PHILIPS SAA2032

INTEGRATED CIRCUITS
DATA SHEET
SAA2032
Digital equalization for the tape
drive processing of the DCC system
Product specification
Supersedes data of February 1993
File under Integrated Circuits, Miscellaneous
Philips Semiconductors
February 1995
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
FEATURES
• Analog-to-digital conversion, demultiplexing,
equalization and zero crossing of time multiplexed
analog read amplifier signal
• Microcontroller interface
• Search mode envelope, label and virgin detection of the
AUX channel
• Search mode tape speed measurement
GENERAL DESCRIPTION
• Simplified external biassing
Performing the Digital Equalizing function in the Digital
Compact Cassette (DCC) system, the SAA2032 is
intended for use in conjunction with the SAA2022, read
amplifier TDA1317 or TDA1318.
• Reduced power consumption
• Analog eye output
• 4 V nominal operating voltage capability.
ORDERING INFORMATION
EXTENDED TYPE
NUMBER
SAA2032GP
PACKAGE
PINS
PIN POSITION
MATERIAL
CODE
44
QFP 1
plastic
SOT205AG
Note
1. When using reflow soldering it is recommended that the Dry Packing instructions in the Quality Reference Pocketbook
are followed. The pocketbook can be ordered using the code 9398 510 34011.
February 1995
2
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
VDDAD
VDD
11
12
3
f 24
43
CLOCK
GENERATION
2
37
SAA2032
VIRGIN
LABEL
DETECTOR
36
38
VIN
5
ADC
DEMUX
FILTER
SLICER
22
23
24
25
26
27
28
29
30
1
44
15
DAC
LTENDEQ
LTCNT1
LTCNT0
LTCLK
RDSYNC
LABEL
VIRGIN
AENV
CH0
CH1
CH2
CH3
CH4
CH5
CH6
CH7
AUX
DIGEYE
VAL
ANEYE
32
33
31
LT
INTERFACE
34
35
8, 14
10
13, 17, 39
MEA663
V SSA
V SSAD
Fig.1 Block diagram.
February 1995
RDCLK
3
V SS
LTDATA
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
PINNING
SYMBOL
DIGEYE
PIN
1
DESCRIPTION
serial data output for eye pattern
RDSYNC
2
SYNC data for Read Amplifier (push-pull output)
RDCLK
3
data clock for Read Amplifier (push-pull output)
TEST1
4
test 1; to be connected to VSS
VIN
5
analog time multiplexed input from Read Amplifier
REFN
6
lower reference voltage (+1 V) for ADC
REFP
7
upper reference voltage (+3.1 V) for ADC
VSSA
8
analog ground (0 V)
BIASA
9
bias current for ADC (sinks current from VDDAD via 33 kΩ)
VSSAD
10
supply ground (0 V) for ADC
VDDAD
11
supply voltage (+5 V) for ADC
VDD
12
supply voltage (+5 V)
VSS
13
supply ground (0 V)
VSSA
14
supply ground (0 V)
ANEYE
15
analog eye voltage output
n.c.
16
not connected
VSS
17
supply ground (0 V)
TEST4
18
test 4; do not connect
TEST5
19
test 5; do not connect
TEST6
20
test 6; do not connect
TEST7
21
test 7; do not connect
CH0
22
channel 0 output for SAA2022 (DCC Drive Signal Processing) (push-pull output)
CH1
23
channel 1 output for SAA2022 (push-pull output)
CH2
24
channel 2 output for SAA2022 (push-pull output)
CH3
25
channel 3 output for SAA2022 (push-pull output)
CH4
26
channel 4 output for SAA2022 (push-pull output)
CH5
27
channel 5 output for SAA2022 (push-pull output)
CH6
28
channel 6 output for SAA2022 (push-pull output)
CH7
29
channel 7 output for SAA2022 (push-pull output)
AUX
30
AUX channel output for SAA2022 (push-pull output)
LTDATA
31
microcontroller I/O data interface (3-state push-pull output and input; CMOS levels)
LTENDEQ
32
microcontroller interface enabling (CMOS input levels)
LTCNT1
33
microcontroller interface; mode control 1 (CMOS input levels)
LTCNT0
34
microcontroller interface; mode control 0 (CMOS input levels)
LTCLK
35
microcontroller bit-clock interface (CMOS input levels)
VIRGIN
36
search mode virgin detection output
LABEL
37
search mode label detection output
AENV
38
search mode auxiliary detection output
VSS
39
supply ground (0 V)
February 1995
4
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SYMBOL
SAA2032
PIN
DESCRIPTION
AENV
LABEL
VIRGIN
LTCLK
LTCNT0
38
37
36
35
34
synchronization output for DIGEYE
VSS
44
39
VAL
TEST8
clock input; typical frequency 24.576 MHz (CMOS input)
TEST9
43
40
f24
TEST10
test 10 input; to be connected to VSS
41
test 9 input; to be connected to VSS
42
42
41
TEST10
f24
TEST9
VAL
test 8 input; to be connected to VSS
43
40
44
TEST8
DIGEYE
1
33
LTCNT1
RDSYNC
2
32
LTENDEQ
RDCLK
3
31
LTDATA
TEST1
4
30
AUX
VIN
5
29
CH7
REFN
6
28
CH6
SAA2032
REFP
7
27
CH5
VSSA
8
26
CH4
BIASA
Fig.2 Pin configuration.
