VBUCKFB to the output of the error amplifier. For the reference regulation and line regulation tests, the output of the error amplifier is set to the midpoint. For the load regulation test, the output of the error amplifier is driven to minimum and maximum of the signal range. Note 7: Measurement made in closed loop linear regulator configuration with LVOUT = 1.2V, ILOAD = 10µA. Note 8: Measurement made in a proprietary test mode with slope compensation disabled. Note 9: Measurement is assured by design, characterization and statistical process control. Note 10: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. Junction temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability. 3541fa LTC3541 TYPICAL PERFOR A CE CHARACTERISTICS U W Efficiency vs Input Voltage for Buck (Burst) 100 VOUT = 1.8V 95 EFFICIENCY (%) EFFICIENCY (%) IOUT = 100mA 80 90 IOUT = 500mA 90 IOUT = 500mA 85 100 VOUT = 1.8V 95 90 IOUT = 30mA 75 70 65 85 80 75 IOUT = 100mA 70 IOUT = 30mA 65 50 40 30 20 55 10 50 6 4 5 INPUT VOLTAGE (V) 2 Efficiency vs Load Current for Buck (Burst) 100 VIN = 2.7V VIN = 3.6V 80 80 EFFIcIENcY (%) 70 60 50 40 60 50 40 30 20 20 10 10 1 10 100 LOAD CURRENT (mA) VIN = 3.6V 250 VOUT = 1.5V VIN = 3V 200 BIAS CURRENT (µA) 60 VIN = 4.2V 40 1 10 100 LOAD cURRENT (mA) 1000 0 50 100 150 200 LOAD CURRENT (mA) 250 300 3541 G07 VIN = 4.2V 60 50 40 30 0 0.1 1 10 100 LOAD CURRENT (mA) VIN = 3.6V ILOAD(BUCK) = 0 IBIAS = IVIN + ILVIN – ILOAD 3541 G06 VOUT 2V/DIV 150 LVOUT 2V/DIV 100 VIN 2V/DIV 0 0.1 IVOUT = 300mA ILVOUT = 200mA 1 10 100 LOAD CURRENT (mA) 1000 Output (Auto Start-Up Sequence, Buck in Pulse Skip) vs Time 50 20 0 70 Buck (Burst) Plus VLDO Bias Current vs VLDO Load Current VIN = 3.6V VIN = 3.6V 3541 G05 VLDO Dropout Voltage vs Load Current 80 VIN = 2.7V 80 10 VOUT = 2.5V 3541 G04 100 VOUT = 2.5V 20 0 0.1 1000 90 VIN = 4.2V 70 30 0 0.1 100 VIN = 2.7V 90 VIN = 4.2V Efficiency vs Load Current for Buck (Pulse Skip) EFFICIENCY (%) VOUT = 1.8V 90 1000 3541 G03 3541 G02 Efficiency vs Load Current for Buck (Pulse Skip) 100 VOUT = 1.8V 0 0.1 1 10 100 LOAD CURRENT (mA) 6 4 5 INPUT VOLTAGE (V) 3 3541 G01 DROPOUT VOLTAGE (mV) 60 55 3 VIN = 4.2V VIN = 3.6V 70 60 2 VIN = 2.7V 80 60 50 EFFICIENCY (%) Efficiency vs Load Current for Buck (Burst) EFFICIENCY (%) 100 Efficiency vs Input Voltage for Buck (Pulse Skip) 2ms/DIV 3541 G09 1000 3541 G08 3541fa LTC3541 TYPICAL PERFOR A CE CHARACTERISTICS U W Oscillator Frequency vs Temperature 2.45 2.5 VIN = 3.6V 0.410 VIN = 3.6V 0.408 2.30 2.25 2.20 2.15 2.10 2.3 2.2 50 25 0 75 TEMPERATURE (°C) 2.0 125 100 5 4 SUPPLY VOLTAGE (V) 3 3541 G10 0.400 0.398 0.396 6 0.390 –50 –25 50 25 0 75 TEMPERATURE (°C) 125 100 5341 G12 3541 G11 Buck Reference vs Temperature Buck (Burst) and VLDO Output RDS(ON) vs Temperature 0.700 VIN = 3.6V LVOUT 10mV/DIV AC COUPLED 0.600 0.812 0.500 0.808 0.804 RDS(ON) (Ω) REFERENCE (V) 0.402 0.392 2.00 –50 –25 0.816 0.404 0.394 2.1 2.05 0.820 VIN = 3.6V 0.406 2.4 2.35 FREQUENCY (MHz) FREQUENCY (MHz) 2.40 VLDO/Linear Regulator Reference vs Temperature REFERENCE (V) 2.50 Oscillator Frequency vs Supply Voltage 0.400 0.800 VOUT 10mV/DIV AC COUPLED SYNCH SWITCH 0.300 0.796 0.792 0.200 0.788 0.100 0.784 0.780 –50 –25 50 25 0 75 TEMPERATURE (°C) 100 125 MAIN SWITCH 0 –50 –25 50 25 75 0 TEMPERATURE (°C) 5341 G13 125 Buck (Burst) Load Step from 1mA to 500mA VOUT 100mV/DIV AC COUPLED VOUT 100mV/DIV AC COUPLED IL 500mA/DIV IL 500mA/DIV ILOAD 500mA/DIV ILOAD 500mA/DIV 3541 G16 100 2µs/DIV VIN = 3.6V LVOUT = 1.5V VOUT = 1.8V ILOAD = 50mA Burst Mode OPERATION 3541 G15 3541 G14 Buck (Pulse Skip) Load Step from 1mA to 500mA 40µs/DIV VIN = 3.6V VOUT = 1.8V ILOAD = 1mA TO 500mA VIN = 2.5V VIN = 3.6V VIN = 5.5V VLDO Load Step from 1mA to 500mA LVOUT 20mV/DIV AC COUPLED ILOAD 250mA/DIV 40µs/DIV VIN = 3.6V VOUT = 1.8V ILOAD = 1mA TO 500mA 3541 G17 400µs/DIV VIN = 3.6V LVOUT = 1.5V ILOAD = 1mA TO 300mA 3541 G18 3541fa LTC3541 TYPICAL PERFOR A CE CHARACTERISTICS U W VLDO Load Step from 100mA to 300mA Linear Regulator to VLDO Transient Step, Load = 1mA LVOUT 20mV/DIV AC COUPLED LVOUT 10mV/DIV AC COUPLED ILOAD 250mA/DIV ILOAD 50mA/DIV 400µs/DIV VIN = 3.6V LVOUT = 1.5V ILOAD = 100mA TO 300mA 3541 G19 Linear Regulator to VLDO Transient Step, Load = 30mA LVOUT 10mV/DIV AC COUPLED ILOAD 50mA/DIV VIN = 3.6V LVOUT = 1.5V ILOAD = 1mA 40µs/DIV VLDO to Linear Regulator Transient Step, Load = 1mA 3541 G20 VIN = 3.6V LVOUT = 1.5V ILOAD = 30mA 40µs/DIV 3541 G21 VLDO to Linear Regulator Transient Step, Load = 30mA LVOUT 10mV/DIV AC COUPLED LVOUT 10mV/DIV AC COUPLED ILOAD 50mA/DIV ILOAD 50mA/DIV VIN = 3.6V LVOUT = 1.5V ILOAD = 1mA 40µs/DIV 3541 G22 VIN = 3.6V LVOUT = 1.5V ILOAD = 30mA 40µs/DIV 3541 G23 3541fa LTC3541 PI FU CTIO S U U U VIN (Pin 1): Main Supply Pin. This pin must be closely decoupled to GND with a 10µF or greater capacitor. ENBUCK (Pin 2): Buck Enable Pin. This pin enables the buck regulator when driven to a logic high. BUCKFB (Pin 3): Buck Regulator Feedback Pin. This pin receives the buck regulator’s feedback voltage from an external resistive divider. LFB (Pin 4): VLDO/Linear Regulator Feedback Pin. This pin receives either the VLDO or linear regulator’s feedback voltage from an external resistive divider. LVOUT (Pin 5): VLDO/Linear Regulator Output Pin. This pin provides the regulated output voltage from the VLDO or linear regulator. LVIN (Pin 6): VLDO/Linear Regulator Input Supply