TDA7461N ® CAR RADIO SIGNAL PROCESSOR HIGH PERFORMANCE SIGNAL PROCESSOR FOR CAR RADIO SYSTEMS DEVICE INCLUDES AUDIO PROCESSOR, STEREO DECODER, NOISEBLANKER AND MULTIPATH DETECTOR NO EXTERNAL COMPONENTS REQUIRED FULLY PROGRAMMABLE VIA I2C BUS LOW DISTORTION LOW NOISE SO28 DIP28 ORDERING NUMBERS: TDA7461ND DESCRIPTION The TDA7461N is a high performance signal processor specifically designed for car radio applications. The device includes a complete audioprocessor and a stereo decoder with noiseblanker, stereoblend and all signal processing functions necessary for state-of-the-art as well as future car radio systems. Switched-capacitors design technique allows to obtain all these features without external compo- TDA7461N nents or adjustments. This means that higher quality and reliability walks alongside an overall cost saving. The CSP is fully programmable by I2C bus interface allowing to customize key device parameters and especially filter characteristics. The BICMOS process combined with the optimized signal processing assure low noise and low distortion performances. AM CASS R CASS L PHONE PH GND 10 17 MIXING STAGE LOUDNESS 28 SOFT MUTE VOLUME TREBLE ACINR SMUTE CDR 5 ACINL CDG 6 ACOUTR CDL 7 ACOUTL BLOCK DIAGRAM 27 1 2 OUT LF BASS OUT RR 3 4 9 OUT LR OUT RF INPUT MULTIPLEXER + AUTO ZERO PHONE 23 25 22 24 18 BEEP I2C BUS DIGITAL CONTROL 8 19 16 15 MPX VS 11 21 PILOT CANCELLATION 80KHz LP SUPPLY 20 GND October 2003 PLL 26 CREF DEMODULATOR + STEREO ADJUST + STEREO BLEND 25KHz LP S&H OUT LR OUT LF OUT RR OUT RF SCL SDA MUX R MUX L HIGH CUT CONTROL D PIL DET MULTIPATHDETECTOR 13 MPIN NOISE BLANKER 14 MPOUT PULSE FORMER A 12 LEVEL D97AU646A 1/32 TDA7461N ABSOLUTE MAXIMUM RATINGS Symbol VS Tamb Tstg Parameter Value Operating Supply Voltage Unit 10.5 V Operating Ambient Temperature Range -40 to 85 °C Storage Temperature Range -55 to 150 °C SUPPLY Symbol VS IS SVRR Parameter Test Condition Min. Typ. Max. Unit 7.5 9 10 V 25 30 35 mA Supply Voltage Supply Current VS = 9V Ripple Rejection @ 1KHz Audioprocessor (all filters flat) 60 dB Stereodecoder + Audioprocessor 45 dB ESD All pins are protected against ESD according to the MIL883 standard. PIN CONNECTION ACINL 1 28 ACOUTL ACINR 2 27 ACOUTR CASSR 3 26 CREF CASSL 4 25 OUTLF CDR 5 24 OUTRF CDGND 6 23 OUTLR CDL 7 22 OUTRR PH GND 8 21 VS PHONE 9 20 GND AM 10 19 SDA MPX 11 18 SCL LEVEL 12 17 SMUTE MPIN 13 16 MUXR MPOUT 14 15 MUXL D97AU647 THERMAL DATA Symbol Rth-j pins 2/32 Parameter Thermal Resistance Junction-pins Max DIP28 SO28 Unit 65 85 °C/W TDA7461N PIN DESCRIPTION N. Name 1 ACINL Speaker Stage Input Left Function Type I 2 ACINR Speaker Stage Input Right I 3 CASSR Cassette Input Right I 4 CASSL Cassette Input Left I 5 CDR CD Right Channel Input I 6 CDGND Ground reference CD I 7 CDL CD Left Channel Input I 8 PHGND Phone Ground I 9 PHONE 10 AM 11 MPX 12 LEVEL 13 MPIN 14 MPOUT Multipath Detector Output O 15 MUXL Multiplexer Output Left Channel (Stereodecoder Output left selectable 1) O 16 MUXR Multiplexer Output Right Channel (Stereodecoder Output right selectable 1) O 17 SMUTE Soft Mute Drive I 18 SCL Phone Input I AM Input I FM Input (MPX) I Level Input Stereodecoder I Multipath Detector Input I 2 I/O 2 I/O I C Clock Line 19 SDA I C Data Line 20 GND Supply Ground S 21 VS Supply Voltage S 22 OUTRR Right Rear Speaker Output O 23 OUTLR Left Rear Speaker Output O 24 OUTRF Right Front Spaeaker Output O 25 OUTLF Left Front Speaker Output O 26 CREF Reference Capacitor Pin S 27 ACOUTR Pre-speaker AC Output Right Channel O 28 ACOUTL Pre-speaker AC Output Left Channel O (1) See databyte specification - speaker attenuators Pin type legenda: I = Input O = Output I/O = Input/Output S = Supply 3/32 TDA7461N AUDIO PROCESSOR PART Input Multiplexer Fully differential or quasi-differential CD and cassette stereo input AM mono or stereo input Phone differential or single ended input Internal beep with 2 frequencies (selectable) Mixable phone and beep signals Bass Control 2nd order frequency response Center frequency programmable in 4(5) steps DC gain programmable 7 x 2dB steps Treble Control 2nd order frequency response Center frequency programmable in 4 steps 7 x 2dB steps Loudness Second order frequency response Programmable center frequency and quality factor 15 x 1dB steps Selectable flat-mode (constant attenuation) Speaker Control 4 independent speaker controls (1dB steps control range 50dB) Volume control 1dB attenuator Max. gain 20dB Max. attenuation 79dB Soft-step gain control Mute Functions Direct mute Digitally controlled softmute with 4 programmable time constants ELECTRICAL CHARACTERISTICS (VS = 9V; Tamb = 25°C; RL = 10KΩ; all gains = 0dB; f = 1KHz; unless otherwise specified). Symbol Parameter Test Condition Min. Typ. Max. Unit 70 100 130 KΩ INPUT SELECTOR Rin Input Resistance VCL Clipping Level 2.2 2.6 SIN Input Separation Min. Input Gain 80 -1 100 0 1 dB dB Max. Input Gain 13 14 15 dB Adjacent Gain Step GMIN to GMAX 1 -5 -5 2 0 1 3 +5 +5 dB mV mV 70 20 45 100 30 70 130 40 Common Mode Rejection Ratio Differential Common Mode VCM = 1VRMS @ 1KHz KΩ KΩ dB VCM = 1VRMS @ 10KHz 20Hz to 20KHz flat; all stages 0dB 45 Output Noise @ Speaker Output 60 9 GIN MIN GIN MAX GSTEP VDC Step Resolution DC Steps all inputs except Phone VRMS DIFFERENTIAL CD STEREO INPUT Rin CMRR eN Input Resistance 15 dB µV DIFFERENTIAL PHONE INPUT Rin CMRR Input Resistance Differential 10 15 20 KΩ 20 30 40 KΩ Common Mode Rejection Ratio Common Mode VCM = 1VRMS @ 1KHz 45 45 70 60 VCM = 1VRMS @ 10KHz 4/32 dB dB TDA7461N ELECTRICAL CHARACTERISTICS (continued) Symbol Parameter Test Condition Min. Typ. Max. Unit BEEP CONTROL VRMS fBMIN Beep Level Lower Beep Frequency 250 570 350 600 500 630 mV Hz fBMAX Higher Beep Frequency 1.15 1.2 1.25 KHz Source -1 0 1 dB Source Source -5 -10 -6 -12 -7 -14 dB dB Beep/Phone -1 