THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 WIDEBAND FIXED-GAIN AMPLIFIER FEATURES APPLICATIONS • • • • • • • • • • • • • • Fixed Closed-Loop Gain Amplifier – 10 V/V (20 dB) Wide Bandwidth: 1.8 GHz High Slew Rate: 5500 V/µs Low Total Input Referred Noise: 2.5 nV/√Hz Low Distortion – HD2: –65 dBc at 70 MHz – HD3: –76 dBc at 70 MHz – IMD3: –85 dBc at 100 MHz – OIP3: 34 dBm at 100 MHz – IMD3: –70 dBc at 300 MHz – OIP3: 27 dBm at 300 MHz High Output Drive: ±180 mA Power Supply Voltage: 3 V or 5 V Wideband Signal Processing Wireless Transceivers IF Amplifier ADC Preamplifier DAC Output Buffers Test, Measurement, and Instrumentation Medical and Industrial Imaging DESCRIPTION The THS4303 device is a wideband, fixed-gain amplifier that offers high bandwidth, high slew rate, low noise, and low distortion. This combination of specifications enables analog designers to transcend current performance limitations and process analog signals at much higher speeds than previously possible with closed-loop, complementary amplifier designs. The devices are offered in a 16-pin leadless package and incorporate a power-down mode for quiescent power savings. VS+ + FB 22 µF 0.1 µF 47 pF SMALL SIGNAL FREQUENCY RESPONSE 22 30.1 Ω Rg 50 Ω Source 50 Ω Load _ + VI THS4303 49.9 Ω VO 49.9 Ω VS− 20 Small Signal Gain − dB Rf 18 16 14 12 RL = 100 Ω VO = 100 mVPP VS = 5 V 10 + 22 µF FB 100 k 47 pF 0.1 µF 1M 10 M 100 M 1G 10 G f − Frequency − Hz 30.1 Ω FB = Ferrite Bead Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2003–2005, Texas Instruments Incorporated THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. ABSOLUTE MAXIMUM RATINGS over operating free-air temperature range unless otherwise noted (1) UNIT VS Supply voltage 6V VI Input voltage ±VS IO Output current 200 mA Continuous power dissipation See Dissipation Rating Table TJ( (2)) ( (3)) Maximum junction temperature 150°C TJ Maximum junction temperature, continuous operation, longterm reliability TA Operating free-air temperature range –40°C to 85°C Tstg Storage temperature range –65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 125°C 300°C ESD ratings: (1) (2) (3) HBM 3000 CDM 1500 MM 200 Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those specified is not implied. The THS4303 device may incorporate a PowerPAD™ on the underside of the chip. This acts as a heatsink and must be connected to a thermally dissipative plane for proper power dissipation. Failure to do so may result in exceeding the maximum junction temperature which can permanently damage the device. See TI technical brief SLMA002 and SLMA004 for more information about utilizing the PowerPAD thermally enhanced package. The absolute maximum temperature under any condition is limited by the constraints of the silicon process. RGT PACKAGE 2 11 3 10 4 5 6 7 VOUT NC = No connect 2 NC V IN− 16 15 14 13 12 Rg 1 Rf VS− V IN+ PD (TOP VIEW) 8 9 VS+ THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 RECOMMENDED OPERATING CONDITIONS (1) Dual supply Supply voltage, (VS+ and VS–) MAX ±1.5 ±2.5 3 5 VS–+1 VS+–1 Single supply Input common-mode voltage range (1) MIN UNIT V V This data was taken using 2 oz. trace and copper pad that is soldered directly to a 3 in. x 3 in. PCB. For further information, refer to Application Information section of this data sheet. PACKAGE DISSIPATION RATINGS (1) (2) PACKAGE ΘJC(°C/W) ΘJA(°C/W) RGT-16 (2) 2.4 39.5 POWER RATING (1) TA≤ 25°C TA =85°C 2.53 W 1.01 W Power rating is determined with a junction temperature of 125°C. This is the point where distortion starts to substantially increase. Thermal management of the final PCB should strive to keep the junction temperature at or below 125°C for best performance and long term reliability. This data was taken using 2 oz. trace and copper pad that is soldered directly to a 3 in. x 3 in. PCB. For further information, refer to Application Information section of this data sheet. AVAILABLE OPTIONS PACKAGED DEVICES (1) TA LEADLESS GAIN –40°C to 85°C (1) RGT-16 THS4303RGTR +10 THS4303RGTT Packages are available taped and reeled. The R suffix standard quantity is 3000. The T suffix standard quantity is 250. INTERNAL FIXED RESISTOR VALUES DEVICE GAIN (V/V) Rf Rg THS4303 +10 450 50 3 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 ELECTRICAL CHARACTERISTICS THS4303 (Gain = +10 