Pin. This pin provides the input supply voltage for the VLDO power FET. GND (Pin 7): Analog Ground Pin. MODE (Pin 8): Buck Mode Selection Pin. This pin enables buck Pulse-Skip operation when driven to a logic high and enables buck Burst Mode operation when driven to a logic low. ENVLDO (Pin 9): VLDO/Linear Regulator Enable Pin. When driven to a logic high, this pin enables the linear regulator when the ENBUCK pin is driven to a logic low, and enables the VLDO when the ENBUCK pin is driven to a logic high. SW (Pin 10): Switch Node Pin. This pin connects the internal main and synchronous power MOSFET switches to the external inductor for the buck regulator. Exposed Pad (Pin 11): Ground Pin. This pin must be soldered to the PCB to provide both electrical contact to ground and good thermal contact to the PCB. Note: Table 1 details the truth table for the control pins of the LTC3541. Table 1. LTC3541 Control Pin Truth Table PIN NAME OPERATIONAL DESCRIPTION ENBUCK ENVLDO MODE 0 0 X LTC3541 Powered Down 0 1 X Buck Powered Down, VLDO Regulator Powered Down, Linear Regulator Enabled 1 0 0 Buck Enabled, VLDO Regulator Powered Down, Linear Regulator Powered Down, Burst Mode Operation 1 0 1 Buck Enabled, VLDO Regulator Powered Down, Linear Regulator Powered Down, Pulse-Skip Mode Operation 1 1 0 Buck Enabled, VLDO Regulator Enabled, Linear Regulator Powered Down, Burst Mode Operation 1 1 1 Buck Enabled, VLDO Regulator Enabled, Linear Regulator Powered Down, PulseSkip Mode Operation 3541fa LTC3541 FU CTIO AL BLOCK DIAGRA W U U 2.2µH IOUT(BUCK) = 500mA VIN(MIN) ≥ LVOUT + 1.4V 10µF 10 1 SW VIN 500mA BUCK VIN SW 22pF REF FB GND BUCKFB LVIN VLDO/LINEAR REG 2 9 8 REF ENBUCK ENVLDO MODE 3 PGND REF CONTROL LOGIC LFB CNTRL VIN 6 LVIN LVOUT(MAX) < VIN – 1.4V IOUT = 300mA (VLDO REG) IOUT = 30mA (LINEAR REG) + – LVOUT 5 GND 2.2µF LFB GND PGND 7 11 4 3541 F01 Figure 1. LTC3541 Functional Block Diagram U OPERATIO The LTC3541 contains a high efficiency synchronous buck converter, a very low dropout regulator (VLDO) and a linear regulator. It can be used to provide up to two output voltages from a single input voltage making the LTC3541 ideal for applications with limited board space. The combination and configuration of these major blocks within the LTC3541 is determined by way of the control pins ENBUCK and ENVLDO as defined in Table 1. With the ENBUCK pin driven to a logic high and ENVLDO driven to a logic low, the LTC3541 enables the buck converter to efficiently reduce the voltage provided at the VIN input pin to an output voltage which is set by an external feedback resistor network. The buck regulator can be configured for Pulse-Skip or Burst Mode operation by driving the MODE pin to a logic high or logic low respectively. The buck regulator is capable of providing a maximum output current of 500mA, which must be taken into consideration when using the buck regulator to provide the power for both the VLDO and for external loads. With the ENBUCK pin driven to a logic low and ENVLDO driven to a logic high, the LTC3541 enables the linear regulator, providing a low noise regulated output voltage at the LVOUT pin while drawing minimal quiescent current from the VIN input pin. This feature allows output voltage LVOUT to be brought into regulation without the presence of the LVIN voltage. With the ENBUCK and ENVLDO pins both driven to a logic high, the LTC3541 enables the high efficiency buck converter and VLDO regulator, providing dual output operation from a single input voltage. When configured in this manner, the LTC3541’s auto start-up sequencing feature will bring the buck output into regulation in a controlled manner prior to enabling the VLDO regulator without the 3541fa LTC3541 U OPERATIO need for external pin control. A detailed discussion of the transitions between the VLDO and linear regulator can be found in the VLDO/Linear Regulator Loop section. Buck Regulator Control Loop The LTC3541 internal buck regulator uses a constant frequency, current mode, step-down architecture. Both the main (top, P-channel MOSFET) and synchronous (bottom, N-channel MOSFET) switches are internal. During normal operation, the internal main switch is turned on at the beginning of each clock cycle provided the internal feedback voltage to the buck is less than the reference voltage. The current into the inductor provided to the load increases until the current limit is reached. Once the current limit is reached the main switch turns off and the energy stored in the inductor flows through the bottom synchronous switch into the load until the next clock cycle. When the MODE pin is driven to a logic high the LTC3541 operates in Pulse-Skip mode for low output voltage ripple. In this mode, the LTC3541 continues to switch at a constant frequency down to very low currents, where it will begin skipping pulses used to control the main (top) switch to maintain the proper average inductor current. If the input supply voltage is decreased to a value approaching the output voltage, the duty cycle of the buck is increased toward maximum on-time and 100% duty cycle. The output voltage will then be determined by the input voltage minus the voltage drop across the main switch and the inductor. VLDO/Linear Regulator Loop The peak inductor current is determined by comparing the buck feedback signal to an internal 0.8V reference. When the load current increases, the