MAXIM MAX3301EEBA-T

19-3275; Rev 2; 1/06
USB On-the-Go Transceivers and Charge Pumps
Features
The MAX3301E/MAX3302E fully integrated USB On-theGo (OTG) transceivers and charge pumps allow mobile
devices such as PDAs, cellular phones, and digital
cameras to interface directly with USB peripherals and
each other without the need of a host PC. Use the
MAX3301E/MAX3302E with an embedded USB host to
directly connect to peripherals such as printers or
external hard drives.
The MAX3301E/MAX3302E integrate a USB OTG transceiver, a VBUS charge pump, a linear regulator, and an
I2C-compatible, 2-wire serial interface. An internal level
shifter allows the MAX3301E/MAX3302E to interface
with +1.65V to +3.6V logic supply voltages. The
MAX3301E/MAX3302E’s OTG-compliant charge pump
operates with +3V to +4.5V input supply voltages, and
supplies an OTG-compatible output on V BUS while
sourcing more than 8mA of output current.
The MAX3301E/MAX3302E enable USB OTG communication from highly integrated digital devices that cannot
supply or tolerate the +5V VBUS levels that USB OTG
requires. The device supports USB OTG session-request
protocol (SRP) and host-negotiation protocol (HNP).
The MAX3301E/MAX3302E provide built-in ±15kV electrostatic-discharge (ESD) protection for the VBUS, ID_IN,
D+, and D- terminals. The MAX3301E/MAX3302E are
available in 25-bump chip-scale (UCSP™), 28-pin TQFN,
and 32-pin TQFN packages and operate over the
extended -40°C to +85°C temperature range.
♦ USB 2.0-Compliant Full-/Low-Speed OTG
Transceivers
♦ Ideal for USB On-the-Go, Embedded Host, or
Peripheral Devices
♦ ±15kV ESD Protection on ID_IN, VBUS, D+, and DTerminals
♦ Charge Pump for VBUS Signaling and Operation
Down to 3V
♦ Internal VBUS and ID Comparators
♦ Internal Switchable Pullup and Pulldown
Resistors for Host/Peripheral Functionality
♦ I2C Bus Interface with Command and Status
Registers
♦ Linear Regulator Powers Internal Circuitry and
D+/D- Pullup Resistors
♦ Support SRP and HNP
Selector Guide
Note: All devices specified over the -40°C to +85°C operating
range.
‡UCSP bumps are in a 5 x 5 array. The UCSP package size is
2.5mm x 2.5mm x 0.62mm. Requires solder temperature profile
described in the Absolute Maximum Ratings section. UCSP reliability is integrally linked to the user’s assembly methods, circuit
board material and environment. See the UCSP Applications
Information section of this data sheet for more information.
*Future product—contact factory for availability.
**EP = Exposed paddle.
PART
POWER-UP STATE†
I2C ADDRESSES FOR
SPECIAL-FUNCTION
REGISTER 2
MAX3301E
Shutdown (sdwn = 1,
bit 0 of specialfunction register 2)
16h, 17h
MAX3302E
Operating (sdwn = 1,
bit 0 of specialfunction register 2)
10h, 11h, and 16h, 17h
†The
MAX3301E powers up in its lowest power state and the
MAX3302E powers up in the operational, VP/VM USB mode.
Applications
Mobile Phones
PDAs
Ordering Information
PART
MAX3301EEBA-T
MAX3301EETJ
MAX3302EEBA-T*
MAX3302EETI
PACKAGE
SIZE
(mm)
PINPACKAGE
PKG
CODE
2.5 x 2.5
25 UCSP‡
B25-1
5x5
2.5 x 2.5
4x4
32 TQFN-EP** T3255-4
25 UCSP‡
B25-1
28 TQFN-EP** T2844-1
Purchase of I2C components from Maxim Integrated Products,
Inc. or one of its sublicensed Associated Companies, conveys a
license under the Philips I2C Patent Rights to use these components in an I2C system, provided that the system conforms to the
I2C Standard Specification as defined by Philips.
UCSP is a trademark of Maxim Integrated Products, Inc.
Digital Cameras
MP3 Players
Pin Configurations appear at end of data sheet.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
1
MAX3301E/MAX3302E
General Description
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
ABSOLUTE MAXIMUM RATINGS
All voltages are referenced to GND.
VCC, VL .....................................................................-0.3V to +6V
TRM (regulator off or supplied by VBUS) ..-0.3V to (VBUS + 0.3V)
TRM (regulator supplied by VCC)...............-0.3V to (VCC + 0.3V)
D+, D- (transmitter tri-stated) ...................................-0.3V to +6V
D+, D- (transmitter functional)....................-0.3V to (VCC + 0.3V)
VBUS .........................................................................-0.3V to +6V
ID_IN, SCL, SDA.......................................................-0.3V to +6V
INT, SPD, RESET, ADD, OE/INT, RCV, VP,
VM, SUS, DAT_VP, SE0_VM ......................-0.3V to (VL + 0.3V)
C+.............................................................-0.3V to (VBUS + 0.3V)
C-................................................................-0.3V to (VCC + 0.3V)
Short-Circuit Duration, VBUS to GND .........................Continuous
Continuous Power Dissipation (TA = +70°C)
5 x 5 UCSP (derate 12.2mW/°C above +70°C) ...........976mW
32-Pin TQFN (5mm x 5mm x 0.8mm) (derate 21.3mW/°C
above +70°C).............................................................1702mW
28-Pin TQFN (4mm x 4mm x 0.8mm) (derate 20.8mW/°C
above +70°C).............................................................1666mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Bump Reflow Temperature (Note 1)
Infrared (15s) ...............................................................+200°C
Vapor Phase (20s) .......................................................+215°C
Note 1: The UCSP package is constructed using a unique set of packaging techniques that impose a limit on the thermal profile the
device can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder profiles recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and convection reflow. Preheating is
required. Hand or wave soldering is not allowed.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC ELECTRICAL CHARACTERISTICS
(VCC = +3V to +4.5V, VL = +1.65V to +3.6V, CFLYING = 100nF, CVBUS = 1µF, ESRCVBUS = 0.1Ω (max), TA = TMIN to TMAX, unless
otherwise noted. Typical values are at VCC = +3.7V, VL = +2.5V, TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
UNITS
4.5
V
VCC
TRM Output Voltage
VTRM
3.0
3.6
V
Logic Supply Voltage
VL
1.65
3.60
V
VL Supply Current
IVL
I2C interface in steady state
5
µA
VCC Operating Supply Current
ICC
USB normal mode, CL = 50pF, device
switching at full speed
10
mA
VCC Supply Current During FullSpeed Idle
3.0
MAX
Supply Voltage
vbus_drv = 1, IVBUS = 0
1.4
2
vbus_drv = 0, D+ = high, D- = low
0.5
0.8
mA
VCC Shutdown Supply Current
ICC(SHDN)
3.5
10
µA
VCC Interrupt Shutdown Supply
Current
ICC(ISHDN) ID_IN floating or high
20
30
µA
170
500
µA
VCC Suspend Supply Current
USB suspend mode, ID_IN floating or high
LOGIC I/O
RCV, DAT_VP, SE0_VM, INT,
OE/INT, VP, VM Output High
Voltage
VOH
IOUT = 1mA (sourcing)
RCV, DAT_VP, SE0_VM, INT,
OE/INT, VP, VM Output Low
Voltage
VOL
IOUT = 1mA (sinking)
OE/INT, SPD, SUS, RESET,
DAT_VP, SE0_VM Input High
Voltage
VIH
2
VL - 0.4
V
0.4
2/3 x VL
_______________________________________________________________________________________
V
V
USB On-the-Go Transceivers and Charge Pumps
(VCC = +3V to +4.5V, VL = +1.65V to +3.6V, CFLYING = 100nF, CVBUS = 1µF, ESRCVBUS = 0.1Ω (max), TA = TMIN to TMAX, unless
otherwise noted. Typical values are at VCC = +3.7V, VL = +2.5V, TA = +25°C.) (Note 2)
PARAMETER
OE/INT, SPD, SUS, RESET
DAT_VP, SE0_VM Input Low
Voltage
SYMBOL
CONDITIONS
MIN
TYP
VIL
ADD Input High Voltage
VIHA
ADD Input Low Voltage
VILA
MAX
UNITS
0.4
V
2/3 x VL
V
1/3 x VL
±1
Input Leakage Current
V
µA
TRANSCEIVER SPECIFICATIONS
Differential Receiver Input
Sensitivity
|VD+ - VD-|
0.2
Differential Receiver CommonMode Voltage
V
0.8
Single-Ended Receiver Input Low
Voltage
VILD
D+, D-
Single-Ended Receiver Input
High Voltage
VIHD
D+, D-
2.5
V
0.8
V
2.0
Single-Ended Receiver Hysteresis
V
0.2
Single-Ended Output Low Voltage
VOLD
D+, D-, RL = 1.5kΩ from D+ or D- to 3.6V
Single-Ended Output High Voltage
VOHD
D+, D-, RL = 15kΩ from D+ or D- to GND
Off-State Leakage Current
D+, D-
Driver Output Impedance
D+, D-, not
including REXT
Low steady-state drive
High steady-state drive
2.8
2
2
V
0.3
V
3.6
V
±1
µA
13
13
Ω
ESD PROTECTION (VBUS, ID_IN, D+, D-)
Human Body Model
±15
kV
IEC 61000-4-2 Air-Gap Discharge
±10
kV
IEC 61000-4-2 Contact Discharge
±6
kV
THERMAL SHUTDOWN
Thermal Shutdown Low-to-High
Thermal Shutdown High-to-Low
+160
o
C
+150
o
C
CHARGE-PUMP SPECIFICATIONS (vbus_drv = 1)
VBUS Output Voltage
VBUS
VBUS Output Current
IVBUS
VBUS Output Ripple
3V < VCC < 4.5V, CVBUS = 10µF, IVBUS = 8mA
4.80
5.25
8
IVBUS = 8mA, CVBUS = 10µF
V
mA
100
mV
_______________________________________________________________________________________
3
MAX3301E/MAX3302E
DC ELECTRICAL CHARACTERISTICS (continued)
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
DC ELECTRICAL CHARACTERISTICS (continued)
(VCC = +3V to +4.5V, VL = +1.65V to +3.6V, CFLYING = 100nF, CVBUS = 1µF, ESRCVBUS = 0.1Ω (max), TA = TMIN to TMAX, unless
otherwise noted. Typical values are at VCC = +3.7V, VL = +2.5V, TA = +25°C.) (Note 2)
PARAMETER
Switching Frequency
SYMBOL
CONDITIONS
MIN
fSW
TYP
MAX
390
UNITS
kHz
VBUS Leakage Voltage
vbus_drv = 0
0.2
V
VBUS Rise Time
CVBUS = 10µF, IVBUS = 8mA, measured
from 0 to +4.4V
100
ms
VBUS Pulldown Resistance
vbus_dischrg = 1, vbus_drv = 0, vbus_chrg = 0
3.8
5
6.5
kΩ
VBUS Pullup Resistance
vbus_chrg = 1, vbus_drv = 0, vbus_dischrg = 0
650
930
1250
Ω
vbus_dischrg = 0, vbus_drv = 0, vbus_chrg = 0
40
70
100
kΩ
4.4
4.6
4.8
V
VBUS Input Impedance
ZINVBUS
COMPARATOR SPECIFICATIONS
VBUS Valid Comparator Threshold
VTH-VBUS
VBUS Valid Comparator Hysteresis
VHYS-VBUS
Session-Valid Comparator
Threshold
SESS_VLD
Session-End Comparator
Threshold
VTHSESS_END
50
VTH-
mV
0.8
1.4
2.0
V
0.2
0.5
0.8
V
dp_hi Comparator Threshold
0.8
1.3
2.0
V
dm_hi Comparator Threshold
0.8
1.3
2.0
cr_int Pulse Width
750
cr_int Comparator Threshold
0.4
0.5
V
ns
0.6
V
0.8 x
VCC
V
0.1 x
VCC
V
ID_IN SPECIFICATIONS
0.2 x
VCC
ID_IN Input Voltage for Car Kit
ID_IN Input Voltage for A Device
0.9 x
VCC
ID_IN Input Voltage for B Device
ID_IN Input Impedance
ZID_IN
70
ID_IN Input Leakage Current
ID_IN = VCC
ID_IN Pulldown Resistance
id_pulldown = 1
V
100
130
kΩ
+1
µA
150
300
Ω
-1
TERMINATING RESISTOR SPECIFICATIONS (D+, D-)
D+ Pulldown Resistor
dp_pulldown = 1
14.25
15
15.75
kΩ
D- Pulldown Resistor
dm_pulldown = 1
14.25
15
15.75
kΩ
D+ Pullup Resistor
dp_pullup = 1
1.425
1.5
1.575
kΩ
D- Pullup Resistor
dm_pullup = 1
1.425
1.5
1.575
kΩ
4
_______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
(VCC = +3V to +4.5V, VL = +1.65V to +3.6V, CFLYING = 100nF, CVBUS = 1µF, ESRCVBUS = 0.1Ω (max), TA = TMIN to TMAX, unless
otherwise noted. Typical values are at VCC = +3.7V, VL = +2.5V, TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
TRANSMITTER CHARACTERISTICS (FULL-SPEED MODE)
D+, D- Rise Time
tR
Figures 2 and 5
4
20
ns
D+, D- Fall Time
tF
Figures 2 and 5
4
20
ns
Figures 2 and 5 (Note 3)
90
110
%
Figures 2, 6, and 7 (Note 3)
1.3
2.0
V
Rise-/Fall-Time Matching
Output-Signal Crossover Voltage
VCRS_F
TRANSMITTER CHARACTERISTICS (LOW-SPEED MODE)
D+, D- Rise Time
tR
Figures 2 and 5
75
300
ns
D+, D- Fall Time
tF
Figures 2 and 5
75
300
ns
Figures 2 and 5
80
125
%
Figures 2, 6, and 7
1.3
2.0
V
Rise-/Fall-Time Matching
Output-Signal Crossover Voltage
VCRS_L
TRANSMITTER TIMING (FULL-SPEED MODE)
Driver Propagation Delay
(DAT_VP, SE0_VM to D+, D-)
tPLH
Low-to-high, Figures 2 and 6
25
tPHL
High-to-low, Figures 2 and 6
25
Driver Disable Delay
tPDZ
Figures 1 and 8
25
ns
Driver Enable Delay
tPZD
Figures 2 and 8
25
ns
ns
TRANSMITTER TIMING (LOW-SPEED MODE) (Low-speed delay timing is dominated by the slow rise and fall times.)
