ISO2-CMOS ST-BUS FAMILY MT9092 Digital Telephone with HDLC (HPhone-II) Features ISSUE 2 • Programmable µ-Law/A-Law codec and filters • Programmable CCITT (G.711)/sign-magnitude coding • Programmable transmit, receive and side-tone gains • DSP-based: • i) Speakerphone switching algorithm ii) DTMF and single tone generator iii) Tone Ringer Differential interface to telephony transducers • Differential audio paths • Single 5 volt power supply • X.25 Level 2 HDLC data formatting Applications • Fully featured digital telephone sets • Cellular phone sets • Local area communications stations DSTo DSTi F0i Digital Signal Processor AAAA AAAAAAAAAAAAAA AAAAAAAA AA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AA AAAA AAAA 22.5/-72dB AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAA AAAA AAAA AAAA AAAA AAAA AA AAAAAAAA∆1.5dB AA AAAA AAAA AAAA AAAAAAAA AA AAAA AAAA AAAA Tx & Rx AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAA AA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAA AA May 1995 Ordering Information MT9092AP 44 Pin PLCC -40°C to +85°C Description The MT9092 HPhone-II is a fully featured integrated digital telephone circuit which includes an HDLC data formatter. Voice band signals are converted to digital PCM and vice versa by a switched capacitor Filter/Codec. The Filter/Codec uses an ingenious differential architecture to achieve low noise operation over a wide dynamic range with a single 5V supply. A Digital Signal Processor provides handsfree speaker-phone operation. The DSP is also used to generate tones (DTMF, Ringer and Call Progress) and control audio gains. Internal registers are accessed through a serial microport conforming to INTEL MCS-51™ specifications. The device is fabricated in Mitel's low power ISO2-CMOS technology. Filter/Codec Gain AAAA AAAAAAAAAAAAAAAAAA AAAAAAAA AAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAA AAAAAA 7dB AAAA AAAA AAAAENCODER AAAAAAAA AAAAAAAA AAAAAAAA AAAAAAAA AAAAAA AAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAAA AAAADECODER AAAA AAAA AAAA AAAA AAAA -7dB AAAA AAAAAAAAAAAA AAAAAA AAAAAAAA AAAA AAAA AAAA AAAA AAAAAAAAAAAAAAAAAAAAAAAA AAAAA MICTransducer Interface MIC+ MM+ C4i VSSD HSPKR+ STATUS Control Registers C-Channel Registers HSPKRSPKR+ VDD VSSA SPKR- HDLC VSS SPKR New Call Tone Generator Timing Circuits VBias VRef S/P & P/S Converter LCD Driver S1 S12 BP Serial Port (MCS-51 Compatible) DATA 2 DATA 1 SCLK CS IRQ WD PWRST IC Figure 1 - Functional Block Diagram 7-3 6 5 4 3 2 1 44 43 42 41 40 PWRST IC VRef VBias NC M+ MVSSA MIC+ MICVSS SPKR MT9092 7 8 9 10 11 12 13 14 15 16 17 39 38 37 36 35 34 33 32 31 30 29 SPKR+ SPKRHSPKR+ HSPKRVDD BP S12 S11 S10 S9 S8 IC NC NC VSSD S1 S2 S3 S4 S5 S6 S7 18 19 20 21 22 23 24 25 26 27 28 DSTi DSTo C4i F0i VSSD IRQ SCLK DATA 2 DATA 1 CS WD 44 PIN PLCC Figure 2 - Pin Connections Pin Description Pin # Name 1 M+ Non-Inverting Microphone (Input). Non-inverting input to microphone amplifier from the handset microphone. 2 NC No Connect. No internal connection to this pin. 3 VBias Bias Voltage (Output). (VDD/2) volts is available at this pin for biasing external amplifiers. Connect 0.1 µF capacitor to VSSA. 4 VRef Reference voltage for codec (Output). Nominally [(VDD/2)-1.5] volts. Used internally. Connect 0.1 µF capacitor to VSSA. 5 IC 6 7-4 Description Internal Connection. Tie externally to VSS for normal operation. PWRST Power-up Reset (Input). CMOS compatible input with Schmitt Trigger (active low). 7 DSTi ST-BUS Serial Stream (Input). 2048 kbit/s input stream composed of 32 eight bit channels; the first four of which are used by the MT9092. Input level is TTL compatible. 8 DSTo ST-BUS Serial Stream (Output). 2048 kbit/s output stream composed of 32 eight bit channels. The MT9092 sources digital signals during the appropriate channel, time coincident with the channels used for DSTi. 9 C4i 4096 kHz Clock (Input). CMOS level compatible. 10 F0i Frame Pulse (Input). CMOS level compatible. This input is the frame synchronization pulse for the 2048 kbit/s ST-BUS stream. 11 VSSD Digital Ground . Nominally 0 volts. 12 IRQ Interrupt Request (Open Drain Output). An active low output indicating an unmasked HDLC interrupt event. Requires 1 kΩ pull-up to VDD. 13 SCLK Serial Port Synchronous Clock (Input). Data clock for MCS-51 compatible microport. TTL level compatible. MT9092 Pin Description (continued) Pin # Name Description 14 DATA 2 Serial Data Transmit. In an alternate mode of operation, this pin is used for data transmit from MT9092. In the default mode, serial data transmit and receive are performed on the DATA 1 pin and DATA 2 is tri-stated. 15 DATA 1 Bidirectional Serial Data. Port for microprocessor serial data transfer compatible with MCS51 standard (default mode). In an alternate mode of operation , this pin becomes the data receive pin only and data transmit is performed on the DATA 2 pin. Input level TTL compatible. 16 CS Chip Select (Input). This input signal is used to select the device for microport data transfers. Active low. (TTL level compatible.) 17 WD Watchdog (Output). Watchdog timer output. Active high. 18 IC Internal Connection. Tie externally to VSS for normal operation. 19, 20 NC No Connection. No internal connection to these pins. 21 VSSD 2233 Digital Ground. Nominally 0 volts. S1-S12 Segment Drivers (Output). 12 independently controlled, two level, LCD segment drivers. An in-phase signal, with respect to the BP pin, produces a non-energized LCD segment. An outof-phase signal, with respect to the BP pin, energizes its respective LCD segment. 34 BP Backplane Drive (Output). A two-level output voltage for biasing an LCD backplane. 35 VDD Positive Power Supply (Input). Nominally 5 volts. 36 HSPKR- Inverting Handset Speaker (Output). Output to the handset speaker (balanced). 37 HSPKR Non-Inverting Handset Speaker (Output). Output to the handset speaker (balanced). + 38 SPKR- 39 SPKR+ Non-Inverting Speaker (Output). Output to the speakerphone speaker (balanced). Inverting Speaker (Output). Output to the speakerphone speaker (balanced). 40 VSS SPKR Power Supply Rail for Analog Output Drivers. Nominally 0 Volts. 41 MIC- Inverting Handsfree Microphone (Input). pin. 42 MIC+ Non-inverting Handsfree Microphone (Input). inverting input pin. 43 VSSA Analog Ground. Nominally 0 V. 44 M- Handsfree microphone amplifier inverting input Handsfree microphone amplifier non- Inverting Microphone (Input). Inverting input to microphone amplifier from the handset microphone. NOTES: Intel and MCS-51 are registered trademarks of Intel Corporation, Santa Clara, CA, USA. 7-5 MT9092 Overview The functional block diagram of Figure 1 depicts the main operations performed within the HPhone-II. Each of these functional blocks will be described in the sections to follow. This overview will describe some of the end-user features which may be implemented as a direct result of the level of integration found within the HPhone-II. The main feature required of a digital telephone is to convert the digital Pulse Code Modulated (PCM) information, being received by the telephone set, into an analog electrical signal. This signal is then applied to an appropriate audio transducer such that the information is finally converted into intelligible acoustic energy. The same is true of the reverse direction where acoustic energy is converted first into an electrical analog and then digitized (into PCM) before being transmitted from the set. Along the way if the signals can be manipulated, either in the analog or the digital domains, other features such as gain control, signal generation and filtering may be added. More complex processing of the digital signal is also possible and is limited only be the processing power available. One example of this processing power may be the inclusion of a complex handsfree switching algorithm. Finally, most electroacoustic transducers (loudspeakers) require a large amount of power to develop an effective acoustic signal. The inclusion of audio amplifiers to provide this power is required. The HPhone-II features Digital Signal Processing (DSP) of the voice encoded PCM, complete Analog/ Digital and Digital/Analog conversion of audio signals (Filter/CODEC) and an analog interface to the external world of electro-acoustic devices (Transducer Interface). These three functional blocks combine to provide a standard full-duplex telephone conversation utilizing a common handset. Selecting transducers for handsfree operation, as well as allowing the DSP to perform its handsfree switching algorithm, is all that is required to convert the fullduplex handset conversation into a half-duplex speakerphone conversation. In each of these modes, full programmability of the receive path and side-tone gains is available to set comfortable listening levels for the user as well as transmit path gain control for setting nominal transmit levels into the network. The HPhone-II’s HDLC block is easy to use in proprietary signalling protocols such as those within PABXs and Key Systems. A fully interrupt driven interface, buffered by 19 byte FIFOs in each direction, simplifies the microcontroller's asynchronous access to the D-Channel information. 7-6 The ability to generate tones locally provides the designer with a familiar method of feedback to the telephone user as they proceed to set-up, and ultimately, dismantle a telephone conversation. Also, as the network slowly evolves from the dial pulse/ DTMF methods to the D-Channel protocols it is essential that the older methods be available for backward compatibility. As an example; once a call has been established, say from your office to your home, using the D-Channel signalling protocol it may be necessary to use in-band DTMF signalling to manipulate your personal answering machine in order to retrieve messages. Thus the locally generated tones must be of network quality and not just a reasonable facsimile. The HPhone-II DSP can generate the required tone pairs as well as single tones to accommodate any in-band signalling requirement. Each of the programmable parameters within the functional blocks is accessed through a serial microcontroller port compatible with Intel MCS-51 specifications. Functional Description In this section, each functional block within the HPhone-II is described along with all of the associated control/status bits. Each time a control/ status bit(s) is described it is followed by the address register where it will be found. The reader is referred to the section titled ‘Register Summary' for a complete listing of all address map registers, the control/status bits associated with each register and a definition of the function of each control/status bit. The Register Summary is useful for future reference of control/status bits without the need to locate them within the text of the functional descriptions. Filter-CODEC The Filter/CODEC block implements conversion of the analog 3.3kHz speech signals to/from the digital domain compatible with 64kb/s PCM B-Channels. Selection of companding curves and digital code assignment are register programmable. These are CCITT G.711 A-law or µ-Law, with true-sign/ Alternate Digit Inversion or true-sign/Inverted Magnitude coding, respectively. Optionally, signmagnitude coding may also be selected for proprietary applications. The Filter/CODEC block also implements transmit and receive audio path gains in the analog domain. These gains are in addition to the digital gain pad provided in the DSP section and provide an overall path gain resolution of 0.5dB. A programmable gain, MT9092 voice side-tone path is also included to provide proportional transmit speech feedback to the handset receiver so that a dead sounding handset is not encountered. Figure 3 depicts the nominal halfchannel and side-tone gains for the HPhone-II. On PWRST (pin 6) the Filter/CODEC defaults such that the side-tone path, dial tone filter and 400Hz transmit filter are off, all programmable gains are set to 0dB and µ-Law companding is selected. Further, the Filter/CODEC is powered down due to the PuFC bit (Transducer Control Register, address 0Eh) being reset. This bit must be set high to enable the Filter/ CODEC. The internal architecture is fully differential to provide the best possible noise rejection as well as to allow a SERIAL PORT DSP GAIN* FILTER/CODEC wide dynamic range from a single 5 volt supply design. This fully differential architecture is continued into the Transducer Interface section to provide full chip realization of these capabilites. A reference voltage (V Ref), for the conversion requirements of the CODER section, and a bias voltage (VBias), for biasing the internal analog sections, are both generated on-chip. V Bias is also brought to an external pin so that it may be used for biasing any external gain plan setting amplifiers. A 0.1µF capacitor must be connected from VBias to analog ground at all times. Likewise, although VRef may only be used internally, a 0.1µF capacitor from the VRef pin to ground is required at all times. It is suggested that the analog ground reference point for these two capacitors be physically the