output of the buck and hence the buck feedback signal decrease. This decrease causes the peak inductor current to increase until the average inductor current matches the load current. While the main switch is off, the synchronous switch is turned on until either the inductor current starts to reverse direction or the beginning of a new clock cycle. In the LTC3541, the VLDO and linear regulator loops consist of an amplifier and N-channel MOSFET output stages that, when connected with the proper external components, will servo the output to maintain a regulator output voltage, LVOUT. The internal reference voltage provided to the amplifier is 0.4V allowing for a wide range of output voltages. Loop configurations enabling the VLDO or the linear regulator are stable with an output capacitance as low as 2.2µF and as high as 100µF. Both the VLDO and the linear regulators are capable of operating with an input voltage, VIN, as low as 2.7V, but are subject to the constraint that VIN must be greater than LVOUT + 1.4V. When the MODE pin is driven to a logic low, the LTC3541 buck regulator operates in Burst Mode operation for high efficiency. In this mode, the main switch operates based upon load demand. In Burst Mode operation the peak inductor current is set to a fixed value, where each burst event can last from a few clock cycles at light loads to nearly continuous cycling at moderate loads. Between burst events the main switch and any unneeded circuitry are turned off, reducing the quiescent current. In this sleep state, the load is being supplied solely from the output capacitor. As the output voltage droops, an internal error amplifier’s output rises until a wake threshold is reached causing the main switch to again turn on. This process repeats at a rate that is dependant upon the load current demand. The VLDO is designed to provide up to 300mA of output current at a very low LVIN to LVOUT voltage. This allows a clean, secondary, analog supply voltage to be provided with a minimum drop in efficiency. The VLDO is provided with thermal protection that is designed to disable the VLDO function when the output, pass transistor’s junction temperature reaches approximately 160°C. In addition to thermal protection, short-circuit detection is provided to disable the VLDO function when a short-circuit condition is sensed. This circuit is designed such that an output current of approximately 1A can be provided before this circuit will trigger. As detailed in the Electrical Characteristics, the VLDO regulator will be out of regulation when this event occurs. Both the thermal and short-circuit faults when detected are treated as catastrophic fault conditions. The 3541fa LTC3541 U OPERATIO LTC3541 will be reset upon the detection of either event. The N-channel MOSFET incorporated in the VLDO has its drain connected to the LVIN pin as shown in Figure 1. To ensure reliable operation, the LVIN voltage must be stable before the VLDO is enabled. For the case where the voltage on the LVIN pin is supplied by the buck regulator, the internal power supply sequencing logic assures voltages are applied in the appropriate manner. For the case where an external supply is used to power the LVIN pin, the voltage on the LVIN pin must be stable before the ENVLDO pin is brought from a low to a high. Further, the external LVIN voltage must be reduced in conjunction with VIN whenever VIN is pulled low or removed. The linear regulator is designed to provide a lower output current (30mA) than that available from the VLDO. The linear regulator’s output pass transistor has its drain tied to the VIN rail. This allows the linear regulator to be turned on prior to, and independent of, the buck regulator which ordinarily drives the VLDO. The linear regulator is provided with thermal protection that is designed to disable the linear regulator function when the output pass transistor’s junction temperature reaches approximately 160°C. In addition to thermal protection, short-circuit detection is provided to disable the linear regulator function when a short-circuit condition is sensed. This circuit is designed such that an output current of approximately 120mA can be provided before this circuit will trigger. As detailed in the Electrical Characteristics, the linear regulator will be out of regulation when this event occurs. Both the thermal and short-circuit faults are treated as catastrophic fault conditions. The LTC3541 will be reset upon the detection of either event. The N-channel MOSFET incorporated in the linear regulator has its drain connected to the VIN pin as shown in Figure 1. The size of this MOSFET and its associated power bussing is designed to accommodate 30mA of DC current. Currents above this can be supported for short periods as stipulated in the Absolute Maximum Ratings section. Transitioning from linear regulator mode to VLDO mode, accomplished by bringing ENBUCK from a logic low to a logic high while ENVLDO is a logic high, is designed to be as seamless and transient free as possible. The precise transient response of LVOUT due to this transition is a function of COUT and the load current. Waveforms given in the Typical Performance Characeristics show typical transient responses using the minimum COUT of 2.2µF and load currents of 1mA and 30mA respectively. Generally, the amplitude of any transients present will decrease as COUT is