SPEED-INDEPENDENT TIMING CHARACTERISTICS
Receiver Disable Delay
tPVZ
Receiver Enable Delay
tPZV
D+ Pullup Assertion Time
Figure 4
30
ns
Figure 4
30
ns
During HNP
3
µs
RCV Rise Time
tR
Figures 3 and 5, CL = 15pF
4
RCV Fall Time
tF
Figures 3 and 5, CL = 15pF
4
ns
ns
Figures 3 and 10, |D+ - D-| to DAT_VP
30
Figures 3 and 9, |D+ - D-| to RCV
30
Figures 3 and 9, D+, D- to DAT_VP,
SE0_VM
30
ns
100
µs
Time to Exit Shutdown
1
µs
Shutdown Delay
10
µs
Differential-Receiver Propagation
Delay
tPHL, tPLH
Single-Ended-Receiver
Propagation Delay
tPHL, tPLH
Interrupt Propagation Delay
VBUS_CHRG Propagation Delay
Dominated by the VBUS rise time
0.2
ns
µs
_______________________________________________________________________________________
5
MAX3301E/MAX3302E
TIMING CHARACTERISTICS
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
I2C-/SMBus™-COMPATIBLE TIMING SPECIFICATIONS
(VCC = +3V to +4.5V, VL = +1.65V to +3.6V, CFLYING = 100nF, CVBUS = 1µF, ESRCVBUS = 0.1Ω (max), TA = TMIN to TMAX, unless
otherwise noted. Typical values are at VCC = +3.7V, VL = +2.5V, TA = +25°C.) (Note 2)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
400
kHz
Serial Clock Frequency
fSCL
Bus-Free Time Between Stop and
Start Conditions
tBUF
1.3
µs
Start-Condition Hold Time
tHD_STA
0.6
µs
Stop-Condition Setup Time
tSU_STO
0.6
µs
tLOW
1.3
µs
Clock Low Period
Clock High Period
tHIGH
0.6
µs
Data Setup Time
tSU_DAT
100
ns
Data Hold Time
tHD_DAT
(Note 4)
Rise Time of SDA and SCL
tR
(Note 5)
Fall Time of SDA and SCL
tF
Measured from 0.3 x VL to 0.7 x VL (Note 5)
Capacitive Load for each Bus
Line
CB
20 +
0.1 x
CB
0.9
µs
300
ns
300
ns
400
pF
0.3 x
VL
V
SDA AND SCL I/O STAGE CHARACTERISTICS
Input-Voltage Low
VIL
Input-Voltage High
VIH
SDA Output-Voltage Low
VOL
ISINK = 3mA
Pulse Width of Suppressed Spike
tSP
(Note 6)
0.7 x
VL
V
0.4
50
V
ns
Note 2: Parameters are 100% production tested at +25°C. Limits over temperature are guaranteed by design.
Note 3: Guaranteed by bench characterization. Limits are not production tested.
Note 4: A master device must provide a hold time of at least 300ns for the SDA signal to bridge the undefined region of SCL’s falling
edge.
Note 5: CB is the total capacitance of one bus line in pF, tested with CB = 400pF.
Note 6: Input filters on SDA, SCL, and ADD suppress noise spikes of less than 50ns.
SMBus™ is a trademark of Intel Corporation.
6
_______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
LINEAR REGULATOR
POWERED BY VCC
30
20
10
VCC = 3.0V
VCC = 4.2V
5.25
5.00
4.75
4.50
LINEAR REGULATOR
POWERED BY VCC
4.00
0
4
8
12
16
20
5.50
5.25
IVBUS = 0
5.00
IVBUS = 8mA
4.75
LINEAR REGULATOR
POWERED BY VCC
4.25
0
5.75
MAX3301E toc03
5.50
VBUS OUTPUT VOLTAGE (V)
40
VBUS OUTPUT VOLTAGE
vs. INPUT VOLTAGE (VCC)
MAX3301E toc02
VCC = 3.3V
VCC = 4.2V
VBUS OUTPUT VOLTAGE (V)
INPUT CURRENT (ICC) (mA)
50
VBUS OUTPUT VOLTAGE
vs. VBUS OUTPUT CURRENT
MAX3301E toc01
INPUT CURRENT (ICC)
vs. VBUS OUTPUT CURRENT
4.50
0
5
10
15
20
25
30
2.5
3.0
3.5
4.0
4.5
5.0
VBUS OUTPUT CURRENT (mA)
VBUS OUTPUT CURRENT (mA)
INPUT VOLTAGE (VCC) (V)
TIME TO ENTER SHUTDOWN
TIME TO EXIT SHUTDOWN
VBUS DURING SRP
MAX3301E toc04
5.5
6.0
MAX3301E/MAX3302E
Typical Operating Characteristics
(Typical operating circuit, VCC = +3.7V, VL = +2.5V, CFLYING = 100nF, TA = +25°C, unless otherwise noted.)
MAX3301E toc06
MAX3301E toc05
D+
1V/div
D1V/div
D1V/div
D+
1V/div
SCL
2V/div
SCL
1V/div
VBUS
1V/div
CVBUS > 13µF
VBUS
1V/div
CVBUS > 96µF
100ns/div
4µs/div
20ns/div
DRIVER PROPAGATION DELAY HIGH-TO-LOW
(LOW-SPEED MODE)
DRIVER PROPAGATION DELAY LOW-TO-HIGH
(LOW-SPEED MODE)
DRIVER PROPAGATION DELAY HIGH-TO-LOW
(FULL-SPEED MODE)
MAX3301E toc07
100ns/div
MAX3301E toc08
MAX3301E toc09
DAT_VP
1V/div
DAT_VP
1V/div
DAT_VP
1V/div
D1V/div
D+
1V/div
D1V/div
D+
1V/div
D1V/div
100ns/div
D+
1V/div
4ns/div
_______________________________________________________________________________________
7
Typical Operating Characteristics (continued)
(Typical operating circuit, VCC = +3.7V, VL = +2.5V, CFLYING = 100nF, TA = +25°C, unless otherwise noted.)
DRIVER PROPAGATION DELAY LOW-TO-HIGH
(FULL-SPEED MODE)
DRIVER ENABLE DELAY
(FULL-SPEED MODE)
MAX3301E toc10
MAX3301E toc11
MAX3301E toc12
OE/INT
1V/div
DAT_VP
1V/div
OE/INT
1V/div
D+
1V/div
D+
1V/div
D1V/div
D1V/div
D+
1V/div
D1V/div
4ns/div
10ns/div
10ns/div
DRIVER DISABLE DELAY
(LOW-SPEED MODE)
MAX3301E toc13
SUPPLY CURRENT
vs. TEMPERATURE
MAX3301E toc14
1.0
OE/INT
1V/div
OE/INT
1V/div
D+
1V/div
D1V/div
D1V/div
D+
1V/div
MAX3301E toc15
DRIVER ENABLE DELAY
(LOW-SPEED MODE)
CD+ = CD- = 400pF
DRIVER DISABLE DELAY
(FULL-SPEED MODE)
0.8
SUPPLY CURRENT (mA)
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
0.6
VCC = 4.2V
VCC = 3.3V
0.4
0.2
VBUS OFF
FULL-SPEED IDLE
0
100ns/div
10ns/div
-40
-15
10
35
TEMPERATURE (°C)
8
_______________________________________________________________________________________
60
85
USB On-the-Go Transceivers and Charge Pumps
PIN
NAME
FUNCTION
MAX3302E
28-PIN TQFN
MAX3301E
32-PIN TQFN
UCSP
1
2
D2
DAT_VP
2, 25
3, 29
D1,
E3
VCC
Input Power Supply. Connect a +3V to +4.5V supply to VCC and bypass to
GND with a 1µF capacitor. The supply range enables direct powering from
one Li+ battery.
3, 9, 23
1, 4, 9, 12, 17,
25, 28
—
N.C.
No Connection. Not internally connected.
4
5
C1
C-
5
6
C2
SE0_VM
6, 18
7, 21
B1,
C5
GND
Ground
7
8
A1
SDA
I2C-Compatible Serial Data Interface. Open-drain data input/output.
8
10
B2
SCL
System-Side Data Input/Output. DAT_VP is an input if OE/INT is logic 0.
