TC1269 300mA CMOS LDO with Shutdown and VREF Bypass Features General Description • • • • • • • • • The TC1269 is a fixed output, high accuracy (typically ±0.5%) CMOS upgrade for older (bipolar) low dropout regulators. Total supply current is typically 50µA at full load (20 to 60 times lower than in bipolar regulators). Very Low Ground Current for Longer Battery Life Very Low Dropout Voltage 300mA Output Circuit High Output Voltage Accuracy Standard or Custom Output Voltages Power Saving Shutdown Mode Bypass Input for Ultra Quiet Operation Over Current and Over Temperature Protection Space-Saving MSOP Package The TC1269 incorporates both over temperature and over current protection. The TC1269 is stable with an output capacitor of only 1µF and has a maximum output current of 300mA. Applications • • • • • • • • TC1269 key features include ultra low noise operation (plus optional Bypass input); very low dropout voltage (typically 240mV at full load), and fast response to step changes in load. Supply current is reduced to 0.05µA (typical) and VOUT falls to zero when the shutdown input is low. Battery Operated Systems Portable Computers Medical Instruments Instrumentation Cellular/GSM/PHS Phones Linear Post-Regulator for SMPS Pagers Digital Cameras Typical Application VOUT 1 + C1 1µF 2 VOUT NC VIN SHDN 8 7 Shutdown Control (from Power Control Logic) TC1269 Device Selection Table 3 Part Number Output* Voltage (V) TC1269-2.5VUA 2.5 8-Pin MSOP -40°C to +125°C TC1269-2.8VUA 2.8 8-Pin MSOP -40°C to +125°C TC1269-3.0VUA 3.0 8-Pin MSOP -40°C to +125°C TC1269-3.3VUA 3.3 8-Pin MSOP -40°C to +125°C TC1269-5.0VUA 5.0 8-Pin MSOP -40°C to +125°C Junction Temp. Range Package NC 4 GND NC Bypass VIN 6 CBYPASS 470pF (Optional) *Other output voltages are available. Please contact Microchip Technology Inc. for details. Package Type 8-Pin MSOP VOUT 1 8 VIN NC NC GND 2 7 SHDN NC Bypass 3 TC1269 4 2002 Microchip Technology Inc. 6 5 DS21380B-page 1 TC1269 1.0 ELECTRICAL CHARACTERISTICS *Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings* Input Voltage .........................................................6.5V Output Voltage.................... (VSS – 0.3) to (VIN + 0.3V) Maximum Voltage on Any Pin ........ VIN +0.3V to -0.3V Power Dissipation................Internally Limited (Note 6) Operating Temperature ............... -40°C < TJ < +125°C Storage Temperature.......................... -65°C to +150°C TC1269 ELECTRICAL SPECIFICATIONS Electrical Characteristics: VIN = VOUT + 1V, IL = 0.1µA, CL = 3.3µF, SHDN > VIH, TA = 25°C, unless otherwise noted. Boldface type specifications apply for junction temperatures of -40°C to +125°C. Symbol Parameter VIN Input Operating Voltage IOUTMAX Maximum Output Current VOUT Output Voltage Min Typ Max — — 6.0 V 300 — — mA — — VR ±0.5% VR – 2.5% — VR + 2.5% Units V Test Conditions Note 1 ∆V OUT/∆T VOUT Temperature Coefficient — 40 — ∆VOUT/∆VIN Line Regulation — 0.05 0.35 ∆VOUT/VOUT Load Regulation — 0.5 VIN -VOUT Dropout Voltage — — — 20 80 240 ISS1 Supply Current — 50 90 µA SHDN = VIH ISS2 Shutdown Supply Current — 0.05 0.5 µA SHDN = 0V PSRR Power Supply Rejection Ratio — 50 — dB FRE ≤ 120Hz IOUTSC Output Short Circuit Current — 550 650 mA VOUT = 0V V/W Note 5 ppm/°C Note 2 % (VR + 1V) ≤ VIN ≤ 6V 2.0 % IL = 0.1mA to IOUT MAX 30 160 480 mV IL = 0.1mA IL = 100mA IL = 300mA (Note 4) ∆V OUT/∆PD Thermal Regulation — 0.04 — eN Output Noise — 260 — VIH SHDN Input High Threshold 45 — — %VIN VIL SHDN Input Low Threshold — — 15 %VIN nV/√Hz F = 1kHz, C OUT = 1µF, R LOAD = 50Ω SHDN Input Note 1: 2: 3: 4: 5: 6: VR is the regulator output voltage setting. TC VOUT = (VOUTMAX – VOUTMIN) x 106 VOUT x ∆T Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested over a load range from 0.1mA to the maximum specified output current. Changes in output voltage due to heating effects are covered by the thermal regulation specification. Dropout voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at a 1V differential. Thermal Regulation is defined as the change in output voltage at a time T after a change in power dissipation is applied, excluding load or line regulation effects. Specifications are for a current pulse equal to ILMAX at VIN = 6V for T = 10 msec. The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction temperature and the thermal resistance from junction-to-air (i.e., TA, TJ, θJA). Exceeding the maximum allowable power dissipation causes the device to initiate thermal shutdown. Please see Section 4.0 Thermal Considerations for more details. DS21380B-page 2 2002 Microchip Technology Inc. TC1269 2.0 PIN DESCRIPTIONS The descriptions of the pins are listed in Table 2-1. TABLE 2-1: PIN FUNCTION TABLE Pin No. (8-Pin SOIC) Symbol 1 VOUT 2 NC No connect. 