STB60N55F3, STD60N55F3, STF60N55F3 STI60N55F3, STP60N55F3, STU60N55F3 N-channel 55 V, 6.5 mΩ, 80 A, DPAK, IPAK, D2PAK, I2PAK, TO-220 TO-220FP STripFET™ III Power MOSFET Features Type VDSS RDS(on) ID Pw STB60N55F3 55V <8.5mΩ 80A 110W STD60N55F3 55V <8.5mΩ 80A 110W STF60N55F3 55V <8.5mΩ 42A 30W STI60N55F3 55V <8.5mΩ 80A 110W STP60N55F3 55V <8.5mΩ 80A 110W STU60N55F3 55V <8.5mΩ 80A 110W 3 3 1 3 2 1 1 2 DPAK IPAK TO-220FP 3 3 12 1 3 ■ Standard threshold drive ■ 100% avalanche tested I²PAK D²PAK 1 2 TO-220 Application ■ Figure 1. Switching applications Internal schematic diagram Description This STripFET™ III Power MOSFET technology is among the latest improvements, which have been especially tailored to minimize on-state resistance providing superior switching performances. Table 1. Device summary Order codes Marking Package Packaging STB60N55F3 60N55F3 D²PAK Tape and reel STD60N55F3 60N55F3 DPAK Tape and reel STF60N55F3 60N55F3 TO-220FP Tube STI60N55F3 60N55F3 I²PAK Tube STP60N55F3 60N55F3 TO-220 Tube STU60N55F3 60N55F3 IPAK Tube April 2009 Doc ID 13242 Rev 4 1/20 www.st.com 20 Contents STx60N55F3 Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Test circuits 4 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 2/20 .............................................. 9 Doc ID 13242 Rev 4 STx60N55F3 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol DPAK/D²PAK Parameter Unit TO-220 TO-220FP IPAK/I²PAK VDS Drain-source voltage (VGS=0) VGS Gate-source voltage 55 V ± 20 V ID Drain current (continuous) at TC = 25°C 80 42 A ID Drain current (continuous) at TC = 100°C 56 30 A IDM (1) Drain current (pulsed) 320 168 A PTOT Total dissipation at TC = 25°C 110 30 W Derating factor 0.73 0.2 W/°C dv/dt (2) Peak diode recovery voltage slope 11 V/ns EAS (3) Single pulse avalanche energy 390 mJ VISO Tj Tstg Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1s;TC=25°C) 2500 Operating junction temperature Storage temperature -55 to 175 V °C 1. Pulse width limited by safe operating area 2. ISD < 80 A, di/dt < 300A/µs, VDD < V(BR)DSS. Tj < Tjmax 3. Starting Tj=25°C, Id=32 A, Vdd= 25 V Table 3. Thermal resistance Value Symbol Parameter DPAK Rthj-case IPAK I²PAK Thermal resistance junctioncase max Thermal resistance junctionRthj-pcb (1) pcb max Unit D²PAK TO-220 TO-220FP 1.36 50 5 35 °C/W °C/W Rthj-a Thermal resistance junctionambient max 100 62.5 °C/W Tl Maximum lead temperature for soldering purpose 275 300 °C 1. When mounted on FR-4 board of 1inch², 2oz Cu Doc ID 13242 Rev 4 3/20 Electrical characteristics 2 STx60N55F3 Electrical characteristics (TCASE= 25 °C unless otherwise specified) Table 4. Symbol V(BR)DSS Static Parameter Test conditions Drain-source breakdown voltage ID = 250µA, VGS= 0 Min. Typ. Max. Unit 55 V VDS = Max rating, VDS = Max rating,Tc = 125°C 10 100 µA µA Gate body leakage current (VDS = 0) VGS = ±20V ±200 nA VGS(th) Gate threshold voltage VDS= VGS, ID = 250µA 4 V RDS(on) Static drain-source on resistance VGS= 10V, ID= 32A 8.5 mΩ IDSS Zero gate voltage drain current (VGS = 0) IGSS Table 5. Symbol gfs (1) Ciss Coss Crss Qg Qgs Qgd 2 6.5 Dynamic Parameter Test conditions Min. Typ. Max. Unit Forward transconductance VDS =25V, ID=32A - 50 S Input capacitance Output capacitance Reverse transfer capacitance VDS = 25V, f = 