DAT_VP is an output if OE/INT is logic 1. Program the function of DAT_VP
with the dat_se0 bit (bit 2 of control register 1, see Table 7).
Charge-Pump Flying-Capacitor Negative Terminal
System-Side Data Input/Output. SE0_VM is an input if OE/INT is logic 0.
SE0_VM is an output if OE/INT is logic 1. Program the function of SE0_VM
with the dat_se0 bit (bit 2 of control register 1, see Table 7).
I2C-Compatible Serial Clock Input
10
11
A2
OE/INT
Output Enable. OE/INT controls the input or output status of DAT_VP/SE0_VM
and D+/D-. When OE/INT is logic 0, the device is in transmit mode. When
OE/INT is logic 1, the device is in receive mode. When in suspend mode,
OE/INT can be programmed to function as an interrupt output that detects the
same interrupts as INT. The oe_int_en bit (bit 5 of control register 1, see Table
7) enables and disables the interrupt circuitry of OE/INT. The irq_mode bit (bit 1
of special-function register 2, see Table 15) programs the output configuration
of INT and OE/INT as open-drain or push-pull.
11
13
A3
RCV
D+ and D- Differential Receiver Output. In receive mode (see Table 4), when
D+ is high and D- is low, RCV is high. In receive mode, when D+ is low and
D- is high, RCV is low. RCV is low in suspend mode.
SPD
Speed-Selector Input. Connect SPD to GND to select the low-speed data rate
(1.5Mbps). Connect SPD to VL to select the full-speed data rate (12Mbps).
Disable the SPD input by writing a 1 to spd_susp_ctl (bit 1 in special-function
register 1, see Table 14). The speed bit (bit 0 of control register 1, see Table
7) determines the maximum data rate of the MAX3301E/MAX3302E when the
SPD input is disabled.
12
13
14
14
15
16
B3
A4
A5
VL
SUS
System-Side Logic-Supply Input. Connect to the system’s logic-level power
supply, +1.65V to +3.6V. This sets the maximum output levels of the logic
outputs and the input thresholds of the logic inputs. Bypass to GND with a
0.1µF capacitor.
Active-High Suspend Input. Drive SUS low for normal USB operation. Drive
SUS high to enable suspend mode. RCV asserts low in suspend mode.
Disable the SUS input by writing a 1 to spd_susp_ctl (bit 1 in special-function
register 1, see Table 14). The suspend bit (bit 1 of control register 1, see
Table 7) determines the operating mode of the MAX3301E/MAX3302E when
the SUS input is disabled.
_______________________________________________________________________________________
9
MAX3301E/MAX3302E
Pin Description
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
Pin Description (continued)
PIN
NAME
FUNCTION
B4
INT
Active-Low Interrupt Source. Program the INT output as push-pull or opendrain with the irq_mode bit (bit 1 of special-function register 2, see Tables 15
and 16).
19
B5
RESET
17
20
C3
ADD
I2C-Interface Address Selection Input. (See Table 5.)
19
22
C4
ID_IN
ID Input. ID_IN is internally pulled up to VCC. The state of ID_IN determines
ID bits 3 and 5 of the interrupt source register (see Table 10).
20
23
D5
D-
USB Differential Data Input/Output. Connect D- to the D- terminal of the USB
connector through a 27.4Ω ±1% series resistor.
21
24
E5
D+
USB Differential Data Input/Output. Connect D+ to the D+ terminal of the USB
connector through a 27.4Ω ±1% series resistor.
22
26
D4
VM
Single-Ended Receiver Output. VM functions as a receiver output in all
operating modes. VM duplicates D-.
MAX3302E
28-PIN TQFN
MAX3301E
32-PIN TQFN
UCSP
15
18
16
Active-Low Reset Input. Drive RESET low to asynchronously reset the
MAX3301E/MAX3302E.
USB Transceiver Regulated Output Voltage. TRM provides a regulated 3.3V
output. Bypass TRM to GND with a 1µF ceramic capacitor installed as close
to the device as possible. TRM normally derives power from VCC. TRM
provides power to internal circuitry and provides the pullup voltage for the
internal USB pullup resistor. Do not use TRM to power external circuitry. The
reg_sel bit (bit 3 of special-function register 2, see Table 15 and Table 16)
controls the TRM power source with software.
24
27
E4
TRM
26
30
D3
VP
27
31
E2
VBUS
28
32
E1
C+
Charge-Pump Flying-Capacitor Positive Terminal
EP
EP
—
EP
Exposed Paddle. Connect to GND or leave floating
Single-Ended Receiver Output. VP functions as a receiver output in all
operating modes. VP duplicates D+.
USB Bus Power. Use VBUS as an output to power the USB bus, or as an input
to power the internal linear regulator. Bits 5 to 7 of control register 2 (see
Table 8) control the charging and discharging functions of VBUS.
Test Circuits and Timing Diagrams
TEST POINT
27.4Ω
220Ω
DUT
D+/DCL
LOAD FOR DISABLE TIME (D+/D-) MEASUREMENT
V = 0 FOR tPHZ.
V = VTRM FOR tPLZ.
CL = 50pF FOR FULL SPEED.
CL = 200pF TO 600pF FOR LOW SPEED.
V
Figure 1. Load for Disable Time Measurement
10
TEST POINT
27.4Ω
DUT
D+/D15kΩ
LOAD FOR
1) ENABLE TIME (D+/D-) MEASUREMENT
2) DAT_VP/SEO_VM TO D+/D- PROPAGATION DELAY
3) D+/D- RISE/FALL TIMES
CL CL = 50pF FOR FULL SPEED.
CL = 200pF TO 600pF FOR LOW SPEED.
Figure 2. Load for Enable Time, Transmitter Propagation Delay,
and Transmitter Rise/Fall Times
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
TEST POINT
DUT
RCV, VP, VM,
DAT_VP,
SEO_VM
VL
LOAD FOR
1) D+/D- TO RCV/VP/VM/DAT_VP/SEO_VM PROPAGATION DELAYS
2) RCV/VP/VM/DAT_VP/SEO_VM RISE/FALL TIMES (CL = 15pF)
VL / 2
OE/INT
0V
CL
VL / 2
tPZD
VOH
tPDZ
VOHD - 0.3V
D+ OR D-
Figure 3. Load for Receiver Propagation Delay and Receiver
Rise/Fall Times
VOLD + 0.3V
VOL
Figure 8. Enable and Disable Timing
TEST POINT
270Ω
DUT
3V
D+
DAT_VP
SEO_VM
V = 2/3 x VL
0V
DtPHL
Figure 4. Load for DAT_VP, SE0_VM Enable/Disable Time
Measurements
tPLH
VL
RCV
VL / 2
0V
tR
tPHL
tF
tPLH
DAT_VP
VOH
VL
90%
VL / 2
0V
10%
VOL
tPLH
tPHL
SE0_VM
VL
VL / 2
Figure 5. Rise and Fall Times
0V
D+/D- RISE/FALL TIMES ≤ 8ns, VL = 1.8V, 2.5V, OR 3.3V
DAT_VP
tPHL
tPLH
Figure 9. D+/D- to RCV, DAT_VP, SE0_VM Propagation Delays
(VP_VM Mode)
SE0_VM
D+ VOHD
VCRS_F, VCRS_L
VCRS_F, VCRS_L
D- VOLD
3V
D+
Figure 6. Timing of DAT_VP, SE0_VM to D+, D- in VP_VM
Mode (dat_se0 = 0)
0V
DtPHL
tPLH
VL
DAT_VP
DAT_VP
tPHL
VL / 2
tPLH
0V
SE0_VM
D+ VOHD
SE0_VM
VCRS_F, VCRS_L
VCRS_F, VCRS_L
D- VOLD
Figure 7. Timing of DAT_VP, SE0_VM to D+/D- in DAT_SE0
Mode (dat_se0 = 1)
D+/D- RISE/FALL TIMES ≤ 8ns, VL = 1.8V, 2.5V, OR 3.3V
Figure 10. D+/D- to DAT_VP, SE0_VM Propagation Delays
(DAT_SE0 Mode)
______________________________________________________________________________________
11
MAX3301E/MAX3302E
Test Circuits and Timing Diagrams (continued)
USB On-the-Go Transceivers and Charge Pumps
MAX3301E/MAX3302E
Block Diagram
ID
DETECTOR
ADD
INT
RESET
ID_IN
C+
C-
VBUS
CHARGE PUMP
SERIAL
CONTROLLER
SCL
VBUS
COMPARATORS
VBUS
LINEAR
REGULATOR
TRM
PULLUP/PULLDOWN
RESISTORS
SDA
CAR KIT INTERRUPT
DETECTOR
DAT_VP
SE0_VM
OE/INT
VP
VM
RCV
POWER
BLOCK
D-
DIFF
RX
LEVEL
TRANSLATOR
VCC
VL
D+
DIFF
TX
SE
D+
GND
SPD
SUS
SE
DMAX3301E
MAX3302E
Figure 11. Block Diagram
12
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
The USB OTG specification defines a dual-role USB
device that acts either as an A device or as a B device.
The A device supplies power on V BUS and initially
serves as the USB host. The B device serves as the initial peripheral and requires circuitry to monitor and pulse
VBUS. These initial roles can be reversed using HNP.
The MAX3301E/MAX3302E combine a low- and fullspeed USB transceiver with additional circuitry required
by a dual-role device. The MAX3301E/MAX3302E
employ flexible switching circuitry to enable the device
to act as a dedicated host or peripheral USB transceiver. For example, the charge pump can be turned off and
the internal regulator can be powered from VBUS for
bus-powered peripheral applications.
The Selector Guide shows the differences between the
MAX3301E and MAX3302E. The MAX3301E powers up
in its lowest power state and must be turned on by setting the sdwn bit to 0. The MAX3302E powers up in the
operational, VP/VM USB mode. This allows a microprocessor (µP) to use the USB port for power-on bootup, without having to access I2C. To put the MAX3302E
into low-power shutdown, set the sdwn bit to 0. In the
MAX3302E, special-function register 2 can be
addressed at I2C register location 10h, 11h (as well as
locations 16h, 17h) to support USB OTG serial-interface
engine (SIE) implementations that are limited to I2C
register addresses between 0h and 15h.
Transceiver
The MAX3301E/MAX3302E transceiver complies with
the USB version 2.0 specification, and operates at fullspeed (12Mbps) and low-speed (1.5Mbps) data rates.
Set the data rate with the SPD input. Set the direction of
data transfer with the OE/INT input. Alternatively, control
transceiver operation with control register 1 (Table 7)
and special-function registers 1 and 2 (see Tables 14,
15, and 16).
Level Shifters
Internal level shifters allow the system-side interface to
run at logic-supply voltages as low as +1.65V. Interface
logic signals are referenced to the voltage applied to
the logic-supply voltage, VL.
Charge Pump
The MAX3301E/MAX3302E’s OTG-compliant charge
pump operates with +3V to +4.5V input supply voltages
(VCC) and supplies a +4.8V to +5.25V OTG-compatible
output on VBUS while sourcing the 8mA or greater output current that an A device is required to supply.
Connect a 0.1µF flying capacitor between C+ and C-.
Bypass VBUS to GND with a 1µF to 6.5µF capacitor, in
accordance with USB OTG specifications. The charge
pump can be turned off to conserve power when not
used. Control of the charge pump is set through the
vbus_drv bit (bit 5) of control register 2 (see Table 8).