February 1995
5
22
CH0
21
TEST7
20
TEST6
19
TEST5
TEST4
V SS
n.c.
ANEYE
VSSA
VSS
V DD
18
CH1
17
23
16
CH2
11
15
10
VDDAD
14
CH3
24
13
25
12
9
VSSAD
MEA661
February 1995
DAIO
TDA1315
DAC
SAA7323
ADC
SAA7360
AUDIO INPUT/OUTPUT
digital output
digital input
analog
output
analog
input
I S
2
RECORDING + PLAY BACK
6
I 2S
(sub-band)
MEA695 - 2
digital
equalizer
SAA2032
TDA1317 or
TDA1318
read
write
TAPE DRIVE PROCESSING
256 kbits
RAM
SAA2022
TDA1316 or
TDA1319
speed control
heads
and
tape
capstan
drive
Digital equalization for the tape
drive processing of the DCC system
Fig.3 DCC data flow diagram.
MICROCONTROLLER
PASC PROCESSING
adaptive
allocation and
scale factors
SAA2012
SAA2002
stereo filter
codec
Philips Semiconductors
Product specification
SAA2032
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
Following A/D conversion the envelope of this signal is
filtered and sliced. This forms the Alternating Envelope
AENV output. The LABEL and VIRGIN outputs are
detected from this and the tape search speed measured.
FUNCTIONAL DESCRIPTION
Operating Modes
DEQ operating modes are programmed via the LT
interface:
OFF
NORMAL
In the OFF mode the RDSYNC and RDCLK signals are
HIGH, the EYE outputs are disabled and the channel and
auxiliary outputs (CH0 to CH7 and AUX) are 3-stated.
• A/D conversion
• Demultiplexing
• Equalization
Read Amplifier interface
• Zero crossing.
The interface between the Read Amplifier and the
SAA2032 consists of three signals:
in this mode the SAA2032 performs the equalization and
slicing of the eight data channels and the auxiliary channel.
The eight data channels have a bit-rate of 96 kbits/s while
the auxiliary channel has a bit-rate of 12 kbits/s.
1.
VIN from Read Amplifier to SAA2032; time
multiplexed data.
The SAA2032 input is a time-multiplexed analog signal
from the Read Amplifier. The signal contains ten time slots,
of which nine are used. The Read Amplifier and the
SAA2032 synchronize with the RDCLK and RDSYNC
signals generated by the SAA2032.
2.
RDSYNC from SAA2032 to Read Amplifier;
synchronization between Read Amplifier multiplexer
and SAA2032 demultiplexer.
3.
RDCLK from SAA2032 to Read Amplifier; data clock
for Read Amplifier multiplexer.
Following A/D conversion and demultiplexing the nine
channels are equalized. The encoding of the equalizing
coefficients (12 per channel) are not fixed and must be
loaded via the LT interface before operation.
The multiplexed VIN output of the Read Amplifier changes
to another channel at the rising edge of RDCLK. RDSYNC
synchronizes the Read Amplifier VIN output: if RDSYNC is
HIGH, the rising edge of the RDCLK will select the AUX
channel.
The nine equalized output signals are up-sampled by a
factor of 10 with the resulting signals fed to the slicer. The
slicer output is applied to the SAA2022.
Figures 4 and 5 show the relationship between the
SAA2032 and the Read Amplifier.
TEST
SAA2022 interface
• A/D conversion
• Demultiplexing
The interface with the SAA2022 consists of the 9 data
output signals CH0 to CH7, AUX.
• Equalization
Table 1
• Zero crossing
• Eye-pattern.
OPERATIONAL MODE
Same as normal mode. In addition the digital and analog
eye-pattern outputs are enabled. The eye-pattern output
corresponds to one of the equalized channel outputs.
SEARCH
• A/D conversion
• Envelope detection
RDSYNC
RDCLK
Normal
YES
YES
Test
YES
YES
Search
HIGH
YES
Off
HIGH
HIGH
Label and virgin detection interface
• Tape search and speed measurement.