1MHz, VGS=0 - 2200 500 25 pF pF pF - 33.5 12.5 9.5 Total gate charge Gate-source charge Gate-drain charge VDD = 27V, ID = 65A VGS =10V (see Figure 16) 45 nC nC nC 1. Pulsed: pulse duration = 300 µs, duty cycle 1.5% Table 6. Symbol td(on) tr td(off) tf 4/20 Switching on/off (inductive load) Parameter Turn-on delay time Rise time Turn-off delay time Fall time Test conditions Min. VDD = 27V, ID = 32A, RG = 4.7Ω, VGS = 10V - 20 50 - ns ns - 35 11.5 - ns ns (see Figure 18) VDD = 27V, ID = 32A, RG = 4.7Ω, VGS = 10V (see Figure 18) Doc ID 13242 Rev 4 Typ. Max. Unit STx60N55F3 Table 7. Symbol ISD ISDM (1) ISD ISDM (1) VSD trr Qrr IRRM Electrical characteristics Source drain diode Parameter Test conditions Packages Min. Typ. Max. Unit 2 Source-drain current Source-drain current (pulsed) DPAK-D PAKI2PAK-I2PAKTO-220 - 80 320 A A Source-drain current Source-drain current (pulsed) TO-220FP - 42 168 A A - 1.5 V Forward on voltage Reverse recovery time Reverse recovery charge Reverse recovery current ISD = 65A, VGS = 0 ISD = 65A, VDD = 30V di/dt = 100A/µs, Tj = 150°C (see Figure 17) - 47 87 3.7 ns nC A 1. Pulsed: pulse duration = 300 µs, duty cycle 1.5% Doc ID 13242 Rev 4 5/20 Electrical characteristics STx60N55F3 2.1 Electrical characteristics (curves) Figure 2. Safe operating area for TO-220 D²PAK / IPAK / I²PAK / DPAK Figure 3. Thermal impedance for TO-220 D²PAK / IPAK / I²PAK / DPAK Figure 4. Safe operating area for TO-220FP Figure 5. Thermal impedance for TO-220FP 6/20 Doc ID 13242 Rev 4 STx60N55F3 Electrical characteristics Figure 6. Output characteristics Figure 7. Transfer characteristics Figure 8. Normalized BVDSS vs temperature Figure 9. Static drain-source on resistance Figure 10. Gate charge vs gate-source voltage Figure 11. Capacitance variations Doc ID 13242 Rev 4 7/20 Electrical characteristics STx60N55F3 Figure 12. Normalized gate threshold voltage vs temperature Figure 13. Normalized on resistance vs temperature Figure 14. Source-drain diode forward characteristics 8/20 Doc ID 13242 Rev 4 STx60N55F3 3 Test circuits Test circuits Figure 15. Switching times test circuit for resistive load Figure 16. Gate charge test circuit Figure 17. Test circuit for inductive load Figure 18. Unclamped inductive load test switching and diode recovery times circuit Figure 19. Unclamped inductive waveform Figure 20. Switching time waveform Doc ID 13242 Rev 4 9/20 Package mechanical data 4 STx60N55F3 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK is an ST trademark. 10/20 Doc ID 13242 Rev 4 STx60N55F3 Package mechanical data I²PAK (TO-262) mechanical data mm inch Dim Min A A1 b b1 c c2 D e e1 E L L1 L2 Typ 4.40 2.40 0.61 1.14 0.49 1.23 8.95 2.40 4.95 10 13 3.50 1.27 Doc ID 13242 Rev 4 Max Min 4.60 2.72 0.88 1.70 0.70 1.32 9.35 2.70 5.15 10.40 14 3.93 1.40 0.173 0.094 0.024 0.044 0.019 0.048 0.352 0.094 0.194 0.393 0.511 0.137 0.050 Typ Max 0.181 0.107 0.034 0.066 0.027 0.052 0.368 0.106 0.202 0.410 0.551 0.154 0.055 11/20 Package mechanical data STx60N55F3 D²PAK (TO-263) mechanical data mm inch Dim Min A A1 b b2 c c2 D D1 E E1 e e1 H J1 L L1 L2 R V2 Typ 4.40 0.03 0.70 1.14 0.45 1.23 8.95 7.50 10 8.50 Max Min 4.60 0.23 0.93 1.70 0.60 1.36 9.35 0.173 0.001 0.027 0.045 0.017 0.048 0.352 0.295 0.394 0.334 10.40 2.54 4.88 15 2.49 2.29 1.27 1.30 