ELECTRONICS Transient Voltage Suppressors 3.0SMC Series Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Transient Voltage Suppressors - 3.0SMC Series Features UNI 1. Halogen-free 2. Rohs compliant 3. Typical maximum temperature coefficient 4. ΔVBR = 0.1% x VBR@25°C x ΔT 5. Glass passivated Chip junction in DO-214AB package BI 6. 3000W peak pulse capadility at 10×1000μs waveform, repetition rate (duty cycles):0.01% 7. Fast response time:typically less than 1.0ps from 0 Volts to BV min 8. Excellent clamping capability 9. Low incremental surge resistance 10. Typical IR less than 5μA above 12V BI Cathode 11. High temperature soldering guaranteed:260°C/40seconds/0.375”,(9.5 Anode mm) lead length, 5lbs., (2.3kg) tension 12. Plastic package has underwriters laboratory flammability classification UNI 94v-0 Applications TVS devices are ideal for the protection of I/O interfaces,VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. Mechanical Characteristics Rating Symbol Value Units PPPM 3000 Watts PD 6.5 Watts IFSM 300 Amps VF 3.5 V Operating junction and Storage Temperature Range. TJ,TSTG -55°C to 175°C °C Typical Thermal Resistance Junction to Lead RuJL 15 °C/W Typical Thermal Resistance Junction to Ambient RuJA 75 °C/W Peak Pulse Power Dissipation by 10x1000μs test waveform (Fig.1)(Note 1) Steady State Power Dissipation on inifinite heat sink at TL=75°C (Fig. 5) Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional only (Note 2) Maximum Instantaneous Forward Voltage at 25A for Unidirectional only (Note 3) Notes: 1. Non-repetitive current pulse , per Fig. 3 and derated above TA = 25°C per Fig. 2. 2. Mounted on copper pad area of 0.31x0.31” (8.0 x 8.0mm) to each terminal. 3. Measured on 8.3ms single half sine wave or equivalent square wave for unidirectional device only, duty cycle=4 per minute maximum. Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:1 Transient Voltage Suppressors - 3.0SMC Series Electriacl Characteristics Reverse StandOff Voltage Type Number (UNI) (BI) 3.0SMC6.8A 3.0SMC6.8CA VRWM(V) 5.80 3.0SMC7.5A 3.0SMC7.5CA 6.40 Breakdown Voltage@IT VBR MIN.(V) VBR MAX.(V) Test Current 6.40 7.25 IT(mA) 10 7.22 8.30 10 Maximum Clamping Voltage@IPP VC(V) Peak Pulse Current 9.2 IPP(A) 326.1 11.2 267.3 Reverse Leakage @VRWM IR(µA) 800 800 3.0SMC8.2A 3.0SMC8.2CA 7.02 7.78 8.95 10 12.0 250.0 200 3.0SMC9.1A 3.0SMC9.1CA 7.78 8.33 9.58 1 12.9 232.6 100 3.0SMC10A 3.0SMC10CA 8.55 9.44 10.82 1 13.6 220.6 50 3.0SMC11A 3.0SMC11CA 9.40 10.00 11.50 1 18.2 164.8 5 3.0SMC12A 3.0SMC12CA 10.20 11.10 12.80 1 19.9 150.8 5 3.0SMC13A 3.0SMC13CA 11.10 12.20 14.00 1 21.5 139.5 5 3.0SMC15A 3.0SMC15CA 12.80 14.40 16.50 1 24.4 123.0 5 3.0SMC16A 3.0SMC16CA 13.60 15.60 17.90 1 26.0 115.4 5 3.0SMC18A 3.0SMC18CA 15.30 16.70 19.20 1 29.2 102.7 5 3.0SMC20A 3.0SMC20CA 17.10 18.90 21.70 1 32.4 92.6 5 3.0SMC22A 3.0SMC22CA 18.80 20.00 23.30 1 35.5 84.5 5 3.0SMC24A 3.0SMC24CA 20.50 22.20 25.50 1 38.9 77.1 5 3.0SMC27A 3.0SMC27CA 23.10 24.40 28.00 1 42.1 71.3 5 3.0SMC30A 3.0SMC30CA 25.60 28.90 33.20 1 48.4 62.0 5 3.0SMC33A 3.0SMC33CA 28.20 31.10 35.80 1 53.3 56.3 5 3.0SMC36A 3.0SMC36CA 20.80 33.30 38.30 1 58.1 51.6 5 3.0SMC39A 3.0SMC39CA 33.30 36.70 42.20 1 64.5 46.5 5 3.0SMC43A 3.0SMC43CA 36.80 40.00 46.00 1 69.4 43.2 5 3.0SMC47A 3.0SMC47CA 40.20 44.40 51.10 1 72.7 41.3 5 3.0SMC51A 3.0SMC51CA 43.60 47.80 54.90 1 82.4 36.4 5 3.0SMC56A 3.0SMC56CA 47.80 50.00 57.50 1 87.1 34.4 5 3.0SMC62A 3.0SMC62CA 53.00 56.70 65.20 1 96.8 31.0 5 3.0SMC68A 3.0SMC68CA 58.10 64.40 74.10 1 103.0 29.1 5 3.0SMC75A 3.0SMC75CA 64.10 71.10 81.80 1 121.0 24.8 5 3.0SMC82A 3.0SMC82CA 70.10 77.80 89.50 1 137.0 20.8 5 3.0SMC91A 3.0SMC91CA 77.80 86.70 99.70 1 146.0 20.6 5 3.0SMC100A 3.0SMC100CA 85.50 94.40 108.20 1 162.0 18.6 5 3.0SMC110A 3.0SMC110CA 94.00 100.00 115.50 1 177.0 16.8 5 3.0SMC120A 3.0SMC120CA 102.00 111.00 128.00 1 193.0 15.6 5 3.0SMC130A 3.0SMC130CA 111.00 122.00 140.50 1 209.0 14.4 5 3.0SMC150A 3.0SMC150CA 128.00 144.00 165.50 1 243.0 12.4 5 3.0SMC180A 3.0SMC180CA 154.00 167.00 192.60 1 292.0 10.3 5 3.0SMC200A 3.0SMC200CA 171.00 189.00 217.50 1 324.0 9.3 5 3.0SMC220A 