0 1 dB MIXING CONTROL MLEVEL Mixing Level VOLUME CONTROL GMAX Max Gain 19 20 21 dB AMAX Max Attenuation -83 -79 -75 dB ASTEP EA Step Resolution Attenuation Set Error G = -20 to 20dB 0.5 -1.25 1 0 1.5 1.25 dB dB G = -60 to 20dB -4 0 3 2 dB dB Adjacent Attenuation Steps From 0dB to GMIN -3 -7 0.1 0.5 3 +7 mV mV 0.5 -16 1 -15 1.5 -14 dB dB ET VDC Tracking Error DC Steps LOUDNESS CONTROL ASTEP AMAX Step Resolution Max. Attenuation fCMIN fCMAX Lower Center Frequency 180 200 220 Hz Higher Center Frequency 360 400 440 Hz 60 100 0.48 0.96 40.4 324 1 2 60 600 dB ms ms ms ms SOFT MUTE AMUTE TD VTHlow VTHhigh RPU VPU Mute Attenuation Delay Time Low Threshold for SM Pin1 High Threshold for SM Pin Internal Pull-up Resistor Pull-up Voltage T1 T2 T3 T4 20 200 1 2.5 70 100 4.7 130 10 15 V V KΩ V SOFT STEP TSW Switch Time 5 ms 1) The SM pin is active low (Mute = 0) 5/32 TDA7461N ELECTRICAL CHARACTERISTICS (continued) Symbol Parameter Test Condition Min. Typ. Max. Unit fC1 fC2 fC3 fC4 Q1 Q2 Q3 Q4 DC = off DC = on ±13 1 54 63 72 90 0.9 1.1 1.3 1.8 -1 4 ±14 2 60 70 80 100(2) 1 1.25 1.5 2 0 4.4 ±15 3 66 77 88 110 1.1 1.4 1.7 2.2 +1 6 dB dB Hz Hz Hz Hz fC1 fC2 fC3 fC4 ±13 1 8 10 12 14 ±14 2 10 12.5 15 17.5 ±15 3 12 15 18 21 dB dB KHz KHz KHz KHz -53 0.5 80 -2 -50 1 90 -47 2 2 5 dB dB dB dB mV 30 3.8 10 100 4.0 VRMS KΩ nF Ω V 3 15 µV 6.5 15 µV BASS CONTROL CRANGE ASTEP fC Control Range Step Resolution Center Frequency QBASS Quality Factor DCGAIN Bass-Dc-Gain dB dB TREBLE CONTROL CRANGE ASTEP fC Control Range Step Resolution Center Frequency SPEAKER ATTENUATORS CRANGE ASTEP AMUTE EE VDC Control Range Step Resolution Output Mute Attenuation Attenuation Set Error DC Steps Adjacent Attenuation Steps 0.1 AUDIO OUTPUTS VCLIP RL CL ROUT VDC Clipping Level Output Load Resistance Output Load Capacitance Output Impedance DC Voltage Level d = 0.3% Output Noise BW = 20 Hz to 20 KHz output muted BW = 20 Hz to 20 KHz all gain = 0dB all gain = 0dB flat; VO = 2VRMS bass treble at 12dB; VO = 2.6VRMS VIN = 1VRMS; all stages 0dB VIN = 1VRMS; Bass & Treble = 12dB 2.2 2 3.6 2.6 GENERAL eNO S/N d SC ET Signal to Noise Ratio Distortion Channel separation Left/Right Total Tracking Error AV = 0 to -20dB AV = -20 to -60dB 2) See description of Audioprocessor Part - Bass & Treble filter characteristics programming 6/32 106 100 80 -1 -2 0.002 0.05 100 0 0 dB dB 0.1 0.1 1 2 % % dB dB dB TDA7461N DESCRIPTION OF THE AUDIOPROCESSOR PART Programmable Input Matrix The programmable input matrix of the TDA7461N offers several possibilities to adapt the audioprocessor to the desired application. In to the standard application we have: CD quasi differential Cassette stereo Phone differential AM mono Stereodecoder input. The input matrix can be configured by only 2 bits: bits 3 and 4 of subaddress 0. Basically the bit of subaddress 13 is fixed by the application and has to be programmed only once at the startup of the IC. For many configurations the two bits are also fixed during one application (e.g. the standard application) and a change of the input source can be done by loading the first three bits of subaddress 0. In other configurations for some sources a programming of bit 3 and 4 of subaddress 0 is necessary in addition to the three source selection bits. In every case only the subaddress 0 has to be changed to switch from one source to another. The following picture shows the input and source programming flow: Figure 1. Input Configuration Tree TDA7461 CD QD CD FD APPL. 1 APPL. 2 APPL. 3 APPL. 4 APPL. 5 APPL. 6 CD QD CASSETTE FM STD AM MONO PHONE (D) CD QD CASSETTE FM STD AM STEREO PHONE (SE) CD QD CASSETTE FM STD AM STD PHONE (D) CD FD CASSETTE FM STD AM MONO PHONE (SE) CD FD CASSETTE FM STD AM STEREO CD FD CASSETTE FM STD AM STD PHONE (SE) D97AU632B Note: in AMSTD configuration the AM mono signal is lead through the FM stereodecoder part to use its additional filters and high-cut function. PIN NUMBER Appl. No 1) 6 1 2 CDGND CDGND 8 PhoneGND PhoneGND 9 Phone AMRIGHT 10 AMMONO AMLEFT 3 CDGND PhoneGND Phone AMSTD 4 5 CDRGND CDRGND CDLGND CDLGND Phone AMRIGHT AMMONO AMLEFT 6 CDRGND CDLGND Phone AMSTD Startup: Startup: FM AM Phone Startup: FM AM Phone Startup: Startup: FM AM Startup: FM AM Phone Programming 1) 0/xxx11xxx 0/xxxx1xxx 0/xxx11100 0/xxx01011 0/xxx11010 0/xxxx1xxx 0/xxx11100 0/xxx01100 0/xxx11010 0/xxxx0xxx 0/xxxx0xxx 0/xxx10100 0/xxx00011 0/xxxx0xxx 0/xxx10100 0/xxx00100 0/xxx10010 Syntax 0/xxx11100 means: SUBADDRESS = 0 - DATA BYTE = xxx11100 (x - don’t care) 7/32 TDA7461N How to find the right input configuration The best way to come to the desired configuration may be to go through the application tree from the top to the bottom while making the specific decisions. This way will lead to one of the six possible applications. Then take the number of the application and go into the pinning table. Here you will find the special pinout as well as the special programming codes for selecting sources. For example in Appl. 6 the TDA7461N has to be configured while startup with the databyte 0/xxxx0xxx. To select the FM, AM or phone source the last five significant bits of subaddress 0 have to be changed, for any other source the last three bits are sufficient (see data byte specification). Input stages Most of the input circuits are the same as in preceeding ST audioprocessors with exception of the CD inputs (see figure 2). In the meantime there are some CD players in the market having a significant high source impedance which affects strongly the commonmode rejection of the normal differential input stage. The additional buffer of the CD input avoids this drawback and offers the full commonmode rejection even with those CD players. The TDA7461N can be configured with an additional input; if the AC coupling before the speaker stage is not used (bit 7 in subaddress 5 set to "1") ACINL and ACINR pins can be used as an additional stereo input. AutoZero In order to reduce the number of pins there is no AC coupling between the In-Gain and the following stage, so that any offset generated by or before the In-Gain stage would be transferred or even amplified to the output. 