increased. To ensure reliable operation and adherence to the load regulation limits presented in the Electrical Characteristics table, the load current must not exceed the linear regulator IOUT limit of 30mA within 20ms after ENBUCK has transitioned to a logic high. The 300mA IOUT limit of VLDO applies thereafter. Further, for configurations that do not use the LTC3541’s buck regulator to provide the VLDO input voltage (LVIN), the user must ensure a stable LVIN voltage is present no less than 1ms prior to ENBUCK transitioning to a logic high. In a similar manner, transitioning from VLDO mode to linear regulator mode, accomplished by bringing ENBUCK from a high low to a logic low while ENVLDO is a logic high, is designed to be as seamless and transient free as possible. Again, the precise transient response of LVOUT due to this transition is a function of COUT and the load current. Waveforms given in the Typical Performance Characeristics show typical transient responses using the minimum COUT of 2.2µF and load currents of 1mA and 30mA respectively. Generally, the amplitude of any transients present will decrease as COUT is increased. To ensure reliable operation and adherence to the load regulation limits presented in the Electrical Characterstics table, the load current must not exceed the linear regulator IOUT limit of 30mA 1ms prior to ENBUCK transitioning to a logic low and thereafer. Further, for configurations that do not use the LTC3541’s buck regulator to provide the VLDO input voltage (LVIN), the user must continue to ensure a stable LVIN voltage no less than 1ms after ENBUCK has transitioned to a logic low. 3541fa 10 LTC3541 APPLICATIO S I FOR ATIO U U W U The basic LTC3541 application circuit is shown on the first page of this data sheet. External component selection is driven by the load requirement and requires the selection of L, followed by CIN, COUT, and feedback resistor values for the buck and the selection of the output capacitor and feedback values for the VLDO and linear regulator. BUCK Regulator Inductor Selection For most applications, the appropriate inductor value will be in the range of 1.5µH to 3.3µH with 2.2µH the most commonly used. The exact inductor value is chosen largely based on the desired ripple current and burst ripple performance. Generally, large value inductors reduce ripple current, and conversely, small value inductors produce higher ripple current. Higher VIN or VOUT may also increase the ripple current as shown in Equation 1. A reasonable starting point for setting ripple current is ΔIL = 200mA (40% of 500mA). ΔIL = V 1 VOUT 1− OUT VIN ( f )(L ) (1) The DC current rating of the inductor should be at least equal to the maximum load current plus half the ripple current to prevent core saturation. Thus, a 600mA rated inductor should be enough for most applications (500mA + 100mA). For better efficiency, choose a low DC resistance inductor. Inductor Core Selection Different core materials and shapes will change the size/current and price/current relationship of an inductor. Toroid or shielded pot cores in ferrite or permalloy materials are small and don’t radiate much energy, but generally cost more than powdered iron core inductors with similar electrical characteristics. The choice of which style inductor to use often depends more on the price vs size requirement and any radiated field/EMI requirements rather than what the LTC3541 requires to operate. Table 2 shows some typical surface mount inductors that work well in LTC3541 applications. Table 2. Representative Surface Mount Inductors PART NUMBER VALUE (µH) DCR MAX DC (Ω MAX) CURRENT (A) SIZE W × L × H (mm3) Sumida CDRH3D23 1.0 1.5 2.2 3.3 0.025 0.029 0.038 0.048 2.0 1.5 1.3 1.1 3.9 × 3.9 × 2.4 Sumida CMD4D06 2.2 3.3 0.116 0.174 0.950 0.770 3.5 × 4.3 × 0.8 Coilcraft ME3220 1.0 1.5 2.2 3.3 0.058 0.068 0.104 0.138 2.7 2.2 1.0 1.3 2.5 × 3.2 × 2.0 Murata LQH3C 1.0 2.2 0.060 0.097 1.00 0.79 2.5 × 3.2 × 2.0 Sumida CDRH2D11/HP 1.5 2.2 0.06 0.10 1.00 0.72 3.2 × 3.2 × 1.2 CIN and COUT Selection In continuous mode, the source current of the top MOSFET is a square wave of duty cycle VOUT/VIN. To prevent large voltage transients, a low ESR input capacitor sized for the maximum RMS current must be used. The maximum RMS capacitor current is given by: cIN required IRMS ≅ IOMAX VOUT ( VIN − VOUT ) VIN 1/22 This formula has a maximum at VIN = 2VOUT, where IRMS = IOUT/2. This simple worst-case condition is commonly used for design. Note that the capacitor manufacturer’s ripple current ratings are often based on 2000 hours of life. This makes it advisable to further derate the capacitor or choose a capacitor rated at a higher temperature than required. Always consult the manufacturer with any question regarding proper capacitor choice. The selection of COUT for the buck regulator is driven by the desired buck loop transient response, required effective series resistance (ESR) and burst ripple performance. The LTC3541 minimizes the required number of external components by providing internal loop compensation for the buck regulator loop. Loop stability, transient response and burst performance can be tailored by choice of output capacitance. For many applications, desirable stability, transient response and ripple performance can 3541fa 11 LTC3541 APPLICATIO S I FOR ATIO U U W U be obtained by choosing an output capacitor value of 