V/V) Specifications: VS = 5 V, RL = 100 Ω, (unless otherwise noted) TYP PARAMETER TEST CONDITIONS OVER TEMPERATURE UNITS MIN/ MAX 1.8 GHz Typ 18 GHz Typ 25°C 25°C 0°C to 70°C –40°C to 85°C AC PERFORMANCE Small signal bandwidth G = +10, VO = 200 mVRMS Gain bandwidth product Full-power bandwidth G = +10, VO = 2 Vpp Slew rate G = +10, VO = 2 V Step 1.5 GHz Typ 5500 V/µs Min RL = 100 Ω –65 dBc RL = 1 k Ω –75 dBc RL = 100 Ω –76 dBc RL = 1 kΩ –80 dBc Harmonic distortion Second harmonic distortion G = +10, VO = 1 VPP, f = 70 MHz Third harmonic distortion Typ Typ Third order intermoduation (IMD3) VO = 1 VPP envelope, 200 kHz tone spacing fc= 100 MHz –85 dBc fc = 300 MHz –70 dBc Third order output intercept (OIP3) VO = 1 VPP, 200 kHz tone spacing fc = 100 MHz 34 dBm fc = 300 MHz 27 dBm Total input referred noise f = 1 MHz 2.5 nV/√Hz Typ Noise figure f = 100 MHz 16 dB Typ Typ Typ DC PERFORMANCE Voltage gain VI = ±50 mV, VCM = 2.5 V Input offset voltage Average offset voltage drift Input bias current VCM = 2.5 V 9.9 9.8 9.8 9.8 V/V Min 9.9 10 10 10 V/V Max 1.5 4.25 5.25 5.25 mV Max ±20 ±20 µV/°C Typ 7 10 13 15 µA Max ±55 ±55 nA/°C Typ Min Average bias current drift INPUT CHARACTERISTICS Common-mode input range Common-mode rejection ratio VCM = 2 V to 3 V Noninverting input impedance 1/4 1.1 / 3.9 1.2 / 3.8 1.2 / 3.8 V 60 52 50 50 dB Min MΩ pF Typ 1.6 1 OUTPUT CHARACTERISTICS Output voltage swing 1/4 1.1 / 3.9 1.2 / 3.8 1.2 / 3.8 V Min 180 170 165 160 mA Min RL = 5 Ω 180 170 165 160 mA Min f = 10 MHz 0.08 Ω Typ Output current (sourcing) RL = 5 Ω Output current (sinking) Output impedance POWER SUPPLY Specified operating voltage 5 5.5 5.5 5.5 V Max Maximum quiescent current 34 41 46 48 mA Max Minimum quiescent current 34 27 25 23 mA Min Power supply rejection (PSRR +) VS+ = 5 V to 4.5 V, VS– = 0 V 63 54 52 51 dB Min Power supply rejection (PSRR –) VS+ = 5 V, VS– = 0 V to 0.5 V 65 58 56 54 dB Min 4 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 ELECTRICAL CHARACTERISTICS (continued) THS4303 (Gain = +10 V/V) Specifications: VS = 5 V, RL = 100 Ω, (unless otherwise noted) TYP PARAMETER TEST CONDITIONS OVER TEMPERATURE 25°C 25°C 0°C to 70°C –40°C to 85°C UNITS MIN/ MAX mA Max POWER-DOWN CHARACTERISTICS Maximum power-down current 0.9 1.2 Power-on voltage threshold PD = 0 V 1.1 1.5 1.3 1.4 V Min Power-down voltage threshold 1.1 0.9 V Max Turnon time delay [t(ON)] 90% of final value 42 ns Typ Turnoff time delay [t(Off)] 10% of final value 35 ns Typ 100 kΩ Typ 470 Ω Typ Input impedance Output impedance f = 100 kHz SCHEMATIC DIAGRAM Input Stage Gain Stage Output Stage VCC I24 I25 R13 I30 R17 I29 D7 D10 Q56 Q55 Q53 Q51 Q65 Q61 Q60 Q64 IN_POS R14 OUT Q54 Q52 Q58 Q57 D9 C3 Q63 Q66 Q59 Q62 I28 D8 I26 I31 I27 R15 R16 VEE VCC D13 R19 R18 IN_NEG D14 VEE 5 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 TYPICAL CHARACTERISTICS TABLE OF GRAPHS (5 V) FIGURE S-parameter vs Frequency 1 Small signal frequency response 2 Large signal frequency response 3 Slew rate vs Output voltage 4 Harmonic distortion vs Frequency 5, 6 Harmonic distortion vs Output voltage swing 7 Second order intermodulation distortion vs Frequency 8 Third order intermodulation distortion vs Frequency 9 Second order intercept point vs Frequency 10 Third order intercept point vs Frequency 11 Voltage and current noise vs Frequency 12 Settling time 13, 14 Quiescent current vs Supply voltage 15 Output voltage vs Load resistance 16 Capacitive load frequency response 17 Gain vs Case temperature 18 Rejection ratio vs vs Frequency 19 Rejection ratios vs Case temperature 20 Common-mode rejection ratio vs Input common-mode range 21 Input offset voltage vs Case temperature 22 Positive input bias current vs Case temperature 23 Small signal transient response 24 Large signal transient response 25 Overdrive recovery 26 Closed-loop output impedance vs Frequency 27 Power-down quiescent current vs Supply voltage 28 Power-down S-parameter vs Frequency 29 Power-down output impedance vs Frequency 30 Turnon and turnoff delay times 31 TABLE OF GRAPHS (3 V) FIGURE S-parameter vs Frequency 32 Small signal frequency response 33 Large signal frequency response 34 Harmonic distortion vs Frequency 35 Slew rate vs Output voltage 36 Capacitive load frequency response 37 Gain vs Case temperature 38 Input offset voltage vs Case temperature 39 Positive input