8/32 To avoid that effect a special offset cancellation stage called AutoZero is implemented. To avoid audible clicks the audioprocessor is muted before the loudness stage during this time. In some cases, for example if the µP is executing a refresh cycle of the I2C bus programming, it is not useful to start a new AutoZero action because no new source is selected and an undesired mute would appear at the outputs. For such applications the TDA7461N could be switched in the "Auto Zero Remain" mode (Bit 6 of the subaddress byte). If this bit is set to high, the DATABYTE 0 could be loaded without invoking the AutoZero and the old adjustment value remains. MUX OUTPUT The MUX_L and MUX_R outputs can provide selectively the output of the input multiplexer (Speaker RF register, Byte 8, bit 6=1) or the output of the stereodecoder (Speaker RF register Byte 8 bit 6=0). If bit D3 byte 10 (Stdec Register) is set to 1, then the stdec signal is automatically muted, when another source is selected at the input multiplexer. If bit D3 byte 10 (Stdec Register) is set to 0, then the stdec signal will be always available at the Mux out pins, no matter which is the selected source. The selection of the stereodecoder input, via a special procedure, is recommended. 1)Soft Mute or Mute the signal path 2)Temporary deselect the stereodec 3) Wait 100-200ms to allow the stdec internal filters to settle 4) Select sterodec input (with automatic autozero) This procedure guarantees an optimum offsetcancellation, avoiding big DC offsets due to the autozero circuitry, which otherwise could try to compensate the signal sourced at the MPX input instead of the stereodecoder intrinsic offset. TDA7461N Figure 2. Input stages 15K 15K CD - 100K + 15K 15K CDGND 15K 15K PHONE + 15K 15K IN GAIN PH_GND CASSETTE 100K AM 100K STEREODECODER MPX 100K D97AU633A Mixing Stage This stage offers the possibility to mix the internal beep or the phone signal to any other source. Due to the fact that the mixing stage is also located behind the In-Gain stage fine adjustments of the main source level can be done in this way. Loudness There are four parameters programmable in the loudness stage (see fig. 3, 4, 5): Figure 3. Loudness Attenuation @ fc = 400Hz (second order) 0.0 -5.0 -10.0 -15.0 - Attenuation - Center Frequency - Loudness Q - Flat Mode: in this mode the loudness stage works as a 0 - 15dB attenuator. Softmute The digitally controlled softmute stage allows muting/demuting the signal with a I2C bus programmable slope. The mute process can either be activated by the softmute pin or by the I2C bus. The slope is realized in a special S shaped curve to mute slow in the critical regions (see figure 6). For timing purposes the Bit 3 of the I2C bus output register is set to 1 from the start of muting until the end of demuting. -20.0 10.0 100.0 1.0K 10.0K Figure 4. Loudness Center frequency @ Attn. = 15dB (second order) 0.0 -5.0 -10.0 -15.0 -20.0 10.0 100.0 1.0K 10.0K 9/32 TDA7461N Figure 5. Loudness @ Attn. = 15dB, fc = 400Hz Figure 6. Softmute Timing D98AU844 (dB) EXT. MUTE 1 -5 +SIGNAL -10 REF -SIGNAL -15 1 -20 10 I2C BUS OUT 100 1,000 Bass There are three parameters programmable in the bass stage (see figs 8, 9, 10, 11): - Attenuation - Center Frequency (60, 70, 80 and 100Hz) - Quality Factors (1, 1.25, 1.5 and 2) Time D97AU634 Hz Softstep Volume When volume level is changed often an audible click appears at the output. The root cause of those clicks could be either a DC offset before the volume stage or the sudden change of the envelope of the audio signal. With the Softstep feature both kinds of clicks could be reduced to a minimum and are no more audible (see figure 7). Note: Please notice that a started Mute action is always terminated and could not be interrupted by a change of the mute signal. Figure 7. Soft Step Timing VOUT 2dB 1dB Time 10ms -1dB -2dB D97AU635 DC Mode In this mode the DC gain is increased by 4.4dB. In addition the programmed center frequency and quality factor is decreased by 25% which can be used to reach alternative center frequencies or quality factors. Treble There are two parameters programmable in the treble stage (see figs 12, 13): - Attenuation - Center Frequency (10, 12.5, 15 and 17.5kHz). Speaker Attenuator Due to practical aspects the steps in the speaker attenuators are not linear over the full range. At attenuations more than 24dB the steps increase from 1.5dB to 10dB (please see data byte specification). 10/32 Note: For steps more than 1dB the softstep mode should be deactivated because it could generate a 1dB error during the blend-time TDA7461N Figure 8. Bass Control @ fc = 80Hz, Q = 1 Figure 9. Bass Center @ Gain = 14dB, Q = 1 15.0 15.0 10.0 12.5 5.0 10.0 7.5 0.0 5.0 -5.0 2.5 -10.0 0.0 -15.0 10.0 100.0 1.0K 10.0K 10.0 100.0 1.0K 10.0K Figure 10. Bass Quality factors @ Gain = 14dB, fc = 80Hz Figure 11. Bass normal and DC Mode @ Gain = 14dB, fc = 80Hz 15.0 15.0 12.5 12.5 10.0 10.0 7.5 7.5 5.0 5.0 2.5 2.5 0.0 10.0 0.0 10.0 100.0 1.0K 10.0K 100.0 1.0K 10.0K Note: In general the center frequency, Q and DC-mode can be set independently. The exception from this rule is the mode (5/xx1111xx) where the center frequency is set to 150Hz instead of 100Hz. Figure 12. Treble Control @ fc = 17.5KHz Figure 13. Treble Center Frequencies @ Gain = 14dB 15.0 15.0 10.0 12.5 5.0 10.0 7.5 0.0 5.0 -5.0 2.5 -10.0 0.0 -15.0 10.0 100.0 1.0K 10.0K 10.0 100.0 1.0K 10.0K 11/32 TDA7461N STEREODECODER PART No external components necessary PLL with