same point. TRANSDUCER INTERFACE µ-Law –6.3 dB Α-Law –3.7 dB Receiver Driver Receive PCM –72 to +22.5 dB (1.5dB steps) Receive Filter Gain 0 to –7 dB (1 dB steps) Side-tone –9.96 to +9.96dB (3.32 dB steps) DTMF, Tone Ringer & Handsfree -6 dB Handset Receiver (150Ω) -6 dB HSPKR+ 75 HSPKR– 75 Speaker Phone Driver 0.2dB* Speaker Gain 0 to –24 dB (8 dB steps) SPKR+ SPKR– Speakerphone Speaker (40Ω nominal) (32Ω min) Tone Ringer (input from DSP) Side-tone Nominal Gain µ-Law –11 dB Α-Law –18.8 dB PCM –72 to +22.5 dB (1.5dB steps) Transmit DIGITAL DOMAIN Transmit Filter Gain 0 to +7dB (1 dB steps) µ-Law 6.1dB Α-Law 15.4dB Transmit Gain M U X MIC+ Handsfree MIC– mic M+ M– Transmitter microphone ANALOG DOMAIN Internal to Device External to Device Note: *gain the same for A-Law and µ−Law Figure 3 - Audio Gain Partitioning 7-7 MT9092 To facilitate this the VRef and VBias pins are situated on adjacent pins. Both of these reside in the General Control Register (address 0Fh). The transmit filter is designed to meet CCITT G.714 specifications. The nominal gain for this filter path is 0dB (gain control = 0dB). An anti-aliasing filter is included. This is a second order lowpass implementation with a corner frequency at 25kHz. Attenuation is better than 32dB at 256 kHz and less than 0.01dB within the passband. Digital Signal Processor An optional 400Hz high-pass function may be included into the transmit path by enabling the Tfhp bit in the Transducer Control Register (address 0Eh). This option allows the reduction of transmitted background noise such as motor and fan noise. The receive filter is designed to meet CCITT G.714 specifications. The nominal gain for this filter path is 0 dB (gain control = 0dB). Filter response is peaked to compensate for the sinx/x attenuation caused by the 8kHz sampling rate. The Rx filter function can be altered by enabling the DIAL EN control bit in the Transducer Control Register (address 0Eh). This causes another lowpass function to be added, with a 3dB point at 1000Hz. This function is intended to improve the sound quality of digitally generated dial tone received as PCM. Transmit sidetone is derived from the Tx filter and is subject to the gain control of the Tx filter section. Sidetone is summed into the receive path after the Rx filter gain control section so that Rx gain adjustment will not affect sidetone levels. The sidetone path may be enabled/disabled with the SIDE EN bit located in the Transducer Control Register (address 0Eh). See also STG0-STG2 (address 0Bh). Transmit and receive filter gains are controlled by the TxFG0-TxFG2 and RxFG0-RxFG2 control bits respectively. These are located in the FCODEC Gain Control Register 1 (address 0Ah). Transmit filter gain is adjustable from 0dB to +7dB and receive filter gain from 0dB to -7dB, both in 1dB increments. Side-tone filter gain is controlled by the STG 0-STG2 control bits located in the FCODEC Gain Control Register 2 (address 0Bh). Side-tone gain is adjustable from -9.96dB to +9.96dB in 3.32dB increments. Law selection for the Filter/CODEC is provided by the A/µ companding control bit while the coding scheme is controlled by the sign-mag/CCITT bit. 7-8 The DSP block is located, functionally, between the serial ST-BUS port and the Filter/CODEC block. Its main purpose is to provide both a digital gain control and a half-duplex handsfree switching function. The DSP will also generate the digital patterns required to produce standard DTMF signalling tones as well as single tones and a tone ringer output. A programmable (ON/OFF) offset null routine may also be performed on the transmit PCM data stream. The DSP can generate a ringer tone to be applied to the speakerphone speaker during normal handset operation so that the existing call is not interrupted. The main functional control of the DSP is through two hardware registers which are accessible at any time via the microport. These are the Receive Gain Control Register at address 1Dh and the DSP Control Register at address 1Eh. In addition, other functional control is accomplished via multiple RAMbased registers which are accessible only while the DSP is held in a reset state. This is accomplished with the DRESET bit of the DSP Control Register. Ram-based registers are used to store transmit gain levels (20h for transmit PCM and 21h for transmit DTMF levels), the coefficients for tone and ringer generation (addresses 23h and 24h), and tone ringer warble rates (address 26h). All undefined addresses below 20h are reserved for the temporary storage of interim variables calculated during the execution of the DSP algorithms. These undefined addresses should not be written to via the microprocessor port. The DSP can be programmed to execute the following micro-programs which are stored in instruction ROM, (see PS0 to PS2, DSP Control Register, address 1Eh). All program execution begins at the frame pulse boundary. PS2 PS1 PS0 Micro-program 0 0 0 Power up reset program 0 0 1 Transmit and receive gain control program; with autonulling of the transmit PCM, if the AUTO bit is set (see address 1Dh) 0 1 0 DTMF generation plus transmit and receive gain control program (autonull available via the AUTO control bit) 0 1 1 Tone ringer plus transmit and receive gain control program (autonull available via the AUTO control bit) MT9092 PS2 1 1 PS1 PS0 0 0 0 1 1 1 0 1 1 1 Note: Micro-program Optional Offset Nulling handsfree switching program Last three selections reserved For the DSP to function it must be selected to operate, in conjunction with the Filter/Codec, in one of the B-Channels. Therefore, one of the BChannel enable bits must be set (see Timing Control, address 15h : bits CH2EN and CH 3EN). Power Up reset Program A hardware power-up reset (pin 6, PWRST) will initialize the DSP hardware registers to the default values (all zeros) and will reset the DSP program counter. The DSP will then be disabled and the PCM streams will pass transparently through the DSP. The RAM-based registers are not reset by the PWRST pin but may be initialized to their default settings by programming the DSP to execute the power up reset program. None of the micro-programs actually require the execution of the power up reset program but it is useful for pre-setting the variables to a known condition. Note that the reset program requires one full frame (125µSec) for execution. Gain Control Program Gain control is performed on converted linear code for both the receive and the transmit PCM. Receive gain control is set via the hardware register at address 1Dh (see bits B0 - B5) and may be changed at any time. Gain in 1.5dB increments is available within a range of +22.5dB to -72dB. Normal operation usually requires no more than a +20 to -20 dB range of control. However, the handsfree switching algorithm requires a large attenuation depth to maintain stability in worst case environments, hence the large (-72 dB) negative limit. Transmit gain control is divided into two RAM registers, one for setting the network level of transmit speech (address 20h) and the other for setting the transmit level of DTMF tones into the network (address 21h). Both registers provide gain control in 1.5dB increments and are encoded in the same manner as the receive gain control register (see address 1Dh, bits B0 - B5). The power up reset program sets the default values such that the receive gain is set to -72.0 dB, the transmit audio gain is set to 0.0dB and the transmit DTMF gain is set to -3.0 dB (equivalent to a DTMF output level of -4dBm0 into the network). Transmit PCM may contain residual offset in the form of a DC component. An offset of up to ±fifteen linear bits is acceptable with no degradation of the parameters defined in CCITT G.714. The HPhone-II filter/CODEC guarantees no more than ±ten linear bits of offset in the transmit PCM when the autonull routine is not enabled. By enabling autonulling (see AUTO in the Receive Gain Control Register, address 1Dh) offsets are reduced to within ±one bit of zero. Autonulling circuitry was essential in the first generations of Filter/Codecs to remove the large DC offsets found in the linear technology. Newer technology has made nulling circuitry optional as offered in the HPhone-II. DTMF and Gain Control Program The DTMF program generates a dual cosine wave pattern which may be routed into the receive path as comfort tones or into the transmit path as network signalling. In both cases, the digitally generated signal will undergo gain adjustment as programmed into the Receive Gain Control and the Transmit DTMF Gain Control registers. The composite signal output level in both directions is -4dBm0 when the gain controls are set to 2Eh (-3.0 dB). Adjustments to these levels may be made by altering the settings of the gain control registers. Pre-twist of 2.0dB is incorporated into the composite signal. The frequency of the low group tone is programmed by writing an 8-bit coefficient into Tone Coefficient Register 1 (address 23h), while the high group tone frequency uses the 8-bit coefficient programmed into Tone Coefficient Register 2 (address 24h). Both coefficients are determined by the following equation: COEFF = 0.128 x Frequency (in Hz) where COEFF is a rounded off 8 bit binary integer A single frequency tone may be generated instead of a dual tone by programming the coefficient at address 23h to a value of zero. In this case the frequency of the single output tone is governed by the coefficient stored at address 24h. 7-9 MT9092 Table 1 gives the standard DTMF frequencies, the coefficient required to generate the closest frequency, the actual frequency generated and the percent deviation of the generated tone from the nominal. Frequency (Hz) COEF Actual Frequency % Deviation 697 59h 695.3 -.20% 770 63h 773.4 +.40% 852 6Dh 851.6 -.05% 941 79h 945.3 +.46% 1209 9Bh 1210.9 +.20% 1336 ABh 1335.9 .00% 1477 BDh 1476.6 -.03% 1633 D1h 1632.8 -.01% Table 1 DTMF Signal to distortion: The sum of harmonic and noise power in the frequency band from 50Hz to 3500Hz is typically more than 30dB below the power in the tone pair. All individual harmonics are typically more than 40dB below the level of the low group tone. Tone Ringer and Gain Control Program A locally generated alerting (ringing) signal is used to prompt the user when an incoming call must be answered. The DSP uses the values programmed into Tone Coefficient Registers 1 and 2 (addresses 23h and 24h) to generate two different squarewave frequencies in PCM code. The amplitude of the squarewave frequencies is set to a mid level before being sent to the receive gain control block. From there the PCM passes through the decoder and receive filter, replacing the normal receive PCM data, on its way to the loudspeaker driver. Both coefficients are determined by the following equation: COEFF = 8000/Frequency (Hz) where COEFF is a rounded off 8 bit binary integer. The ringer program switches between these two frequencies at a rate defined by the 8-bit coefficient programmed into the Tone Ringer Warble Rate Register (address 26h). The warble rate is defined by the equation: Tone duration (warble frequency in Hz) = 500/COEFF where 0 < COEFF < 256, a warble rate of 5-20Hz is suggested. 