When the DCC player is in its search mode, the tape is
fast-wound while the head retains tape contact. The
SAA2032 can be made to operate in the search mode and
the information will be read from the auxiliary tape track.
In the search mode the analog input signal from the Read
Amplifier is not the multiplexed signal but only the auxiliary
channel signal.
February 1995
Dependency of Read Amplifier on
operational mode.
7
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
tape speed must be known. In search mode the SAA2032
assesses the speed of labelled tapes. The microcontroller
obtains this information via the LT-interface.
The following three signals are generated:
1.
LABEL: label detection (HIGH if label is detected).
2.
VIRGIN: virgin tape detection (HIGH if virgin tape
is detected).
The speed information is encoded in 3 variables:
AENV: alternating envelope (sliced envelope).
1.
SVF Speed Validation Flag (HIGH if invalid).
AENV, LABEL and VIRGIN are disabled in normal or off
modes. LABEL, VIRGIN and AENV are LOW.
2.
SC (4..0) Speed counter.
3.
3.
SR (1..0) Speed Range.
51.2
SR
Search speed = 2 × ----------- x normal speed.
SC
If SC = 0 then search speed > 51.2.
AENV, LABEL and VIRGIN are enabled when the
SAA2032 is in search mode.
The device detects the envelope AENV of the auxiliary
track at search speeds between 3 and 50 times normal
speed. If AENV is continuously HIGH (label detection),
LABEL will be HIGH.
With SR = 0, 1, 2 or 3 and SC = 0 to 31.
If SVF = 1 then SR and SC values are invalid.
Appendix 1 gives a table of the search mode speed
control.
When AENV is continuously LOW (virgin tape detection)
VIRGIN will be HIGH.
Figures 6, 7 and 8 show the relationship between AENV,
VIRGIN and LABEL.
Microcontroller (LT) Interface
The SAA2032 is able to exchange information with the
microcontroller via the LT-interface. The microcontroller
performs as master, the SAA2032 as slave.
Labelled tape-speed calculation
When the DCC player is in its search mode, the tape
speed increases. LABEL information is encoded
throughout its length. To examine the length of a label, the
Figure 9 gives the operation of the LT-interface.
RDCLK
VIN
CH7 AUX
***
CH0 CH1 CH2 CH3 CH4 CH5 CH6 CH7 AUX
***
CH0 CH1
RDSYNC
MCD477
Fig.4 Signals on interface between Read Amplifier and SAA2032.
February 1995


8
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
RDCLK
t su
VIN
VIN
stable
MCD478
tsu > 80 ns; set-up time VIN before RDCLOCK HIGH.
Typical frequency for RDCLK = 3.072 MHz.
Typical frequency for RDSYNC = 307.2 kHz.
Fig.5 Timing.
signal
from
tape
t d1
t d2
AENV
MCD488 - 1
td1 = td2 = between 0.5 and 1.0 auxiliary block lengths.
Fig.6 Diagram of AENV signal.
February 1995
9
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
AENV
t d4
t d3
LABEL
MLA635 - 2
td3 = between 4 and 12 auxiliary blocks.
td4 = between 4 and 12 auxiliary blocks.
Fig.7 AENV and LABEL signals.
AENV
t d6
t d5
VIRGIN
MLA634 - 2
td5 = td6 = between 4 and 12 auxiliary blocks.
Fig.8 AENV and VIRGIN signals.
February 1995
10
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
LTENDEQ
LTCNT 0/1
LTCLK
LTDATA
0
LSB
1
2
3
4
5
6
7
MSB
MCD479
Fig.9 Typical operation of the LT-interface.
LTCNT specification
Table 2
Four types of data exchange performed on the interface.
LTCNT1
LTCNT0
0
0
data
0
1
1
1
February 1995
LT DATA EXCHANGE MODE
FROM
TO
write
µC
DEQ
data
read
DEQ
µC
0
address
write
µC
DEQ
1
mode settings
write
µC
DEQ
11
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
Mode Settings Load (LTCNT = 11) (See Fig.10)
Address Information Load (LTCNT = 10) (See Fig.11)
The 8-bits transmitted under ’mode settings load’ control
both the ’operation mode’ and the ’data exchange type’.
A channel/tap combination can be selected through this
type of data exchange.
Table 3
Co-efficient Data Load (LTCNT = 00) (See Fig.12)
Mode settings; ’operation mode’.
a1
a0
0
0
normal
0
1
test
1
0
search
1
1
off
This type of data exchange will overwrite the equalizer tap
coefficient of the current selected channel/tap
combination.