bias current vs Case temperature 40 Overdrive recovery 41 Power-down S-parameter vs Frequency 42 6 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 TYPICAL TEST DATA S-Parameter (Measured using standard THS4303EVM, edge number 6454762, with VS = 5 V in a 50 Ω test system) Frequency (MHz) S11 (dB) S11 (Ang) S21 (dB) S21 (Ang) 1 –50.68359 –9.936035 20.07422 1.007886 2 –50.80664 –3.452515 20.08398 2.060587 10 –51.10547 –38.07227 20.02734 10.158346 50 –37.71289 –76.30078 20.08252 50.078859 100 –34.61719 –109.6055 20.29541 150 –31.50684 –105.7422 200 –29.81348 –105.3516 250 –29.20801 300 S12 (dB) S12 (Ang) S22 (dB) S22 (Ang) –75.9375 74.27344 –52.6047 –9.367676 –77.44531 –30.31445 –51.9668 8.862793 –80.94922 53.79102 –47.64258 42.5957 –63.52539 –72.41406 –59.52539 –91.70703 102.38457 –57.58594 74.66016 –30.39063 125.332 20.40576 150.47685 –52.71875 18.20898 –24.91895 102.4297 20.44922 198.11759 –53.94141 53.86523 –22.96484 89.09766 –129.6016 20.43213 246.87998 –52.35938 40.63672 –22.02344 79.55469 –26.57422 –100.0703 20.40088 307.6446 –54.19336 81.05859 –21.18359 73.59766 350 –25.90137 –102.1328 20.34033 362.84524 –53.47266 –38.93164 –20.597766 71.20313 400 –24.89551 –111.4609 20.2959 405.04485 –54.37109 12.90479 –20.03906 71.91797 450 –24.7002 –76.46094 20.22754 452.15154 –53.91797 14.76416 –19.84668 74.58203 500 –25.76758 –95.54688 20.16406 504.73809 –55.60156 34.66016 –19.11621 73.60547 550 –24.86231 –98.39844 20.05273 563.4396 –57.78125 –114.1016 –18.54688 78.37109 600 –23.49805 –106.6992 19.97656 595.30346 –61.00977 –60.50586 –18.15332 76.28125 700 –21.07422 –84.68359 19.76318 702.11941 –64.83984 –67.44531 –17.24609 79.64063 800 –19.82617 –86.29688 19.60352 828.09966 –72.0625 72.92578 –15.36182 84.96875 900 –18.98828 –86.40625 19.44287 924.40782 –61.43359 172.7109 –14.03223 87.03125 1000 –17.16211 –82.15234 19.24219 1031.9205 –54.25391 165.2578 –12.65723 87.64844 1250 –14.66065 –83.30469 18.59424 1285.9052 –46.52148 163.7813 –10.12158 81.31641 1500 –12.67529 –90.48438 17.96533 1516.6333 –41.23242 159.5156 –8.850586 79.875 1750 –11.51025 –104.2656 17.229 1788.7621 –37.59766 145.8125 –7.762695 76.54688 2000 –10.52832 –106.4531 16.30127 1996.8001 –35.54688 154.1719 –7.215088 76.26953 7 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 TYPICAL THS4303 CHARACTERISTICS (5 V) S-PARAMETER vs FREQUENCY SMALL SIGNAL FREQUENCY RESPONSE 22 40 VS = 5 V 20 0 S22 −20 S11 −40 −60 18 16 14 RL = 100 Ω VO = 100 mVPP VS = 5 V S12 12 −80 1M 10 M 100 M 1G 10 G 100 k 1M −55 10 M 100 M 1G 0 10 G 100 k Rise 3000 2000 0.5 1 1.5 2 VO − Output Voltage − VPP −55 RL = 100 Ω VS = 5 V −60 Harmonic Distortion − dBc 1M 10 M 100 M f − Frequency − Hz 1G HD3, VO = 2 VPP −65 HD2, VO = 2 VPP −70 −75 −80 HD3, VO = 1 VPP −85 HD2, VO = 1 VPP −90 −70 −75 −85 −90 −100 −100 10 f − Frequency − MHz HD2, VO = 2 VPP −80 −95 1 HD3, VO = 2 VPP −65 −95 2.5 10 G RL = 1 kΩ VS = 5 V −60 100 HD2, VO = 1 VPP HD3, VO = 1 VPP 1 10 f − Frequency − MHz 100 Figure 6. HARMONIC DISTORTION vs OUTPUT VOLTAGE SWING SECOND-ORDER INTERMODULATION DISTORTION vs FREQUENCY THIRD-ORDER INTERMODULATION DISTORTION vs FREQUENCY HD2, f = 64 MHz −70 −80 −90 HD2, f = 8 MHz HD3, f = 8 MHz 0.5 1 1.5 2 2.5 IMD VO − Output Voltage Swing − VPP Figure 7. −50 −55 −60 VO = 2 VPP Envelope −65 VO = 1 VPP Envelope −70 −75 −80 RL = 100 Ω VS = 5 V 200 kHz Tone Spacing −85 −90 10 M 100 M −50 −55 −60 VO = 2 VPP −65 Envelope −70 −75 VO = 1 VPP Envelpoe −80 −85 RL = 100 Ω VS = 5 V 200 kHz Tone Spacing −90 −95 −100 3 HD3, f = 64 MHz 2 RL = 100 Ω VS = 5 V − Third-Order Intermodulation Distortion − dBc Figure 5. − Second-Order Intermodulation Distortion − dBc Figure 4. 1G IMD SR − Slew Rate − V/ µ s 2 HARMONIC DISTORTION vs FREQUENCY 0 Harmonic Distortion − dBc RL = 100 Ω VO = 2 VPP VS = 5 V 4 HARMONIC DISTORTION vs FREQUENCY 1000 8 6 SLEW RATE vs OUTPUT VOLTAGE Fall 0 8 Figure 3. 4000 −60 10 Figure 2. 5000 −50 12 Figure 1. RL = 100 Ω VS = 5 V −40 14 f − Frequency − Hz 7000 0 16 10 f − Frequency − Hz 6000 18 Harmonic Distortion − dBc −100 100 k Large Signal Response − dB 20 Small Signal Gain − dB S-Parameter − dB 22 S21 20 −100 LARGE SIGNAL FREQUENCY RESPONSE 10 M 100 M f − Frequency − Hz f − Frequency − Hz Figure 8. Figure 9. 1G THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 TYPICAL THS4303 CHARACTERISTICS (5 V) (continued) THIRD-ORDER OUTPUT INTERCEPT vs FREQUENCY 70 49.9 −2.5V 65 Note: Add 3 dB to Reference Data to The Output of the Amplifier. 