7-10 An alternate method of generating ringer tones to the speakerphone speaker is available. With this method the normal receive speech path through the decoder and receive filter is uninterrupted to the handset, allowing an existing conversation to continue. The normal DSP and Filter/CODEC receive gain control is also retained by the speech path. When the OPT bit (DSP Control Register address 1Eh) is set high the DSP will generate the new call tone according to the coefficients programmed into registers 23h, 24h and 26h as before. In this mode the DSP output is no longer a PCM code but a toggling signal which is routed directly through the New Call Tone gain control section to the loudspeaker driver. Refer to the section titled ‘New Call Tone’. Handsfree Program A half-duplex speakerphone program, fully contained on chip, provides high quality gain switching of the transmit and receive speech PCM to maintain loop stability under most network and local acoustic environments. Gain switching is performed in continuous 1.5dB increments and operates in a complimentary fashion. That is, with the transmit path at maximum gain the receive path is fully attenuated and vice versa. This implies that there is a mid position where both transmit and receive paths are attenuated equally during transition. This is known as the idle state. Of the 64 possible attenuator states, the algorithm may rest in only one of three stable states; full receive, full transmit and idle. The maximum gain values for full transmit and full receive are programmable through the microport at addresses 20h and 1Dh respectively, as is done for normal handset operation. This allows the user to set the maximum volumes to which the algorithm will adhere. The algorithm determines which path should maintain control of the loop based upon the relative levels of the transmit and receive audio signals after the detection and removal of background noise energy. If the algorithm determines that neither the transmit or the receive path has valid speech energy then the idle state will be sought. The present state of the algorithm plus the result of the Tx vs. Rx decision will determine which transition the algorithm will take toward its next stable state. The time durations required to move from one stable state to the next are parameters defined in CCITT Recommendation P.34 and are used by default by this algorithm (i.e., build-up time, hang-over time and switching time). MT9092 Quiet Code The DSP can be made to send quiet code to the decoder and receive filter path by setting the RxMUTE bit high. Likewise, the DSP will send quiet code in the transmit (DSTo) path when the TxMUTE bit is high. Both of these control bits reside in the DSP Control Register at address 1Eh. When either of these bits are low, their respective paths function normally. HDLC The High-level Data Link Control (HDLC) block is located, functionally, between the serial ST-BUS port and the serial Microcontroller port. This functional block handles the bit oriented protocol requirements of layer 2 X.25 packet switching and Q.921 link access protocols defined by CCITT. The HDLC is dedicated to D-Channel operation at 16kb/s and offers buffered access to the serial D-Channel data through separate 19 byte transmit and receive FIFOs. The HDLC generates and detects the flags, various link channel states and abort sequences as well as performing a cyclic redundancy check on data packets according to the CCITT defined polynomial. Lastly, the protocol functions may be disabled to provide transparent access, of the serial port DChannel, to the microport. A power up reset (PWRST, pin 6) or a software reset via RST (address 0Fh) will cause the HDLC transceiver to be initialized. This results in the transmitter and receiver being disabled and all HDLC registers defaulting to their power reset values. HDLC Frame Structure A valid HDLC frame begins with an opening flag, contains at least 16 bits of address, control or information, ends with a 16 bit FCS followed by a closing flag. Data formatted in this manner is also referred to as a "packet". Refer to Figure 4. FLAG DATA FIELD FCS FLAG One Byte n Bytes (n≥2) Two Bytes One Byte Figure 4 - Frame Format Flag Sequence All HDLC frames start and end with a unique sequence of 8 bits. This sequence is 0111 1110 (7Eh). The closing flag of one frame can be the opening flag of the next frame. The transmitter generates flags and appends them to the packet to be transmitted. The receiver searches the incoming data stream for flags on a bit-by-bit basis to establish frame synchronization. The receiver uses flags for synchronization only and does not transfer them to the Rx FIFO. Address Field The address field consists of one or two 8-bit bytes directly following the opening flag. Address, Control and Information fields are known collectively as the Data field. Control Field The control field consists of one 8-bit byte directly following the address field. The HDLC does not distinguish between the control field and the information field. Information Field The information field immediately follows the control field and consists of N bytes of data where one byte contains 8 bits. A packet does not need to contain an information field to be valid. The HDLC does not distinguish between the control field and the information field. Frame Checking Sequence Field The 16 bits preceding a closing flag are the FCS field. A cyclic redundancy check utilizing the CRCCCITT standard generator polynomial X 16 + X12 +X5 +1 produces the 16-bit FCS. In the transmitter the FCS is calculated on all bits of the address, control and information fields. The complement of the FCS is transmitted, most significant bit first, in the FCS field. The receiver calculates the FCS on the incoming packet's address, control, information and FCS fields and compares the result to 'F0B8'. This result verifies no transmission errors occurred. If the packet, between flags, is also at least 32 bits in length then the address, control and information field data are entered into the receive FIFO minus the FCS which is discarded. Order of Bit Transmission Address, control and information field data are entered into the transmit FIFO. This data is then transmitted and received on the serial bus least significant bit first. The FCS is sent most significant bit first on the serial bus. Note that it is the complement of the calculated FCS which is transmitted. The HDLC does not distinguish ADDRESS/CONTROL/INFORMATION bytes except 7-11 MT9092 to determine if the packet is of minimum valid length. These fields are transferred transparently through the FIFO's. transmitted packet. If this happens, then the last data written to the receive FIFO will not correspond exactly with the last byte received before the frame abort. Data Transparency (Zero insertion/deletion) Interframe Time Fill and Link Channel States Transparency ensures that the contents of a data packet do not imitate a flag, go-ahead, frame abort or idle channel. The contents of a transmitted frame, between the flags, is examined on a bit-by-bit basis and a 0 bit is inserted after all sequences of five contiguous 1 bits (including the last five bits of the FCS). Upon receiving five contiguous 1s within a frame the receiver deletes the following 0 bit. When the HDLC transmitter is not sending packets it will wait in one of two states. Interframe Time Fill: This is a continuous series of flags occurring between frames indicating that the channel is active but that no data is being sent. Invalid Frames A frame is invalid if one of the following four conditions exists. Inserted zeros are not part of a valid bit count: 1. If the FCS pattern generated from the received data does not match the 'F0B8' pattern then the last data byte of the packet is written to the receive FIFO with a 'bad packet' indication. 2. A short frame exists if there are less than 25 bits between the flags. Short frames are ignored by the receiver and nothing is written into the receive FIFO. 3. Packets which are at least 25 bits in length but less than 32 bits (between the flags) are also invalid. In this case the data is written to the FIFO but the last byte is tagged with a 'bad packet' indication. 4. If a frame abort sequence is detected the packet is invalid. Some or all of the current packet will reside in the receive FIFO, assuming the packet length before the abort sequence was at least 26 bits long. Idle: An idle channel occurs when at least fifteen contiguous 1s are transmitted or received. In both cases the transmitter will exit the wait state when data is loaded into the transmit FIFO. Go-Ahead A go-ahead is defined as the pattern ‘011111110’ (contiguous 7F’s) and is the occurrence of a frame abort sequence followed by a zero, outside of the boundaries of a normal packet. Being able to distinguish a proper (in packet) frame abort sequence from one occurring outside of a packet allows a higher level of signalling protocol which is not part of the HDLC specifications. Transmitter Following initialization and enabling, via the HTxEN bit (address 03h), the transmitter is in the Idle Channel State (Mark Idle). Interframe time fill may be selected by setting the Mark Idle bit (address 03h) high. The transmitter remains in its programmed state until data is written to the Tx FIFO. The transmitter will then proceed as follows: Frame Abort The transmitter will abort a current packet by substituting a zero followed by seven contiguous 1s in place of the normal data. The receiver will abort upon reception of seven contiguous 1s occurring between the flags of a packet which contains at least 26 bits. Note that should the last receive byte before the frame abort end with contiguous 1s, these are included in the seven 1s required for a receiver abort. This means that the location of the abort sequence in the receiver may occur before the location of the abort sequence in the originally 7-12 1) If the transmitter is in the idle state the present byte of ones will be completely transmitted before the opening flag and packet data is sent. 2) If the transmitter is in the interframe time fill state the flag currently being transmitted will be used as the opening flag followed by the packet data. To assist in loading multiple packets into the transmit FIFO the last packet byte is tagged with either EOP (to indicate the end of the current packet) or FA. Control Register 1 (address 03h) bits EOP (end of MT9092 packet) and FA (frame abort) are set before writing the last packet byte to the Tx FIFO. The act of loading the last packet byte will then automatically reset the EOP and FA bits. Tx FIFO bytes are continuously transmitted until the FIFO is empty, by which time an EOP or FA tag should have been encountered by the transmitter. After the last bit of the EOP byte has been transmitted a 16 bit FCS is sent followed by a closing flag. When multiple packets of data are loaded into the Tx FIFO only one flag is sent between packets. When the transmitter encounters a byte tagged FA then a frame abort sequence is sent instead of the tagged byte. All bytes previous to but not including the tagged byte are sent. Command/Address byte which indicates a microport read of address 07h. Since all interrupts are generated by the occurrence of an HDLC event (i.e., a transition), this register informs that an event has occurred but does not guarantee that it is still valid. To determine current validity the HDLC Status Register (address 04h) should be read. Due to the asynchronous nature of the interrupts an interrupt occurring during a read of the Interrupt Status register will be held until the read cycle is over, unless it is an interrupt which is already valid. There are three interrupts associated with the transmitter. TEOP Transmit End Of Packet: Set when the transmitter has finished sending the closing flag of a packet or after an abort sequence has been completed. TxFL Transmit FIFO Low: Set when a transition from 5 to 4 bytes in the Tx FIFO has occurred. This is an early warning to the microprocessor that the FIFO is emptying and should be serviced before it empties completely; a condition which will result in a transmit underrun unless an EOP or FA byte has been written to the FIFO. By setting the Fltx bit (address 05h) high the FIFO emptying condition will occur at the transition from 15 to 14 bytes. This will allow the microport more time to react to this interrupt condition. The transmitter returns to its programmed wait state after concluding the transmission of EOP or FA if the Tx FIFO is empty. Transmit FIFO Status The transmit FIFO is 19 bytes deep (address 02h). As data is loaded into (from the microport) and extracted from (via the serial port) the Tx FIFO the present 'fill state' can be monitored using the Txstat1 and Txstat2 bits found in the HDLC Status Register (address 04h). These states are encoded as shown in Table 2. Note that the FIFO emptying threshold, where an interrupt (TxFL if unmasked) will occur, can be set to a low level 4 (default) or to a high level 14 by the Fltx bit in the HDLC Control Register 2 (address 05h). A Tx FIFO underrun occurs if the Tx FIFO empties without the occurrence of an EOP or FA tagged byte. A frame abort sequence is automatically transmitted under this condition. Transmit Interrupts The HDLC Interrupt Enable Register (address 06h) is used to select (unmask) only those interrupts which are deemed important to the microprocessor. After a PWRST or software RST all enable bits will be cleared causing all interrupts to be masked. All selected interrupt events will cause the IRQ pin to become active. Unselected interrupt events will not cause IRQ to become active however, the event will still be represented by the appropriate bit in the HDLC Interrupt Status Register (address 07h). This register must be read after receiving an IRQ or may be polled at any time. The IRQ output pin is reset coincident with the first SCLK falling edge following a Txunder Transmit underrun: Set when the Tx FIFO empties without the occurrence of an EOP or FA tagged byte. A frame abort sequence is automatically transmitted under this condition. Note that this register bit position is shared with the frame abort (FA) interrupt (see receive interrupts). For this bit to reflect Txunder the Intsel bit in Control Register 2 (address 05h) must be set high. Disabling, Reset, Transparent Operation and CRC Disabling the transmitter via the HTxEn bit will occur after the current packet is completely transmitted. The status and Interrupt registers may still be read and the Tx FIFO and control registers written while the transmitter is disabled. 