adjustment free fully integrated VCO Automatic pilot dependent MONO/STEREO switching Very high suppression of intermodulation and interference Programmable Roll-Off compensation Dedicated RDS Softmute Highcut and Stereoblend characterisctics programmable in a wide range Internal Noiseblanker with threshold controls Multipath detector with programmable internal/external influence I2C bus control of all necessary functions ELECTRICAL CHARACTERISTICS (VS = 9V; deemphasis time constant = 50µs, VMPX = 500mV, 75KHz deviation, f = 1KHz. GI = 6dB, Tamb = 25°C; unless otherwise specified). Symbol VIN Rin Gmin Gmax GSTEP SVRR α THD S+N N Parameter MPX Input Level Input Resistance Minimum Input Gain Max Input Gain Step Resolution Supply Voltage Ripple Rejection Max Channel Separation Total Harmonic Distortion Signal plus Noise to Noise Ratio Test Condition Input Gain = 3.5dB Min. S = 2Vrms 80 Typ. 0.5 100 3.5 11 2.5 55 50 0.02 91 for Stereo, PTH = 1 for Stereo, PTH = 0 for Mono, PTH = 1 for Stereo, PTH = 0 10 15 7 10 15 25 12 19 70 1.5 8.5 1.75 Vripple = 100mv, f = 1khz 30 Max. 1.25 130 4.5 12.5 3.25 25 35 17 25 0.3 Unit VRMS KΩ dB dB dB dB dB % dB MONO/STEREO SWITCH VPTHST1 VPTHST0 VPTHMO1 VPTHMO0 Pilot Threshold Voltage Pilot Threshold Voltage Pilot Threshold Voltage Pilot Threshold Voltage mV mV mV mV PLL ∆f/f Capture Range 0.5 % DEEMPHASIS and HIGHCUT (5) τHC50 Deemphasis Time Constant τHC75 Deemphasis Time Constant τHC50 Highcut Time Constant τHC75 Highcut Time Constant Bit = 7, Subadr. 10 = 0 VLEVEL >> VHCH Bit = 7, Subadr. 10 = 1 VLEVEL >> VHCH Bit = 7, Subadr. 10 = 0 VLEVEL >> VHCL Bit = 7, Subadr. 10 = 1 VLEVEL >> VHCL 25 50 75 µs 50 75 100 µs 100 150 200 µs 150 225 300 µs 4.7 5 3300 0 10 0.67 33 58 8.4 5.3 V ppm dB dB dB %REF5V %REF5V %REF5V STEREOBLEND and HIGHCUT-CONTROL REF5V TCREF5V LGmin LGmax LGstep VSBLmin VSBLmax VSBLstep 12/32 Internal Reference Voltage Temperature Coefficient Min. LEVEL Gain Max. LEVEL Gain LEVEL Gain Step Resolution Min.Voltage for Mono Max. Voltage for Mono Step Resolution -1 8 0.3 29 54 5.0 +1 12 1.0 37 62 12 TDA7461N ELECTRICAL CHARACTERISTICS (continued) Symbol Parameter Test Condition Min. Typ. Max. Unit 36 62 5 13 29 42 66 8.4 17 33 46 70 12 21 37 %REF5V %REF5V %REF5V %VHCH %VHCH 40 50 75 62 90 dB dB dB dB fmod = 10KHz; fspur = 1KHz; fmod = 13KHz; fspur = 1KHz; 65 75 dB dB f = 57KHz 70 dB 75 dB 95 84 dB dB STEREOBLEND and HIGHCUT CONTROL VHCHmin VHCHmax VHCHstep VHCLmin VHCLmax Min.Voltage for NO Highcut Max. Voltage for NO Highcut Step Resolution Min. Voltage for FULL High cut Max. Voltage for FULL High cut Carrier and harmonic suppression at the output α19 α38 α57 α76 Pilot Signal Subcarrier Subcarrier Subcarrier f = 19KHz f = 38KHz f = 57KHz f = 76KHz Intermodulation (Note1) α2 α3 Pilot Signal Traffic Radio (Note 2) α57 Signal SCA - Subsidiary Communications Authorization (Note 3) α67 Signal f = 67KHz ACI - Adjacent Channel Interference (Note 4) α114 α190 Signal Signal f = 114KHz f = 190KHz Notes to the characteristics: 1. Intermodulation Suppression: measured with: 91% pilot signal; fm = 10kHz or 13kHz. 2. Traffic Radio (V.F.) Suppression: measured with: 91% stereo signal; 9% pilot signal; fm=1kHz; 5% subcarrier (f = 57kHz, fm = 23Hz AM, m = 60%) 3. SCA ( Subsidiary Communications Authorization ) measured with: 81% mono signal; 9% pilot signal; fm = 1kHz; 10%SCA - subcarrier ( fs = 67kHz, unmodulated ). 4. ACI ( Adjacent Channel Interference ) measured with: 90% mono signal; 9% pilot signal; fm =1kHz; 1% spurious signal ( fs = 110kHz or 186kHz, unmodulated). 5. By Design/Characterization but functionally guaranteed through dedicated test mode structure 13/32 TDA7461N NOISE BLANKER PART internal 2nd order 140kHz high pass filter programmable trigger threshold additional circuits for trigger adjustment (devia- tion, field-strenght) very low offset current during hold time four selectable pulse suppression times ELECTRICAL CHARACTERISTICS (continued) Symbol VTR Parameter Trigger Threshold 0) 1) Test Condition meas. with VPEAK = 0.9V VTRNOISE Noise Controlled Trigger Threshold 2) meas. with VPEAK = 1.5V Rectifier Voltage VMPX = 0mV VMPX = 50mV; f = 150KHz VMPX = 100mV; f = 150KHz means. with OVD = 11 VMPX = 800mV OVD = 10 (75KHz dev.) OVD = 01 OVD = 00 FSC = 11 means. with VMPX = 0mV FSC = 10 VLEVEL << VSBL FSC = 01 (fully mono) FSC = 00 VRECT VRECT DEV deviation dependent rectifier Voltage 3) VRECT FS Fieldstrength Controlled Rectifier Voltage 4) Min. NBT = 111 NBT = 110 NBT = 101 NBT = 100 NBT = 011 NBT = 010 NBT = 001 NBT = 000 NCT = 00 NCT = 01 NCT = 10 NCT = 11 0.5 1.5 2.2 0.5 0.9 1.7 2.5 0.5 1.0 1.5 2.0 0) All thresholds are measured using a pulse with TR = 2 µs, THIGH = 2 µs and TF = 10 µs. 1) NBT represents the Noiseblanker-Byte bits D2; D0 for the noise blanker trigger threshold 2) NAT represents the Noiseblanker-Byte bit pair D4,D3 for the noise controlled trigger adjustment 3) OVD represents the Noiseblanker-Byte bit pair D7,D6 for the over deviation detector 4) FSC represents the Fieldstrength-Byte bit pair D1,D0 for the fieldstrength control VIN VOP DC D97AU636 14/32 TR THIGH TF Time Typ. 30 35 40 45 50 55 60 65 260 220 180 140 0.9 1.7 2.5 0.9(off) 1.2 2.0 2.8 0.9(off) 1.3 1.8 2.3 Max. 1.3 2.1 2.9 1.3 1.5 2.3 3.1 1.3 1.6 2.1 2.6 Unit mVOP mVOP mVOP mVOP mVOP mVOP mVOP mVOP mVOP mVOP mVOP mVOP V V V VOP VOP VOP VOP V V V V TDA7461N Figure 14. Trigger Threshold vs. VPEAK VTH 260mV(00) 220mV(01) 180mV(10) 140mV(11) MIN. TRIG. THRESHOLD NOISE CONTROLLED TRIG. THRESHOLD 65mV 8 STEPS 30mV 0.9V D97AU648 VPEAK(V) 1.5V Figure 15. Deviation Controlled Trigger Adjustment VPEAK (VOP) 00 2.8 01 2.0 10 1.2 0.9 D97AU649 DETECTOR OFF (11) 20 32.5 45 DEVIATION(KHz) 75 Figure 16. Fieldstrength Controlled Trigger Adjustment VPEAK MONO STEREO »3V 2.3V(00) 1.8V(01) 1.3V(10) NOISE noisy