60 55 50 VO = 1 VPP Envelope RL = 100 Ω VS = 5 V 200 kHz Tone Spacing 45 40 0 50 100 150 200 250 300 f − Frequency − MHz 41 −2.5V 35 Note: Add 3 dB to Reference Data to The Output of the Amplifier. 33 31 VO = 1 VPP Envelope RL = 100 Ω VS = 5 V 200 kHz Tone Spacing 29 27 25 50 100 VO− Output Voltage − VPP 0.2 0 −0.2 −0.4 −0.6 −1 0 1 2 3 4 5 6 7 8 100 9 1k 100 k 1M Figure 12. SETTLING TIME QUIESCENT CURRENT vs SUPPLY VOLTAGE 0.2 0 −0.2 Output 40 TA = −40°C 30 25 20 15 10 0 8 9 3.25 3.5 3.75 4 4.25 4.5 4.75 5 Figure 13. Figure 14. Figure 15. OUTPUT VOLTAGE vs LOAD RESISTANCE CAPACITIVE LOAD FREQUENCY RESPONSE GAIN vs CASE TEMPERATURE 22 7 2.5 2.75 3 t − Time − ns 3 4 5 6 t − Time − ns VS = 5 V TA = −40 to 85°C 2 TA = 25°C 35 5 Input Pulse x 10 1 TA = 85°C 45 0.4 −0.4 VS − Supply Voltage − V 20.1 RL = 100 Ω VS = 5 V 20.08 20 20.06 RISO = 25 Ω, CL = 10 pF Signal Gain − dB 3.5 3 2.5 2 1.5 1 18 RISO = 15 Ω, CL = 47 pF 16 RISO= 10 Ω, CL = 100 pF 14 RISO − + 12 10 M 50 0.6 0 10 k f − Frequency − Hz −1 4 VO − Output Voltage − V 300 Figure 11. −0.8 5 4.5 250 −0.6 RL = 100 Ω VS = 5 V −0.8 200 Closed-Loop Gain − dB VO − Output Voltage − V Input Pulse x 10 0.4 150 RL = 100 Ω VS = 5 V 0.8 0.6 Vn f − Frequency − MHz 1 Output In 10 1 0 SETTLING TIME 0.8 49.9 37 Figure 10. 1 50 Test Equipment THS4303 49.9 39 Hz 50 Test Equipment 49.9 Hz 49.9 THS4303 49.9 100 Test data measurement point +2.5V 50 Source I n − Current Noise − pA/ 75 43 V n − Voltage Noise − nV/ Test data measurement point +2.5V 50 Source VOLTAGE AND CURRENT NOISE vs FREQUENCY Quiescent Current − mA 80 OIP3 − Third−Order Output Intercept Point − dBm OIP 2 − Second-Order Output Intercept Point − dBm SECOND-ORDER OUTPUT INTERCEPT vs FREQUENCY CL 0.5 20.04 VS = 5 V 20.02 20 19.98 19.96 19.94 19.92 10 0 1 19.9 RL − Load Resistance − Ω f − Frequency − Hz −40−30−20−100 10 20 30 40 50 60 70 80 90 TC − Case Temperature − °C Figure 16. Figure 17. Figure 18. 10 100 1000 1M 10 M 100 M 1G 9 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 TYPICAL THS4303 CHARACTERISTICS (5 V) (continued) REJECTION RATIOS vs CASE TEMPERATURE COMMON-MODE REJECTION RATIO vs INPUT COMMON-MODE RANGE 75 70 VS = 5 V 70 PSRR+ 60 CMMR Rejection Ratios − dB 50 CMRR 40 30 20 65 60 PSRR+ 55 50 45 10 VS = 5 V 0 100 k 1M 10 M 100 M f − Frequency − Hz 40 −40−30 −20−10 0 10 20 30 40 50 60 70 80 90 1G TC − Case Temperature − °C 50 40 30 20 10 VS = 5 V 0 −10 0 1 2 3 4 5 VICR − Input Common-Mode Voltage Range − V Figure 20. Figure 21. INPUT OFFSET VOLTAGE vs CASE TEMPERATURE POSITIVE INPUT BIAS CURRENT vs CASE TEMPERATURE SMALL-SIGNAL TRANSIENT RESPONSE 14 2.5 2 VS = 5 V 1.5 1 0.5 0 −40 −30−20−10 0 10 20 30 40 50 60 70 80 90 0.15 12 VO − Output Voltage − V I IB+ − Positive Input Bias Current − µ A VOS − Input Offset Voltage − mV 60 Figure 19. 3 10 VS = 5V 8 6 4 0.05 0 RL = 100 Ω Input tr/tf = 60 ps VS = 5 V −0.05 0 −40 −30−20−10 0 10 20 30 40 50 60 70 80 90 −0.1 0 TC − Case Temperature − °C Figure 22. Figure 23. 0.25 VS = 5 V 2 V O − Output Voltage − V 1 0.2 0.15 1.5 0.1 1 0.05 0.5 0 0 −0.05 −0.5 −1 −1 −0.1 −0.15 −1.5 RL = 100 Ω Input tr/tf = 60 ps VS = 5 V −2 −0.2 −0.25 −2.5 −1.5 −3 0 2 4 6 t − Time − ns Figure 25. 8 10 12 8 0.3 2.5 −0.5 6 OVERDRIVE RECOVERY TIME 3 0 4 Figure 24. 1.5 0.5 2 t − Time − ns LARGE-SIGNAL TRANSIENT RESPONSE VO − Output Voltage − V 0.1 2 TC − Case Temperature − °C 10 70 0 −0.3 100 200 300 400 500 600 700 800 900 1000 t − Time − ns Figure 26. VI − Input Voltage − V Rejection Ratios − dB PSRR− CMRR − Common-Mode Rejection Ratio − dB REJECTION RATIO vs FREQUENCY 10 12 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 TYPICAL THS4303 CHARACTERISTICS (5 V) (continued) POWER-DOWN QUIESCENT CURRENT vs SUPPLY VOLTAGE 0.1 1M 10 M 100 M 1G 1000 900 10 S22 0 TA = 85°C TA = 25°C 800 TA = −40°C 700 600 500 400 300 200 f − Frequency − Hz S11 −30 −40 −50 −60 −70 S12 −90 100 k VS − Supply Voltage − V Figure 27. 10 M 1M I O − Output Current Level − mA 2 RL = 100 Ω VS = 5 V 1 0.5 Input 0 1M −0.5 −1 Output −2 −1.5 −2.5 f − Frequency − Hz Figure 30. 100 M 1G 1 0 −1 −1.5 10 M 1.5 0.5 −0.5 100 k 10 G TURN-ON AND TURN-OFF TIMES DELAY TIME 1.5 RL = 100 Ω VO = 200 mV VS = 5 V 1G Figure 29. 