7-13 MT9092 The Tx FIFO may be reset by setting the Txfrst bit in the HDLC Control Register 2 (address 05h). The HDLC Status Register will identify the Tx FIFO as being empty although the actual data in the FIFO will not be reset. Txfrst will be cleared by the next write to the Tx FIFO. Transparent data may be sent by setting the TRANS bit (address 03h) high. The transmitter will no longer generate the flag, abort and idle sequences, nor will it insert zeros and append the FCS. Data will still be transmitted LSB first. If there is no data in the Tx FIFO or the Tx FIFO empties the last byte transmitted will be repetitively sent until new data is presented to the FIFO. It will take typically two STBUS frames, after writing TRANS, before this mode begins. Note that CH 0EN must also be set. Transmission of the FCS field CRC may be inhibited using the Tcrci (Transmit Crc Inhibit) bit at address 05h. While this bit is set the opening flag followed by the data fields and closing flag is transmitted, including zero insertion, but the calculated CRC is not. This allows the processor to insert the CRC as part of the data field. This usage is for V.120 terminal adaptation for synchronous protocol sensitive UI frames. If address recognition is required, Receive Address Recognition Registers 1 and/or 2 (addresses 00h and 01h respectively) are loaded with the desired address comparison information, the Adrec bit is set high and A1EN and A2EN are set as required. Bit 0 (A1EN and A2EN) of both recognition registers is used as an enable for that byte. When either of these bits are low their respective address mask information is ignored. In this way either or both of the first two received bytes can be compared to the expected mask values. Only those packets passing the appropriate comparison test will be loaded into the Rx FIFO. The appropriate comparison test (single/dual byte address, All-call) is defined by the logic state of bit 0 of the first byte received after the opening flag. Bit 0 of the first received address byte (address extension bit) is monitored to determine if a single or dual byte address is being received. 1. If the address extension bit is 1 then a single byte address is being received. If A1EN is high the stored bit mask (Adr11 - Adr16 and sometimes Adr10) is compared to the received first address byte. Any packet failing this address comparison will not be stored in the Rx FIFO except for the All-call condition. A1EN must be set high for a single-byte All-call (11111111) address to be recognized. The second mask byte is ignored. Seven bits of address comparison may be realized for single byte recognition by setting the SEVEN bit (address 05h) high. This mode will then include Adr10 as part of the mask information. The first received byte must also have bit 0 set to a 1 indicating single byte addressing. 2. If the address extension bit is 0 then a two byte address is being received and the six most significant bits of the first received byte are compared. The seven most significant bits of the second received byte are compared (Adr20 Adr26, note A2EN must be set high also). Any packet failing this address comparison will not be stored in the Rx FIFO. An All-call condition (1111111x) is also monitored for in the second received address byte and, if found, the first and second byte masks are ignored (not compared with the mask byte). Packets addressed with Allcall are written into the Rx FIFO. Receiver Following initialization and enabling, via the HRxEN bit at address 03h, the receiver begins clocking in serial data checking for flags (0111 1110), go-aheads (0111 1111 0), and idle channel states (at least fifteen contiguous ones). Upon detecting a flag the receiver synchronizes itself to the data stream and begins calculating the CRC. If the packet length, between the flags and after zero deletion, is less than 25 bits the packet is ignored and nothing is written to the Rx FIFO. If the packet length, after zero deletion, is between 25 and 31 bits a last byte, bad packet indication is written into the Rx FIFO. Idle Channel When the receiver detects at least 15 contiguous ones it declares an idle channel condition exists and sets the IdleChan bit in the HDLC status register high (address 04h). This bit remains set until the received condition changes. Address Recognition When Adrec (HDLC Control Register 1, address 03h) is low all valid received packets, regardless of the address field information, are loaded into the Rx FIFO. 7-14 In CCITT Q.921 parlance the Adr11 - Adr16 bits are defined as Sapi0 - Sapi5 (Service Access Point Identifier n). Adr10 is defined as C/R (Command/ Response). Adr20 - Adr26 are defined as Tei0 - Tei6 (Terminal Endpoint Identifier n). MT9092 Receive Byte Status As each received packet byte is written into the Rx FIFO two bits are appended to indicate the status of that byte. As these bytes are read from the Rx FIFO the status bits are made available to the microprocessor in the HDLC Status Register (address 04h) as RxBS1 and RxBS2. Since the information contained in RxBS1 & RxBS2 pertains to the byte about to be read from the Rx FIFO, it is important that this information be read before reading the data byte from the FIFO. RxBS1 and RxBS2 are encoded as shown in Table 2. A good packet indication means a good FCS and no frame abort whereas a bad packet indication means either an incorrect FCS or a frame abort occurred. in Table 2. Note that the FIFO filling threshold, where an interrupt (RxFf if unmasked) will occur, can be set to a high level 15 (default) or to a low level 5 by the Flrx bit in the HDLC Control Register 2 (address 05h). In the case of an Rx FIFO overflow, an attempt by the receiver to write data into an already full FIFO, the receiver is disabled causing it to stop writing to the Rx FIFO. The remainder of the current receive packet is therefore ignored. The receiver will be reenabled when the next flag is detected but will overflow again if the Rx FIFO level has not been reduced to less than full. If two 'first byte' (RxBS1 and RxBS2) conditions are observed in the FIFO without an intervening 'last byte' then an overflow occurred for the first packet. Receive FIFO Status Receive Interrupts The receive FIFO is 19 bytes deep (address 02h). As data is loaded into (from the serial port) and extracted from (via the microport) the Rx FIFO the present 'fill state' can be monitored using the Rxstat1 and Rxstat2 bits found in the HDLC Status Register (address 04h). These states are encoded as shown RxBS2, RxBS1 Note - Txstat2, Txstat1 Rxstat2, Rxstat1 The HDLC Interrupt Enable Register (address 06h) is used to select (unmask) only those interrupts which are deemed important to the microprocessor. After a PWRST or software RST all enable bits will be cleared causing all interrupts to be masked. Are status bits from the Rx FIFO. RxBS1 Byte status RxBS2 1 1 last byte (bad packet) 0 1 first byte 1 0 last byte (good packet) 0 0 packet byte If two consecutive first byte signals are received without an intervening last byte, then an overflow has occurred and the first packet (or packets) are bad. A bad packet indicates that either a frame abort had occurred or the FCS did not match. On power-up these bits are in an indeterminate state until the first byte is written to Rx FIFO. These two bits are encoded to indicate the present state of Tx FIFO. This is an asynchronous event. Txstat2 Txstat1 Tx FIFO Status 0 0 TxFULL 0 1 5 OR MORE BYTES (15 if Fltx set) 1 1 4 OR LESS BYTES (14 if Fltx set) 1 0 TxEMPTY These two bits are encoded to indicate the present state of Rx FIFO. This is an asynchronous event. Rxstat2 Rxstat1 Rx FIFO Status 0 0 RxEMPTY 0 1 14 OR LESS BYTES (4 if Flrx set) 1 1 15 OR MORE BYTES (5 if Flrx set) 1 0 RxOVERFLOW EXISTS Table 2 - HDLC Status Bits 7-15 MT9092 All selected interrupt events will cause the IRQ pin to become active. Unselected interrupt events will not cause IRQ to become active however, the event will still be represented by the appropriate bit in the HDLC Interrupt Status Register (address 07h). This register must be read after receiving an IRQ or may be polled at any time. The IRQ output pin is reset coincident with the first SCLK falling edge following a Command/Address byte which indicates a microport read of address 07h. Since all interrupts are generated by the occurrence of an HDLC event (i.e., a transition), this register informs that an event has occurred but does not guarantee that it is still valid. To determine current validity the HDLC Status Register (address 04h) should be read. Due to the asynchronous nature of the interrupts an interrupt occurring during a read of the Interrupt Status register will be held until the read cycle is over, unless it is an interrupt which is already valid. There are six interrupts associated with the receiver. GA Go Ahead: Set when a go-ahead pattern (011111110) has been detected by the receiver. EOPD End Of Packet Detect: Set when an end of packet byte has been written into the Rx FIFO by the receiver. This event may be due to receiving a closing flag, an abort sequence or an invalid packet. EopR End of packet Read: Set when the next byte to be read from the Rx FIFO is the last byte of a packet or when a read to an empty Rx FIFO has occurred. FA Frame Abort: Set when a frame abort sequence is received during packet reception. The aborted packet must contain a minimum of 26 bits for the FA sequence to be recognized. Note that this register bit position is shared with the transmitter under-run (Txunder) interrupt (see transmit interrupts). For this bit to reflect FA the Intsel bit in Control Register 2 (address 05h) must be set low. RxFf - Receive FIFO filling: Set when a transition from 14 to 15 bytes in the Rx FIFO has occurred. This is an early warning to the microprocessor that the FIFO is filling and should be serviced before it 7-16 becomes completely full; a condition which may result in a receive overflow condition. By setting the Flrx bit (address 05h) high the FIFO filling condition will occur when a transition from 4 to 5 bytes occurs. This will allow the microport more time to react to this interrupt condition. RxOvfl - Receive FIFO Overflow: Set when the receiver attempts to write data into an already full Rx FIFO. Under this condition the HDLC will disable the receiver until a new flag is detected. See also Receive FIFO Status. Disabling, Reset and Transparent Operation Disabling of the receiver via the HRxEn bit will occur after the current packet is completely loaded into the Rx FIFO. Disabling can occur during packet reception if no bytes have been written to the Rx FIFO yet. The Rx FIFO, status and Interrupt registers may still be read and control registers written while the receiver is disabled. Note that the receiver requires the reception of a flag before processing a packet, thus if the receiver is enabled in the middle of an incoming packet it will ignore that packet and wait for the next complete one. The Rx FIFO may be reset by setting the Rxfrst bit in the HDLC Control Register 2 (address 05h). The receiver will be disabled until reception of the next flag. The Status Register will identify the Rx FIFO as being empty although the actual data in the FIFO will not be reset. Rxfrst will be cleared by the reception of the next received flag pattern. Data may be received transparently by setting the TRANS bit (address 03h) high. Timing control bit CH 0EN must also be set. The receiver will disable protocol functions such as flag/abort/go-ahead/idle detection, zero deletion, CRC calculation and address comparison. Data is shifted into the Rx FIFO in a byte-wide format. In transparent mode when an Rx FIFO overflow condition occurs the receiver will continue to write data into the Rx FIFO, overwriting the last byte. The overflow interrupt condition can only be detected again if the Rx FIFO is reset (Rxfrst bit at address 05h) since normally the overflow condition is cleared by the reception of the next flag and transparent data is unlikely to emulate a flag. Also, the Rxfrst bit itself will have to be reset by writing it low since it is usually reset automatically by the occurrence of the next flag. MT9092 Transducer Interfaces HSPKR+ Four standard telephony transducer interfaces are provided by the HPhone-II. These are: 75 Ω ➧ ➧ ➧ The handset microphone inputs (transmitter), pins M+/M- and the speakerphone microphone inputs, pins MIC+/MIC-. The transmit path is muted/not-muted by the MIC EN control bit. Selection of which input pair is to be routed to the transmit filter amplifier is acomplished by the MIC/HNSTMIC control bit. Both of these reside in the Transducer Control Register (address 0Eh). The nominal transmit path gain may be adjusted to either 6.1dB (suggested for µ-Law) or 15.4dB (suggested for A-Law). Control of this gain is provided by the MICA/u control bit (General Control Register, address 0Fh). This gain adjustment is in addition to the programmable gain provided by the transmit filter and DSP. The handset speaker outputs (receiver), pins HSPKR+/HSPKR-. This internally compensated, fully differential output driver is capable of driving the load shown in Figure 5. This output is enabled/disabled by the HSSPKR EN bit residing in the Transducer Control Register (address 0Eh). The nominal handset receive path gain may be adjusted to either -12.3dB (suggested for µ-Law) or -9.7dB (suggested for A-Law). Control of