signal 0.9V ATC_SB OFF (11) D98AU863 good signal E' 15/32 TDA7461N MULTIPATH DETECTOR Internal 19kHz bandpass filter Programmable bandpass and rectifier gain Two pin solution fully independent usable for external programming Selectable internal influence on Stereoblend ELECTRICAL CHARACTERISTICS (continued) Symbol Parameter fCMP Center frequency of MultipathBandpass GBPMP GRECTMP ICHMP IDISMP Test Condition Min. Typ. stereodecoder locked on pilot tone Bandpass Gain Rectifier Gain Max. 19 Unit KHz bits D2, D1 configuration byte = 00 6 dB bits D2, D1 configuration byte = 01 bits D2, D1 configuration byte = 10 bits D2, D1 configuration byte = 11 16 dB 12 18 dB dB bits D7, D6 configuration byte = 00 7.6 dB bits D7, D6 configuration byte = 01 bits D7, D6 configuration byte = 10 4.6 0 dB dB 1 1.5 µA mA Rectifier Charge Current Rectifier Discharge Current Figure 17. Block diagram of the stereodecoder DEMODULATOR MPX INGAIN INFILTER 3.5 ... 11dB STEP 2.5dB LP 80KHz 4.th ORDER DEEMPHASIS + HIGHCUT - PLOT CANC - ROLL-OFF COMP. - LP 25KHz t=50 or 75µs FM_L FM_R 100K PLL + PILOT-DET. F19 SB CONTROL REF 5V VSBL HC CONTROL D F38 A VHCCH VHCCL STEREO NOISE BLANKER HOLDN MPINFL - LEVEL INTERN MULTIPATH DETECTOR LEVEL INPUT LP 2.2KHZ 1.th ORDER GAIN 0..10dB LEVEL MPIN MPOUT D97AU762 16/32 TDA7461N DESCRIPTION OF STEREODECODER The stereodecoder part of the TDA7461N (see Fig. 17) contains all functions necessary to demodulate the MPX signal like pilot tone dependent MONO/STEREO switching as well as "stereoblend" and "highcut" functions. Adaptations like programmable input gain, roll-off compensation, selectable deemphasis time constant and a programmable fieldstrength input allow to use different IF devices. Figure 18. Signals during stereodecoder’s softmute SOFTMUTE COMMAND t STD MUTE t Stereodecoder Mute The TDA7461N has a fast and easy to control RDS mute function which is a combination of the audioprocessor softmute and the high-ohmic mute of the stereodecoder. If the stereodecoder is selected and a softmute command is sent (or activated through the SM pin) the stereodecoder will be set automatically to the high-ohmic mute condition after the audio signal has been softmuted. Hence a checking of alternate frequencies could be performed. To release the system from the mute condition simply the unmute command must be sent: the stereodecoder is unmuted immediately and the audioprocessor is softly unmuted. Fig. 18 shows the output signal VO as well as the internal stereodecoder mute signal. This influence of Softmute on the stereodecoder mute can be switched off by setting bit 3 of the Softmute byte to "0". A stereodecoder mute command (bit 0, stereodecoder byte set to "1") will set the stereodecoder in any case independently to the high-ohmic mute state. If any other source than the stereodecoder is selected the decoder remains muted and the MPX pin is connected to Vref to avoid any discharge of the coupling capacitor through leakage currents. Input Stages The Ingain stage allows to adjust the MPX signal to a magnitude of about 1Vrms internally which is the recommended value. The 4.th order input filter has a corner frequency of 80kHz and is used to attenuate spikes and noise and acts as an antialiasing filter for the following switch capacitor filters. Demodulator In the demodulator block the left and the right channel are separated from the MPX signal. In this stage also the 19 kHz pilot tone is cancelled. For reaching a high channel separation the TDA7461N offers an I2C bus programmable rolloff adjustment which is able to compensate the VO D97AU638 t lowpass behaviour of the tuner section. If the tuner attenuation at 38kHz is in a range from 20.2% to 31% the TDA7461N needs no external network before the MPX pin. Within this range an adjustment to obtain at least 40dB channel separation is possible. The bits for this adjustment are located together with the fieldstrength adjustment in one byte. This gives the possibility to perform an optimization step during the production of the carradio where the channel separation and the fieldstrength control are trimmed. Deemphasis and Highcut. The lowpass filter for the deemphasis allows to choose between a time constant of 50µs and 75µs (bit D7, Stereodecoder byte). The highcut control range will be in both cases tHC = 2 ⋅ tDeemp. Inside the highcut control range (between VHCH and VHCL) the LEVEL signal is converted into a 5 bit word which controls the lowpass time constant between t Deemp...3 ⋅ tDeemp. There by the resolution will remain always 5 bits independently of the absolute voltage range between the VHCH and VHCL values. The highcut function can be switched off by I2C bus (bit D7, Fieldstrength byte set to "0"). PLL and Pilot Tone Detector The PLL has the task to lock on the 19kHz pilotone during a stereo transmission to allow a correct demodulation. The included detector enables the demodulation if the pilot tone reaches the selected pilottone threshold VPTHST. Two different thresholds are available. The detector output (signal STEREO, see block diagram) can be checked 17/32 TDA7461N by reading the status byte of the TDA7461N via I2C bus. Figure 19. Internal stereoblend characteristics Fieldstrength Control The fieldstrength input is used to control the high cut and the stereoblend function. In addition the signal can be also used to control the noiseblanker thresholds. LEVEL Input and Gain To suppress undesired high frequency modulation on the highcut and stereoblend function the LEVEL signal is lowpass filtered firstly. The filter is a combination of a 1st order RC lowpass at 53kHz (working as anti-aliasing filter) and a 1storder switched capacitor lowpass at 2.2kHz. The second stage is a programmable gain stage to adapt the LEVEL signal internally to different IF. The gain is