1000 100 100 M f − Frequency − Hz Figure 28. POWER-DOWN OUTPUT IMPEDANCE vs FREQUENCY 10 VS = 5 V −20 −80 100 0 2.5 2.75 3 3.25 3.5 3.75 4 4.25 4.5 4.75 5 10 G −10 V I − Input Voltage Level − V 1 1100 Power-Down S-Parameter − dB 10 0.01 100 k POWER-DOWN S-PARAMETER vs FREQUENCY 1200 RL = 100 Ω VO = 200 mV VS = 5 V Power-Down Quiescent Current − µ A 100 Powerdown Output Impedance − Ω ZO − Closed-Loop Output Impedance − Ω CLOSED-LOOP OUTPUT IMPEDANCE vs FREQUENCY 0 −2 100 200 300 400 500 600 700 800 t − Time − ns Figure 31. 11 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 TYPICAL THS4303 CHARACTERISTICS (3 V) S-PARAMETER vs FREQUENCY SMALL SIGNAL FREQUENCY RESPONSE 40 S21 20 20 20 0 S22 −20 S11 −40 −60 S12 18 18 16 14 RL = 100 Ω VO = 100 VPP VS = 3 V 12 −80 1M 10 M 100 M 1G 1M 10 M 100 M f − Frequency − Hz 1G 1M 10 M 100 M f − Frequency − Hz 1G HARMONIC DISTORTION vs FREQUENCY SLEW RATE vs OUTPUT VOLTAGE CAPACITIVE LOAD FREQUENCY RESPONSE 2000 SR − Slew Rate − V/ µ s HD2, RL = 100 Ω −60 HD2, RL = 1 kΩ −70 22 RL = 100 Ω VS = 3 V 1800 Fall 1400 1200 Rise 1000 800 600 400 0 10 f − Frequency − MHz RISO = 25 Ω, CL = 10 pF RISO = 15 Ω, CL = 47 pF 18 RISO = 10 Ω, CL = 100 pF 16 14 RL = 100 Ω VS = 3 V 100 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 RISO − + 12 200 −90 10 G 20 1600 HD3, RL = 1 kΩ CL 10 0.8 10 M 1M VO − Output Voltage −V 100 M 1G f − Frequency − Hz Figure 35. Figure 36. Figure 37. GAIN vs CASE TEMPERATURE INPUT OFFSET VOLTAGE vs CASE TEMPERATURE POSITIVE INPUT BIAS CURRENT vs CASE TEMPERATURE 1.5 14 20.04 VS = 3 V 20 19.98 19.96 19.94 19.92 19.9 −40−30−20−10 0 10 20 30 40 50 60 70 80 90 Case Temperature − °C Figure 38. VOS − Input Offset Voltage − mV 20.06 1.25 1 VS = 3 V 0.75 0.5 0.25 0 −40−30−20−10 0 10 20 30 40 50 60 70 80 90 TC − Case Temperature − °C Figure 39. I IB − Posaitive Input Bias Current − µ A 20.08 Closed-Loop Gain − dB RL = 100 Ω VO = 1 VPP VS = 3 V 100 k 10 G −80 12 6 Figure 34. HD3 RL = 100 Ω 20.02 8 Figure 33. −50 1 10 Figure 32. VO = 0.5 VPP VS = 3 V −40 12 0 100 k f − Frequency − Hz −30 14 2 10 10 G 16 4 Signal Gain − dB −100 100 k Large Signal Gain − dB Small Signal Gain − dB S-Parameter − dB 22 22 VS = 3 V Harmonic Distortion − dBc LARGE SIGNAL FREQUENCY RESPONSE VS = 3 V 12 10 8 6 4 2 0 −40−30−20−10 0 10 20 30 40 50 60 70 80 90 TC − Case Temperature − °C Figure 40. THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 TYPICAL THS4303 CHARACTERISTICS (3 V) (continued) POWER-DOWN S-PARAMETER vs FREQUENCY OVERDRIVE RECOVERY TIME VS = 3 V 10 0.15 0 S22 0.1 1 0.5 0.05 0 0 −0.5 −0.05 −1 −0.1 −1.5 −0.15 −2 0 −0.2 100 200 300 400 500 600 700 800 900 1000 t − Time − ns Figure 41. VI − Input Voltage − V VO − Output Voltage − V 1.5 0.2 Power-Down S-Parameter − dB 2 −10 VS = 3 V −20 S11 −30 −40 −50 −60 −70 S12 −80 −90 100 k 1M 10 M 100 M 1G 10 G f − Frequency − Hz Figure 42. 13 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 APPLICATION INFORMATION HIGH-SPEED OPERATIONAL AMPLIFIERS The THS4303 fixed gain operational amplifier set new performance levels, combining low distortion, high slew rates, low noise, and a gain bandwidth in excess of 1.8 GHz. To achieve the full performance of the amplifier, careful attention must be paid to printed-circuit board layout and component selection. equipment, provides a 100-Ω load. The total 100-Ω load at the output, combined with the 500-Ω total feedback network load, presents the THS4303 with an effective output load of 83 Ω for the circuit of Figure 43. INTERNAL FIXED RESISTOR VALUES In addition, the devices provide a power-down mode with the ability to save power when the amplifier is inactive. APPLICATIONS SECTION CONTENTS • Wideband, Noninverting Operation • Single Supply Operation • Saving Power With Power-Down Functionality • Driving an ADC With the THS4303 • Driving Capacitive Loads • Power Supply Decoupling Techniques and Recommendations • Board Layout • Printed-Circuit Board Layout Techniques for Optimal Performance • PowerPAD Design Considerations • PowerPAD PCB Layout Considerations • Thermal Analysis • Design Tools • Evaluation Fixtures and Application Support Information • Additional Reference Material • Mechanical Package Drawings WIDEBAND, NONINVERTING OPERATION The THS4303 is a fixed gain voltage feedback operational amplifier, with power-down capability, designed to operate from a single 3-V to 5-V power supply. Figure 43 is the