this gain is provided by the RxA/u control bit (General Control Register, address 0Fh). This gain adjustment is in addition to the programmable gain provided by the receive filter and DSP. The loudspeaker outputs, pins SPKR+/SPKR-. This internally compensated, fully differential output driver is capable of directly driving 6.5vpp into a 40 ohm load. This output is enabled/ disabled by the SPKR EN bit residing in the Transducer Control Register (address 0Eh). The nominal gain for this amplifier is 0.2dB. 1000 pF 150 ohm load MT9092 (speaker) 75 Ω 1000 pF HSPKR- ground Figure 5- Handset Speaker Driver LCD A twelve segment, non-multiplexed, LCD display controller is provided for easy implementation of various set status and call progress indicators. The twelve output pins (Sn) are used in conjunction with 12 segment control bits, located in LCD Segment Enable Registers 1&2 (addresses 12h and 13h), and the BackPlane output pin (BP) to control the on/off state of each segment individually. The BP pin drives a continuous 62.5Hz, 50% duty cycle squarewave output signal. An individual segment is controlled via the phase relationship of its segment driver output pin with respect to the backplane, or common, driver output. Each of the twelve Segment Enable bits corresponds to a segment output pin. The waveform at each segment pin is in-phase with the BP waveform when its control bit is set to logic zero (segment off) and is out-of-phase with the BP waveform when its control bit is set to a logic high (segment on). Refer to the LCD Driver Characteristics for pin loading information. C-Channel Microport Access to the internal control and status registers of Mitel basic rate, layer 1, transceivers is through the ST-BUS Control Channel (C-Channel), since direct microport access is not usually provided, except in the case of the SNIC (MT8930). The HPhone-II provides asynchronous microport access to the STBUS C-Channel information on both DSTo and DSTi via a double-buffered read/write register (address 14h). Data written to this address is transmitted on the C-Channel every frame when enabled by CH 1EN (see ST-BUS/Timing Control). A serial microport, compatible with Intel MCS-51 (mode 0) specifications, provides access to all HPhone-II internal read and write registers. This microport consists of three pins; a half-duplex transmit/receive data pin (DATA1), a chip select pin (CS) and a synchronous data clock pin (SCLK). On power-up reset (PWRST) or with a software reset (RST), the DATA1 pin becomes a bidirectional (transmit/receive) serial port while the DATA2 pin is internally disconnected and tri-stated. 7-17 MT9092 All data transfers through the microport are two-byte transfers requiring the transmission of a Command/ Address byte followed by the data byte written or read from the addressed register. CS must remain asserted for the duration of this two-byte transfer. As shown in Figure 6, the falling edge of CS indicates to the HPhone-II that a microport transfer is about to begin. The first 8 clock cycles of SCLK after the falling edge of CS are always used to receive the Command/Address byte from the microcontroller. The Command/Address byte contains information detailing whether the second byte transfer will be a read or a write operation and of what address. The next 8 clock cycles are used to transfer the data byte between the HPhone-II and the microcontroller. At the end of the two-byte transfer CS is brought high again to terminate the session. The rising edge of CS will tri-state the output driver of DATA1 which will remain tri-stated as long as CS is high. Lastly, provision is made to seperate the transmit and receive data streams onto two individual pins. This control is given by the DATASEL pin in the General Control Register (address 0Fh). Setting DATASEL logic high will cause DATA1 to become the data receive pin and DATA2 to become the data transmit pin. Only the signal paths are altered by DATASEL; internal timing remains the same in both cases. Tri-stating on DATA2 follows CS as it does on DATA1 when DATASEL is logic low. Use of the DATASEL bit is intended to help in adapting Motorola (SPI) and National Semiconductor (Micro-wire) microcontrollers to the HPhone-II. Note that whereas Intel processor serial ports transmit data LSB first other processor serial ports, including Motorola, transmit data MSB first. It is the responsibility of the microcontroller to provide LSB first data to the HPhone-II. ST-BUS/Timing Control Receive data is sampled and transmit data is made available on DATA1 concurrent with the falling edge of SCLK. An open-drain interrupt request (IRQ) output provides a method for interrupting the microcontroller when an unmasked HDLC event occurs within the HPhone-II. IRQ remains active until the HDLC Interrupt Status Register is read or a (hardware/software) reset occurs. More detail is provided in the section pertaining to the HDLC functional block. COMMAND/ADDRESS ➄ DATA 1 Receive D0 D1 D2 D3 D4 D5 D6 D7 DATA 1 or DATA 2 Transmit ➀ A serial link is required for the transport of data between the HPhone-II and the external digital transmission device. The HPhone-II utilizes the STBUS architecture defined by Mitel Semiconductor. Refer to Mitel Application Note MSAN-126. The HPhone-II ST-BUS consists of output and input serial data streams, DSTo and DSTi respectively, a synchronous clock signal C4i, and a framing pulse F0i. DATA INPUT/OUTPUT ➃ COMMAND/ADDRESS ➀ D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7 SCLK ➁ ➃ CS ➂ ➂ ➀ ➁ Delays due to MCS-51 internal timing which are transparent. ➂ The falling edge of CS indicates that a COMMAND/ADDRESS byte will be transmitted from the microprocessor. The subsequent byte is always data followed by CS returning high. ➃ A new COMMAND/ADDRESS byte may be loaded only by CS cycling high then low again. D7 The COMMAND/ADDRESS byte contains: 1 bit - Read/Write 0 A5 A4 6 bits - Addressing Data 1 bit - Not used, write logic "0" ➄ The HPhone-II: -latches received data on the falling edge of SCLK -outputs transmit data on the falling edge of SCLK Figure 6 - Serial Port Relative Timing 7-18 D0 A3 A2 A1 A0 R/W MT9092 The data streams operate at 2048kb/s and are Time Division Multiplexed into 32 identical channels of 64kb/s bandwidth. Frame Pulse (a 244nSec low going pulse) is used to parse the continuous serial data streams into the 32 channel TDM frames. Each frame has a 125µSecond period translating into an 8 kHz frame rate. Valid frame pulse occurs when F0i is logic low coincident with a falling edge of C4i. C4i has a frequency (4096MHz) which is twice the data rate. This clock is used to sample the data at the 3/4 bit-cell position on DSTi and to make data available on DSTo at the start of the bit-cell. C4i is also used to clock the HPhone-II internal functions (i.e., DSP, Filter/CODEC, HDLC) and to provide the channel timing requirements. The HPhone-II uses only the first 4 channels of the 32 channel frame. These channels are always defined, beginning with the first channel after frame pulse, as shown in Figure 7 (DSTi and DSTo channel assignments). Channels are enabled independantly by the four control bits Ch0En -Ch 3En residing in the Timing Control Register (address15h). Ch0EN - D-Channel Channel 0 conveys the D-Channel HDLC information. Since this function is dedicated to 16kb/s operation, only the first two bits (LSB's) of the octet are required; the remaining six bits of the D-Channel octet carry no information and are tri-stated. When CH 0EN is high, HDLC data is transmitted on DSTo. When low, DSTo is forced to logic 0 for the two least significant bit positions. Incoming DSTi data is always routed to the HDLC block regardless of this control bit's logic state. Ch1EN - C-Channel Channel 1 conveys the control/status information for Mitel’s layer 1 transceiver. The full 64kb/s bandwidth is available and is assigned according to which transceiver is being used. Consult the data sheet for the selected transceiver for its bit definitions and order of bit transfer. When this bit is high register data is transmitted on DSTo. When low, this timeslot is tri-stated on DSTo. Receive CChannel data (DSTi) is always routed to the register regardless of this control bit's logic state. C-channel data is transferred on the STBUS MSB first by the HPhone-II. Ch2EN and Ch3EN - B1-Channel and B2-Channel Channels 2 and 3 are the B1 and B2 channels, respectively. These bits (Ch 2EN and Ch3EN) are used to enable the PCM channels from/to the HPhone-II as required. Transmit PCM on DSTo When high, PCM from the Filter/CODEC and DSP is transmitted on DSTo in the selected ST-BUS channel. When low, DSTo is forced to logic 0 for the corresponding timeslot. If both Ch 2EN and Ch3EN are enabled, default is to channel 2. Receive PCM from DSTi When high, PCM from DSTi is routed to the DSP and Filter/CODEC in the associated channel. If both Ch2EN and Ch 3EN are enabled the default is to channel 2. 125 µs F0i DSTi, DSTo CHANNEL 0 D-channel LSB first for DChannel CHANNEL 1 C-channel CHANNEL 2 B1-channel CHANNEL 3 B2-channel CHANNELS 4 - 31 Not Used MSB first for C, B1 - & B2Channels Figure 7 - ST-BUS Channel Assignment 7-19 MT9092 New Call Tone Watchdog The New Call Tone Generator produces a frequency shifted square-wave used to toggle the speaker driver outputs. This is intended for use where a ringing signal is required concurrently with an already established voice conversation in the handset. To maintain program integrity an on-chip watchdog timer is provided for connection to the microcontroller reset pin. The watchdog output WD (pin 17) goes high while the HPhone-II is held in reset via the PWRST (pin 6). Release of PWRST will cause WD to return low immediately and will also start the watchdog timer. The watchdog timer is clocked on the falling edge of F0i and requires only this input, along with V DD, for operation. Programming of the DSP for New Call generator is exactly as is done for the tone ringer micro-program except that the OPT bit (DSP Control Register, address 1Eh) is set high. In this mode the DSP does not produce a frequency shifted squarewave output to the filter CODEC section. Instead the DSP uses the contents of the tone coefficient registers, along with the tone warble rate register, to produce a gated squarewave control signal output which toggles between the programmed frequencies. This control signal is routed to the New Call Tone block when the NCT EN control bit is set (General Control Register, address 0Fh). NCT EN also enables a separate gain control block, for controlling the loudness of the generated ringing signal. With the gain control block set to 0dB the output is at maximum or 6 volts p-p. Attenuation of the applied signal, in three steps of 8 dB, provide the four settings for New Call tone (0, -8, -16, -24 dB). The NCT gain bits (NCTG 0-NCTG1) reside in the FCODEC Gain Control Register 2 (address 0Bh). If the watchdog reset word is written to the watchdog register (address 11h) after PWRST is released, but before the timeout period (T=512mSec) expires, a reset of the timer results and WD will remain low. Thereafter, if the reset word is loaded correctly at intervals less than 'T' then WD will continue low. The first break from this routine, in which the watchdog register is not written to within the correct interval or it is written to with incorrect data, will result in a high going WD output after the current interval 'T' expires. WD will then toggle at this rate until the watchdog register is again written to correctly. 