widely programmable in 16 steps from 0dB to 10dB (step = 0.67dB). These 4 bits are located together with the Roll-Off bits in the "Stereodecoder Adjustment" byte to simplify a possible adaptation during the production of the carradio. gain LG and VSBL. To adjust the voltage where the full channel separation is reached (VST) the LEVEL gain LG has to be defined. The following equation can be used to estimate the gain: LG = REF5V Field strength voltage [STEREO] The gain can be programmed through 4 bits in the "Stereodecoder-Adjustment" byte. The MONO voltage VMO (0dB channel separation) can be choosen selecting 33, 42, 50 or 58% of REF5V. All necessary internal reference voltages like REF5V are derived from a bandgap circuit. Therefore they have a temperature coefficient near zero. This is useful if the fieldstrength signal is also temperature compensated. But most IF devices apply a LEVEL voltage with a TC of 3300ppm. The TDA7461N offers this TC for the reference voltages, too. The TC is selectable with bit D7 of the "stereodecoder adjustment" byte. Stereoblend Control The stereoblend control block converts the internal LEVEL voltage (LEVEL INTERN) into an demodulator compatible analog signal which is used to control the channel separation between 0dB and the maximum separation. Internally this control range has a fixed upper limit which is the internal reference voltage REF5V. The lower limit can be programmed to be 33%, 42%, 50% or 58% of REF5V (see fig. 20). To adjust the external LEVEL voltage to the internal range two values must be defined: the LEVEL Figure 20. Relation between internal and external LEVEL voltage and setup of Stereoblend INTERNAL VOLTAGES INTERNAL VOLTAGES SETUP OF VST SETUP OF VMO LEVEL INTERN REF 5V REF 5V 58% 50% VSBL 42% 33% LEVEL VSBL VMO 18/32 LEVEL INTERN VST t FIELDSTRENGHT VOLTAGE D97AU639 VMO VST t FIELDSTRENGHT VOLTAGE TDA7461N Highcut Control The highcut control setup is similar to the stereoblend control setup : the starting point VHCH can be set with 2 bits to be 42, 50, 58 or 66% of REF5V whereas the range can be set to be 17 or 33% of VHCH (see fig. 21). supplied by his own biasing circuit. Trigger Path The incoming MPX signal is highpass filtered, amplified and rectified. This second order highpass-filter has a corner frequency of 140kHz. The rectified signal, RECT, is lowpass filtered to generate a signal called PEAK. Also noise with a frequency 140kHz increases the PEAK voltage. The PEAK voltage is fed to a threshold generator, which adds to the PEAK voltage a DC dependent threshold VTH. Both signals, RECT and PEAK+VTH are fed to a comparator which triggers a re-triggerable monoflop. The monoflop’s output activates the sample-and-hold circuits in the signalpath for 40µs. Figure 21. Highcut characteristics LOWPASS TIME CONSTANT 3•τDeemp The block diagram of the noiseblanker is given in fig.22. τDeemp D97AU640 Automatic Noise Controlled Threshold Adjustment (ATC) There are mainly two independent possibilities for programming the trigger threshold: FUNCTIONAL DESCRIPTION OF THE NOISEBLANKER In the automotive environment the MPX signal is disturbed by spikes produced by the ignition and for example the wiper motor. The aim of the noiseblanker part is to cancel the audible influence of the spikes. Therefore the output of the stereodecoder is held at the actual voltage for 40µs. In a first stage the spikes must be detected but to avoid a wrong triggering on high frequency (white) noise a complex trigger control is implemented. Behind the triggerstage a pulse former generates the "blanking" pulse. To avoid any crosstalk to the signalpath the noiseblanker is a the low threshold in 8 steps (bits D0 to D2 of the noiseblanker byte) b the noise adjusted threshold in 4 steps (bits D3 and D4 of the noiseblanker byte, see fig. 14). The low threshold is active in combination with a good MPX signal without any noise; the PEAK voltage is less than 1V. The sensitivity in this operation is high. If the MPX signal is noisy the PEAK voltage increases due to the higher noise, which is also rectified. With increasing of the PEAK voltage the trigger threshold increases, too. This particular gain is programmable in 4 steps (see fig. 14). VHCL VHCH FIELDSTRENGHT Figure 22. Block diagram of the noiseblanker MPX HIGH PASS RECTIFIER RECT + - + HOLDN VTH PEAK LOWPASS MONOFLOP THRESHOLD GENERATOR + ADDITIONAL THRESHOLD CONTROL D98AU861 19/32 TDA7461N Automatic Threshold Control Besides the noise controlled threshold adjustment there is an additional possibility for influencing the trigger threshold. It is depending on the stereoblend control. The point where the MPX signal starts to become noisy is fixed by the RF part. Therefore also the starting point of the normal noise-controlled trigger adjustment is fixed (fig. 16). In some cases the behaviour of the noiseblanker can be improved by increasing the threshold even in a region of higher fieldstrength. Sometimes a wrong triggering occures for the MPX signal often shows distortion in this range which can be avoided even if using a low threshold. Because of the overlap of this range and the range of the stereo/mono transition it can be controlled by stereoblend. This threshold increase is programmable in 3 steps or switched off with bits D0 and D1 of the fieldstrength control byte. used to increase the PEAK voltage. Offset and gain of this circuit are programmable in 3 steps with the bits D6 and D7 of the stereodecoder byte (the first step turns off the detector, see fig. 15). Over Deviation Detector If the system is tuned to stations with a high deviation the noiseblanker can trigger on the higher frequencies of the modulation. To avoid this wrong behaviour, which causes noise in the output signal, the noiseblanker offers a deviation dependent threshold