3 NC No connect. 4 GND 5 Bypass 6 NC 7 SHDN 8 VIN 2002 Microchip Technology Inc. Description Regulated voltage output. Ground terminal. Reference bypass input. Connecting a 470pF to this input further reduces output noise. No connect. Shutdown control input. The regulator is fully enabled when a logic high is applied to this input. The regulator is fully enabled when a logic high is applied to this input. The regulator enters shutdown when a logic low is applied to this input. During shutdown, output voltage falls to zero and supply current is reduced to 0.05µA (typical). Unregulated supply input. DS21380B-page 3 TC1269 3.0 DETAILED DESCRIPTION 3.1 Bypass Input The TC1269 is a precision regulator available in fixed voltages. Unlike the bipolar regulators, the TC1269 supply current does not increase with load current. In addition, VOUT remains stable and within regulation over the entire 0mA to IOUTMAX operating load current range, (an important consideration in RTC and CMOS RAM battery backup applications). A 470pF capacitor connected from the Bypass input to ground reduces noise present on the internal reference, which in turn significantly reduces output noise. If output noise is not a concern, this input may be left unconnected. Larger capacitor values may be used, but results in a longer time period to rated output voltage when power is initially applied. Figure 3-1 shows a typical application circuit. The regulator is enabled any time the shutdown input (SHDN) is at or above VIH, and shutdown (disabled) when SHDN is at or below VIL. SHDN may be controlled by a CMOS logic gate, or I/O port of a microcontroller. If the SHDN input is not required, it should be connected directly to the input supply. While in shutdown, supply current decreases to 0.05µA (typical), VOUT falls to zero. 3.2 FIGURE 3-1: VOUT 1 + C1 1µF 2 TYPICAL APPLICATION CIRCUIT VOUT VIN SHDN NC 8 + 7 NC 4 GND DS21380B-page 4 NC Bypass Battery Shutdown Control (from Power Control Logic) TC1269 3 C1 1µF + – Output Capacitor A 1µF (min) capacitor from VOUT to ground is recommended. The output capacitor should have an effective series resistance greater than 0.1Ω and less than 5.0Ω, and a resonant frequency above 1MHz. A 1µF capacitor should be connected from VIN to GND if there is more than 10 inches of wire between the regulator and the AC filter capacitor, or if a battery is used as the power source. Aluminum electrolytic or tantalum capacitor types can be used. (Since many aluminum electrolytic capacitors freeze at approximately -30°C, solid tantalums are recommended for applications operating below -25°C.) When operating from sources other than batteries, supply-noise rejection and transient response can be improved by increasing the value of the input and output capacitors and employing passive filtering techniques. 6 CBYPASS 470pF (Optional) 2002 Microchip Technology Inc. TC1269 4.0 THERMAL CONSIDERATIONS 4.1 Thermal Shutdown Integrated thermal protection circuitry shuts the regulator off when die temperature exceeds 150°C. The regulator remains off until the die temperature drops to approximately 140°C. 4.2 Equation 4-1 can be used in conjunction with Equation 4-2 to ensure regulator thermal operation is within limits. For example: Given: VINMAX VOUTMIN = 2.7V – 2.5% Power Dissipation The amount of power the regulator dissipates is primarily a function of input and output voltage, and output current. The following equation is used to calculate worst case actual power dissipation: EQUATION 4-1: PD ≈ (VINMAX – VOUTMIN)ILOAD MAX Where: PD VINMAX VOUTMIN ILOADMAX EQUATION 4-2: PDMAX = (TJMAX – TAMAX) θJA Where all terms are previously defined. 