5-BIT WATCHDOG RESET WORD X X X W4 W3 W2 W1 W0 0 1 0 1 0 x=don’t care Test Loops Detail LBio and LBoi Loopback Register (address 16h) 7-20 LBio Setting this bit causes data on DSTi to be looped back to DSTo directly at the pins. The appropriate channel enables Ch 0EN -Ch3EN must also be set. LBoi Setting this bit causes data on DSTo to be looped back to DSTi directly at the pins. MT9092 HPhone-II Register Map Address (Hex) WRITE READ 00 HDLC ADDRESS RECOGNITION REGISTER 1 VERIFY 01 HDLC ADDRESS RECOGNITION REGISTER 2 VERIFY 02 HDLC TRANSMIT FIFO HDLC RECEIVE FIFO 03 HDLC CONTROL REGISTER 1 VERIFY 04 NOT USED HDLC STATUS REGISTER 05 HDLC CONTROL REGISTER 2 VERIFY 06 HDLC INTERRUPT ENABLE REGISTER VERIFY 07 NOT USED HDLC INTERRUPT STATUS REGISTER 08 RESERVED RESERVED 09 RESERVED RESERVED 0A FCODEC GAIN CONTROL REGISTER 1 VERIFY 0B FCODEC GAIN CONTROL REGISTER 2 VERIFY 0C RESERVED RESERVED 0D RESERVED RESERVED 0E TRANSDUCER CONTROL REGISTER VERIFY 0F GENERAL CONTROL REGISTER VERIFY 10 RESERVED RESERVED 11 WATCHDOG REGISTER NOT USED 12 LCD SEGMENT ENABLE REGISTER 1 VERIFY 13 LCD SEGMENT ENABLE REGISTER 2 VERIFY 14 C-CHANNEL REGISTER (to DSTo) C-CHANNEL REGISTER (from DSTi) 15 TIMING CONTROL REGISTER VERIFY 16 LOOP-BACK REGISTER VERIFY 17-1C RESERVED RESERVED 1D RECEIVE GAIN CONTROL REGISTER VERIFY 1E DSP CONTROL REGISTER VERIFY 1F RESERVED RESERVED 20 TRANSMIT AUDIO GAIN REGISTER VERIFY 21 TRANSMIT DTMF GAIN REGISTER VERIFY 22 RESERVED RESERVED 23 TONE COEFFICIENT REGISTER 1 VERIFY 24 TONE COEFFICIENT REGISTER 2 VERIFY 25 RESERVED RESERVED 26 TONE RINGER WARBLE RATE REGISTER VERIFY 27-3F RESERVED RESERVED 7-21 MT9092 Register Summary reference to review each of the control/status bit definitions without the need to locate them in the text of the functional block descriptions. This section contains a complete listing of the HPhone-II register addresses, the control/status bit mapping associated with each register and a definition of the function of each control/status bit. The Register Summary may be used for future HDLC Address Recognition Register 1 Adr16 Adr15 Adr14 7 6 5 ADDRESS = 00h WRITE/READ VERIFY Adr13 Adr12 Adr11 Adr10 4 3 2 1 A1EN Power Reset Value 0000 0000 0 Adr 16-11 A six bit mask used to interrogate the first byte of the received address. Adr16 is MSB. In the Q.921 specification these bits are defined to be Sapi5-0. Adr 10 This bit is used in address comparison if a seven bit address is being checked for (Control bit Seven of Control Register 2 is set). In the Q.921 specification this bit is defined to be C/R (Command/Response). A1EN When this bit is high, this six (or seven) bit mask is used in address comparison of the first address byte. If address recognition is enabled, any packet failing the address comparison will not be stored in the RX FIFO. A1EN must be high for All-call (1111111) address recognition for single byte address. When this bit is low, this bit mask is ignored in address comparison. HDLC Address Recognition Register 2 Adr26 Adr25 Adr24 7 6 5 ADDRESS = 01h WRITE/READ VERIFY Adr23 Adr22 Adr21 Adr20 4 3 2 1 A2EN Power Reset Value 0000 0000 0 Adr 26-20 A seven bit mask used to interrogate the second byte of the received address. Adr26 is MSB. This mask is ignored (as well as first byte mask) if an All call address (1111111) is received. In the Q.921 specification these bits are defined to be Tei6-0. A2EN When this bit is high this seven bit mask is used in address comparison of the second address byte. If address recognition is enabled, any packet failing the address comparison will not be stored in the RX FIFO. A2EN must be high for All-call address recognition. When this bit is low, this bit mask is ignored in address comparison. HDLC Transmit/Receive FIFO Register ADDRESS = 02h WRITE/READ D7 D6 D5 D4 D3 D2 D1 D0 7 6 5 4 3 2 1 0 Power Reset Value Not Applicable The Transmitter FIFO is 19 words deep. Each word consists of 8 bits of data from the internal data bus and 2 status bits from CONTROL Register 1 (EOP and FA). If there is data in the Tx FIFO then the lowest data byte in it is loaded into an output shift register for transmission, and the remaining data shifts down by one word position (Tx FIFO read). A write to a full Tx FIFO will update the top byte only. The receiver FIFO is 19 words deep. During a receiver write, the last 8 bits of a shift register buffer and two status bits are loaded into 7-22 MT9092 HDLC Control Register 1 ADDRESS = 03h WRITE/READ VERIFY Adrec HRxEN HTxEN 7 Adrec HRxEN 6 5 EOP FA Mark Idle Trans - 4 3 2 1 0 Power Reset Value 0000 0000 When high this bit will enable address recognition. This forces the receiver to recognize only those packets having the unique address as programmed in the Receive Address Recognition Registers or if the address is an All-Call address. When low, all packets are recognized. When low this bit will disable the HDLC receiver. The receiver will disable after the rest of the packet presently being received is finished. When high the receiver will be immediately enabled (depending on the state of CHoEN) and will begin searching for flags, Go-aheads etc. HTxEN When low this bit will disable the HDLC transmitter. The transmitter will disable after the completion of the packet presently being transmitted. When high the transmitter will be immediately enabled (depending on the state of CHoEN) and will begin transmitting data, if any, or go to a Mark idle or Interframe time fill state. EOP Forms a tag on the next byte written to the Tx FIFO and when set will indicate an EOP byte to the transmitter which will transmit an FCS following this byte. This facilitates loading of multiple packets into Tx FIFO. This bit is reset automatically after a write to the Tx FIFO occurs. Forms a tag on the next byte written to Tx FIFO and when set will indicate to the transmitter that it should abort the packet in which that byte is being transmitted. This bit is reset automatically after a write to the Tx FIFO. When low, the transmitter will be in an idle state. When high it is in an Interframe time fill state. These two states will only occur when the Tx FIFO is empty. When high this bit will enable transparent mode. The HDLC will perform the serial-to-parallel and parallel-to-serial conversion without inserting or deleting zeros. No CRC bytes are sent or monitored nor are flags, aborts or Go-aheads. No address recognition is monitored. The receiver or transmitter must be enabled through Control Register 1 as well as setting CH0EN. FA Mark Idle Trans HDLC Status Register Idle Intgen Chan 7 Intgen Idle Chan RxBS2, RxBS1 Note Txstat2, Txstat1 Txstat Rxstat Rxstat RxBS2 RxBS1 Txstat 2 1 2 1 6 5 4 3 2 1 Power Reset Value 00XX 1000 0 Is set to a 1 when an interrupt (in conjunction with the Interrupt Mask Register) has been generated by the HDLC. This is an asynchronous event. It is reset when the Interrupt Register is read. Is set to a 1 when an Idle Channel state (15 or more ones) has been detected by the receiver. This is an asynchronous event. Status becomes valid after first 15 bits or the first zero bit received. Indicates the status of the next byte to be read from the Rx FIFO. RxBS2 RxBS1 Byte status 1 1 last byte (bad packet) 0 1 first byte 1 0 last byte (good packet) 0 0 packet byte - If two consecutive first byte signals are received without an intervening last byte, then an overflow has occurred and the first packet (or packets) are bad. A bad packet indicates that either a frame abort has occurred or the FCS did not match. - On power-up these bits are in an indeterminate state until the first byte is written to Rx FIFO. These two bits are encoded to indicate the present state of Tx FIFO. This is an asynchronous event. Txstat1 Tx FIFO Status Txstat2 0 0 TxFULL 0 1 5 OR MORE BYTES (15 if Fltx set) 1 1 4 OR LESS BYTES (14 if Fltx set) 1 Rxstat2, Rxstat1 ADDRESS = 04h READ 0 TxEMPTY These two bits are encoded to indicate the present state of Rx FIFO. This is an asynchronous event. Rxstat1 Rx FIFO Status Rxstat2 0 0 RxEMPTY 0 1 14 OR LESS BYTES (4 if Flrx set) 1 1 1 0 15 OR MORE BYTES (5 if Flrx set) RxOVERFLOW EXISTS Note: Bits marked "-" are reserved bits and should be written with logic "0". 7-23 MT9092 HDLC Control Register 2 Intsel 7 Intsel Tcrci Seven Flrx Fltx Rxfrst Txfrst 6 ADDRESS = 05h WRITE/READ VERIFY Tcrci Seven Flrx Fltx Rxfrst Txfrst 5 4 3 2 1 0 Power Reset Value 0000 0000 When high, this bit will cause bit 2 of the Interrupt Register to reflect a Transmit FIFO underrun (Txunder). When low, this interrupt will reflect a frame abort (FA). When high, this bit will inhibit transmission of the CRC. That is, the transmitter will not insert the computed CRC onto the bit stream after seeing the EOP tag byte. The microprocessor then has the opportunity to insert the CRC as part of the data field. When high, this bit will enable seven bits of address recognition in the first address byte. The received address byte must have bit 0 equal to 1 which indicates a single address byte is being received. When high, this bit will change the Rx FIFO interrupt and status level from 15 to 5 bytes, thus allowing the microprocessor more time to react to interrupt conditions. When high, this bit will change the Tx FIFO interrupt and status level from 4 to14 bytes, thus allowing the microprocessor more time to react to interrupt conditions. When high, the Rx FIFO will be reset. This causes the receiver to be disabled until the next reception of a flag, an occurrence which resets this bit. The Status Register will identify the FIFO as being empty. However, the actual bit values of data in the Rx FIFO will not be reset. When high, the Tx FIFO will be reset. The Status Register will identify the FIFO as being empty. This bit will be reset when data is written to the Tx FIFO. The actual bit values of data in the Tx FIFO will not be reset.. HDLC Interrupt Enable Register GA 7 ADDRESS = 06h WRITE/READ VERIFY EOPD TEOP EOPR TxFL 6 5 4 3 FA/Tx Under RxFf Rx Ovfl 2 1 0 Power Reset Value 0000 0000 This register is used with the Interrupt Register to mask out the interrupts that are not required by the microprocessor. Interrupts that are masked out will not produce an IRQ; however, they will set the appropriate bit in the Interrupt Register. An interrupt is disabled when the microprocessor writes a 0 to a bit in this register. This register is cleared on power reset. Note: Bits marked "-" are reserved bits and should be written with logic "0". 7-24 MT9092 HDLC Interrupt Status Register GA 7 ADDRESS = 07h READ EOPD TEOP EOPR 6 5 4 FA/Tx TxFL Under 3 2 RxFf Rx Ovfl 1 0 Power Reset Value 0000 0000 This register indicates the source of an interrupt. It is used in conjunction with the Interrupt Enable Register to generate an interrupt. The register is reset by the microprocessor read, which also resets the IRQ output. All interrupts are generated by a transition. That is, the register informs the user that an interrupt did occur but may not presently be valid. To determine if the interrupt is presently valid the Status Register should be polled. Due to the asynchronous nature of the interrupts, an interrupt occurring during a read of this register will be saved until the read is over, unless it is an interrupt that has already been set. GA EOPD Indicates a go-ahead pattern (011111110) was detected by the HDLC receiver. This bit is set when an end of a packet (EOP) byte is written into the RX FIFO by the HDLC receiver. This can be in the form of a flag, an abort sequence, or an invalid packet. TEOP This bit is set when the transmitter has finished sending the closing flag of a packet or after a packet has been aborted . EOPR This bit is set when the byte about to be read from the Rx FIFO is the last byte of the packet. It is also set if the Rx FIFO is read and there is no data in it. TxFL Tx FIFO low indication. Indicates that a transition from 5 to 4 bytes in the Tx FIFO was detected. If Fltx is set then this will be 15 to 14 bytes. FA:TxUnder When Intsel bit of Control Register 2 is low this bit (FA) is set when a frame abort is received during packet reception. It must be received after a minimum number of bits have been received (26) otherwise it is ignored (see HDLC FRAME STRUCTURE). When Intsel is high this bit is set for a Tx FIFO underrun indication. Indicates that a read by the transmitter was attempted on an empty Tx FIFO without an EOP or FA tagged byte. RxFf RxOvfl Indicates that a transition from 14 to 15 bytes in the FIFO was detected. If Flrx is set then this will be 4 to 5 bytes. Indicates that the Rx FIFO overflowed (i.e. an attempt to write to a full RX FIFO). The HDLC will always disable the receiver once the receive overflow has been detected. The receiver will be re-enabled upon detection of the next flag, but ADDRESS = 08h and 09h are RESERVED FCODEC Gain Control Register 1 7 Receive Gain Setting (dB) ADDRESS = 0Ah WRITE/READ VERIFY RxFG2 RxFG1 RxFG0 6 5 4 3 RxFG2 RxFG 1 RxFG0 Power Reset Value X000 X000 TxFG2 TxFG1 TxFG0 2 1 0 Transmit Gain Setting (dB) TxFG 2 TxFG 1 TxFG 0 0 0 0 (default) 0 0 0 0 -1 0 0 1 1 0 0 1 -2 0 1 0 2 0 1 0 -3 0 1 1 3 0 1 1 -4 1 0 0 4 1 0 0 -5 1 0 1 5 1 0 1 -6 1 1 0 6 1 1 0 -7 1 1 1 7 1 1 1 (default) 0 RxFGn = Receive Filter Gain n TxFGn = Transmit Filter Gain n Note: Bits marked "-" are reserved bits and should be written with logic "0". 7-25 MT9092 FCODEC Gain Control Register 2 - NCTG1 NCTG0 - 7 ADDRESS = 0Bh WRITE/READ VERIFY 6 5 4 - STG2 3 2 Power Reset Value 0X00 X000 STG1 STG0 1 0 Side-tone Gain STG 2 STG 1 STG 0 (default) OFF 0 0 0 -9.96 0 0 1 0 -6.64 0 1 0 1 -3.32 0 1 1 0 1 0 0 3.32 1 0 1 6.64 1 1 0 9.96 1 1 1 Gain (dB) NCTG 1 NCTG0 0 (default) 0 0 -8 0 1 -16 1 -24 1 Setting (dB) NCTGn = New Call Tone Gain n STGn = Side-tone Gain n ADDRESSES 0Ch and 0Dh are RESERVED Transducer Control Register PuFC Tfhp 7 6 PuFC DIAL EN 5 ADDRESS = 0Eh WRITE/READ VERIFY SIDE EN 4 MIC EN 3 MIC/ HNSTMIC 2 SPKR HSSPKR EN EN 1 0 Power Reset Value 0000 0000 SPKR EN When high, the Filter/CODEC is powered up. When low, the Filter/CODEC is powered down. If PuFC, SPKR EN and HSSPKR EN are all low then the VRef/VBias circuit is also powered down. When high, an additional high pass function (passband beginning at 400Hz) is inserted into the transmit path. When low, this highpass filter is disabled. When high, a first order lowpass filter is inserted into the receive path (3dB = 1kHz). When low, this lowpass filter is disabled. When high, the sidetone path is enabled (assuming STG2-0 are not all low). When low, the sidetone path is disabled. When high, the selected transmit microphone is enabled to the transmit filter section. When low, the microphone path is muted. When high, the handsfree microphone (pins MIC±) is muxed into the transmit path. When low, the handset microphone (pins M±) is muxed into the transmit path. Both are contingent on 'MIC EN". When high, the handsfree loudspeaker driver is powered up. When low, this driver is powered down. HSSPKR EN When high, the handset speaker driver is powered up. When low, this driver is powered down. Tfhp DIAL EN SIDE EN MIC EN MIC/HNSTMIC Note: Bits marked "-" are reserved bits and should be written with logic "0". 