10µF to 22µF. Typically, once the ESR requirement for COUT has been met, the RMS current rating generally far exceeds the IRIPPLE(P-P) requirement. The output ripple ΔVOUT is determined by: 1 ΔVOUT ≅ ΔIL ESR + 8 fc OUT where f = operating frequency, COUT = output capacitance and ΔIL = ripple current in the inductor. For a fixed output voltage, the output ripple is highest at maximum input voltage since ΔIL increases with input voltage. Aluminum electrolytic and dry tantalum capacitors are both available in surface mount configurations. In the case of tantalum, it is critical that the capacitors are surge tested for use in switching power supplies. An excellent choice is the AVX TPS series of surface mount tantalum. These are specially constructed and tested for low ESR so they give the lowest ESR for a given volume. Other capacitor types include Sanyo POSCAP, Kemet T510 and T495 series, and Sprague 593D and 595D series. Consult the manufacturer for other specific recommendations. Using Ceramic Input and Output Capacitors High value, low cost ceramic capacitors are now becoming available in smaller case sizes. Their high ripple current, high voltage rating, and low ESR make them ideal for switching regulator applications. Since the LTC3541’s control loop does not depend on the output capacitor’s ESR for stable operation, ceramic capacitors can be used freely to achieve very low output ripple and small circuit size. However, care must be taken when ceramic capacitors are used at the input and the output. When a ceramic capacitor is used at the input and the power is supplied by a wall adapter through long wires, a load step at the output can induce ringing at the input, VIN. At best, this ringing can couple to the output and be mistaken as loop instability. At worst, a sudden inrush of current through the long wires can potentially cause a voltage spike at VIN, large enough to damage the part. When choosing the input and output ceramic capacitors, choose the X5R or X7R dielectric formulations. These dielectrics have the best temperature and voltage characteristics of all the ceramics for a given value and size. Output Voltage Programming The output voltage is set by tying BUCKFB to a resistive divider according to the following formula: R2 VOUT = 0.8 V 1+ R1 Since the impedance at the BUCKFB pin is dependant upon the resistor divider network used, and phase shift due to this impedance directly impacts the transient response of the buck, R1 should be chosen <125k. In addition, stray capacitance at this pin should be minimized (<5pF) to prevent excessive phase shift. Finally, special attention should be given to any stray capacitances that can couple external signals onto the BUCKFB pin producing undesirable output ripple. For optimum performance connect the BUCKFB pin to R1 and R2 with a short PCB trace and minimize all other stray capacitance to the BUCKFB pin. The external resistive divider is connected to the output, allowing remote voltage sensing as shown in Figure 6. Checking Transient Response The regulator loop response can be checked by looking at the load transient response. Switching regulators take several cycles to respond to a step in load current. When a load step occurs, VOUT immediately shifts by an amount equal to (ΔILOAD • ESR), where ESR is the effective series 0.8V ≤ VOUT ≤ 5V R2 BUcKFB LTc3541 R1 GND 3541 F06 Figure 6. Setting the LTC3541 Output Voltage 3541fa 12 LTC3541 APPLICATIO S I FOR ATIO U W U U resistance of COUT. ΔILOAD also begins to charge or discharge COUT, which generates a feedback error signal. The regulator loop then acts to return VOUT to its steady-state value. During this recovery time VOUT can be monitored for overshoot or ringing that would indicate a stability problem. For a detailed explanation of switching control loop theory see Application Note 76. A second, more severe transient is caused by switching in loads with large (>1µF) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT. No regulator can deliver enough current to prevent this problem if the load switch resistance is low and it is driven quickly. The only solution is to limit the rise time of the switch drive so that the load rise time is limited to approximately (25 • CLOAD). Thus, a 10µF capacitor charging to 3.3V would require a 250µs rise time, limiting the charging current to about 130mA. VLDO/Linear regulator Adjustable Output Voltage The LTC3541 LVOUT output voltage is set by the ratio of two external resistors as shown in Figure 7. The device servos LVOUT to maintain the LFB pin voltage at 0.4V (referenced to ground). Thus, the current in R1 is equal to 0.4V/R1. For good transient response, stability, and accuracy, the current in R1 should be at least 2µA, thus the value of R1 should be no greater than 200k. The current in R2 is the current in R1 plus the LFB pin bias current. Since the LFB pin bias current is typically <10nA, it can be ignored in the output voltage calculation. The output voltage can be calculated using the formula in Figure 8. Note that in shutdown the output is turned off and the divider current will be zero once COUT is discharged. The LTC3541 VLDO and linear regulator loops operate at a relatively high gain of –3.5µV/mA and –3.4µV/mA respectively, referred to the LFB input. Thus, a load current change of 1mA to 300mA produces a 1.05mV drop at the LFB input for the VLDO