OPERATION MODE
The coefficient data for tap <0000> of the auxiliary channel
should always be zero.
Data Read (LTCNT = 01) (See Fig.13)
Table 4
Mode settings; ’data exchange type’.
b1
b0
DATA
EXCHANGE
0
0
write
coefficient
data
0
1
read
coefficient
data
1
1
read
envelope
data
This type of data exchange will send information from the
LTDATA register in the SAA2032 to the microcontroller.
Data in the LTDATA register depends upon the current
data exchange type.
TYPE
LTDATA interpretation:
• coefficient data: two’s complement coefficient data
Remark post condition: after every communication
sequence the data exchange type must be set to “read
coefficient data”.
• tape speed data
– d7 = SVF flag
– d6 to d2 = SC4 to SC0
– d1, d0 = SR1, SR0.
Tape speed data format is shown in Fig.14.
MSB
*
LSB
*
*
*
b1
b0
a1
a0
MCD480
data
exchange
type
operation
mode
Fig.10 Mode settings load (LTCNT = 11).
February 1995
12
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
c3
c2
c1
c0
t3
t2
t1
SAA2032
d7
t0
d6
d5
d4
d3
d2
d1
d0
MCD482
MCD481
MSB
MSB
LSB
LSB
c3 to c0 --> channel number <0000 to 0111>
+ auxiliary channel <1000>
t3 to t0 --> tap number <0000 .. 1011>
Fig.11 Address information load (LTCNT = 10).
Fig.12 Coefficient data load (LTCNT = 00).
d7
d7
d6
d5
d4
d3
d2
d1
d0
d0
MCD483
MSB
MBC381
LSB
SVF
Fig.13 Read data (LTCNT = 01).
February 1995
SC (h. . .0)
SR (1. . .0)
Fig.14 Tape speed data format.
13
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
t Le
LTENDEQ
t su1
t h1
t h2
LTCNT0/1
t su4
t su2
t Lc
tHc
LTCLK
t su3
t h3
LTDATA
bit
1
0
tLe > 120 ns; minimum LOW time LTENDEQ before transfer.
tsu1 > 20 ns; set-up time LTCNT0/1 before LTENDEQ HIGH.
th1 > 100 ns; hold time LTCNT0/1 after LTENDEQ HIGH.
tsu2 ≥ 0 ns; set-up time LTCNT0/1 before LTCLK LOW.
th2 > 20 ns; hold time LTENDEQ after LTCLK HIGH.
tLc > 120 ns; minimum LOW time LTCLK.
tHc > 120 ns; minimum HIGH time LTCLK.
tsu4 > 200 ns; set-up time LTCLK before LTENDEQ HIGH.
tsu3 > 100 ns; set-up time LTDATA before LTCLK HIGH.
th3 > 20 ns; hold time LTDATA after LTCLK HIGH.
Fig.15 Microcontroller to SAA2032 timing.
February 1995
14
MCD485 - 1
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
t Le
LTENDEQ
t su1
t h2
t h1
LTCNT0/1
t su4
t su2
t Lc
tHc
LTCLK
t d1
t h5
t d2
t h6
LTDATA
bit
1
0
tLe > 120 ns; minimum LOW time LTENDEQ before transfer.
tsu1 > 20 ns; set-up time LTCNT0/1 before LTENDEQ HIGH.
th1 > 100 ns; hold time LTCNT0/1 after LTENDEQ HIGH.
tsu2 ≥ 0 ns; set-up time LTCNT0/1 before LTCLK LOW.
th2 > 20 ns; hold time LTENDEQ after LTCLK HIGH.
tLc > 120 ns; minimum LOW time LTCLK.
tHc > 120 ns; minimum HIGH time LTCLK.
tsu4 > 200 ns; set-up time LTCLK before LTENDEQ HIGH.
td1 > 300 ns; maximum delay LTDATA after LTENDEQ HIGH.
td2 > 400 ns; maximum delay LTDATA after LTCLK HIGH.
th5 > 160 ns; hold time LTDATA after LTCLK HIGH.
th6 > 0 ns; hold time LTDA after LTENDEQ LOW.
Fig.16 SAA2032 to Microcontroller timing.
February 1995
15
MCD486 - 1
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
Eye pattern output
Table 5
Eye outputs.
To test equalization performance it is possible to output the
equalized channels. For this purpose one analog and two
digital output signals are provided. Selection of the EYE
pattern output is determined by the last channel address
sent to the SAA2032.