7-26 MT9092 General Control Register RST 7 DATA SEL ADDRESS = 0Fh WRITE/READ VERIFY A/µ 6 Sign-Mag/ CCITT 5 4 Rx A/µ MIC A/µ 3 2 Side A/µ NCT EN 1 0 Power Reset Value 0000 0000 RST Active high reset. Performs the same function as PWRST but does not affect the microport or the watchdog circuits. To remove this reset a PWRST must occur or this bit must be written low. DATASEL When high, the microport transmit and receive are performed on separate pins. DATA1 is receive while DATA2 is transmit. When low, the microport conforms to Intel MCS-51 mode 0 specifications; DATA1 is a bi-directional (transmit/receive) serial data pin while DATA2 is internally disconnected and tri-stated. When high, A-Law (de)coding is selected. When low, µ-Law (de)coding is selected. A/µ Sign-mag/CCITT When high, sign-magnitude bit coding is selected, When low, true CCITT PCM coding is selected. When high, the receiver driver nominal gain is set at -9.7 dB. When low this driver nominal gain is set at -12.3 dB. RxA/µ When high, the transmit amplifier nominal gain is set at 15.4 dB. When low this amplifier nominal gain is set at 6.1 MICA/µ dB. SIDEA/µ When high, the side-tone nominal gain is set at -18.8 dB. When low this nominal gain is set at -11 dB. NCT EN When high, the new call tone generator output from the DSP is selected as the source for the loudspeaker path. When low, the CODEC output is selected for the loudspeaker path. Note that SPKR EN must also be set high for new call tone to function. ADDRESS 10h is RESERVED Watchdog Register 7 ADDRESS = 11h WRITE - - 6 5 W4 W3 W2 W1 W0 4 3 2 1 0 Power Reset Value XXX0 1010 WATCHDOG RESET WORD - XXX01010 LCD Segment Enable Register 1 ADDRESS = 12h WRITE/READ VERIFY SC8 SC7 SC6 SC5 SC4 SC3 SC 2 SC1 7 6 5 4 3 2 1 0 Power Reset Value 0000 0000 Twelve segment control bits used for the LCD outputs. When high the respective segment is on. When low the respective segment is off. LCD Segment Enable Register 2 ADDRESS = 13h WRITE/READ VERIFY - - - - SC12 SC11 SC10 SC9 7 6 5 4 3 2 1 0 Power Reset Value XXXX 0000 Twelve segment control bits used for the LCD outputs. When high the respective segment is on. When low the respective segment is off. Note: Bits marked "-" are reserved bits and should be written with logic "0". 7-27 MT9092 C-Channel Register ADDRESS = 14h WRITE/READ D7 D6 D5 D4 D3 D2 D1 D0 7 6 5 4 3 2 1 0 Power Reset Value Write = 1111 1111 Read = Not Applicable Micro-port access to the ST-BUS C-Channel information. Timing Control Register ADDRESS = 15h WRITE/READ VERIFY - - - - 7 6 5 4 CH3EN CH2EN CH1EN CH0EN 3 2 1 Power Reset Value XX0X 0000 0 All bits active high: Ch2EN and Ch3EN Channels 2 and 3 are the B1 and B2 channels, respectively. PCM associated with the DSP, Filter/CODEC and transducer audio paths is conveyed in one of these channels as selected in the timing control register. Transmit B1 and B2 data on DSTo When high PCM from the Filter/CODEC and DSP is transmitted on DSTo in the associated channel. When low DSTo is forced to logic 0 for the corresponding timeslot. If both Ch2EN and Ch3EN are enabled, data defaults to channel 2. Receive B1 and B2 data on DSTi When enabled PCM from DSTi is routed to the DSP and Filter/CODEC in the associated channel. If both Ch2EN and Ch3EN are enabled, data input defaults to channel 2. Ch1EN Channel 1 conveys the control/status information for the layer 1 transceiver. The full 64kb/s bandwidth is available and is assigned according to which transceiver is being used. Consult the data sheets for the transceiver selected. When high register data is transmitted on DSTo. When low this timeslot is tri-stated on DSTo. Receive C-Channel data (DSTi) is always routed to the register regardless of this control bit's logic state. Ch0EN Channel 0 conveys the D-Channel HDLC information. Since this function is dedicated to 16kb/s operation, only the first Loop-back Register 7 ADDRESS = 16h WRITE/READ VERIFY LBio LBoi - - - - - 6 5 4 3 2 1 0 Power Reset Value X00X XXXX LBio Active high enables data from the ST-BUS input to be looped back to the ST-BUS output directly at the pins. The DSTo tri- LBoi Active high enables data from ST-BUS output to be looped back to the ST-BUS input directly at the pins. state driver must also be enabled using one of the channel enable signals. ADDRESS 17h-1Ch are RESERVED Note: Bits marked "-" are reserved bits and should be written with logic "0". 7-28 MT9092 Receive Gain Control Register ADDRESS = 1Dh WRITE/READ VERIFY - AUTO B5 B4 B3 B2 B1 B0 7 6 5 4 3 2 1 0 Power Reset Value 0000 0000 AUTO When high autonulling of the transmit PCM is enabled. When low, autonulling is disabled. This bit is used in conjunction with B5-B0 These 6 bits (indicated below in hexadecimal) are decoded to control Rx pcm gain: the PS2 - PS0 bits of the DSP Control Register at address 1Eh. B5-B0 Gain Setting (dB) B5-B0 Gain Setting (dB) 3F 3E 3D 3C 3B 3A 39 38 37 36 35 34 33 32 31 30 2F 2E 2D 2C 2B 2A 29 28 27 26 25 24 23 22 21 20 +22.5 +21.0 +19.5 +18.0 +16.5 +15.0 +13.5 +12.0 +10.5 +9.0 +7.5 +6.0 +4.5 +3.0 +1.5 +0.0 -1.5 -3.0 -4.5 -6.0 -7.5 -9.0 -10.5 -12.0 -13.5 -15.0 -16.5 -18.0 -19.5 -21.0 -22.5 -24.0 1F 1E 1D 1C 1B 1A 19 18 17 16 15 14 13 12 11 10 0F 0E 0D 0C 0B 0A 09 08 07 06 05 04 03 02 01 00 -25.5 -27.0 -28.5 -30.0 -31.5 -33.0 -34.5 -36.0 -37.5 -39.0 -40.5 -42.0 -43.5 -45.0 -46.5 -48.0 -49.5 -51.0 -52.5 -54.0 -55.5 -57.0 -58.5 -60.0 -61.5 -63.0 -64.5 -66.0 -67.5 -69.0 -70.5 -72.0 Note: B0-B5 of addresses 20h and 21h are encoded in the same manner Note: Bits marked "-" are reserved bits and should be written with logic "0". 7-29 MT9092 DSP Control Register ADDRESS = 1Eh WRITE/READ VERIFY PS2 PS1 7 6 OPT: RxMUTE: TxMUTE: DRESET: PS0 5 OPT RxMUTE TxMUTE - DRESET 4 3 2 1 0 Power Reset Value 0000 0000 When high, the tone ringer is in New Call tone mode. When low the normal tone ringer program is executed. This bit when high turns off the receive PCM channel, substituting quiet code. This bit when high turns off the transmit PCM channel, substituting quiet code. This bit (when high) enables the DSP. If low, no programs are executed, the master clock is disabled and the program counter is reset to zero. These bits are program select bits for the DSP Rom programs. PS2-PS0: PS2 PS1 PS0 0 0 0 Power up reset program 0 0 1 Gain control program 0 1 0 DTMF & Gain control program 0 1 1 Tone Ringer & Gain control program 1 0 0 Handsfree program 1 0 1 Reserved 1 1 0 Reserved 1 1 1 Reserved MICRO-PROGRAM Transmit Audio Gain Register - 7 6 ADDRESS = 20h WRITE/READ VERIFY B5 B4 B3 B2 B1 B0 5 4 3 2 1 0 Power Reset Value XX11 0000 This register controls the transmit speech path gain in 1.5dB steps as in Receive Gain Register (address 1Dh). ADDRESS = 21h WRITE/READ VERIFY Transmit DTMF Gain Register - 7 6 B5 B4 B3 B2 B1 B0 5 4 3 2 1 0 Power Reset Value XX10 1110 This register controls the transmit DTMF level in 1.5dB steps as in Receive Gain Register (address 1Dh). ADDRESS 22h is RESERVED Note: Bits marked "-" are reserved bits and should be written with logic "0". 7-30 MT9092 Tone Coeff Register 1-DTMF or Tone Ringer ADDRESS = 23h WRITE/READ VERIFY B7 B6 B5 B4 B3 B2 B1 B0 7 6 5 4 3 2 1 0 Power Reset Value 0000 0000 This register is used to program the low-group frequency of the DTMF program. The tone coefficient is calculated as follows: COEF = 0.128 x Frequency where: Frequency is in Hz (note: COEF must be converted to an 8 bit binary integer) Highest frequency possible: 1992.2 Hz Lowest frequency possible: 7.8 Hz Frequency resolution: 7.8 Hz Pre-twist: -2.1dB ± 0.2dB This register is used to program the first frequency of the squarewave ringer program. The tone coefficient is calculated as follows: COEF = 8000 / Frequency where: Frequency is in Hz (note: COEF must be rounded off and converted to an 8 bit binary integer) Highest frequency possible: 4000 Hz Lowest frequency possible: 31.4 Hz Frequency resolution: non-linear Tone Coeff Register 2-DTMF or Tone Ringer ADDRESS = 24h WRITE/READ VERIFY B7 B6 B5 B4 B3 B2 B1 B0 7 6 5 4 3 2 1 0 Power Reset Value 0000 0000 This register is used to program the high-group frequency of the DTMF program. The tone coefficient is calculated as follows: COEF = 0.128 x Frequency where: Frequency is in Hz (note: COEF must be converted to an 8 bit binary integer) Highest frequency possible: 1992.2 Hz Lowest frequency possible: 7.8 Hz Frequency resolution: 7.8 Hz Pre-twist: 0dB This register is used to program the second frequency of the squarewave program. The tone coefficient is calculated similarly to tone ADDRESS 25h is RESERVED Tone Ringer Warble Rate-Tone Ringer ADDRESS = 26h WRITE/READ VERIFY B7 B6 B5 B4 B3 B2 B1 B0 7 6 5 4 3 2 1 0 Power Reset Value 0000 0000 The tone ringer will switch between squarewave frequencies at a warble frequency defined by this register. The relationship between the duration period of each tone and the 8 bit warble coefficient is as follows: Tone duration (warble frequency) = 500 / COEF where: Frequency is in Hz, and 0≤COEF <256 Highest frequency possible: 500 Hz Lowest frequency possible: 2.0 Hz Addresses: 27h to 2Dh are transmit and receive gains and coefficients used by the filters in the handsfree decision circuit. 2Eh to 3Fh are scratch-pad ram locations used by the DSP algorithms as temporary storage during calculations. 7-31 MT9092 Applications To maintain a fully differential topology in the transmit path the suggested connection scheme for the transmit microphones is shown in Figure 8. However, it is possible to use a single-ended arrangement as shown in Figure 9 for the transmit interface. In this case the dynamic range of the MT9092 is reduced by half. In both figures the output drivers are connected in a fully differential manner. transmisssion devices which connect directly with the MT9092 to complete an application; the MT8930 (SNIC) and the MT8971/72 (DSIC/DNIC). An ISDN 4-wire "TE" function is implemented with the MT8930/MT9092 combination. A 2-wire digital phone for PABX, key-systems and other proprietary applications is implemented with the MT8971/72/ MT9092 combination. Figures 10 and 11 show the 4-wire and 2-wire applications, respectively. The MT9092 is a member of the Mitel family of digital terminal equipment components. There are two 330Ω +5V + + - Av = 1+ 0.1µF 100K R 2R T + VBias T R 100K 10µF 511Ω 0.1µF - Electret Microphone 330Ω 511Ω +5V + + 100K R 2R Av = 1+ T 0.1µF T R 0.1µF 100K 6 DSTi DSTo 5 4 3 2 1 44 + Electret Microphone 0.1µF 511Ω 43 42 41 40 7 39 8 38 9 37 10 36 11 35 IRQ SCLK DATA2 DATA1 CS WD + 40Ω nom. 32Ω min. C4i F0i 12 75Ω 150Ω MT9092 +5V 75Ω 34 13 33 14 32 15 31 16 30 17 29 18 19 20 21 22 23 24 25 26 27 28 .1µF 1000pF 1000pF LCD 1000pF caps are optional Note: Single-ended configurations reduce dynamic range by a factor of two. LCD Figure 8 - Application Circuit - fully differential audio input 7-32 10µF 511Ω - +5V Serial Microport INTEL MCS-51 0.1µF VBias + VBias ST-BUS Port to Transmission Device + - MT9092 + +5V VBias – 330Ω + T 1µF R 10µF 1K + Electret Microphone 330Ω VBias + – +5V + T 10µF 1K 1µF R + Electret Microphone 0.1µF 0.1µF VBias +5V 6 ST-BUS Port to Transmission Device 4 3 2 1 44 43 42 41 40 DSTi 7 39 DSTo 8 38 9 37 10 36 11 35 C4i F0i MT9092 40Ω nom. 32Ω min. 75Ω +5V 75Ω 34 SCLK 13 33 14 32 DATA2 + 150Ω IRQ 12 Serial Microport INTEL MCS-51 5 DATA1 15 31 CS 16 30 WD 17 29 .1µF 1000pF 1000pF 1000pF caps are optional LCD Note: Single-ended configurations reduce dynamic range by a factor of two. 18 19 20 21 22 23 24 25 26 27 28 LCD Figure 9 - Application Circuit - single-ended audio input 7-33 MT9092 LTx HSPKR+ C4b C4i F0b F0i HSPKR- CCITT ISDN Reference Point S Interface 5 Volts VBias DC to DC Converter MT8930 SNIC with HDLC Controller DSTo DSTi DSTi DSTo AD0-7 MT9092 HPhone-∏ M+ Digital Telephone with HDLC Controller M- Handset MIC+AAAAA AAAAA MIC- AAAA AAAAAA Microphone AAAAA SPKR+ LRx IRQ (ALE) (RD) SPKR- IRQ CS (WR) SCLK AS (ALE) Speaker DATA1 E (RD) R/W (WR) AD0-7 8051 INTEL IRQ MCS51 Figure 10 - CCITT ISDN Voice/Data Terminal Equipment - TE1 5 volts DC to DC CONVERTER C4i F0 F0i HSPKR+ HSPKR- MT8972 Lin DNIC ZT Twisted Pair to Central PBX C4 Lout DSTo DSTi DSTi DSTo MT9092 HPhone-∏ Digital Telephone with HDLC Controller M+ Handset MMIC+ AAAAA AAAA AAAAAAA Microphone MIC- AAAA AAAAA SPKR+ SPKR10.24 MHz IRQ SCLK CS DATA1 INTEL MCS-51 Figure 11 - Voice/Data Digital Telephone Set Circuit 7-34 Speaker MT9092 Programming Examples that these steps are from the power-up reset default definition. If some other state is currently true then some programming steps may be omitted while new ones may be required. Some examples of the programming steps required to