and a load current change of 1mA to 30mA produces a 0.1mV drop at the LFB input LVOUT LTc3541 R2 LFB ( ) VOUT = 0.4V 1 + R2 R1 cOUT R1 GND 3541 F07 Figure 7. Programming the LTC3541 for the linear regulator. To calculate the change referred to the output simply multiply by the gain of the feedback network (i.e., 1 + R2/R1). For example, to program the output for 1.2V choose R2/R1 = 2. In this example, an output current change of 1mA to 300mA produces 1.05mV • (1 + 2) = 3.15mV drop at the output. Since the LFB pin is relatively high impedance (depending on the resistor divider used), stray capacitance at this pin should be minimized (<10pF) to prevent phase shift in the error amplifier loop. Additionally, special attention should be given to any stray capacitances that can couple external signals onto the LFB pin producing undesirable output ripple. For optimum performance connect the LFB pin to R1 and R2 with a short PCB trace and minimize all other stray capacitance to the LFB pin. Output Capacitance and Transient Response The LTC3541 is designed to be stable with a wide range of ceramic output capacitors. The ESR of the output capacitor affects stability, most notably with small capacitors. A minimum output capacitor of 2.2µF with an ESR of 0.05Ω or less is recommended to ensure stability. The LTC3541 VLDO is a micropower device and output transient response will be a function of output capacitance. Larger values of output capacitance decrease the peak deviations and provide improved transient response for larger load current changes. Note that bypass capacitors used to decouple individual components powered by the LTC3541 will increase the effective output capacitor value. High ESR tantalum and electrolytic capacitors may be used, but a low ESR ceramic capacitor must be in parallel at the output. There is no minimum ESR or maximum capacitor size requirement. 3541fa 13 LTC3541 APPLICATIO S I FOR ATIO U U W U Extra consideration must be given to the use of ceramic capacitors. Ceramic capacitors are manufactured with a variety of dielectrics, each with different behavior across temperature and applied voltage. The most common dielectrics used are Z5U, Y5V, X5R and X7R. The Z5U and Y5V dielectrics are good for providing high capacitances in a small package, but exhibit large voltage and temperature coefficients as shown in Figures 8 and 9. When used with a 2V regulator, a 1µF Y5V capacitor can lose as much as 75% of its initial capacitance over the operating temperature range. The X5R and X7R dielectrics result in more stable characteristics and are usually more suitable for use as the output capacitor. The X7R type has better stability across temperature, while the X5R is less 20 BOTH cAPAcITORS ARE 1µF, 10V, 0603 cASE SIZE cHANGE IN VALUE (%) 0 X5R –20 –40 Y5V –60 –80 –100 0 2 6 4 Dc BIAS VOLTAGE (V) 8 10 3541 F08 Figure 8. Change in Capacitor vs Bias Voltage 20 cHANGE IN VALUE (%) 0 X5R –20 Y5V –40 –60 –80 BOTH cAPAcITORS ARE 1µF, 10V, 0603 cASE SIZE –100 –50 0 25 50 –25 TEMPERATURE (°c) 75 3541 F09 Figure 9. Change in Capacitor vs Temperature expensive and is available in higher values. In all cases, the output capacitance should never drop below 1µF or instability or degraded performance may occur. EFFICIENCY CONSIDERATIONS Generally, the efficiency of a regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual loss terms to determine which terms are limiting efficiency and what if any change would yield the greatest improvement. Efficiency can be expressed as: Efficiency = 100% – (L1 + L2 + L3 + ...) where L1, L2, etc. are the individual loss terms as a percentage of input power. Although all dissipative elements in the circuit produce losses, three main sources typically account for the majority of the losses in the LTC3541 circuits: VIN quiescent current, I2R losses and loss across VLDO output device. When operating with both the buck and VLDO active (ENBUCK and ENVLDO equal to logic high), VIN quiescent current loss and loss across the VLDO output device dominate the efficiency loss at low load currents, whereas the I2R loss and loss across the VLDO output device dominate the efficiency loss at medium to high load currents. At low load currents with the part operating with the linear regulator (ENBUCK equal to logic low, ENVLDO equal to logic high), efficiency is typically dominated by the loss across the linear regulator output device and VIN quiescent current. In a typical efficiency plot, the efficiency curve at very low load currents can be misleading since the actual power lost is of little consequence. 1. The VIN quiescent current loss in the buck is due to two components: the DC bias current as given in the Electrical Characteristics and the internal main switch and synchronous switch gate charge currents. The gate charge current results from switching the gate capacitance of the internal power switches. Each time the gate is switched from high to low to high again, a packet of charge, dQ, moves from VIN to ground. The resulting dQ/dt is the current out of VIN that is typically larger than the DC bias current and 3541fa 14 LTC3541 APPLICATIO S I FOR ATIO U W U U proportional to frequency. Both the DC bias and gate charge losses are proportional to VIN and thus their effects will be more pronounced at higher supply voltages. 