OPERATION MODE
Search
• DIGEYE: serial data line for 8-bits output value
Off
Normal
Test
• VAL: validation signal for data bits
DIGEYE
ANEYE
LOW
HIGH
ENABLED
ENABLED
LOW
HIGH
LOW
HIGH
The internal number representation in the SAA2032 is in
two's complement. The format of the selected 8-bits will be
converted to the off-set-binary format. This means that the
MSB of the two's complement number has been inverted.
This 8-bit number is shifted out via the DIGEYE output.
• ANEYE: analog eye voltage output.
The eye outputs are enabled in test mode.
Figure 17 gives the eye pattern output timing.
t val
t eye
VAL
RDCLK
DIGEYE
LSB
MSB
(inverted)
LSB
RDCLK
th
t clk
t su
DIGEYE
MEA662 - 1
stable
data
tval = 1/4 clock period; pulse width HIGH.
tsu > 60 ns; minimum set-up time data before clock.
th > 5 ns; minimum hold time data after clock.
tclk = 1/fclk.
fclk = 3.072 MHz; nominal DIGEYE clock frequency.
teye = 1/feye.
feye = 307.2 kHz; nominal DIGEYE clock frequency.
Fig.17 Timing diagram.
February 1995
16
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
CONDITIONS
MIN.
MAX.
UNIT
−0.5
+6.5
V
−0.5
VDD + 0.5
V
−
−100
mA
−
100
mA
input current
−10
10
mA
IO
output current
−20
20
mA
Ptot
total power dissipation
−
550
mW
Tstg
storage temperature
−55
+150
°C
Tamb
operating ambient temperature
−40
+85
°C
Ves1
electrostatic handling
note 2
−1500
+1500
V
Ves2
electrostatic handling
note 3
−70
+70
V
VDD
supply voltage
VI
input voltage
ISS
supply current in VSS
IDD
supply current in VDD
II
note 1
Notes
1. Input voltage should not exceed 6.5 V unless otherwise specified.
2. Equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor.
3. Equivalent to discharging a 200 pF capacitor through a 0 Ω series resistor.
DC CHARACTERISTICS
VDD = 3.8 to 5.5 V; Tamb = −40 to +85 °C; unless otherwise specified.
SYMBOL
PARAMETER
Supply
VDD
supply voltage
VDDAD
supply voltage for ADC
IDD
supply current
IDDAD
IOP
supply current for ADC
operating current
CONDITIONS
HIGH level input voltage
II
input current
TYP.
MAX.
UNIT
3.8
5.0
5.5
V
note 1
3.8
5.0
5.5
V
VDD = 5 V; note 2
−
22
26
mA
VDD = 3.8 V; note 2
−
12
14
mA
VDDAD = 5 V
−
11
13
mA
VDDAD = 3.8 V
−
5
7
mA
note 3
1.3
1.9
3.4
mA
0
−
0.3VDD
V
0.7VDD
−
VDD
V
VI = 0 V; Tamb = 25 °C −
−
−10
µA
VI = VDD; Tamb = 25 °C −
−
10
µA
Inputs f24, LTCLK, LTCNT0, LTCNT1 and LTENDEQ
LOW level input voltage
VIL
VIH
MIN.
Input REFP
Vrefp
reference voltage
2.7
3.1
3.4
V
Input REFN
Vrefn
reference voltage
0.7
1.0
1.4
V
February 1995
17
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SYMBOL
PARAMETER
SAA2032
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Inputs REFP and REFN
∆Vref
reference voltage difference
between REFP and REFN
2
2.1
2.7
V
VI(p-p)
input voltage (peak-to-peak)
Vrefn
−
Vrefp
V
−
−
100
µA
−
0.4
V
Input VIN
II
input current
Digital outputs
VOL
LOW level output voltage
note 4
−
VOH
HIGH level output voltage
note 4
VDD − 0.5 −
−
V
Output ANEYE
VO
output voltage
note 4
−
−
VDDAD
V
VO
output voltage range
note 4
−
1.1
−
V
−
Input/output LTDATA
VOL
LOW level output voltage
IO = −3 mA
−
VOH
HIGH level output voltage
IO = 2 mA
VDD − 0.5 −
IOZ
leakage current with outputs
in 3-state
VI = 0 V; Tamb = 25 °C −
0.4
V
−
V
−
10
µA
VI = VDD; Tamb = 25 °C −
−
10
µA
VIL
LOW level input voltage
−
−
0.3VDD
V
VIH
HIGH level input voltage
0.7VDD
−
−
V
Notes
1. VDDAD should never be lower than VDD − 0.2 V.
2. For load impedances in a typical application circuit.
3. Operating reference current for the specified range of Vrefp allowing for the tolerance on the internal resistor.
4. For outputs DIGEYE, RDSYNC, RDCLK, CH0 to CH7, AUX and VAL the maximum load current is 1 mA. For ANEYE
output the maximum load current is 10 µA. For VIRGIN, LABEL and AENV the maximum load current is 2 mA.