set-up various telephony functions are given. Note Standard Full-duplex handset call Description select B-Channel of operation Address 15h DATA bits 2 or 3 (as required) reset DSP set Rx gain (ie 0dB with Tx set Tx gain (ie 0dB) start Rx gain program 1Eh 1Dh 20h 1Eh 00h 70h (or as required) 30h (or as required) 21h select transducers and turn on sidetone and filter/CODEC 0Eh 99h set sidetone gain 0Bh 04h (for 0dB or as required) optional: set CODEC Rx and Tx gain select A-Law versus µ-Law 0Ah 0Fh as required (0dB default) bits 1-5 (as required) Description select B-Channel of operation Address 15h DATA bits 2 or 3 (as required) reset DSP set Rx gain (ie 12 dB) set Tx gain (ie 0dB) start handsfree program 1Eh 1Dh 20h 1Eh 00h 38h (or as required) 30 h (or as required) 81h select transducers and filter/CODEC and turn off sidetone 0Eh 1Eh 0Ah 0Fh as required (0dB default) bits 1-5 (as required) Description select B-Channel of operation Address 15h DATA bits 2 or 3 (as required) reset DSP set Rx gain (ie 0 dB with Tx autonull) set Tx gain (ie 0dB) write tone coefficient 1 write tone coefficient 2 write warble tone rate coefficient start tone ringer program 1Eh 1Dh 00h 70h (or as required) 20h 23h 24h 26h 1Eh 30h (or as required) as required as required as required 61h select speaker and filter/CODEC and turn off sidetone 0Eh 82h control ringer cadence by toggling RxMUTE 1Eh 61 69 61 69 autonull) Half-Duplex handsfree operation optional: set CODEC Rx and Tx gain select A-Law versus µ-Law Generate tone ringer (on) (off) (on) (off) etc... 7-35 MT9092 Generate DTMF tones Description select B-Channel of operation Address 15h DATA bits 2 or 3 (as required) reset DSP set Rx DTMF gain (ie -20 dBm0) set Tx audio gain (ie 0dB) set Tx DTMF gain (ie -4dBm0) write tone coefficient 1 write tone coefficient 2 start DTMF program 1Eh 1Dh 20h 21h 23h 24h 1Eh 00h 22h (or as required) 30h (or as required) 2Eh (or as required) as required as required 41h select transducers and filter/CODEC (PuFC) and turn off sidetone 0Eh as required 0Ah as required (0dB default) 1Eh as required optional: set CODEC Rx gain send tones in only Rx or Tx by disabling RxMUTE or TxMUTE appropriately New Call Tone Description Address DATA Assume that a B-Channel of operation has already been selected for the concurrent handset conversation. If this is not true select one. select B-Channel of operation 15h bits 2 or 3 (as required) reset DSP 1Eh 00h ********************************************************************************** set Rx gain (ie 0 dB with Tx autonull) set Tx gain (ie 0dB) 1Dh 20h 70h (or as required) 30h (or as required) Note: these two steps a required for the concurrent conversation only and do not affect new call tone generation. See Standard Full-duplex handset call for required programming. ********************************************************************************** write write write start 23h 24h 26h 1Eh as required as required as required 71h set new call tone gain 0Bh NCTG2-1 (as required) select speaker 0Eh enable new call tone 0Fh 02h 9Bh (assuming a concurrent handset call) 01h (assuming all other bits are µ-Law control ringer cadence by toggling between gain control and tone ringer with gain control programs 1Eh 7-36 tone coefficient 1 tone coefficient 2 warble rate coefficient new call tone ringer program 71h (on) 31h (off) 71h (on) etc... MT9092 Absolute Maximum Ratings Parameter Symbol Min Max Units VDD-VSS -0.3 7 V VI/VO VSS-0.3 VDD+0.3 V ±20 mA +150 °C PD 750 mW ±2.0 KV 1 Supply Voltage 2 Voltage on any I/O pin 3 Current on any I/O pin (transducers excluded) II/IO 4 Storage Temperature TS 5 Power Dissipation (package) 6 Static Discharge ESD 7 Latch-up Current ILU Plastic -65 ±100 mA Recommended Operating Conditions - Voltages are with respect to VSS unless otherwise stated. Characteristics Sym Min Typ Max Units 5 5.25 V Test Conditions 1 Supply Voltage VDD 4.75 2 Input Voltage (high) * VIH 2.4 VDD V Noise margin = 400mV 3 Input Voltage (low) * VIL VSS 0.4 V Noise margin = 400mV 4 Operating Temperature TA -40 +85 °C 5 Clock Frequenecy (C4i) fCLK 4092 4100 kHz 4096 * Excluding PWRST which is a Schmitt Trigger Input. Power Characteristics Characteristics 1 Supply Current (clock enabled, all functions off 2 Supply Current by function Filter/Codec HDLC DSP Handset Driver (bias only, no signal) Speaker Driver (bias only, no signal) Timing Control, C-Channel, ST-BUS, etc. Total all functions enabled Sym Min Typ IDDC1 IDDF1 IDDF2 IDDF3 IDDF4 IDDF5 IDDF6 1.5 1.0 1.5 1.5 1.5 1.0 IDDFT 8.0 Max Units 6 mA mA mA mA mA mA mA 14 mA Test Conditions See Note 1. See Note 1. See Note 2. Note 1: Power delivered to the load is in addition to the bias current requirements. Note 2: I DDFT is not additive to IDDC1 . 7-37 MT9092 DC Electrical Characteristics† (except LCD Drive Pins) - Voltages are with respect to ground (VSS) unless otherwise stated. Characteristics Sym Min 1 Input HIGH Voltage TTL inputs VIN 2.0 2 Input LOW Voltage TTL inputs VIL 3 VBias Voltage Output 4 Input Leakage Current 1 5 Positive Going Threshold Voltage (PWRST only) Negative Going Threshold Voltage (PWRST only) VT+ 6 Output HIGH Current TTL O/P IOH -10 7 Output LOW Current TTL O/P IOL 5 8 Output Voltage 9 Typ‡ Max Units Test Conditions V 0.8 VBias VDD/2 IIZ 0.1 V V Max. Load = 10kΩ µA VIN = VDD to VSS -16 mA VOH = 2.4V DSTo, WD, DATA1, DATA2, IRQ 10 mA VOL = 0.4V DSTo, WD, DATA1, DATA2, IRQ VRef (VDD /2) -1.5 V Output Leakage Current 1 IOZ 0.01 10 Output Capacitance Co 15 pF 11 Input Capacitance Ci 10 pF 3.3 10 1.5 VT- 10 µA No load VOUT = VDD and VSS † DC Electrical Characteristics are over recommended temperature and range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. 1 TTL compatible pins only. DC Electrical Characteristics† - LCD Drive Pins - Voltages are with respect to ground (VSS) unless otherwise stated. Characteristics Sym Min Typ Max Units Test Conditions 1 Output High Voltage Both Segment and Backplane VOH 4.8 --- --- Volts Io = 1mA, VDD = 5V 2 Output Low Voltage Both Segment and Backplane VOL --- --- 0.2 Volts Io = 1mA, VDD = 5V 3 Segment Output Load --- --- 1200 pF 4 Backplane Output Load --- --- 7200 pF 5 Frequency 62 62.5 63 Hz 7-38 MT9092 AC Characteristics† for A/D (Transmit) Path - 0dBm0 = 1.421Vrms for µ-Law and 1.477Vrms for A-Law, at the CODEC. (VRef = 0.5 volts and VBias = 2.5 volts). All parameters pertain exclusively to the Filter/CODEC except absolute half-channel gain and transmit idle channel noise. Characteristics Sym Min Typ‡ Max 5.79 6.0 1 Analog input equivalent to overload decision ALi3.17 ALi3.14 2 Absolute half-channel gain. Transmit filter gain = 0dB setting GAX1 GAX2 5.4 14.7 All other transmit filter settings (1 to 7dB) are in addition to 0dB setting GAX1 GAX2 3 Gain tracking vs. input level CCITT G.714 Method 2 4 6.1 15.4 Units Vp-p Vp-p Test Conditions µ-Law A-Law Both at CODEC 6.8 16.1 dB dB MICA/u=0* MICA/u=1* MIC± or M± to PCM 1020Hz -0.15 -0.15 +0.15 +0.15 dB dB MICA/u=0* MICA/u=1* from nominal MIC± or M± to PCM 1020Hz GTX -0.3 -0.6 -1.6 0.3 0.6 1.6 dB dB dB 3 to -40 dBm0 -40 to -50 dBm0 -50 to -55 dBm0 Signal to total Distortion vs. input level. CCITT G.714 Method 2 DQX 35 29 24 dB dB dB 0 to -30dBm0 -40 dBm0 -45 dBm0 5 Transmit Idle Channel Noise NCX NPX 6 Gain relative to gain at 1020Hz <50 Hz 60 Hz 200 Hz 300-3000 Hz 3000-3400 Hz 4000 Hz >4600 Hz GRX 7 Absolute Delay DAX 360 µs at frequency of minimum delay 8 Group Delay relative to D AX DDX 750 380 130 750 µs µs µs µs 500-600 Hz 600-1000 Hz 1000-2600 Hz 2600 - 2800 Hz 9 Power Supply Rejection f=1020 Hz f=0.3 to 3 kHz f=3 to 4 kHz f=4 to 50 kHz 15 -72 -0.25 -0.9 PSSR PSSR1 PSSR2 PSSR3 37 40 35 40 17.5 -66 dBrnC0 dBrn0p -25 -30 0.0 0.25 0.25 -12.5 -25 dB dB dB dB dB dB dB dB dB dB dB µ-Law A-Law ±1000mVrms peak signal µ-Law PSSR1-3 not production tested † AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. * Note: MICA/u, refer to General Control Register, address 0Fh. 7-39 MT9092 AC Characteristics† for D/A (Receive) Path - 0dBm0 = 1.421Vrms for µ-Law and 1.477Vrms for A-Law, at the CODEC. (VRef = 0.5volts and VBias = 2.5 volts). All parameters pertain exclusively to the Filter/CODEC except absolute gain and receive idle channel noise. Characteristics Sym Min 1 Analog output at the CODEC full scale ALo3.17 ALo3.14 2 Absolute half-channel gain. Receive filter gain = 0dB setting GAR1 GAR2 GAR3 -0.6 -12.9 -10.3 All other receive filter settings (-1 to -7dB) are in addition to 0dB setting GAR1 GAR2 GAR3 3 Gain tracking vs. input level CCITT G.714 Method 2 Typ‡ Max 5.704 5.906 Test Conditions µ-Law A-Law Vp-p Vp-p 0.95 -11.8 -9.1 dB dB dB PCM to SPKR± PCM to HSPKR±, RxA/u=0* PCM to HSPKR±, RxA/u=1* 1020Hz -0.15 -0.15 -0.15 +0.15 +0.15 +0.15 dB dB dB PCM to SPKR± PCM to HSPKR±, RxA/u=0* PCM to HSPKR±, RxA/u=1* from nominal 1020Hz GTR -0.3 -0.6 -1.6 0.3 0.6 1.6 dB dB dB 3 to -40 dBm0 -40 to -50 dBm0 -50 to -55 dBm0 4 Signal to total distortion vs. input level. CCITT G.714 Method 2 GQR 35 29 24 dB dB dB 0 to -30dBm0 -40 dBm0 -45 dBm0 5 Receive Idle Channel Noise NCR NPR 6 Gain relative to gain at 1020Hz 200 Hz 300-3000 Hz 3000-3400 Hz 4000 Hz >4600 Hz GRR 7 Absolute Delay DAR 240 µs at frequency of min. delay 8 Group Delay relative to DAR DDR 750 380 130 750 µs µs µs µs 500-600 Hz 600-1000 Hz 1000-2600 Hz 2600 - 2800 Hz 9 Crosstalk CTRT CTTR dB dB G.714.16 D/A to A/D A/D to D/A 0.2 -12.3 -9.7 Units -0.25 -0.90 15.5 -75 dBrnC0 dBrn0p 0.25 0.25 0.25 -12.5 -25 dB dB dB dB dB -74 -80 µ-Law A-Law † AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. * Note: RxA/u, refer to General Control Register, address 0Fh. AC Electrical Characteristics† for Side-tone Path Sym Min Typ‡ Max Units Test Conditions Absolute path gain Gain adjust = 0dB GAS1 GAS2 -17.2 -13.1 -16.7 -12.6 -16.2 -12.1 dB dB SIDEA/u, MICA/u, RxA/u all 0 SIDEA/u, MICA/u, RxA/u all 1 M± inputs to HSPKR± outputs 1000Hz All other settings (-9.96 to +9.96dB) GAS GAS -0.3 -0.3 +0.3 +0.3 dB dB SIDEA/u=0 SIDEA/u=1 from nominal relative measurements w.r.t. GAS1 & GAS2 Characteristics 1 † AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. 7-40 MT9092 AC Electrical Characteristics† for New Call Tone Characteristics 1 New Call Tone Output voltage (SPKR+ to SPKR-) Sym Typ‡ Units Test Conditions VNCT1 VNCT2 VNCT3 VNCT4 6.0 2.390 0.950 0.380 Vp-p Vp-p Vp-p Vp-p NCTG0=0, NCTG1=0 NCTG0=1, NCTG1=0 NCTG0=0, NCTG1=1 NCTG0=1, NCTG1=1 load > 34 ohms across SPKR± † AC Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. Electrical Characteristics† for Analog Outputs Characteristics Sym Min Typ‡ 260 300 ohms 300 pF each pin: % 300 ohms load across HSPKR± (tol-15%), Vo≤6.2Vp-p,RxA/u=1, Rx gain=0dB 1 Earpiece load impedance EZL 2 Allowable Earpiece capacitive load ECL 3 Earpiece harmonic distortion ED 4 Speaker load impedance SZL 5 Allowable Speaker capacitive load SCL 6 Speaker harmonic distortion SD Max 0.5 34 Units Test Conditions across HSPKR± HSPKR+ HSPKR- 40 ohms 300 pF each pin % 40 ohms load across SPKR± (tol-15%), VO≤6.2Vp-p, Rx gain=0dB 0.5 across SPKR± SPKR+ SPKR- † Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. Electrical Characteristics† for Analog Inputs Characteristics Sym 1 Differential input voltage without overloading CODEC VID 2 Input impedance ZI Min 50 Typ‡ Max Units Test Conditions 2.87 1.02 Vp-p Vp-p MICA/u=0, A/u=0 MICA/u=0, A/u=1 across MIC± or M± inputs, Tx filter gain = 0dB setting kΩ MIC+, MIC-, M+ or Mto VSS. † Electrical Characteristics are over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. 7-41 MT9092 AC Electrical Characteristics† - ST-BUS Timing (See Figure 12) Characteristics Sym Min Typ‡ Max Units 1 C4i Clock Period tC4P 243 244 245 ns 2 C4i Clock High Period tC4H 121 122 123 ns 3 C4i Clock Low Period tC4L 121 122 123 ns 4 C4i Clock Transition Time 20 50 ns 5 F0i Frame Pulse Setup Time tF0iS 50 ns 6 F0i Frame Pulse Hold Time tF0iH 50 ns 7 F0i Frame Pulse Width Low tF0iW 150 ns 8 DSTo Delay tDSToD 9 DSTi Setup Time tDSTiS 30 ns 10 DSTi Hold Time tDSTiH 50 ns tT 100 125 ns Test Conditions CL=50 pF † Timing is over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. tT tC4H tC4P C4i tT 1 bit cell 2.4V 0.4V tDSToD DSTo 2.4V 0.4V tDSTiS DSTi tDSTiH 2.4V 0.4V tT F0i 2.4V 0.4V tF0iH tF0iS tT tF0iW Figure 12 -ST-BUS Timing Diagram 7-42 tC4L MT9092 AC Electrical Characteristics† - Microport Timing (see Figure 13) Characteristics Sym Min Typ‡ Max Units Test Conditions 1 Receive data setup A 10 ns 2 Receive data hold B 10 ns 3 Transmit data delay from clock falling edge C 80 ns 50 pF 4 High Z to valid data from SCLK falling edge D 80 ns 50 pF 5 Valid data to high Z from CS rising edge E 80 ns 50 pF 6 Current transmit data hold from clock falling edge F 0 ns 7 Chip Select to SCLK setup and hold times G 0 ns 8 SCLK clock period (3 MHz) H 333 ns † Timing is over recommended temperature range & recommended power supply voltages. ‡ Typical figures are at 25°C and are for design aid only: not guaranteed and not subject to production testing. DATA 1 RECEIVE 0 1 2 7 B A H SCLK G G CS D E F C DATA 1 or DATA 2 TRANSMIT 0 1 2 6 7 Figure 13 - Serial Microport Timing Diagram 7-43 MT9092 NOTES: 7-44