Linear Regulator (TRM)
An internal 3.3V linear regulator powers the transceiver
and the internal 1.5kΩ D+/D- pullup resistor. Under the
control of internal register bits, the linear regulator can be
powered from VCC or VBUS. The regulator power-supply
settings are controlled by the reg_sel bit (bit 3) in specialfunction register 2 (Tables 15 and 16). This flexibility
allows the system designer to configure the MAX3301E/
MAX3302E for virtually any USB power situation.
The output of the TRM is not a power supply. Do not use
as a power source for any external circuitry. Connect a
1.0µF (or greater) ceramic or plastic capacitor from TRM
to GND, as close to the device as possible.
VBUS Level-Detection Comparators
Comparators drive interrupt source register bits 0, 1,
and 7 (Table 10) to indicate important USB OTG VBUS
voltage levels:
• VBUS is valid (vbus_vld)
•
USB session is valid (sess_vld)
•
USB session has ended (sess_end)
The vbus_valid comparator sets vbus_vld to 1 if VBUS is
higher than the VBUS valid comparator threshold. The
VBUS valid status bit (vbus_vld) is used by the A device
to determine if the B device is sinking too much current
(i.e., is not supported). The session_valid comparator
sets sess_vld to 1 if VBUS is higher than the session
valid comparator threshold. This status bit indicates that
a data transfer session is valid. The session_end comparator sets sess_end to 1 if VBUS is higher than the
VBUS
VBUS_VLD
VTH-VBUS
SESS_VLD
VTH-SESS_VLD
SESS_END
VTH-SESS_END
Figure 12. Comparator Network Diagram
______________________________________________________________________________________
13
MAX3301E/MAX3302E
Detailed Description
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
session end comparator threshold. Figure 12 shows the
level-detector comparators. The interrupt-enable registers (Tables 12 and 13) determine whether a falling or
rising edge of VBUS asserts these status bits.
ID_IN
The USB OTG specification defines an ID input that
determines which dual-role device is the default host.
An OTG cable connects ID to ground in the connector
of one end and is left unconnected in the other end.
Whichever dual-role device receives the grounded end
becomes the A device. The MAX3301E/MAX3302E provide an internal pullup resistor on ID_IN. Internal comparators detect if ID_IN is grounded or left floating.
Interrupt Logic
When OTG events require action, the MAX3301E/
MAX3302E provide an interrupt output signal on INT.
Alternatively, OE/INT can be configured to act as an
interrupt output while the device operates in USB suspend mode. Program INT and OE/INT as open-drain or
push-pull interrupts with irq_mode (bit 1 of special-function register 2, see Tables 15 and 16).
VBUS Power Control
VBUS is a dual-function port that powers the USB bus
and/or provides a power source for the internal linear regulator. The VBUS power-control block performs the various
switching functions required by an OTG dual-role device.
These actions are programmed by the system logic using
bits 5 to 7 of control register 2 (see Table 8) to:
•
Discharge VBUS through a resistor
•
Provide power-on or receive power from VBUS
•
Charge VBUS through a resistor
The OTG supplement allows an A device to turn VBUS
off when the bus is not being used to conserve power.
The B device can issue a request that a new session be
started using SRP. The B device must discharge VBUS
to a level below the session-end threshold (0.8V) to
ensure that no session is in progress before initiating
SRP. Setting bit 6 of control register 2 to 1, discharges
VBUS to GND through a 5kΩ current-limiting resistor.
When VBUS has discharged, the resistor is removed
from the circuit by resetting bit 6 of control register 2.
An OTG A device is required to supply power on VBUS.
The MAX3301E/MAX3302E provide power to VBUS from
VCC or from the internal charge pump. Set bit 5 in control
register 2 to 1 in both cases. Bit 5 in control register 2
controls a current-limited switch, preventing damage to
the device in the event of a VBUS short circuit.
An OTG B device (peripheral mode) can request a session using SRP. One of the steps in implementing SRP
requires pulsing VBUS high for a controlled time. A 930Ω
resistor limits the current according to the OTG specification. Pulse VBUS through the pullup resistor by asserting bit 7 of control register 2. Prior to pulsing VBUS (bit
7), a B device first connects an internal pulldown resistor to discharge VBUS below the session-end threshold.
The discharge current is limited by the 5kΩ resistor and
set by bit 6 of control register 2. An OTG A device must
Table 1. Functional Blocks Enabled During Specific Operating Modes
MODE
I2C
ID_IN
sess_end
COMP
sess _vld
COMP
vbus_ vld
COMP
cr_int
COMP
dp_hi
COMP
dm_hi
COMP
TRM
TX
DIFF
RX
SE
RX
Shutdown1
✓
X
X
X
X
X
X
X
X
X
X
X
Interrupt
Shutdown2
✓
✓
X
✓
X
X
✓
✓
X
X
X
X
Suspend3
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
X
✓
Normal
Operating
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓
✓ = Enabled.
X = Disabled.
1. For the MAX3301E, enter shutdown mode by writing a 1 to sdwn (bit 0 of special-function register 2). For the MAX3302E, enter
shutdown mode by writing a 0 to sdwn (bit 0 of special-function register 2).
2. Enter interrupt shutdown mode by writing a 1 to int_sdwn (bit 0 of special-function register 1).
3. Enter suspend mode by writing a 1 to spd_susp_ctl (bit 1 of special-function register 1) and suspend (bit 1 of control register 1), or
by writing a 0 to spd_susp_ctl (bit 1 of special-function register 1) and driving SUS high.
14
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
Operating Modes
The MAX3301E/MAX3302E have four operating modes to
optimize power consumption. Only the I2C interface
remains active in shutdown mode, reducing supply current to 1µA. The I2C interface, the ID_IN port, and the
session-valid comparator all remain active in interrupt
shutdown mode. RCV asserts low in suspend mode; however, all other circuitry remains active. Table 1 lists the
active blocks’ power in each of the operating modes.
Applications Information
Data Transfer
Transmitting Data to the USB
The MAX3301E/MAX3302E transceiver features two
modes of transmission: DAT_SE0 or VP_VM (see Table 3).
Set the transmitting mode with dat_se0 (bit 2 in control
register 1, see Table 7). In DAT_SE0 mode with OE/INT
low, DAT_VP specifies data for the differential transceiver, and SE0_VM forces D+/D- to the single-ended zero
(SE0) state. In VP_VM mode with OE/INT low, DAT_VP
drives D+, and SE0_VM drives D-. The differential
receiver determines the state of RCV.
Receiving Data from the USB
The MAX3301E/MAX3302E transceiver features two
modes of receiving data: DAT_SE0 or VP_VM (see
Table 4). Set the receiving mode with dat_se0 (bit 2 in
control register 1, see Table 7). In DAT_SE0 mode with
OE/INT high, DAT_VP is the output of the differential
receiver and SE0_VM indicates that D+ and D- are both
logic-low. In VP_VM mode with OE/INT high, DAT_VP
provides the input logic level of D+ and SE0_VM provides the input logic level of D-. The differential receiver
determines the state of RCV. VP and VM echo D+ and
D-, respectively.
OE/INT
OE/INT controls the direction of communication. OE/INT
can also be programmed to act as an interrupt output
when in suspend mode. The output-enable portion controls the input or output status of DAT_VP/SE0_VM and
D+/D-. When OE/INT is a logic 0, DAT_VP and SE0_VM
function as inputs to the D+ and D- outputs in a method
depending on the status of dat_se0 (bit 2 in control register 1). When OE/INT is a logic 1, DAT_VP and SE0_VM
indicate the activity of D+ and D-.
OE/INT functions as an interrupt output when the
MAX3301E/MAX3302E is in suspend mode and
oe_int_en = 1 (bit 5 in control register 1, see Table 7). In
this mode, OE/INT detects the same interrupts as INT.
Set irq_mode (bit 1 in special-function register 2, see
Tables 15 and 16) to 0 to program OE/INT as an opendrain interrupt output. Set irq_mode to 1 to configure
OE/INT as a push-pull interrupt output.
RCV
RCV monitors D+ and D- when receiving data. RCV is a
logic 1 for D+ high and D- low. RCV is a logic 0 for D+
low and D- high. RCV retains its last valid state when D+
and D- are both low (single-ended zero, or SE0). RCV
asserts low in suspend mode. Table 4 shows the state
of RCV.
SPD
Use hardware or software to control the slew rate of the
D+ and D- terminals. The SPD input sets the slew rate of
the MAX3301E/MAX3302E when spd_susp_ctl (bit 1 in
special-function register 1, see Table 14) is 0. Drive SPD
low to select low-speed mode (1.5Mbps). Drive SPD
high to select full-speed mode (12Mbps). Alternatively,
when spd_susp_ctl (bit 1 of special-function register 1)
is 1, software controls the slew rate. The SPD input is
ignored when using software to control the data rate.
The speed bit (bit 0 of control register 1, see Table 7)
sets the slew rate when spd_susp_ctl = 1.
SUS
Use hardware or software to control the suspend mode
of the MAX3301E/MAX3302E. Set spd_susp_ctl (bit 1 of
special-function register 1, see Table 14) to 0 to allow
the SUS input to enable and disable the suspend mode
of the MAX3301E/MAX3302E. Drive SUS low for normal
operation. Drive SUS high to enable suspend mode.
RCV asserts low in suspend mode while all other circuitry remains active.
Alternatively, when the spd_susp_ctl bit (bit 1 of specialfunction register 1) is set to 1, software controls the suspend mode. Set the suspend bit (bit 1 of control register
1, see Table 7) to 1 to enable suspend mode. Set the
suspend bit to 0 to resume normal operation. The SUS
input is ignored when using software to control suspend
mode. The MAX3301E/MAX3302E must be in full-speed
mode (SPD = high or speed = 1) to issue a remote
wake-up from the device when in suspend mode.
RESET
The active-low RESET input allows the MAX3301E/
MAX3302E to be asynchronously reset without cycling
the power supply. Drive RESET low to reset the internal
registers (see Tables 7–16 for the default power-up
states). Drive RESET high for normal operation.
______________________________________________________________________________________
15
MAX3301E/MAX3302E
supply 5V power and at least 8mA on VBUS. Setting bit
5 of control register 2 turns on the VBUS charge pump.
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
2-Wire I2C-Compatible Serial Interface
A register file controls the various internal switches and
operating modes of the MAX3301E/MAX3302E through
a simple 2-wire interface operating at clock rates up to
400kHz. This interface supports data bursting, where
multiple data phases can follow a single address phase.
Table 2. Setting the Direction of Data
Transfer in General-Purpose Buffer Mode
dplus_dir
dminus_ dir
DIRECTION OF DATA
TRANSFER
UART Mode
0
0
Set uart_en (bit 6 in control register 1) to 1 to place the
MAX3301E/MAX3302E in UART mode. D+ transfers
data to DAT_VP and SE0_VM transfers data to D- in
UART mode.
DAT_VP → D+
SE0_VM → D-
0
1
DAT_VP → D+
SE0_VM ← D-
1
0
DAT_VP ← D+
SE0_VM → D-
1
1
DAT_VP ← D+
SE0_VM ← D-
General-Purpose Buffer Mode
Set gp_en (bit 7 in special-function register 1) and
dat_se0 (bit 2 in control register 1) to 1, set uart_en (bit 6
in control register 1) to 0, and drive OE/INT low to place
the MAX3301E/MAX3302E in general-purpose buffer
mode. Control the direction of data transfer with dminus_dir and dplus_dir (bits 3 and 4 of special-function
register 1, see Tables 2 and 14).