February 1995
18
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
AC CHARACTERISTICS
VDD = 3.8 to 5.5 V; Tamb = −40 to 85 °C; unless otherwise specified.
SYMBOL
VIN
Ci
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
−
−
15
pF
−
−
10
pF
23
24.576
26
MHz
pulse width LOW or HIGH
10
−
−
ns
Inputs LTCLK, LTENDEQ, LTCNT0 and LTCNT1
set-up time to f24
note 1
tsu
10
−
−
ns
30
−
−
ns
input capacitance
All digital inputs
Ci
input capacitance
Clock input f24
f
clock frequency
tp
th
hold time from f24
note 1
All outputs
Ci
input capacitance
−
−
10
pF
CL
load capacitance
−
−
50
pF
td
propagation delay time from f24 note 1
−
−
80
ns
Input/output LTDATA
input capacitance
Ci
−
−
10
pF
CL
load capacitance
−
−
50
pF
td
propagation delay time from f24
−
−
80
ns
tsu
set-up time to f24
note 1
10
−
−
ns
th
hold time from f24
note 1
30
−
−
ns
Note
1. LOW-to-HIGH transition.
February 1995
19
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
CONVERTER CHARACTERISTICS
VDD = 3.8 to 5.5 V; Tamb = −40 to 85 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
Analog-to-Digital Converter; VIN
resolution
conversation data available after
effective input bandwidth
6-bit resolution
at fs = 3.1 MHz
differential non-linearity
note 1
MIN.
TYP.
MAX.
UNIT
−
7
−
−
2 × tcy
−
0.5
−
−
MHz
−
−
±0.99
LSB
0.7
1.0
1.4
V
bits
Vrefn
reference voltage at VREFN
Vrefp
reference voltage at VREFP
2.7
3.1
3.4
V
∆Vref
reference voltage difference
between REFP and REFN
2
2.1
2.7
V
Vi
input voltage
Vrefn
−
Vrefp
V
S+THD/N
signal-to-total harmonic
distortion and noise ratio
21
−
−
dB
Ci
input capacitance
−
−
15
pF
II
input current (DC)
−
−
100
µA
−
6
−
bits
note 2
note 3
Digital-to-analog converter; output ANEYE
resolution
VO
output voltage
note 4
−
−
VDDAD
V
VO
output voltage range
note 4
−
1.1
−
V
Notes
1. Vrefp is supplied externally.
Vrefn is derived internally and set to 1/3Vrefp.
Vrefn must be decoupled externally at pin 6 via a 100 nF capacitor.
2. Signal level (fs) −20 dB, at any DC level within the input voltage range.
3. The output impedance of the analog input signal source must be <150 Ω.
4. Load impedance ≥1 MΩ.
February 1995
20
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
APPENDIX 1
Search Mode Speed Control Interface
In search mode the SAA2032 measures the tape speed. The tape speed is encapsulated in the variables:
• SVF Speed Validation Flag; is HIGH if NOT valid
• SC Speed Counter
• SR Speed Range.
The values in Table 6 represent the speed in multiples of the nominal tape speed of 4.76 cm/s.
Table 6
Speed in multiples of nominal tape speed.
SC[4 .. 0]
SR[1 .. 0]
0
1
2
3
0
>51.20
>102.40
>204.80
>409.60
1
51.20
102.40
204.80
409.60
2
25.60
51.20
102.40
204.80
3
17.07
34.13
68.27
136.53
4
12.80
25.60
51.20
102.40
5
10.24
20.48
40.96
81.92
6
8.53
17.07
34.13
68.27
7
7.31
14.63
29.26
58.51
8
6.40
12.80
25.60
51.20
9
5.69
11.38
22.76
45.51
10
5.12
10.24
20.48
40.96
11
4.65
9.31
18.62
37.24
12
4.27
8.53
17.07
34.13
13
3.94
7.88
15.75
31.51
14
3.66
7.31
14.63
29.26
15
3.41
6.83
13.65
27.31
16
3.20
6.40
12.80
25.60
17
3.01
6.02
12.05
24.09
February 1995
21
REMARKS
shift to higher speed range
normal working area
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SC[4 .. 0]
SAA2032
SR[1 .. 0]
0
1
2
3
18
2.84
5.69
11.38
22.76
19
2.69
5.39
10.78
21.56
20
2.56
5.12
10.24
20.48
21
2.44
4.88
9.75
19.50
22
2.33
4.65
9.31
18.62
23
2.23
4.45
8.90
17.81
24
2.13
4.27
8.53
17.07
25
2.05
4.10
8.19
16.38
26
1.97
3.94
7.88
15.75
27
1.90
3.79
7.59
15.17
28
1.83
3.66
7.31
14.63
29
1.77
3.53
7.06
14.12
30
1.71
4.41
6.83
13.65
31
1.65
3.30
6.61
13.21
February 1995
22
REMARKS
shift to lower speed range
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
PACKAGE OUTLINE
seating plane
S
0.15 S
19.2
18.2
44
34
B
33
1
2.4 (4x)
1.8
pin 1 index
0.15 M B
1.0
14.1
13.9
19.2
18.2
23
11
0.50
0.35
22
12
1.0
2.4
1.8 (4x)
0.50
0.35
X
0.15 M A
14.1
13.9
A
2.3
2.1
1.2
0.9
0.25
0.05
2.0
1.2
detail X
Dimensions in mm.