Max 0.181 0.009 0.037 0.067 0.024 0.053 0.368 0.409 0.1 5.28 15.85 2.69 2.79 1.40 1.75 0.192 0.590 0.099 0.090 0.05 0.051 8° 0° 0.4 0° 0079457_M 12/20 Typ Doc ID 13242 Rev 4 0.208 0.624 0.106 0.110 0.055 0.069 0.016 8° STx60N55F3 Package mechanical data TO-252 (DPAK) mechanical data DIM. mm. min. typ max. A 2.20 2.40 A1 0.90 1.10 A2 0.03 0.23 b 0.64 0.90 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 D1 E 5.10 6.40 6.60 E1 4.70 e 2.28 e1 4.40 4.60 H 9.35 10.10 L 1 L1 2.80 L2 L4 0.80 0.60 1 R V2 0.20 8o 0o 0068772_G Doc ID 13242 Rev 4 13/20 Package mechanical data STx60N55F3 TO-251 (IPAK) mechanical data mm. DIM. min. typ max. A 2.20 2.40 A1 0.90 1.10 b 0.64 0.90 b2 0.95 b4 5.20 5.40 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 E 6.40 6.60 e e1 2.28 4.40 4.60 H 16.10 L 9.00 9.40 (L1) 0.80 1.20 L2 0.80 V1 10 o 0068771_H 14/20 Doc ID 13242 Rev 4 STx60N55F3 Package mechanical data TO-220 mechanical data mm inch Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 ∅P Q Typ 4.40 0.61 1.14 0.48 15.25 Max Min 4.60 0.88 1.70 0.70 15.75 0.173 0.024 0.044 0.019 0.6 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 Doc ID 13242 Rev 4 Max 0.181 0.034 0.066 0.027 0.62 0.050 16.40 28.90 3.75 2.65 Typ 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 3.85 2.95 0.147 0.104 0.151 0.116 15/20 Package mechanical data STx60N55F3 TO-220FP mechanical data mm Dim. Min. Typ. Max. A 4.4 4.6 B 2.5 2.7 D 2.5 2.75 E 0.45 0.7 F 0.75 1 F1 1.15 1.70 F2 1.15 1.5 G 4.95 5.2 G1 2.4 2.7 H 10 10.4 L2 16 L3 28.6 30.6 L4 9.8 10.6 L5 2.9 3.6 L6 15.9 16.4 L7 9 9.3 Dia 3 3.2 L7 E A B D Dia L5 L6 F1 F2 F G H G1 L4 L2 L3 7012510_Rev_J 16/20 Doc ID 13242 Rev 4 STx60N55F3 5 Packaging mechanical data Packaging mechanical data DPAK FOOTPRINT All dimensions are in millimeters TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B DIM. mm inch MIN. MAX. A0 6.8 7 0.267 0.275 B0 10.4 10.6 0.409 0.417 B1 MIN. MIN. 330 1.5 C 12.8 D 20.2 G 16.4 N 50 T TAPE MECHANICAL DATA inch MAX. MAX. 12.992 0.059 13.2 0.504 0.520 18.4 0.645 0.724 0.795 1.968 22.4 0.881 BASE QTY BULK QTY 2500 2500 MAX. 12.1 0.476 1.6 0.059 0.063 D 1.5 D1 1.5 E 1.65 1.85 F 7.4 7.6 0.291 0.299 K0 2.55 2.75 0.100 0.108 0.059 0.065 0.073 P0 3.9 4.1 0.153 0.161 P1 7.9 8.1 0.311 0.319 P2 1.9 2.1 R 40 W 15.7 0.075 0.082 1.574 16.3 0.618 0.641 Doc ID 13242 Rev 4 17/20 Packaging mechanical data STx60N55F3 D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm inch MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 MAX. B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.468 0.476 P2 1.9 2.1 0.075 0.082 R 50 1.574 T 0.25 0.35 0.0098 0.0137 W 23.7 24.3 0.933 0.956 * on sales type 18/20 Doc ID 13242 Rev 4 inch MAX. MIN. MAX. 330 12.992 13.2 0.504 0.520 26.4 0.960 1.039 0.059 0795 3.937 30.4 1.197 BASE QTY BULK QTY 1000 1000 STx60N55F3 6 Revision history Revision history Table 8. Document revision history Date Revision Changes 09-Feb-2007 1 First release 22-Feb-2007 2 Description has been updated 07-Mar-2007 3 The Figure 2, Figure 4, Figure 9 have been changed 17-Apr-2009 4 Added device in I2PAK Updated all mechanical data Doc ID 13242 Rev 4 19/20 STx60N55F3 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2009 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 20/20 Doc ID 13242 Rev 4