adjustment. By rectifying the MPX signal a further signal representing the actual deviation is obtained. It is TEST MODE During the test mode which can be activated by setting bit D0 of the testing byte and bit D5 of the subaddress byte to "1" several internal signals are available at the CASSR pin. During this mode the input resistance of 100kOhm is disconnected from the pin. The internal signals available are shown in the software specification. FUNCTIONAL DESCRIPTION OF THE MULTIPATH DETECTOR Using the internal detector the audible effects of a multipath condition can be minimized. A multipath condition is detected by rectifying the 19kHz spectrum in the fieldstrength signal. Selecting the "internal influence" in the configuration byte, the channel separation is automatically reduced during a multipath condition according to the voltage appearing at the MPOUT pin. To obtain a optimal performance an adaptation is necessary. Therefore the gain of the 19kHz bandpass is programmable in four steps as well as the rectifier gain. The attack and decay times can be set by the external capacitor value. Figure 23. Block diagram of the Multipath Detector LEVEL to SB VDD int. INFLUENCE DC=1µA MPIN BANDPASS 19KHz RECTIFIER MPOUT GAIN 2 BITS 20/32 GAIN 2 BITS 220nF D97AU880 TDA7461N Figure 24. Application Example 1 SOUND EFFECTS ACOUTL ACOUTR ACINR ACINL CREF VS 10µF +VCC = 100nF OUTLF OUTLF 9V OUTRF 100nF OUTRF CASS R CASS R OUTLR 100nF OUTLR CASS L CASS L 100nF TDA7461 CDR CDR OUTRR MPX 22µF CDG CDG AM 100nF CDL CDL 220nF 220nF AM SDA SCL SCL SMUTE SMUTE LEVEL PHONE PHONE MPX 220nF SDA PHONE_GND PHGND OUTRR 220nF LEVEL GND D97AU763A MPIN MPOUT MUXR UNWEIGHTED LEVEL MUXL 220nF Note: Bit D7 of "Bass and Treble Filter characteristics" set to 1 Figure 25. Application Example 2 PRE-SPEAKER OUTPUT ADDITIONAL INPUT 100nF ACOUTL ACOUTR 100nF ACINR VS ACINL CREF 10µF +VCC 100nF = OUTLF OUTLF 9V 100nF CASS R 100nF CASS L 100nF CDR 22µF CDG 100nF CDL 220nF PHGND 220nF PHONE OUTRF OUTRF CASS R OUTLR OUTLR CASS L CDR TDA7461 OUTRR MPX CDG AM CDL OUTRR 220nF MPX 220nF AM SDA SDA SCL PHONE_GND SCL SMUTE SMUTE LEVEL PHONE LEVEL GND D97AU764 MPIN MPOUT UNWEIGHTED LEVEL MUXR MUXL 220nF Note: Bit D7 of "Bass and Treble Filter characteristics" set to 0 21/32 TDA7461N I2C BUS INTERFACE DESCRIPTION Interface Protocol The interface protocol comprises: -a start condition (S) -a chip address byte (the LSB bit determines read CHIP ADDRESS MSB S 1 SUBADDRESS LSB 0 0 0 1 1 / write transmission) -a subaddress byte -a sequence of data (N-bytes + acknowledge) -a stop condition (P) DATA 1 to DATA n MSB 0 R/W ACK LSB X AZ T I A3 A2 A1 A0 MSB LSB DATA ACK ACK P D97AU627 S = Start ACK = Acknowledge AZ = AutoZero-Remain T = Testing I = Autoincrement P = Stop MAX CLOCK SPEED 500kbits/s Auto increment If bit I in the subaddress byte is set to "1", the autoincrement of the subaddress is enabled. The transmitted data is automatically updated after each ACK. Transmission can be repeated without new chip address. SM = Soft mute activated ST = Stereo X = Not Used TRANSMITTED DATA (send mode) MSB X LSB X X X ST SM X SUBADDRESS (receive mode) MSB X LSB AZ T T = Testmode I = Autoincrement AZ = Auto Zero Remain X = not used 22/32 I A3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 A2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 A1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 A0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 FUNCTION Input selector Loudness / Auto-Zero Volume Softmute / Beep Bass / Treble Attenuator Bass / Treble Configuration Speaker attenuator LF Speaker attenuator LR Speaker attenuator RF Speaker attenuator RR / Blanktime adjust Stereodecoder Noiseblanker Fieldstrength Control Configuration Stereodecoder Adjustment Testing X TDA7461N DATA BYTE SPECIFICATION Input Selector MSB D7 FUNCTION LSB D6 D5 D4 D3 D2 D1 D0 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 0 1 1 1 1 0 0 1 1 0 0 0 1 1 0 0 1 0 0 : 1 1 0 0 : 1 1 0 1 : 0 1 Source Selector CD Cassette Phone AM Stereo Decoder Input FM Mute AC inputs CD Mode CD Full-differential CD Quasi-diff AM/FM Mode AM mono AM stereo AM through Stereodecoder FM- Stereodecoder In-Gain 14dB 12dB : 2 dB 0 dB For example to select the CD input in quasi-differential mode with gain of 8dB the Data Byte is: 0/01111000 Loudness MSB D7 D6 D5 D4 0 1 0 1 0 1 1 LOUDNESS LSB D3 D2 D1 D0 0 0 : 1 1 0 0 : 1 1 0 0 : 1 1 0 1 : 0 1 Attenuation 0dB -1dB : -14dB -15dB Filter on off (flat) Center Frequency 200Hz 400Hz Loudness Q low (1st order) normal (2nd order) must be "1" Note: The attenuation is specified at high frequencies. Around the center frequency the value is different depending on the programmed attenuation (see Loudness frequency response). 23/32 TDA7461N Mute, Beep and Mixing MSB D7 LSB D6 D5 D4 D3 D2 D1 0 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 0 1 1 MUTE/BEEP/MIXING D0 0 1 0 1 Mute Enable Softmute Disable Softmute Mute time =0.48 ms Mute time =0.96 ms Mute time =40.4 ms Mute time =324 ms Stereo Decoder Softmute Influence = off Stereo Decoder Softmute Influence = on Beep Beep Frequency = 600Hz Beep Frequency = 1.2KHz Mixing Mix-Source = Beep Mix-Source = Phone Full Mix Signal Source -12dB + Mix-Signal -2.5dB Source -6dB + Mix-Signal -6dB Full Source Note: for more information to the Stereodecoder-Softmute-Influence please refer to the stereodecoder description. Volume MSB D7 0 1 LSB D6 D5 D4 D3 D2 D1 D0 0 0 : 0 0 0 : 0 0 0 : 1 1 0 0 : 0 0 0 : 0 1 1 : 1 1 0 0 : 0 0 0 : 1 0 0 : 0 0 0 0 : 1 1 1 : 1 0 0 : 1 1 0 0 : 1 1 1 : 1 0 0 : 1 1 0 0 : 0 0 1 : 1 0 0 : 1 1 0 1 : 0 1 0 : 1 0 1 : 0 1 ATTENUATION Gain/Attenuation +32dB +31dB : +20dB +19dB +18dB : +1dB 0dB - 1dB : -78dB -79dB Softstep Softstep Volume = off Softstep Volume = on Note: It is not recommended to use a gain more than 20dB for system performance reason. In general, the max. gain should be limited by software to the maximum value, which is needed for the system. 