Fig.18 44-lead quad flat-pack; plastic (SOT205AG).
February 1995
23
2.60
2.15
0.25
0.14
0 to 7 o
MBC659 - 1
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
Several techniques exist for reflowing; for example,
thermal conduction by heated belt, infrared, and vapourphase reflow. Dwell times vary between 50 and 300 s
according to method. Typical reflow temperatures range
from 215 to 250 °C.
SOLDERING
Quad flat-packs
BY WAVE
During placement and before soldering, the component
must be fixed with a droplet of adhesive. After curing the
adhesive, the component can be soldered. The adhesive
can be applied by screen printing, pin transfer or syringe
dispensing.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 min at 45 °C.
REPAIRING SOLDERED JOINTS (BY HAND-HELD SOLDERING
IRON OR PULSE-HEATED SOLDER TOOL)
Fix the component by first soldering two, diagonally
opposite, end pins. Apply the heating tool to the flat part of
the pin only. Contact time must be limited to 10 s at up to
300 °C. When using proper tools, all other pins can be
soldered in one operation within 2 to 5 s at between 270
and 320 °C. (Pulse-heated soldering is not recommended
for SO packages.)
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder bath is
10 s, if allowed to cool to less than 150 °C within 6 s.
Typical dwell time is 4 s at 250 °C.
A modified wave soldering technique is recommended
using two waves (dual-wave), in which, in a turbulent wave
with high upward pressure is followed by a smooth laminar
wave. Using a mildly-activated flux eliminates the need for
removal of corrosive residues in most applications.
For pulse-heated solder tool (resistance) soldering of VSO
packages, solder is applied to the substrate by dipping or
by an extra thick tin/lead plating before package
placement.
BY SOLDER PASTE REFLOW
Reflow soldering requires the solder paste (a suspension
of fine solder particles, flux and binding agent) to be
applied to the substrate by screen printing, stencilling or
pressure-syringe dispensing before device placement.
February 1995
24
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress rating only and operation of
the device at these or at any other conditions above those given in the Characteristics sections of the specification is
not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
The Digital Compact Cassette logo is a registered trade mark of Philips Electronics N.V.
February 1995
25
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
NOTES
February 1995
26
Philips Semiconductors
Product specification
Digital equalization for the tape
drive processing of the DCC system
SAA2032
NOTES
February 1995
27
Philips Semiconductors – a worldwide company
Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428)
BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. (02)805 4455, Fax. (02)805 4466
Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213,
Tel. (01)60 101-1236, Fax. (01)60 101-1211
Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands,
Tel. (31)40 783 749, Fax. (31)40 788 399
Brazil: Rua do Rocio 220 - 5th floor, Suite 51,
CEP: 04552-903-SÃO PAULO-SP, Brazil.
P.O. Box 7383 (01064-970).