2002 Microchip Technology Inc. ILOAD = 250mA TAMAX = 55°C Find: 1. Actual power dissipation 2. Maximum allowable dissipation Actual power dissipation: PD ≈ (VINMAX – VOUTMIN) ILOADMAX = [(3.0 x 1.1) – (2.7 x .975)]250 x 10-3 = 167mW Maximum allowable power dissipation: PDMAX = (TJMAX – TAMAX) θJA = Worst case actual power dissipation = Maximum voltage on VIN = Minimum regulator output voltage = Maximum output (load) current The maximum allowable power dissipation (Equation 4-2) is a function of the maximum ambient temperature (TAMAX), the maximum allowable die temperature (TJMAX) and the thermal resistance from junction-to-air (θJA). = 3.0V ± 10% = (125 – 55) 200 = 350mW In this example, the TC1269 dissipates a maximum of 167mW; below the allowable limit of 350mW. In a similar manner, Equation 4-1 and Equation 4-2 can be used to calculate maximum current and/or input voltage limits. 4.3 Layout Considerations The primary path of heat conduction out of the package is via the package leads. Therefore, layouts having a ground plane, wide traces at the pads, and wide power supply bus lines combine to lower θJA and, therefore, increase the maximum allowable power dissipation limit. DS21380B-page 5 TC1269 5.0 TYPICAL CHARACTERISTICS Note: The graphs and tables provided following this note are a statistical summary based on a limited number of samples and are provided for informational purposes only. The performance characteristics listed herein are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified operating range (e.g., outside specified power supply range) and therefore outside the warranted range. 2.00 10.0 RLOAD = 50Ω COUT = 1µF 0.006 0.004 0.002 1.80 LOAD REGULATION (%) NOISE (µV/√HZ) LINE REGULATION (%) 0.010 0.008 Load Regulation Output Noise Line Regulation 0.012 1.0 0.1 0.000 -0.002 1.40 1 to 300mA 1.20 1.00 0.80 0.60 1 to 100mA 0.40 1 to 50mA 0.20 0.0 0.01 -0.004 -40° -20° 0° 20° 40° 60° 80° 100° 120° 0.01 TEMPERATURE (°C) 10 1 Supply Current 60.0 50.0 VOUT vs. Temperature 3.075 85°C C 0.30 70°C 0.25 VIN = 4V ILOAD = 100µA CLOAD = 3.3µF 3.025 VOUT (V) DROPOUT VOLTAGE (V) 70.0 TEMPERATURE (°C) 125°C 0.35 80.0 0.00 -40° -20° 0° 20° 40° 60° 80° 100° 120° 1000 Dropout Voltage vs. Load Current 0.40 90.0 100 FREQUENCY (kHz) 100.0 SUPPLY CURRENT (µA) 1.60 25°C 0.20 0°C C 0.15 2.975 0.10 -40°C 0.05 40.0 -40° -20° 0° 20° 40° 60° 80° 100° 120° TEMPERATURE (°C) DS21380B-page 6 0.00 0 50 100 150 200 LOAD CURRENT (mA) 250 300 2.925 -40° -20° 0° 20° 40° 60° 80° 100° 120° TEMPERATURE (°C) 2002 Microchip Technology Inc. TC1269 6.0 PACKAGING INFORMATION 6.1 Package Marking Information Package marking data not available at this time. 6.2 Taping Form Component Taping Orientation for 8-Pin MSOP Devices User Direction of Feed PIN 1 W P Standard Reel Component Orientation for TR Suffix Device Carrier Tape, Number of Components Per Reel and Reel Size Package 8-Pin MSOP 6.3 Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size 12 mm 8 mm 2500 13 in Package Dimensions 8-Pin MSOP PIN 1 .122 (3.10) .114 (2.90) .197 (5.00) .189 (4.80) .026 (0.65) TYP. .122 (3.10) .114 (2.90) .043 (1.10) MAX. .016 (0.40) .010 (0.25) .006 (0.15) .002 (0.05) .008 (0.20) .005 (0.13) 6° MAX. .028 (0.70) .016 (0.40) Dimensions: inches (mm) 2002 Microchip Technology Inc. DS21380B-page 7 TC1269 NOTES: DS21380B-page 8 2002 Microchip Technology Inc. TC1269 SALES AND SUPPORT Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 792-7277 The Microchip Worldwide Site (www.microchip.com) Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products. 