24/32 TDA7461N Bass & Treble Attenuation MSB D7 0 0 : 0 0 1 1 : 1 1 LSB D6 0 0 : 1 1 1 1 : 0 0 D5 0 0 : 1 1 1 1 : 0 0 D4 D3 D2 D1 D0 0 0 : 0 0 1 1 : 1 1 0 0 : 1 1 1 1 : 0 0 0 0 : 1 1 1 1 : 0 0 0 1 : 0 1 1 0 : 1 0 BASS & TREBLE ATTENUATION Treble Steps -14dB -12dB : -2dB 0dB 0dB +2dB : +12dB +14dB Bass Steps -14dB -12dB : -2dB 0dB 0dB +2dB : +12dB +14dB 0 1 : 0 1 1 0 : 1 0 For example 12dB Treble and -8dB Bass give the following DATA BYTE : 0 0 1 1 1 0 0 1. Bass & Treble Filter Characteristics MSB D7 LSB D6 D5 1 0 0 1 1 D4 1 0 1 0 1 D3 0 0 1 1 1 D2 D1 D0 0 0 1 1 0 1 0 1 0 1 0 1 1 0 1 0 1 BASS & TREBLE FILTER Treble Center Frequency = 10 KHz Center Frequency = 12.5 KHz Center Frequency = 15 KHz Center Frequency = 17.5 KHz Bass Center Frequency = 60 Hz Center Frequency = 70 Hz Center Frequency = 80 Hz Center Frequency = 100Hz Center Frequency = 150Hz Quality factor = 1 Quality factor = 1.25 Quality factor = 1.5 Quality factor = 2 DC-Gain = 0dB DC-Gain = ±4.4dB AC Coupling (*) For External Connection Internally connected For example Treble center frequency = 15kHz, Bass center frequency = 100Hz, Bass Q = 1 and DC = 0dB give the following DATA BYTE: 1 0001110 (*) For deeper information see application examples fig. 24 and fig. 25. 25/32 TDA7461N Speaker Attenuation (LF, LR, RF, RR) MSB D7 LSB D6 1 1 0 0 1 1 0 1 0 1 0 1 26/32 D5 D4 D3 D2 D1 D0 0 0 : 0 0 0 0 0 0 0 0 0 1 0 0 : 1 1 1 1 1 1 1 1 1 0 0 : 0 1 1 1 1 1 1 1 1 0 0 : 1 0 0 0 0 1 1 1 1 0 0 : 1 0 0 1 1 0 0 1 1 0 1 : 1 0 1 0 1 0 1 0 1 Attenuation 0dB -1dB : -23dB -24.5dB -26dB -28dB -30 -32dB -35dB -40dB -50dB Speaker Mute Must be "1" (except RF, RR speaker; see below) Blank Time adj. (subaddress speaker RR) 38µs 25.5µs 32µs 22µs Output selector for pins 15 and 16. (subaddress spaeaker RF) Stereodecoder output selected Input multiplexer output selected TDA7461N Stereodecoder MSB D7 FUNCTION LSB D6 D5 D4 D3 D2 D1 D0 0 1 0 0 1 1 IN-Gain 11dB IN-Gain 8.5dB IN-Gain 6dB IN-Gain 3.5dB 0 1 0 1 1 Stereodec Unmuted with Stdec Input selected and automatically Muted at the selection of any other source. Stereodec Unmuted whichever is the selected source. 0 1 1 STD Unmuted STD Muted 0 1 Forced MONO MONO/STEREO switch automatically 0 1 Pilot Threshold HIGH Pilot Threshold LOW 0 1 Deemphasis 50µs Deemphasis 75µs Noiseblanker MSB D7 LSB D6 D5 D4 0 0 1 1 0 1 0 0 1 1 0 1 0 1 D3 0 1 0 1 D2 0 0 0 0 1 1 1 1 D1 0 0 1 1 0 0 1 1 D0 0 1 0 1 0 1 0 1 FUNCTION Low Threshold 65mV Low Threshold 60mV Low Threshold 55mV Low Threshold 50mV Low Threshold 45mV Low Threshold 40mV Low Threshold 35mV Low Threshold 30mV Noise Controlled Threshold 320mV Noise Controlled Threshold 260mV Noise Controlled Threshold 200mV Noise Controlled Threshold 140mV Noise blanker OFF Noise blanker ON Over deviation Adjust 2.8V Over deviation Adjust 2.0V Over deviation Adjust 1.2V Over deviation Detector OFF 27/32 TDA7461N Fieldstrength Control MSB D7 FUNCTION LSB D6 D5 D4 D3 0 0 1 1 0 0 1 1 D2 D1 D0 0 0 1 1 0 1 0 1 Noiseblanker Field strength Adj 2.3V Noiseblanker Field strength Adj 1.8V Noiseblanker Field strength Adj 1.3V Noiseblanker Field strength Adj OFF VSBL at 33% REF 5V VSBL at 42% REF 5V VSBL at 50% REF 5V VSBL at 58% REF 5V 0 1 0 1 VHCH at 42% REF 5V VHCH at 50% REF 5V VHCH at 58% REF 5V VHCH at 66% REF 5V 0 1 0 1 1 0 VHCL at 17% VHCH VHCL at 33% VHCH 0 1 High cut OFF High cut ON Configuration MSB D7 LSB D6 D5 D4 D3 0 0 1 1 0 1 1 0 0 1 1 28/32 0 1 0 1 D2 0 1 0 1 D1 D0 0 0 1 1 0 1 0 1 FUNCTION Noise Rectifier Discharge Resistor R = infinite R = 56kΩ R = 33kΩ R =18kΩ Multipath Detector Bandpass Gain 6dB 16dB 12dB 18dB Multipath Detector internal influence ON OFF Must be "1" Multipath Detector Reflection Gain Gain = 7.6dB Gain = 4.6dB Gain = 0dB OFF TDA7461N Stereodecoder Adjustment MSB D7 LSB D6 D5 D4 D3 0 0 0 : 1 0 0 0 : 1 0 0 1 : 1 0 1 0 : 1 D6 D5 D4 D3 D2 D1 D0 0 0 0 : 1 : 1 0 0 1 : 0 : 1 0 1 0 : 0 : 1 D2 D1 0 1 FUNCTION Roll-Off Compensation not allowed 20.2% 21.9% : 25.5% : 31.0% LEVEL Gain 0dB 0.66dB 1.33dB : 10dB Temperature compensation at LEVEL input TC = 0 TC = 16.7mV/K (3300ppm) Testing MSB D7 LSB 0 1 0 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 1 0 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 FUNCTION D0 Stereodecoder test signals OFF Test signals enabled if bit D5 of the subaddress (test mode bit) is set to "1", too External Clock Internal Clock Testsignals at CASS_R VHCCH Level intern Pilot magnitude VCOCON; VCO Control Voltage Pilot threshold HOLDN NB threshold F228 VHCCL VSBL not used not used PEAK not used REF5V not used VCO OFF ON Audioprocessor test mode only if bit D5 of the subaddress (test mode bit) is set to "1" OFF Note : This byte is used for testing or evaluation purposes only and must not be set to other values than the default "11111110" in the application! 29/32 TDA7461N mm DIM. MIN. TYP. A inch MAX. MIN. TYP. 2.65 MAX. 0.104 a1 0.1 0.3 0.004 0.012 b 0.35 0.49 0.014 0.019 b1 0.23 0.32 0.009 0.013 C 0.5 c1 0.020 45° (typ.) D 17.7 18.1 0.697 0.713 E 10 10.65 0.394 0.419 e 1.27 0.050 e3 16.51 0.65 F 7.4 7.6 0.291 0.299 L 0.4 1.27 0.016 0.050 S 30/32 OUTLINE AND MECHANICAL DATA 8 ° (max.) SO28 TDA7461N mm inch DIM. MIN. TYP. MAX. MIN. TYP. a1 0.63 0.025 b 0.45 0.018 b1 0.23 b2 0.31 1.27 D E 0.009 0.012 0.050 37.34 15.2 16.68 1.470 0.598 0.657 e 2.54 0.100 e3 33.02 1.300 F MAX. OUTLINE AND MECHANICAL DATA 14.1 0.555 I 4.445 0.175 L 3.3 0.130 DIP28 31/32 TDA7461N Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners © 2003 STMicroelectronics - All rights reserved STMicroelectronics GROUP OF COMPANIES Australia – Belgium - Brazil - Canada - China – Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States www.st.com 32/32