Serial Addressing
The MAX3301E/MAX3302E operate as a slave device
that sends and receives control and status signals
through an I2C-compatible 2-wire interface. The interface uses a serial data line (SDA) and a serial clock line
(SCL) to achieve bidirectional communication between
master(s) and slave(s). A master (typically a microcontroller) initiates all data transfers to and from the
MAX3301E/MAX3302E and generates the SCL clock
that synchronizes the data transfer (Figure 13).
The MAX3301E/MAX3302E SDA line operates as both an
input and as an open-drain output. SDA requires a
pullup resistor, typically 4.7kΩ. The MAX3301E/
MAX3302E SCL line only operates as an input. SCL
requires a pullup resistor if there are multiple masters on
the 2-wire interface, or if the master in a single-master
system has an open-drain SCL output.
Each transmission consists of a start condition (see
Figure 14) sent by a master device, the MAX3301E/
MAX3302E 7-bit slave address (determined by the state
of ADD), plus an R/W bit (see Figure 15), a register
address byte, one or more data bytes, and a stop condition (see Figure 14).
SDA
tBUF
tSU: STA
tSU: DAT
tHD: DAT
tLOW
tHD: STA
tSU: STO
SCL
tHIGH
tHD: STA
tR
tF
START
CONDITION
REPEATED START
CONDITION
STOP
START
CONDITION CONDITION
Figure 13. 2-Wire Serial-Interface Timing Details
16
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
CONTROL PIN/BIT
MODE
INPUT
OUTPUT
DESCRIPTION
DAT_SE0
DAT_VP
SE0_VM
D+
D-
0
OE/INT
0
1
0
0
0
1
0
0
1
1
0
1
0
0
0
0
1
0
1
0
0
0
0
0
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
0
0
0
0
0
0
1
0
1
0
0
0
0
1
1
1
1
1
0
0
1
0
0
0
1
1
0
0
1
1
0
1
0
1
0
0
1
0
1
0
0
1
0
0
1
1
1
0
0
1
0
0
0
0
0
0
0
1
0
0
0
1
0
1
0
1
0
0
0
0
1
0
1
1
0
0
0
1
1
1
1
1
0
1
X
X
X
Driver is
Hi-Z
Driver is
Hi-Z
Receiving
0
0
1
X
X
X
Driver is
Hi-Z
Driver is
See Table 4
Hi-Z
Generalpurpose
buffer
X
1
0
1
Functional
DAT_SE0
Functional
VP_VM
Suspend
SUS
GP_EN
0
0
USB functional mode
transceiver and I2C interface
are fully functional
USB suspend mode
General-purpose buffer
mode
See Table 2
SDA
S
P
START
CONDITION
STOP
CONDITION
SCL
Figure 14. Start and Stop Conditions
1
SDA
START
MSB
0
0
1
0
0
A0
R/W
ACK
LSB
SCL
Figure 15. Slave Address
______________________________________________________________________________________
17
MAX3301E/MAX3302E
Table 3. Transmit Mode
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
Table 4. Receive Mode
CONTROL PIN/BIT
MODE
Functional
DAT_SE0
Functional
VP_VM
INPUTS
SUS
(NOTE 7)
GP_EN
OE/INT
DAT_SE0
0
0
1
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
1
1
0
1
OUTPUTS
D-
DAT_VP
SE0_VM
RCV
0
0
Last value
of DAT_VP
1
Last value
of RCV
1
1
0
1
0
1
1
0
1
0
0
0
1
1
1
1
Undefined
0
Undefined
1
1
0
0
0
1
0
1
1
1
0
1
0
0
BI_DI D+
1
0
1
1
1
0
1
0
0
0
1
0
1
1
1
1
1
1
0
0
0
0
1
0
1
0
0
0
0
Last value
of RCV
0
0
1
0
1
1
0
1
0
1
0
0
1
0
1
0
1
0
1
0
0
0
1
0
1
1
1
1
1
Undefined
1
0
1
0
1
0
0
0
0
0
1
0
1
0
1
1
0
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
1
1
1
0
Generalpurpose buffer
X
1
X
X
X
See Table 2
0
Transmitting
(see Table 3)
X
X
0
X
X
—
0
Unidirectional
(transmitter
only)
X
X
X
X
0
—
0
VP
VM
Echo
D+
Echo
D-
Note 7: Enter suspend mode by driving SUS high or by writing a 1 to suspend (bit 1 in control register 1), depending on the status of
spd_susp_ctl in special-function register 1.
X = Don’t care.
18
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
Bit Transfer
One data bit is transferred during each clock pulse. The
data on SDA must remain stable while SCL is high (see
Figure 16).
Acknowledge
The acknowledge bit (ACK) is the 9th bit attached to
any 8-bit data word. ACK is always generated by the
receiving device. The MAX3301E/MAX3302E generate
SDA
SCL
DATA LINE STABLE, CHANGE OF DATA
DATA VALID
ALLOWED
an ACK when receiving an address or data by pulling
SDA low during the ninth clock period. When transmitting data, the MAX3301E/MAX3302E wait for the receiving device to generate an ACK. Monitoring ACK allows
for detection of unsuccessful data transfers. An unsuccessful data transfer occurs if a receiving device is busy
or if a system fault has occurred. In the event of an
unsuccessful data transfer, the bus master should reattempt communication at a later time.
Slave Address
A bus master initiates communication with a slave
device by issuing a START condition followed by the 7bit slave address (see Figure 15). When idle, the
MAX3301E/MAX3302E wait for a START condition followed by its slave address. The LSB of the address
word is the read/write (R/W) bit. R/W indicates whether
the master is writing to or reading from the
MAX3301E/MAX3302E (R/W = 0 selects the write condition, R/W = 1 selects the read condition). After
receiving the proper address, the MAX3301E/
MAX3302E issue an ACK.
The MAX3301E/MAX3302E have two possible addresses
(see Table 5). Address bits A6 through A1 are preset,
while a reset condition or an I2C general call address
loads the value of A0 from ADD. Connect ADD to GND to
set A0 to 0. Connect ADD to VL to set A0 to 1. This allows
up to two MAX3301E’s or two MAX3302E’s to share the
same bus.
Write Byte Format
Figure 16. Bit Transfer
START
CONDITION
CLOCK PULSE FOR ACKNOWLEDGEMENT
1
SCL
2
8
9
SDA BY
TRANSMITTER
Read Byte Format
Reading data from the MAX3301E/MAX3302E requires
the transmission of at least 3 bytes. The first byte consists of the MAX3301E/MAX3302E’s slave address, followed by a 0 (R/W bit). The second byte selects the
register from which data is read. The third byte consists
S
SDA BY
RECEIVER
Figure 17. Acknowledge
SLAVE ADDRESS
(7 BITS)
S
A6
Writing data to the MAX3301E/MAX3302E requires the
transmission of at least 3 bytes. The first byte consists of
the MAX3301E/MAX3302E’s 7-bit slave address, followed by a 0 (R/W bit). The second byte determines
which register is to be written to. The third byte is the
new data for the selected register. Subsequent bytes
are data for sequential registers. Figure 18 shows the
typical write byte format.
A5
A4
A3
A2
R/W
A1
A0
0
REGISTER ADDRESS
(8 BITS)
A
MSB
DATA
(8 BITS)
A
LSB
MSB
A
P
LSB
Figure 18. Write Byte Format
______________________________________________________________________________________
19
MAX3301E/MAX3302E
Start and Stop Conditions
Both SCL and SDA assert high when the interface is not
busy. A master device signals the beginning of a transmission with a start (S) condition by transitioning SDA
from high to low while SCL is high. The master issues a
stop (P) condition by transitioning SDA from low to high
while SCL is high. The bus is then free for another transmission (see Figure 14).
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
SLAVE ADDRESS
(7 BITS)
S
A6
A5
A4
A3
A2
A1
SLAVE ADDRESS
(7 BITS)
RS
A6
A5
A4
A3
A2
A1
A0
R/W
A
0
0
A0
R/W
A
1
0
REGISTER ADDRESS
(8 BITS)
A
MSB
LSB
DATA
(8 BITS)
MSB
LSB
0
NA
P
1
0
Figure 19. Read Byte Format
R/W: Read/write (R/W = 1: read; R/W = 0: write)
A: Acknowledge bit from the slave
S: Start condition
NA: Not-acknowledged bit from the master
RS: Repeated start condition
Blank: Master transmission
P: Stop condition
SLAVE ADDRESS
(7 BITS)
S
A6
A5
A4
A3
A2
R/W
A1
A0
DATA (K+1)
(8 BITS)
REGISTER ADDRESS (K)
(8 BITS)
A
0
MSB
LSB
DATA (K+2)
(8 BITS)
A
MSB
MSB
LSB
SLAVE ADDRESS
(7 BITS)
S
A6
A5
A4
A3
A2
R/W
A1
A0
0
MSB
LSB
DATA (K+N)
(8 BITS)
MSB
A
P
LSB
MAX3301E/MAX3302E SENDS
AN ACK
UNSUPPORTED REGISTER ADDRESS (K)
(8 BITS)
A
A
MSB
A
LSB
MAX3301E/MAX3302E RECOGNIZES
ITS ADDRESS
DATA (K)
(8 BITS)
A
DATA (K)
(8 BITS)
A
LSB
MSB
NA
LSB
MAX3301E/MAX3302E RECOGNIZES A WRITE TO AN
UNSUPPORTED LOCATION, THEN SENDS A NACK
Figure 20. Burst-Mode Write Byte Format
of the MAX3301E/MAX3302E’s slave address, followed
by a 1 (R/W bit). The master then reads one or more
bytes of data. Figure 19 shows the typical read byte
format.
Burst-Mode Write Byte Format
The MAX3301E/MAX3302E allow a master device to
write to sequential registers without repeatedly sending
the slave address and register address each time. The
master first sends the slave address, followed by a 0 to
write data to the MAX3301E/MAX3302E. The
MAX3301E/MAX3302E send an acknowledge bit back
to the master. The master sends the 8-bit register
20
address and the MAX3301E/MAX3302E return an
acknowledge bit. The master writes a data byte to the
selected register and receives an acknowledge bit if a
supported register address has been chosen. The register address increments and is ready for the master to
send the next data byte. The MAX3301E/MAX3302E
send an acknowledge bit after each data byte. If an
unsupported register is selected, the MAX3301E/
MAX3302E send a NACK to the master and the register
index does not increment (see Figure 20).