2002 Microchip Technology Inc. DS21380B-page 9 TC1269 NOTES: DS21380B-page 10 2002 Microchip Technology Inc. TC1269 Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, FilterLab, KEELOQ, microID, MPLAB, PIC, PICmicro, PICMASTER, PICSTART, PRO MATE, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. dsPIC, ECONOMONITOR, FanSense, FlexROM, fuzzyLAB, In-Circuit Serial Programming, ICSP, ICEPIC, microPort, Migratable Memory, MPASM, MPLIB, MPLINK, MPSIM, MXDEV, MXLAB, PICC, PICDEM, PICDEM.net, rfPIC, Select Mode and Total Endurance are trademarks of Microchip Technology Incorporated in the U.S.A. Serialized Quick Turn Programming (SQTP) is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. © 2002, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999 and Mountain View, California in March 2002. The Company’s quality system processes and procedures are QS-9000 compliant for its PICmicro ® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs, microperipherals, non-volatile memory and analog products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified. 2002 Microchip Technology Inc. DS21380B-page 11 WORLDWIDE SALES AND SERVICE AMERICAS ASIA/PACIFIC Japan Corporate Office Australia 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: 480-792-7627 Web Address: http://www.microchip.com Microchip Technology Australia Pty Ltd Suite 22, 41 Rawson Street Epping 2121, NSW Australia Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 Microchip Technology Japan K.K. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Rocky Mountain China - Beijing 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7966 Fax: 480-792-7456 Microchip Technology Consulting (Shanghai) Co., Ltd., Beijing Liaison Office Unit 915 Bei Hai Wan Tai Bldg. No. 6 Chaoyangmen Beidajie Beijing, 100027, No. China Tel: 86-10-85282100 Fax: 86-10-85282104 Atlanta 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Boston 2 Lan Drive, Suite 120 Westford, MA 01886 Tel: 978-692-3848 Fax: 978-692-3821 Chicago 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Detroit Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Kokomo 2767 S. Albright Road Kokomo, Indiana 46902 Tel: 765-864-8360 Fax: 765-864-8387 Los Angeles 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 China - Chengdu Microchip Technology Consulting (Shanghai) Co., Ltd., Chengdu Liaison Office Rm. 2401, 24th Floor, Ming Xing Financial Tower No. 88 TIDU Street Chengdu 610016, China Tel: 86-28-86766200 Fax: 86-28-86766599 China - Fuzhou Microchip Technology Consulting (Shanghai) Co., Ltd., Fuzhou Liaison Office Unit 28F, World Trade Plaza No. 71 Wusi Road Fuzhou 350001, China Tel: 86-591-7503506 Fax: 86-591-7503521 China - Shanghai Microchip Technology Consulting (Shanghai) Co., Ltd. Room 701, Bldg. B Far East International Plaza No. 317 Xian Xia Road Shanghai, 200051 Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 China - Shenzhen 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 Microchip Technology Consulting (Shanghai) Co., Ltd., Shenzhen Liaison Office Rm. 1315, 13/F, Shenzhen Kerry Centre, Renminnan Lu Shenzhen 518001, China Tel: 86-755-2350361 Fax: 86-755-2366086 San Jose China - Hong Kong SAR Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 Microchip Technology Hongkong Ltd. Unit 901-6, Tower 2, Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 New York Toronto 6285 Northam Drive, Suite 108 Mississauga, Ontario L4V 1X5, Canada Tel: 905-673-0699 Fax: 905-673-6509 India Microchip Technology Inc. India Liaison Office Divyasree Chambers 1 Floor, Wing A (A3/A4) No. 11, O’Shaugnessey Road Bangalore, 560 025, India Tel: 91-80-2290061 Fax: 91-80-2290062 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea 135-882 Tel: 82-2-554-7200 Fax: 82-2-558-5934 Singapore Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-6334-8870 Fax: 65-6334-8850 Taiwan Microchip Technology Taiwan 11F-3, No. 207 Tung Hua North Road Taipei, 105, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE Denmark Microchip Technology Nordic ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 France Microchip Technology SARL Parc d’Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Germany Microchip Technology GmbH Gustav-Heinemann Ring 125 D-81739 Munich, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Italy Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 United Kingdom Microchip Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5869 Fax: 44-118 921-5820 05/01/02 *DS21380* DS21380B-page 12 2002 Microchip Technology Inc.