Tel. (011)829-1166, Fax. (011)829-1849
Canada: INTEGRATED CIRCUITS:
Tel. (800)234-7381, Fax. (708)296-8556
DISCRETE SEMICONDUCTORS: 601 Milner Ave,
SCARBOROUGH, ONTARIO, M1B 1M8,
Tel. (0416)292 5161 ext. 2336, Fax. (0416)292 4477
Chile: Av. Santa Maria 0760, SANTIAGO,
Tel. (02)773 816, Fax. (02)777 6730
Colombia: Carrera 21 No. 56-17, BOGOTA, D.E., P.O. Box 77621,
Tel. (571)217 4609, Fax. (01)217 4549
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. (032)88 2636, Fax. (031)57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. (9)0-50261, Fax. (9)0-520971
France: 4 Rue du Port-aux-Vins, BP317,
92156 SURESNES Cedex,
Tel. (01)4099 6161, Fax. (01)4099 6427
Germany: P.O. Box 10 63 23, 20095 HAMBURG ,
Tel. (040)3296-0, Fax. (040)3296 213
Greece: No. 15, 25th March Street, GR 17778 TAVROS,
Tel. (01)4894 339/4894 911, Fax. (01)4814 240
Hong Kong: 15/F Philips Ind. Bldg., 24-28 Kung Yip St.,
KWAI CHUNG, Tel. (0)4245 121, Fax. (0)4806 960
India: PEICO ELECTRONICS & ELECTRICALS Ltd.,
Components Dept., Shivsagar Estate, Block 'A',
Dr. Annie Besant Rd., Worli, BOMBAY 400 018,
Tel. (022)4938 541, Fax. (022)4938 722
Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4,
P.O. Box 4252, JAKARTA 12950,
Tel. (021)5201 122, Fax. (021)5205 189
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. (01)640 000, Fax. (01)640 200
Italy: Viale F. Testi, 327, 20162 MILANO,
Tel. (02)6752.1, Fax. (02)6752.3350
Japan: Philips Bldg 13-37, Kohnan 2 -chome, Minato-ku, KOKIO 108,
Tel. (03)3740 5101, Fax. (03)3740 0570
Korea: (Republic of) Philips House, 260-199 Itaewon-dong,
Yongsan-ku, SEOUL, Tel. (02)794-5011, Fax. (02)798-8022
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,
SELANGOR, Tel. (03)757 5511, Fax. (03)757 4880
Mexico: Philips Components, 5900 Gateway East, Suite 200,
EL PASO, TX 79905, Tel. 9-5(800)234-7381, Fax. (708)296-8556
Netherlands: Postbus 90050, 5600 PB EINDHOVEN,
Tel. (040)78 37 49, Fax. (040)78 83 99
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. (09)849-4160, Fax. (09)849-7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. (22)74 8000, Fax. (22)74 8341
Philips Semiconductors
Pakistan: Philips Markaz, M.A. Jinnah Rd., KARACHI 3,
Tel. (021)577 039, Fax. (021)569 1832
Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc,
106 Valero St. Salcedo Village, P.O. Box 911, MAKATI,
Metro MANILA, Tel. (02)810 0161, Fax. (02)817 3474
Portugal: Av. Eng. Duarte Pacheco 6, 1009 LISBOA Codex,
Tel. (01)683 121, Fax. (01)658 013
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. (65)350 2000, Fax. (65)251 6500
South Africa: 195-215 Main Road, Martindale,
P.O. Box 7430,JOHANNESBURG 2000,
Tel. (011)470-5433, Fax. (011)470-5494
Spain: Balmes 22, 08007 BARCELONA,
Tel. (03)301 6312, Fax. (03)301 42 43
Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM,
Tel. (0)8-632 2000, Fax. (0)8-632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. (01)488 2211, Fax. (01)481 7730
Taiwan: 69, Min Sheng East Road, Sec 3, P.O. Box 22978,
TAIPEI 10446, Tel. (2)509 7666, Fax. (2)500 5899
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
60/14 MOO 11, Bangna - Trad Road Km. 3
Prakanong, BANGKOK 10260,
Tel. (2)399-3280 to 9, (2)398-2083, Fax. (2)398-2080
Turkey: Talatpasa Cad. No. 5, 80640 LEVENT/ISTANBUL,
Tel. (0212)279 2770, Fax. (0212)269 3094
United Kingdom: Philips Semiconductors Limited, P.O. Box 65,
Philips House, Torrington Place, LONDON, WC1E 7HD,
Tel. (071)436 41 44, Fax. (071)323 03 42
United States: INTEGRATED CIRCUITS:
811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. (800)234-7381, Fax. (708)296-8556
DISCRETE SEMICONDUCTORS: 2001 West Blue Heron Blvd.,
P.O. Box 10330, RIVIERA BEACH, FLORIDA 33404,
Tel. (800)447-3762 and (407)881-3200, Fax. (407)881-3300
Uruguay: Coronel Mora 433, MONTEVIDEO,
Tel. (02)70-4044, Fax. (02)92 0601
For all other countries apply to: Philips Semiconductors,
International Marketing and Sales, Building BAF-1,
P.O. Box 218, 5600 MD, EINDHOVEN, The Netherlands,
Telex 35000 phtcnl, Fax. +31-40-724825
SCD28
© Philips Electronics N.V. 1994
All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation
or contract, is believed to be accurate and reliable and may be changed without
notice. No liability will be accepted by the publisher for any consequence of its
use. Publication thereof does not convey nor imply any license under patent- or
other industrial or intellectual property rights.