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
A6
A5
A4
A3
A2
R/W
A1
A0
SLAVE ADDRESS
(7 BITS)
S
A6
A5
A4
A3
A2
0
A0
DATA (K+2)
(8 BITS)
DATA (K)
(8 BITS)
A
LSB
DATA (K+3)
(8 BITS)
LSB
MSB
LSB
SLAVE ADDRESS
(7 BITS)
A6
A5
A4
A3
A2
R/W
A1
A0
SLAVE ADDRESS
(7 BITS)
S
A6
A5
A4
A3
A2
0
A1
A0
1
A
NA
P
LSB
P
LSB
UNSUPPORTED REGISTER ADDRESS (K)
(8 BITS) — ALL 0's RETURNED
A
DATA (K+N)
(8 BITS)
MAX3301E/MAX3302E SENDS
AN ACK
MSB
R/W
LSB
MSB
UNSUPPORTED REGISTER ADDRESS (K)
(8 BITS)
A
A
MSB
A
MAX3301E/MAX3302E RECOGNIZE
THEIR ADDRESS
S
DATA (K+1)
(8 BITS)
A
MSB
1
P
LSB
A
MSB
A
MSB
R/W
A1
REGISTER ADDRESS (K)
(8 BITS)
A
MAX3301E/MAX3302E
SLAVE ADDRESS
(7 BITS)
S
MSB
A
LSB
ACK FROM MASTER
Figure 21. Burst-Mode Read Byte Format
Table 5. I2C Slave Address Map
ADD INPUT
ADDRESS BITS
A6
A5
A4
A3
A2
A1
A0
GND (0)
0
1
0
1
1
0
0
VL (1)
0
1
0
1
1
0
1
______________________________________________________________________________________
21
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
Table 6. Register Map
REGISTER
MEMORY ADDRESS
Vendor ID
00h, 01h
Read only. The contents of registers 00h and 01h are 6Ah and 0Bh, respectively.
DESCRIPTION
Product ID
02h, 03h
Read only. The contents of registers 02h and 03h are 01h and 33h, respectively.
Control 1
04h (set)
05h (clear)
Sets operating modes, maximum data rate, and direction of data transfer.
Control 2
06h (set)
07h (clear)
Controls D+/D- pullup/pulldown resistor connections, ID_IN state, and VBUS
behavior.
Interrupt source
08h (read)
Read only.
Unused*
09h
Not used.
Interrupt latch
0Ah (set)
0Bh (clear)
Indicates which interrupts have occurred.
Interrupt-enable
Falling edge
0Ch (set)
0Dh (clear)
Enables interrupts for high-to-low transitions.
Interrupt-enable
Rising edge
0Eh (set)
0Fh (clear)
Enables interrupts for low-to-high transitions.
Unused*/Special
Function 2
10h (set)
11h (clear)
MAX3301E: Not used.
MAX3302E: Alternate register addresses for special-function register 2. This
register is also accessible from 16h and 17h.
Special function 1
12h (set)
13h (clear)
Enables hardware/software control of the MAX3301E's behavior, interrupt activity,
and operating modes.
Revision ID
14h, 15h
Read only. The contents of registers 14h and 15h are 77h and 41h, respectively.
Special function 2
16h (set)
17h (clear)
Sets operating modes, INT output configuration, D+/D- behavior in audio mode,
and TRM source.
Unused*
18h–Fh
Not used.
*When writing to an unused register, the device generates a NACK and the register index does not increment.
Burst-Mode Read Byte Format
The MAX3301E/MAX3302E allow a master device to read
data from sequential registers with the burst-mode read
byte protocol (see Figure 21). The master device first
sends the slave address, followed by a 0. The
MAX3301E/MAX3302E then sends an acknowledge bit.
Next, the master sends the register address to the
MAX3301E/MAX3302E, which then generates another
acknowledge bit. The master then sends a stop (P) condition to the MAX3301E/MAX3302E. Next, the master
sends a start condition, followed by the MAX3301E/
MAX3302E’s slave address, and then a 1 to indicate a
read command. The MAX3301E/MAX3302E then sends
data to the master device, one byte at a time. The master
sends an acknowledge bit to the MAX3301E/ MAX3302E
after each data byte, and the register address of the
MAX3301E/MAX3302E increments after each byte. This
continues until the master sends a stop (P) condition. If
22
an unsupported register address is encountered, the
MAX3301E/MAX3302E send a byte of zeros.
Registers
Control Registers
There are two read/write control registers. Control register 1 (Table 7) sets operating modes, sets the data rate,
and controls the direction of data transfer. Control register 2 (Table 8) connects the D+/D- pullup or pulldown
resistors, sets the VBUS charge/discharge conditions,
and grounds ID_IN. The control registers have two
addresses that implement write-one-set and write-oneclear features for each of these registers. Writing a 1 to
the set address sets that bit to 1. Writing a 1 to the clear
address resets that bit to 0. Writing a 0 to either address
has no effect on the bits.
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
SYMBOL
0
speed
Set to 0 for low-speed (1.5Mbps) mode. Set to 1 for full-speed (12Mbps) mode. This
bit changes the data rate only if spd_susp_ctl = 1 in special-function register 1.
0
1
suspend
Set to 0 for normal operating mode. Set to 1 for suspend mode. This bit changes
the operating mode only if spd_susp_ctl = 1 in special-function register 1.
0
2
dat_se0
Set to 0 for VP_VM USB mode. Set to 1 for DAT_SE0 USB mode.
0
3
—
Not used.
0
4
OPERATION
VALUE AT
POWER-UP
BIT NUMBER
Enables the transceiver (when configured as an A device) to connect its pullup
bdis_acon_en resistor if the B device disconnect is detected during HNP. Set to 0 to disable this
feature. Set to 1 to enable this feature.
5
oe_int_en
6
uart_en
7
—
0
Set to 0 to disable the interrupt output circuitry of OE/INT. Set to 1 to enable the
interrupt output circuitry of OE/INT.
0
Set to 0 to disable UART mode. Set to 1 to enable UART mode. This bit overrides
the settings of dminus_dir, dplus_dir, and gp_en bits.
0
Not used.
0
Table 8. Control Register 2 Description (Write to Address 06h to Set, Write to Address
07h to Clear)
SYMBOL
0
dp_pullup
Set to 0 to disconnect the pullup resistor to D+. Set to 1 to connect the pullup resistor to D+.
0
1
dm_pullup
Set to 0 to disconnect the pullup resistor to D-. Set to 1 to connect the pullup resistor to D-.
0
2
dp_pulldown
Set to 0 to disconnect the pulldown resistor to D+. Set to 1 to connect the pulldown
resistor to D+.
1
3
dm_pulldown
Set to 0 to disconnect the pulldown resistor to D-. Set to 1 to connect the pulldown
resistor to D-.
1
4
id_pulldown
Set to 0 to allow ID_IN to float. Set to 1 to connect ID_IN to GND.
0
5
vbus_drv
Set to 0 to turn VBUS off. Set to 1 to drive VBUS through a low impedance (see Note 8).
0
Set to 0 to disconnect the VBUS discharge resistor. Set to 1 to connect the VBUS
discharge resistor (see Note 8).
0
Set to 0 to disconnect the VBUS charge resistor. Set to 1 to connect the VBUS
charge resistor (see Note 8).
0
6
vbus_dischrg
7
vbus_chrg
OPERATION
VALUE AT
POWER-UP
BIT NUMBER
Note 8: To prevent a high-current state where the transceiver is both sourcing current to VBUS and sinking current from VBUS, the following logic is used to set bits 5, 6, and 7 of control register 2:
•
Setting vbus_drv clears vbus_dischrg and vbus_chrg
•
Setting vbus_dischrg clears vbus_drv and vbus_chrg, unless vbus_drv is set with the same command, in which case vbus_drv
clears the other bits
•
Setting vbus_chrg clears vbus_drv and vbus_dischrg, unless either of these bits are set with the same command, as shown in Table 9
______________________________________________________________________________________
23
MAX3301E/MAX3302E
Table 7. Control Register 1 Description (Write to Address 04h to Set, Write to Address
05h to Clear)
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
Table 9. VBUS Control Logic
SET COMMAND (ADDRESS 06h)
BEHAVIOR OF MAX3301E/MAX3302E
vbus_drv
vbus_dischrg
vbus_chrg
vbus_drv
vbus_dischrg
vbus_chrg
1
X
X
1
0
0
0
1
X
0
1
0
0
0
1
0
0
1
0
0
0
Not affected
Not affected
Not affected
X = Don’t care.
Table 10. Interrupt Source Register (Address 08h is Read Only)
BIT NUMBER
SYMBOL
0
vbus_vld
1
sess_vld
CONTENTS
Logic 1 if VBUS > VBUS valid comparator threshold.
Logic 1 if VBUS > session valid comparator threshold.
Logic 1 if VD+ > dp_hi comparator threshold (D+ assertion during data line pulsing through
SRP method).
2
dp_hi
3
id_gnd
Logic 1 if VID_IN < 0.1 x VCC.
4
dm_hi
Logic 1 if VD- > dm_hi comparator threshold (D- assertion during data line pulsing through SRP
method).
5
id_float
6
bdis_acon
7
cr_int_sess_end
Logic 1 if VID_IN > 0.9 x VCC.
Logic 1 if bdis_acon_en = 1 and the MAX3301E/MAX3302E assert dp_pullup after detecting a
B device disconnect during HNP.
Logic 1 if VBUS < sess_end comparator threshold, or if VD+ > cr_int comparator threshold (0.4V to
0.6V), depending on the value of int_source (bit 5 of special-function register 1, see Table 14).
Interrupt Registers
Four registers control all interrupt behavior of the
MAX3301E/MAX3302E. A source register (Table 10)
indicates the current status of the various interrupt
sources. An interrupt latch register (Table 11) indicates
which interrupts have occurred. An interrupt-enable low
and interrupt-enable high register enable interrupts on
rising or falling (or both) transitions. Tables 10–13 provide the bit configurations for the various interrupt registers. The interrupt latch, interrupt-enable low, and
interrupt-enable high registers have two addresses that
implement write- one-set and write-one-clear features for
each of these registers. Writing a 1 to the set address
sets that bit to 1. Writing a 1 to the clear address resets
that bit to 0. Writing a 0 to either address has no effect
on the bits.
Special-Function Registers
Tables 14, 15, and 16 describe the special-function
registers. The special-function registers have two
addresses that implement write-one-set and write-oneclear features for each of these registers. Writing a 1 to
24
the set address sets that bit to 1. Writing a 1 to the clear
address resets that bit to 0. Writing a 0 to either
address has no effect on the bits. Special-function register 1 determines whether hardware or software controls the maximum data rate and suspend behavior,
sets the direction of data transfer, and toggles generalpurpose buffer mode. Special-function register 2
enables shutdown mode, configures the interrupt output as open-drain or push-pull, sets the TRM power
source, and controls the D+/D- connections for audio
mode. Table 15 depicts the special-function register 2
for the MAX3301E and Table 16 depicts the specialfunction register 2 for the MAX3302E.
The MAX3301E powers up in its lowest power state and
must be turned on by setting the sdwn bit to 0. The
MAX3302E powers up in the operational, VP/VM USB
mode. This allows a µP to use the USB port for poweron boot-up, without having to access I2C. To put the
MAX3302E into low-power shutdown, set the sdwn bit
to 0. The MAX3302E also has special-function register
2 mapped to two I 2 C register addresses. In the
MAX3302E, special-function register 2 can be
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
CONTENTS
VALUE AT
POWER-UP
BIT NUMBER
SYMBOL
0
vbus_vld
vbus_vld asserts if a transition occurs on this condition and the appropriate
interrupt-high or interrupt-low enable bit is set. See Tables 10, 12, and 13.
0
1
sess_vld
sess_vld asserts if a transition occurs on this condition and the appropriate
interrupt-high or interrupt-low enable bit is set. See Tables 10, 12, and 13.
0
2
dp_hi
dp_hi asserts if a transition occurs on this condition and the appropriate interrupthigh or interrupt-low enable bit is set. See Tables 10, 12, and 13.
0
3
id_gnd
id_gnd asserts if a transition occurs on this condition and the appropriate interrupthigh or interrupt-low enable bit is set. See Tables 10, 12, and 13.