noninverting gain configuration used to demonstrate the typical performance curves. Most of the curves were characterized using signal sources with 50-Ω source impedance, and with measurement equipment presenting a 50-Ω load impedance. In Figure 43, the 49.9-Ω shunt resistor at the VIN terminal matches the source impedance of the test generator. The 50-Ω series resistor at the VO terminal in addition to the 50-Ω load impedance of the test 14 DEVICE GAIN (V/V) Rf Rg THS4303 +10 450 50 VS+ + FB 22 µF 0.1 µF 47 pF 30.1 Ω Rf Rg 50 Ω Source 50 Ω Load _ + VI THS4303 49.9 Ω VO 49.9 Ω VS− + 22 µF FB 47 pF 0.1 µF 30.1 Ω FB = Ferrite Bead Figure 43. Wideband, Noninverting Gain Configuration THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 SINGLE SUPPLY OPERATION The THS4303 is designed to operate from a single 3-V to 5-V power supply. When operating from a single power supply, care must be taken to ensure the input signal and amplifier are biased appropriately to allow for the maximum output voltage swing. The circuits shown in Figure 44 demonstrate methods to configure an amplifier in a manner conducive for single supply operation. VS+ + FB 22 µF 47 pF 0.1 µF Rg *2.5 V VI _ + THS4303 50 Ω Load The THS4303 amplifier can be used to drive high-performance analog-to-digital converters. Two example circuits are presented below. 49.9 Ω VO *2.5 V FB = Ferrite Bead * = Low Impedance Figure 44. DC-Coupled Single Supply Operation WITH APPLICATION CIRCUITS DRIVING AN ANALOG-TO-DIGITAL CONVERTER WITH THE THS4303 49.9 Ω SAVING POWER FUNCTIONALITY The time delays associated with turning the device on and off are specified as the time it takes for the amplifier to reach 50% of the nominal quiescent current. The time delays are on the order of microseconds because the amplifier moves in and out of the linear mode of operation in these transitions. 30.1 Ω Rf 50 Ω Source the impedance looking back into the output of the amplifier is dominated by the feedback and gain setting resistors, but the output impedance of the device itself varies depending on the voltage applied to the outputs. POWER-DOWN The first circuit uses a wideband transformer to convert a single-ended input signal into a differential signal. The amplified signal from the output of the THS4303 is fed through a low-pass filter, via an isolation resistor and an ac-coupling capacitor, to the transformer. For applications without signal content at dc, this method of driving ADCs is very useful. Where dc information content is required, the THS4500 family of fully differential amplifiers may be applicable. VS+ The THS4303 features a power-down pin (PD) which lowers the quiescent current from 34 mA down to 1 mA, ideal for reducing system power. The power-down pin of the amplifier defaults to the positive supply voltage in the absence of an applied voltage, putting the amplifier in the power-on mode of operation. To turn off the amplifier in an effort to conserve power, the power-down pin can be driven towards the negative rail. The threshold voltages for power-on and power-down are relative to the supply rails and given in the specification tables. Above the Enable Threshold Voltage, the device is on. Below the Disable Threshold Voltage, the device is off. Behavior in between these threshold voltages is not specified. Note that this power-down functionality is just that; the amplifier consumes less power in power-down mode. The power-down mode is not intended to provide a high- impedance output. In other words, the power-down functionality is not intended to allow use as a 3-state bus driver. When in power-down mode, + FB 22 µF 0.1 µF 47 pF 30.1 Ω Rf Rg 50 Ω Source _ + *2.5 V VI THS4303 49.9 Ω *2.5 V RISO C R IN ADC FB = Ferrite Bead * = Low Impedance R IN CM Figure 45. Driving an ADC Via a Transformer 15 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 The second circuit depicts single-ended ADC drive. While not recommended for optimum performance using converters with differential inputs, satisfactory performance can sometimes be achieved with singleended input drive. An example circuit is shown here for reference. VS+ + FB 22 µF 0.1 µF 47 pF 30.1 Ω Rf Rg 50 Ω Source _ + *2.5 V VI THS4303 sponse flatness, pulse response fidelity, or distortion, the simplest and most effective solution is to isolate the capacitive