2. I2R losses are calculated from the resistances of the internal switches, RSW, and external inductor RL. In continuous mode, the average output current flowing through inductor L is “chopped” between the main switch and the synchronous switch. Thus, the series resistance looking into the SW pin is a function of both top and bottom MOSFET RDS(ON) and the duty cycle (DC) as follows: For surface mount devices, heat sinking is accomplished by using the heat-spreading capabilities of the PC board and its copper traces. Copper board stiffeners and plated through holes can also be used to spread the heat generated by power devices. To avoid the LTC3541 exceeding the maximum junction temperature, some thermal analysis is required. The goal of the thermal analysis is to determine whether the power dissipated exceeds the maximum junction temperature of the part. The temperature rise is given by: RSW = (RDS(ON)TOP)(DC) + (RDS(ON)BOT)(1 – DC) TR = PD • qJA The RDS(ON) for both the top and bottom MOSFETs can be obtained from the Typical Performance Characteristics curves. Thus, to obtain I2R losses, simply add RSW to RL and multiply the result by the square of the average output current. where PD is the power dissipated by the regulator and qJA is the thermal resistance from the junction of the die to the ambient temperature. 3. Losses in the VLDO/linear regulator are due to the DC bias currents as given in the Electrical Characteristics and to the (VIN – VOUT) voltage drop across the internal output device transistor. Other losses when the buck and VLDO are in operation (ENBUCK and ENVLDO equal logic high), including CIN and COUT ESR dissipative losses and inductor core losses, generally account for less than 2% total additional loss. THERMAL CONSIDERATIONS The LTC3541 requires the package backplane metal (GND pin) to be well soldered to the PC board. This gives the DFN package exceptional thermal properties. The power handling capability of the device will be limited by the maximum rated junction temperature of 125°C. The LTC3541 has internal thermal limiting designed to protect the device during momentary overload conditions. For continuous normal conditions, the maximum junction temperature rating of 125°C must not be exceeded. It is important to give careful consideration to all sources of thermal resistance from junction to ambient. Additional heat sources mounted nearby must also be considered. The junction temperature, TJ, is given by: TJ = TA + TR where TA is the ambient temperature. As an example, consider the LTC3541 with an input voltage VIN of 2.9V, an LVIN voltage of 1.8V, an LVOUT voltage of 1.5V, a load current of 200mA for the buck, a load current of 300mA for the VLDO and an ambient temperature of 85°C. From the typical performance graph of switch resistance, the RDS(ON) of the P-channel switch at 85°C is approximately 0.25Ω.The RDS(ON) of the N-channel switch is approximately 0.4Ω. Therefore, power dissipated by the part is approximately: PD = (ILOADBUCK)2 • RSW + (ILOADVLDO) • (LVIN – LVOUT) = 167mW For the 3mm × 3mm DFN package, the qJA is 43°C/W. Thus, the junction temperature of the regulator is: TJ = 85°C + (0.167)(43) = 92°C which is well below the maximum junction temperature of 125°C. Note that at higher supply voltages, the junction temperature is lower due to reduced switch resistance RDS(ON). 3541fa 15 LTC3541 APPLICATIO S I FOR ATIO U W U U PC BOARD LAYOUT CHECKLIST When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the LTC3541. Check the following in your layout: 1. The power traces, consisting of the GND trace, the SW trace and the VIN trace should be kept short, direct and wide. 2. Does the LFB pin connect directly to the feedback resistors? The resistive divider R1/R2 must be connected between the (+) plate of COUT and ground. ing up to 0.3A of current. With this information we can calculate L using Equation 2: L= V 1 VOUT 1− OUT VIN ( f )( ΔIL ) (2) Substituting VOUT = 1.8V, VIN = 3.6V (typ), ΔIL = 0.2A and f = 2.25MHz in Equation 3 gives: L= 1.8 V 1.8 V 1− = 2 µH 2.25MHz(200mA) 3.6 V (3) 3. Does the (+) plate of CIN connect to VIN as closely as possible? This capacitor provides the AC current to the internal power MOSFETs. A 2.2µH inductor works well for this application. For best efficiency choose a 600mA or greater inductor with less than 0.2Ω series resistance. 4. Keep the switching node, SW, away from the sensitive LFB node. CIN will require an RMS current rating of at least 0.25A = ILOAD(MAX)/2 at temperature . COUT for the buck is chosen as 22µF with an ESR of less than 0.2Ω. In most cases, a ceramic capacitor will satisfy this requirement. 