0
4
dm_hi
dm_hi asserts if a transition occurs on this condition and the appropriate interrupthigh or interrupt-low enable bit is set. See Tables 10, 12, and 13.
0
5
id_float
id_float asserts if a transition occurs on this condition and the appropriate interrupthigh or interrupt-low enable bit is set. See Tables 10, 12, and 13.
0
6
bdis_acon
bdis_acon asserts if a transition occurs on this condition and the appropriate
interrupt-high or interrupt-low enable bit is set. See Tables 10, 12, and 13.
0
7
cr_int_sess_end
cr_int_sess_end asserts if a transition occurs on this condition and the appropriate
interrupt-high or interrupt-low enable bit is set. See Tables 10, 12, and 13.
0
Table 12. Interrupt-Enable Low Register (Write to Address 0Ch to Set, Write to Address
0Dh to Clear)
CONTENTS
VALUE AT
POWER-UP
BIT NUMBER
SYMBOL
0
vbus_vld
Set to 0 to disable the vbus_vld interrupt for a high-to-low transition. Set to 1 to
enable the vbus_vld interrupt for a high-to-low transition. See Tables 10 and 11.
0
1
sess_vld
Set to 0 to disable the sess_vld interrupt for a high-to-low transition. Set to 1 to
enable the sess_vld interrupt for a high-to-low transition. See Tables 10 and 11.
0
2
dp_hi
Set to 0 to disable the dp_hi interrupt for a high-to-low transition. Set to 1 to
enable the dp_hi interrupt for a high-to-low transition. See Tables 10 and 11.
0
3
id_gnd
Set to 0 to disable the id_gnd interrupt for a high-to-low transition. Set to 1 to
enable the id_gnd interrupt for a high-to-low transition. See Tables 10 and 11.
0
4
dm_hi
Set to 0 to disable the dm_hi interrupt for a high-to-low transition. Set to 1 to
enable the dm_hi interrupt for a high-to-low transition. See Tables 10 and 11.
0
5
id_float
Set to 0 to disable the id_float interrupt for a high-to-low transition. Set to 1 to
enable the id_float interrupt for a high-to-low transition. See Tables 10 and 11.
0
6
bdis_acon
Set to 0 to disable the bdis_acon interrupt for a high-to-low transition. Set to 1 to
enable the bdis_acon interrupt for a high-to-low transition. See Tables 10 and 11.
0
7
cr_int_sess_end
Set to 0 to disable the cr_int_sess_end interrupt for a high-to-low transition.
Set to 1 to enable the cr_int_sess_end interrupt for a high-to-low transition.
See Tables 10 and 11.
0
______________________________________________________________________________________
25
MAX3301E/MAX3302E
Table 11. Interrupt Latch Register Description (Write to Address 0Ah to Set, Write to
Address 0Bh to Clear)
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
Table 13. Interrupt-Enable High Register (Write to Address 0Eh to Set, Write to Address
0Fh to Clear)
VALUE AT
POWER-UP
BIT NUMBER
SYMBOL
CONTENTS
0
vbus_vld
Set to 0 to disable the vbus_vld interrupt for a low-to-high transition. Set to 1 to
enable the vbus_vld interrupt for a low-to-high transition. See Tables 10 and 11.
0
1
sess_vld
Set to 0 to disable the sess_vld interrupt for a low-to-high transition. Set to 1 to
enable the sess_vld interrupt for a low-to-high transition. See Tables 10 and 11.
0
2
dp_hi
Set to 0 to disable the dp_hi interrupt for a low-to-high transition. Set to 1 to
enable the dp_hi interrupt for a low-to-high transition. See Tables 10 and 11.
0
3
id_gnd
Set to 0 to disable the id_gnd interrupt for a low-to-high transition. Set to 1 to
enable the id_gnd interrupt for a low-to-high transition. See Tables 10 and 11.
0
4
dm_hi
Set to 0 to disable the dm_hi interrupt for a low-to-high transition. Set to 1 to
enable the dm_hi interrupt for a low-to-high transition. See Tables 10 and 11.
0
5
id_float
Set to 0 to disable the id_float interrupt for a low-to-high transition. Set to 1 to
enable the id_float interrupt for a low-to-high transition. See Tables 10 and 11.
0
6
bdis_acon
Set to 0 to disable the bdis_acon interrupt for a low-to-high transition. Set to 1 to
enable the bdis_acon interrupt for a low-to-high transition. See Tables 10 and 11.
0
7
cr_int_sess_end
Set to 0 to disable the cr_int_sess_end interrupt for a low-to-high transition.
Set to 1 to enable the cr_int_sess_end interrupt for a low-to-high transition.
See Tables 10 and 11.
0
addressed at I2C register location 10h, 11h (as well as
locations 16h, 17h) to support USB OTG SIE implementations that are limited to I 2 C register addresses
between 0h and 15h.
ID and Manufacturer Register Address Map
Table 17 provides the contents of the ID registers of the
MAX3301E/MAX3302E. Addresses 00h and 01h comprise the vendor ID registers. Addresses 02h and 03h
comprise the product ID registers. Addresses 14h and
15h comprise the revision ID registers.
Audio Car Kit
Many cell phones are required to interface to car kits.
Depending upon the car kit, the interface to the phone
may be required to support any or all of the following
functions:
• Audio input
•
Audio output
•
Charging
•
Control and status
D+ and D- of the MAX3301E/MAX3302E go to a highimpedance state when in shutdown mode, allowing
external signals (including audio) to be multiplexed onto
these lines.
26
External Components
External Resistors
Two external resistors (27.4Ω ±1%) are required for
USB connection. Install one resistor in series between
D+ of the MAX3301E/MAX3302E and D+ of the USB
connector. Install the other resistor in series between Dof the MAX3301E/MAX3302E and D- of the USB connector (see the Typical Operating Circuit).
External Capacitors
Five external capacitors are recommended for proper
operation. Install all capacitors as close to the device as
possible. Decouple VL to GND with a 0.1µF ceramic
capacitor. Bypass V CC to GND with a 1µF ceramic
capacitor. Bypass TRM to GND with a 1µF (or greater)
ceramic or plastic capacitor. Connect a 100nF flying
capacitor between C+ and C- for the charge pump (see
the Typical Operating Circuit). Bypass VBUS to GND
with a 1µF to 6.5µF ceramic capacitor in accordance
with USB OTG specifications.
ESD Protection
To protect the MAX3301E/MAX3302E against ESD, D+,
D-, ID_IN, and VBUS, have extra protection against static electricity to protect the device up to ±15kV. The ESD
structures withstand high ESD in all states; normal oper-
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
BIT NUMBER
SYMBOL
0
int_sdwn
1
CONTENTS
VALUE AT
POWER-UP
Set to 0 for normal operation. Set to 1 to enter interrupt shutdown mode. The I2C
interface and interrupt sources remain active, while all other circuitry is off.
0
spd_susp_ctl
Set to 0 to control the MAX3301E/MAX3302E behavior with SPD and SUS. Set to 1 to
control the MAX3301E/MAX3302E behavior with the speed and suspend bits in control
register 1 (see Table 7).
0
2
bi_di
Set to 0 to transfer data from DAT_VP and SE0_VM to D+ and D-, respectively.
DAT_VP and SE0_VM are always inputs when this bit is 0. Set to 1 to control the
direction of data transfer with OE/INT.
1
3
dminus_dir
Set to 0 to transfer data from SE0_VM to D-. Set to 1 to transfer data from D- to
SE0_VM. Ensure that gp_en = 1, dat_se0 = 1, uart_en = 0, and OE/INT = low to
activate this function.
0
4
dplus_dir
Set to 0 to transfer data from DAT_VP to D+. Set to 1 to transfer data from D+ to
DAT_VP. Ensure that gp_en = 1, dat_se0 = 1, uart_en = 0, and OE/INT = low to
activate this function.
0
5
int_source
Set to 0 to use cr_int as the interrupt source for bit 7 of the interrupt source
register. Set to 1 to use sess_end as the interrupt source for bit 7 of the interrupt
source register (see Table 10).
0
6
sess_end
Session end comparator status (read only). Sess_end = 0 when VBUS >
sess_end threshold. Sess_end = 1 when VBUS < sess_end threshold.
—
7
gp_en
Set to 0 to disable general-purpose buffer mode. Set to 1 to enable generalpurpose buffer mode.
0
Note: sess_end value at power-up is dependent on the voltage at VBUS.
Table 15. MAX3301E Special-Function Register 2 (Write to Address 16h to Set, Write to
Address 17h to Clear)
CONTENTS
VALUE AT
POWER-UP
BIT NUMBER
SYMBOL
0
sdwn
Set to 0 for normal operation. Set to 1 to enable shutdown mode. Only the I2C
interface remains active in shutdown.
1
1
irq_mode
Set to 0 to set INT and OE/INT as open-drain outputs. Set to 1 to set INT and
OE/INT as push-pull outputs.
0
2
xcvr_input_disc
Set to 0 to leave the D+/D- single-ended receiver inputs connected. Set to 1 to
disconnect the D+/D- receiver inputs to reduce power consumption in audio mode.
0
3
reg_sel
4–7
—
Set to 0 to power TRM from VCC. Set to 1 to power TRM from VBUS.
Reserved. Set to 0 for normal operation.
ation, suspend mode, interrupt shutdown, and shutdown. For the ESD structures to work correctly, connect
a 1µF or greater capacitor from TRM to GND and from
VBUS to GND. ESD protection can be tested in various
ways; the D+, D-, ID_IN, and VBUS inputs/outputs are
characterized for protection to the following limits:
0
0000
•
±15kV using the Human Body Model
•
±6kV using the IEC 61000-4-2 Contact Discharge
Method
•
±10kV using the IEC 61000-4-2 Air-Gap Discharge
Method
______________________________________________________________________________________
27
MAX3301E/MAX3302E
Table 14. Special-Function Register 1 (Write to Address 12h to Set, Write to Address 13h
to Clear)
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
Table 16. MAX3302E Special-Function Register 2 (Write to Address 10h or 16h to Set,
Write to Address 11h or 17h to Clear)
CONTENTS
VALUE AT
POWER-UP
BIT NUMBER
SYMBOL
0
sdwn
Set to 0 to enable shutdown mode. Set to 1 for normal operation. Only the I2C
interface remains active in shutdown.
1
1
irq_mode
Set to 0 to set INT and OE/INT as open-drain outputs. Set to 1 to set INT and
OE/INT as push-pull outputs.
0
2
xcvr_input_disc
Set to 0 to leave the D+/D- single-ended receiver inputs connected. Set to 1 to
disconnect the D+/D- receiver inputs to reduce power consumption in audio mode.
0
3
reg_sel
4–7
—
Set to 0 to power TRM from VCC. Set to 1 to power TRM from VBUS.
Reserved. Set to 0 for normal operation.
Table 17. ID Registers
REGISTER
Vendor ID
Product ID
Revision ID
ADDRESS
CONTENTS
00h
6Ah
01h
0Bh
02h
01h
03h
33h
14h
77h
15h
41h
ESD performance depends on a variety of conditions.
Contact Maxim for a reliability report that documents
test setup, methodology, and results.
Human Body Model
Figure 22 shows the Human Body Model and Figure 23
shows the current waveform it generates when discharged into a low impedance. This model consists of a
100pF capacitor charged to the ESD voltage of interest,
which is then discharged into the test device through a
1.5kΩ resistor.
test involves approaching the device with a charged
probe. The contact discharge method connects the
probe to the device before the probe is energized.