load from the feedback loop by inserting a series isolation resistor between the amplifier output and the capacitive load. The Typical Characteristics show the recommended isolation resistor vs capacitive load and the resulting frequency response at the load. Parasitic capacitive loads greater than 2 pF can begin to degrade the performance of the THS4303. Long PC board traces, unmatched cables, and connections to multiple devices can easily cause this value to be exceeded. Always consider this effect carefully, and add the recommended series resistor as close as possible to the THS4303 output pin (see Board Layout Guidelines). The criterion for setting this R(ISO) resistor is a maximum bandwidth, flat frequency response at the load. 49.9 Ω *2.5 V FB = Ferrite Bead * = Low Impedance 22 RISO C RL = 100 Ω VS = 5 V 20 RISO = 25 Ω, CL = 10 pF C CM IN R ADC C Figure 46. Driving an ADC With a Single-Ended Input Signal Gain − dB IN 18 RISO = 15 Ω, CL = 47 pF 16 RISO= 10 Ω, CL = 100 pF 14 RISO − + 12 CL 10 1M 10 M 100 M 1G f − Frequency − Hz NOTE: For best performance, high-speed ADCs should be driven differentially. See the THS4500 family of devices for more information. DRIVING CAPACITIVE LOADS One of the most demanding, and yet very common, load conditions for an op amp is capacitive loading. Often, the capacitive load is the input of an A/D converter, including additional external capacitance, which may be recommended to improve A/D linearity. High-speed amplifiers like the THS4303 can be very susceptible to decreased stability and closed-loop response peaking when a capacitive load is placed directly on the output pin. When the amplifier's open-loop output resistance is considered, this capacitive load introduces an additional pole in the signal path that can decrease the phase margin. When the primary considerations are frequency re- 16 Figure 47. Driving Capacitive Loads POWER SUPPLY DECOUPLING TECHNIQUES AND RECOMMENDATIONS Power supply decoupling is a critical aspect of any high-performance amplifier design process. Careful decoupling provides higher quality ac performance (most notably improved distortion performance). The following guidelines ensure the highest level of performance. 1. Place decoupling capacitors as close to the power supply inputs as possible, with the goal of minimizing the inductance of the path from ground to the power supply. Inductance in series with the bypass capacitors will degrade performance. Note that a narrow lead or trace has about 0.8 nH of inductance for every millimeter of length. Each printed-circuit board (PCB) via also has between 0.3 and 0.8 nH depending on length and diameter. For these reasons, it is recommended to use a power supply trace about the width of the package for each power supply lead THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 to the caps, and 3 or more vias to connect the caps to the ground plane. 2. Placement priority should put the smallest valued capacitors closest to the device. 3. Solid power planes can lead to PCB resonances when they are not properly terminated to the ground plane over the area and along the perimeter of the power plane by high frequency capacitors. Doing so assures that there are no power plane resonances in the needed frequency range. Values used are in the range of 2 pF - 50 pF, depending on the frequencies to be suppressed, with numerous vias for each. 4. Using 0402 or smaller component sizes is recommended. An approximate expression for the resonate frequencies associated with a length of one of the power plane dimensions is given in equation (1). Note that a power plane of arbitrary shape can have a number of resonant frequencies. A power plane without distributed capacitors and with active parts near the center of the plane usually has n even (≥2) due to the half wave resonant nature of the plane. frequency res n (44 GHz mm) where: frequencyres = the approximate power plane resonant frequencies in GHz = the length of the power plane dimensions in millimeters n = an integer (n > 1) related to the mode of the oscillation • For guidance on capacitor spacing over the area of the ground plane, specify the lowest resonant frequency to be tolerated, then solve for in equation (1) above, with n = 2. Use this length for the capacitor spacing. It is recommended that a power plane, if used, be either small enough, or decoupled as described, so that there are no resonances in the frequency range of interest. An alternative is to use a ferrite bead outside of the opamp high frequency bypass caps to decouple the amplifier, and mid and high frequency bypass capacitors, from the power plane. When a trace is used to deliver power, its self-resonance is given approximately by equation (1), substituting the trace length for power plane dimension. 