5. Keep the (–) plates of CIN and COUT as close as possible. DESIGN EXAMPLE As a design example, assume the LTC3541 is used in a single lithium-ion battery powered cellular phone application. The VIN will be operating from a maximum of 4.2V down to about 3V. The load current requirement is a maximum of 0.5A for the buck output but most of the time it will be in standby mode, requiring only 2mA. Efficiency at both low and high load currents is important. The output voltage for the buck is 1.8V. The requirement for the output voltage of the VLDO is 1.5V while provid- For the feedback resistors of the buck, choose R1 = 80k. R2 can then be calculated from Equation 4 to be: V R2 = OUT − 1 R1= 100k 0.8 (4) For the feedback resistors of the VLDO, choose R1 = 200k. R2 can then be calculated from Equation 5 to be: V R2 = OUT − 1 R1= 550k 0.4 COUT for the VLDO is chosen as 2.2µF. 3541fa 16 LTC3541 TYPICAL APPLICATIO S U Dual Output with Minimal External Components Using Auto Start-Up Sequence, Buck in Burst Mode Operation for High Efficiency Down to Low Load Currents VIN 3.2V TO 4.2V 2.2µH VOUT 2V/DIV SW ENVLDO VIN MODE GND ENBUCK 22pF VOUT1 2.5V 200mA BUCKFB LVIN 10µF 165k LTC3541 154k 73k LVOUT 2V/DIV LFB 576k LVOUT PGND 2.2µF VOUT2 1.8V 300mA VIN 2V/DIV IVOUT = 200mA ILVOUT = 300mA 3541 TA02a 4ms/DIV 3541 TA02b 4ms/DIV 3541 TA03b Dual Output with Minimal External Components Using Auto Start-Up Sequence, Buck in Pulse Skip Mode for Low Noise Operation VIN 3.2V TO 4.2V 2.2µH VOUT 2V/DIV SW ENVLDO VIN MODE ENBUCK 22pF 154k VOUT1 2.5V 200mA 10µF LVIN 73k GND 165k LTC3541 BUCKFB LVOUT 2V/DIV LFB LVOUT PGND 576k 2.2µF 3541 TA03a VOUT2 1.8V 300mA VIN 2V/DIV IVOUT = 200mA ILVOUT = 300mA 3541fa 17 LTC3541 TYPICAL APPLICATIO S U Dual Output Using Minimal External Components with VOUT2 Controlled by External Logic Signal, Buck in Burst Mode Operation for High Efficiency Down to Low Load Currents VIN 3.2V TO 4.2V 2.2µH VOUT 2V/DIV SW ENVLDO VIN MODE ENBUCK 22pF VOUT1 2.5V 200mA BUCKFB 10µF GND 165k LTC3541 154k LVIN LFB LVOUT PGND 73k LVOUT 2V/DIV 576k 2.2µF VOUT2 1.8V 300mA VIN 2V/DIV IVOUT = 200mA ILVOUT = 300mA 3541 TA04a 4ms/DIV 3541 TA04b Dual Output Using Minimal External Components with VOUT1 Controlled by External Logic Signal, Buck in Burst Mode Operation for High Efficiency Down to Low Load Currents VIN 2.9V TO 4.2V VOUT 2V/DIV 2.2µH SW ENVLDO VIN MODE ENBUCK 22pF VOUT1 1.8V 200mA 143k 10µF LVIN 115k GND 150k LTC3541 BUCKFB LVOUT 2V/DIV LFB LVOUT PGND 412k 2.2µF 3541 TA05a VOUT2 1.5V 300mA VIN 2V/DIV IVOUT = 200mA ILVOUT = 30mA 4ms/DIV 3541 TA05b 3541fa 18 LTC3541 PACKAGE DESCRIPTIO U DD Package 10-Lead Plastic DFN (3mm × 3mm) (Reference LTC DWG # 05-08-1699) 0.675 ±0.05 3.50 ±0.05 1.65 ±0.05 2.15 ±0.05 (2 SIDES) PAcKAGE OUTLINE 0.25 ± 0.05 0.50 BSc 2.38 ±0.05 (2 SIDES) RECOMMENDED SOLDER PAD PITcH AND DIMENSIONS R = 0.115 TYP 6 3.00 ±0.10 (4 SIDES) 0.38 ± 0.10 10 1.65 ± 0.10 (2 SIDES) PIN 1 TOP MARK (SEE NOTE 6) 5 0.200 REF 1 0.75 ±0.05 0.00 – 0.05 (DD10) DFN 1103 0.25 ± 0.05 0.50 BSc 2.38 ±0.10 (2 SIDES) BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING TO BE MADE A JEDEc PAcKAGE OUTLINE M0-229 VARIATION OF (WEED-2). cHEcK THE LTc WEBSITE DATA SHEET FOR cURRENT STATUS OF VARIATION ASSIGNMENT 2. DRAWING NOT TO ScALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PAcKAGE DO NOT INcLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXcEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENcE FOR PIN 1 LOcATION ON THE TOP AND BOTTOM OF PAcKAGE 3541fa Information furnished by Linear Technology corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 19 LTC3541 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT 3023 Dual, 2x100mA, Low Noise Micropower LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 40µA, ISD < 1µA, VOUT = ADJ, DFN, MS Packages, Low Noise < 20µVRMS(P-P), Stable with 1µF Ceramic Capacitors LT3024 Dual, 100mA/500mA, Low Noise Micropower LDO VIN: 1.8V to 20V, VOUT(MIN) = 1.22V, VDO = 0.30V, IQ = 60µA, ISD < 1µA, VOUT = ADJ, DFN, TSSOP Packages, Low Noise < 20µVRMS(P-P), Stable with 1µF Ceramic Capacitors LTC3025 300mA, Micropower VLDO Linear Regulator VIN: 0.9V to 5.5V, VOUT(MIN) = 0.4V, 2.7V to 5.5V Bias Voltage Required, VDO = 45mV, IQ = 50µA, ISD < 1µA, VOUT = ADJ, DFN Packages, Stable with 1µF Ceramic Capacitors LTC3407 Dual Synchronous 600mA Synchronous Step-Down DC/DC Regulator 1.5MHz Constant Frequency Current Mode Operation, VIN from 2.5V to 5.5V, VOUT Down to 0.6V, DFN, MS Packages LTC3407-2 Dual Synchronous 800mA Synchronous Step-Down DC/DC Regulator, 2.25MHz 2.25MHz Constant Frequency Current Mode Operation, VIN from 2.5V to 5.5V, VOUT Down to 0.6V, DFN, MS Packages LTC3445 I2C Controllable Buck Regulator with Two LDOs and Backup Battery Input 600mA, 1.5MHz Current Mode Buck Regulator, I2C Programmable VOUT from 0.85V to 1.55V, two 50mA LDOs, Backup Battery Input with PowerPath Control, QFN Package LTC3446 Triple Output Step-Down Converter 1A Output Buck, Two Each 300mA VDLOs VIN: 2.7V to 5.5V, VOUT(MIN) Buck = 0.8V, VOUT(MIN) VLDO = 0.4VOUT(MIN), 14-Pin DFN Package LTC3448 600mA (IOUT), High Efficiency, 1.5MHz/2.25MHz Synchronous Step-Down Regulator with LDO Mode VIN: 2.7V to 5.5V, VOUT(MIN) = 0.6V, Switches to LDO Mode at ≤3A, DD8, MS8/E Packages LTC3541-2 High Efficiency Buck plus VLDO Regulator VIN: 2.9V to 5.5V, VOUT(BUCK) = 1.875V, VOUT(VLDO) = 1.5V, 3mm × 3mm 10-Pin DFN Package LTC3541-3 High Efficiency Buck plus VLDO Regulator VIN: 3V to 5.5V, VOUT(BUCK) = 1.8V, VOUT(VLDO) = 1.575V, 3mm × 3mm 10-Pin DFN Package LTC3547 Dual 300mA (IOUT), 2.25MHz, Synchronous Step-Down DC/DC Converter 95% Efficiency, VIN: 2.5V to 5.5V, VOUT(MIN) = 0.6V, IQ = 40µA, ISD < 1µA, 8-Pin DFN Package ® LTC3548/LTC3548-1 Dual 800mA/400mA (IOUT), 2.25MHz, Synchronous Step-Down DC/DC Converter LTC3548-2 95% Efficiency, VIN: 2.5V to 5.5V, VOUT(MIN) = 0.6V, IQ = 40µA, ISD < 1µA, DFN and 10-Pin MS Packages LTC3700 VIN from 2.65V to 9.8V, Constant Frequency 550kHz Operation Step-Down DC/DC Controller with LDO Regulator PowerPath is a trademark of Linear Technology Corporation. 3541fa 20 Linear Technology Corporation LT 0407 REV A • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2006