Figure 25 shows the IEC 61000-4-2 current waveform.
Layout Considerations
The MAX3301E/MAX3302E high operating frequency
makes proper layout important to ensure stability and
maintain the output voltage under all loads. For best
performance, minimize the distance between the
bypass capacitors and the MAX3301E/MAX3302E. Use
symmetric trace geometry from D+ and D- to the USB
connector.
UCSP Applications Information
For the latest application details on UCSP construction,
dimensions, tape carrier information, PC board techniques, bump-pad layout, and the recommended reflow
temperature profile, as well as the latest information on
reliability testing results, refer to the Application Note:
UCSP—A Wafer-Level Chip-Scale Package available on
Maxim’s website at www.maxim-ic.com/ucsp.
IEC 61000-4-2
The IEC 61000-4-2 standard covers ESD testing and
performance of finished equipment; it does not specifically refer to integrated circuits. The MAX3301E/
MAX3302E helps the user design equipment that meets
level 3 of IEC 61000-4-2, without the need for additional
ESD-protection components. The major difference
between tests done using the Human Body Model and
IEC 61000-4-2 is a higher peak current in IEC 61000-4-2,
due to the fact that series resistance is lower in the IEC
61000-4-2 model. Hence, the ESD-withstand voltage
measured to IEC 61000-4-2 is generally lower than that
measured using the Human Body Model. Figure 24
shows the IEC 61000-4-2 model. The Air-Gap Discharge
28
0
0000
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
MAX3301E/MAX3302E
RD
1.5kΩ
RC
1MΩ
I
100%
HIGHVOLTAGE
DC
SOURCE
Cs
100pF
DISCHARGE
RESISTANCE
90%
DEVICE
UNDER
TEST
STORAGE
CAPACITOR
IPEAK
CHARGE-CURRENTLIMIT RESISTOR
Figure 22. Human Body ESD Test Modes
10%
IP 100%
90%
Ir
PEAK-TO-PEAK RINGING
(NOT DRAWN TO SCALE)
t
tR = 0.7ns TO 1ns
30ns
60ns
AMPERES
Figure 25. IEC 61000-4-2 Current Waveform
36.8%
10%
0
0
Chip Information
TIME
tRL
PROCESS: BiCMOS
tDL
CURRENT WAVEFORM
Figure 23. Human Body Model Current Waveform
RC
50MΩ to 100MΩ
CHARGE-CURRENTLIMIT RESISTOR
HIGHVOLTAGE
DC
SOURCE
Cs
150pF
RD
330Ω
DISCHARGE
RESISTANCE
STORAGE
CAPACITOR
DEVICE
UNDER
TEST
Figure 24. IEC 61000-4-2 ESD Test Model
______________________________________________________________________________________
29
USB On-the-Go Transceivers and Charge Pumps
MAX3301E/MAX3302E
Pin Configurations
N.C.
25
VM
D-
ID_IN
GND
ADD
RESET
INT
N.C.
BOTTOM VIEW
D+
TOP VIEW
24
23
22
21
20
19
18
17
MAX3301E/MAX3302E
16
SUS
26
15
VL
TRM
27
14
SPD
N.C.
28
13
RCV
MAX3301E
VCC
29
12
N.C.
VP
30
11
OE/INT
1
2
3
4
5
6
7
8
N.C.
C-
SE0_VM
GND
SDA
32
VCC
C+
EXPOSED PADDLE
DAT_VP
31
N.C.
VBUS
10
SCL
9
N.C.
D+
D-
ID_IN
GND
ADD
RESET
INT
20
19
18
17
16
15
VM 22
14
SUS
N.C. 23
13
VL
TRM 24
12
SPD
11
RCV
VP 26
10
OE/INT
VBUS 27
9
N.C.
8
SCL
MAX3302E
EXPOSED PADDLE
4
5
6
7
C-
SE0_VM
GND
SDA
VCC
3
N.C.
2
DAT_VP
C+ 28
1
RCV
VL
SUS
GND
SCL
SPD
INT
RESET
C-
SE0_VM
ADD
ID_IN
GND
VCC
DAT_VP
VP
VM
D-
C+
VBUS
VCC
TRM
D+
1
2
3
4
5
B
C
D
UCSP
(2.5mm x 2.5mm)
21
VCC 25
OE/INT
E
TQFN
(5mm x 5mm)
TOP VIEW
SDA
A
TQFN
(4mm x 4mm)
30
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
VL
VCC
1µF
0.1µF
VL(I/O)
VL
*USB OTG SPECIFICATIONS LIMIT
THE TOTAL CAPACITANCE ON VBUS
FROM 1µF (MIN) TO 6.5µF (MAX)
FOR A DUAL-ROLE DEVICE.
VCC
VBUS
DAT_VP
CVBUS*
4.7µF
SE0_VM
RCV
27.4Ω
D+
VP
VM
MAX3301E
MAX3302E
OEV/INT
ASIC
27.4Ω
VBUS
D+
D-
D-
ID_IN
ID
INT
GND
C+
RESET
SUS
CFLYING
0.1µF
SPD
OTG
CONNECTOR
C-
SDA
SCL
ADD
TRM
GND
1µF
______________________________________________________________________________________
31
MAX3301E/MAX3302E
Typical Operating Circuit
Package Information
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
QFN THIN.EPS
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
D2
D
MARKING
b
CL
0.10 M C A B
D2/2
D/2
k
L
AAAAA
E/2
E2/2
CL
(NE-1) X e
E
DETAIL A
PIN # 1
I.D.
e/2
E2
PIN # 1 I.D.
0.35x45°
e
(ND-1) X e
DETAIL B
e
L1
L
CL
CL
L
L
e
e
0.10 C
A
C
0.08 C
A1 A3
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
-DRAWING NOT TO SCALE-
32
21-0140
______________________________________________________________________________________
I
1
2
USB On-the-Go Transceivers and Charge Pumps
COMMON DIMENSIONS
EXPOSED PAD VARIATIONS
PKG.
16L 5x5
20L 5x5
28L 5x5
32L 5x5
40L 5x5
SYMBOL MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX. MIN. NOM. MAX.
A
A1
A3
b
D
E
e
0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80 0.70 0.75 0.80
0
0.02 0.05
0
0.02 0.05
0
0.02 0.05
0
0.02 0.05
0
0.02 0.05
0.20 REF.
0.20 REF.
0.20 REF.
0.20 REF.
0.20 REF.
0.25 0.30 0.35 0.25 0.30 0.35 0.20 0.25 0.30 0.20 0.25 0.30 0.15 0.20 0.25
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10 4.90 5.00 5.10
0.65 BSC.
0.50 BSC.
0.40 BSC.
0.50 BSC.
0.80 BSC.
- 0.25 - 0.25 - 0.25 0.35 0.45
0.25 - 0.25 0.30 0.40 0.50 0.45 0.55 0.65 0.45 0.55 0.65 0.30 0.40 0.50 0.40 0.50 0.60
L1
- 0.30 0.40 0.50
40
N
20
28
32
16
ND
10
4
5
7
8
10
5
7
8
4
NE
----WHHC
WHHD-1
WHHD-2
WHHB
JEDEC
k
L
NOTES:
1. DIMENSIONING & TOLERANCING CONFORM TO ASME Y14.5M-1994.
2. ALL DIMENSIONS ARE IN MILLIMETERS. ANGLES ARE IN DEGREES.
3. N IS THE TOTAL NUMBER OF TERMINALS.
PKG.
CODES
T1655-2
T1655-3
T1655N-1
T2055-3
D2
3.00
3.00
3.00
3.00
3.00
T2055-4
T2055-5
3.15
T2855-3
3.15
T2855-4
2.60
T2855-5
2.60
3.15
T2855-6
T2855-7
2.60
T2855-8
3.15
T2855N-1 3.15
T3255-3
3.00
T3255-4
3.00
T3255-5
3.00
T3255N-1 3.00
T4055-1
3.20
4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL
CONFORM TO JESD 95-1 SPP-012. DETAILS OF TERMINAL #1 IDENTIFIER ARE
OPTIONAL, BUT MUST BE LOCATED WITHIN THE ZONE INDICATED. THE TERMINAL #1
IDENTIFIER MAY BE EITHER A MOLD OR MARKED FEATURE.
L
E2
exceptions
MIN. NOM. MAX. MIN. NOM. MAX. ±0.15
3.10
3.10
3.10
3.10
3.10
3.25
3.25
2.70
2.70
3.25
2.70
3.25
3.25
3.10
3.10
3.10
3.10
3.30
3.20
3.20
3.20
3.20
3.20
3.35
3.35
2.80
2.80
3.35
2.80
3.35
3.35
3.20
3.20
3.20
3.20
3.40
3.00
3.00
3.00
3.00
3.00
3.15
3.15
2.60
2.60
3.15
2.60
3.15
3.15
33.00
33.00
3.00
3.00
3.20
3.10
3.10
3.10
3.10
3.10
3.25
3.25
2.70
2.70
3.25
2.70
3.25
3.25
3.10
3.10
3.10
3.10
3.30
3.20
3.20
3.20
3.20
3.20
3.35
3.35
2.80
2.80
3.35
2.80
3.35
3.35
3.20
3.20
3.20
3.20
3.40
**
**
**
**
**
0.40
**
**
**
**
**
0.40
**
**
**
**
**
**
DOWN
BONDS
ALLOWED
YES
NO
NO
YES
NO
YES
YES
YES
NO
NO
YES
YES
NO
YES
NO
YES
NO
YES
** SEE COMMON DIMENSIONS TABLE
5. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN
0.25 mm AND 0.30 mm FROM TERMINAL TIP.
6. ND AND NE REFER TO THE NUMBER OF TERMINALS ON EACH D AND E SIDE RESPECTIVELY.
7. DEPOPULATION IS POSSIBLE IN A SYMMETRICAL FASHION.
8. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS.
9. DRAWING CONFORMS TO JEDEC MO220, EXCEPT EXPOSED PAD DIMENSION FOR
T2855-3 AND T2855-6.
10. WARPAGE SHALL NOT EXCEED 0.10 mm.
11. MARKING IS FOR PACKAGE ORIENTATION REFERENCE ONLY.
12. NUMBER OF LEADS SHOWN ARE FOR REFERENCE ONLY.
13. LEAD CENTERLINES TO BE AT TRUE POSITION AS DEFINED BY BASIC DIMENSION "e", ±0.05.
-DRAWING NOT TO SCALE-
PACKAGE OUTLINE,
16, 20, 28, 32, 40L THIN QFN, 5x5x0.8mm
21-0140
I
2
2
______________________________________________________________________________________
33
MAX3301E/MAX3302E
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
Package Information (continued)
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
24L QFN THIN.EPS
MAX3301E/MAX3302E
USB On-the-Go Transceivers and Charge Pumps
PACKAGE OUTLINE,
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm
21-0139
E
1
2
PACKAGE OUTLINE,
12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm
21-0139
34
E
2
2
______________________________________________________________________________________
USB On-the-Go Transceivers and Charge Pumps
25L, UCSP.EPS
(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,
go to www.maxim-ic.com/packages.)
PACKAGE OUTLINE, 5x5 UCSP
21-0096
H
1
1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 35
© 2006 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products, Inc.
MAX3301E/MAX3302E
Package Information (continued)