3.0SMC220CA 185.00 209.00 243.20 1 356.0 8.4 5 Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:2 Transient Voltage Suppressors - 3.0SMC Series Ratings and Characteristic Curves Figure 1 - Peak Pulse Power Rating Curve Figure 2 - Pulse Derating Curve A Figure 3 - Pulse Waveform Figure 4 - Typical Junction Capacitance Figure 5 - Steady State Power Derating Curve Figure 6 - Maximum Non-Repetitive Peak Forward Surge Current Uni-Directional Only Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:3 Transient Voltage Suppressors - 3.0SMC Series Soldering Parameters Feflow Condition Pre Heat Lead-free assembly - Temperature Min (T s(min)) 150°C - Temperature Max (T s(min)) 200°C - Time (min to max) (t s) 60-180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3°C/second max TS(max) to TL - Ramp-up Rate 3°C/second max - Temperature (T L) (Liquidus) Reflow 217°C - Time (min to max) (t s) 60-150 seconds 260+0/-5 °C Peak Temperature (T P) Time within 5°C of actual peak Temperature (t p) 20-40 seconds Ramp-down Rate 6°C/second max Time 25°C to peak Temperature (T P) 8 minutes Max. Do not exceed 280°C Physical Specifications tp TP one Ramp-up Temperature (T) TL tL Critical Z P TL to T Weight 0.007 ounce, 0.21 grams JEDEC DO214AB. Molded plastic body over glass passivated junction Color band denotes cathode except Bidirectional. Matte Tin-plated leads, Solderable per JESD22-B102D Case Ts(max) Ts(min) Ramp-down ts Polarity Termina Preheat Time (t) Circuit Protection System Environmental Specifications Temperature Cycle JESD22-A104 Pressure Cooker JESD 22-A102 High Temp. Storage JESD22-A103 HTRB JESD22-A108 Thermal Shock JESD22-A106 Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:4 Transient Voltage Suppressors - 3.0SMC Series Dimensions Unit:mm DO-214AB (SMC -Bend) DIM Inches Millimeters Min Max Min Max A 0.114 0.126 2.900 3.200 B 0.260 0.280 6.600 7.110 C 0.220 0.245 5.590 6.220 D 0.079 0.103 2.060 2.620 E 0.030 0.060 0.760 1.520 F - 0.008 - 0.203 G 0.305 0.320 7.750 8.130 H 0.006 0.012 0.152 0.305 I 0.129 - 3.300 - J 0.094 - 2.400 - K - 0.165 - 4.200 L 0.094 - 2.400 - Warehouse Storage Conditions of Products · Storage Conditions: 1. Storage Temperature: -10°C~+40°C 2. Relative Humidity:≤75%RH 3. Keep away from corrosive atmosphere and sunlight. · Period of Storage: 1 year Circuit Protection System Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:5 RuiLongYuan Electronics Co., Ltd. · Reproducing and modifying information of the document is prohibited without permission from Ruilongyuan International Inc. · Ruilongyuan International Inc. reserves the rights to make changes of the content herein the document anytime without notification. Please refer to our website for the latest document. · Ruilongyuan International Inc. disclaims any and all liability arising out of the application or use of any product including damages incidentally and consequentially occurred. · Ruilongyuan International Inc. does not assume any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. · Applications shown on the herein document are examples of standard use and operation. Customers are responsible in comprehending the suitable use in particular applications.Ruilongyuan International Inc. makes no representation or warranty that such applications will be suitable for the specifed use without further testing or modifcation. · The products shown herein are not designed and authorized for equipments requiring high level of reliability or relating to human life and for any applications concerning life-saving or life-sustaining, such as medical instruments, transportation equipment,aerospace machinery et cetera. Customers using or selling these products for use in such applications do so at their own risk and agree to fullyindemnify Ruilongyuan International Inc. for any damages resulting from such improper use or sale. Tel: +86-755-8290 8296 Circuit Protection System Fax: +86-755-8290 8002 E-mail: [email protected] Specifications are subject to change without notice. Please refer to http://www.ruilon.com for current information. Page:6