1. Bypass capacitors, since they have a self-inductance, resonate with each other. To achieve optimum transfer characteristics through 2 GHz, it is recommended that the bypass arrangement employed in the prototype board be used. The 30.1-Ω resistor in series with the 0.1-µF capacitor reduces the Q of the resonance of the lumped parallel elements including the 0.1-µF and 47-pF capacitors, and the power supply input of the amplifier. The ferrite bead isolates the low frequency 22-µF capacitor and power plane from the remainder of the bypass network. 2. By removing the 30.1-Ω resistor and ferrite bead, the frequency response characteristic above 400 MHz may be modified. However, bandwidth, distortion, and transient response remain optimal. 3. Recommended values for power supply decoupling include a bulk decoupling capacitor (22 µF), a ferrite bead with a high self-resonant frequency, a mid-range decoupling capacitor (0.1 µF) in series with a 30.1-Ω resistor, and a high frequency decoupling capacitor (47 pF). BOARD LAYOUT Printed-Circuit Board Layout Techniques for Optimal Performance Achieving optimum performance with a high frequency amplifier like the THS4303 requires careful attention to board layout parasitics and external component types. Recommendations that optimize performance include: 1. Minimize parasitic capacitance to any ac ground for all of the signal I/O pins. However, if using a transmission line at the I/O, then place the matching resistor as close to the part as possible. Except for when transmission lines are used, parasitic capacitance on the output and the noninverting input pins can react with the load and source impedances to cause unintentional band limiting. To reduce unwanted capacitance, a window around the signal I/O pins should be opened in all of the ground and power planes around those pins. Otherwise, ground planes and power planes (if used) should be unbroken elsewhere on the board, and terminated as described in the Power Supply Decoupling section. 2. Minimize the distance (< 0.25”) from the power supply pins to high frequency 0.1-µF decoupling capacitors. At the device pins, the ground and power plane layout should not be in close proximity to the signal I/O pins. Avoid narrow power and ground traces to minimize inductance between the pins and the decoupling capacitors. Note that each millimeter of a line, that is narrow relative to its length, has ~ 0.8 nH of inductance. The power supply connections should always be decoupled with the recommended capacitors. If not properly decoupled, distortion performance is degraded. Larger (6.8-µF to 22-µF) decoupling capacitors, effective at lower frequency, should also be used on the main supply lines, preferably decoupled from the amplifier and mid and high frequency capacitors by a ferrite bead. Reference the Power Supply Decoupling Techniques section. The larger caps may be placed somewhat farther from the device 17 THS4303 SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 and may be shared among several devices in the same area of the PC board. A very low inductance path should be used to connect the inverting pin of the amplifier to ground. A minimum of 5 vias as close to the part as possible is recommended. 3. Careful selection and placement of external components preserves the high frequency performance of the THS4303. Resistors should be a very low reactance type. Surface-mount resistors work best and allow a tighter overall layout. Axially-leaded parts do not provide good high frequency performance, since they have ~ 0.8 nH of inductance for every mm of current path length. Again, keep PC board trace length as short as possible. Never use wirewound type resistors in a high frequency application. Since the output pin and inverting input pin are the most sensitive to parasitic capacitance, always position the terminating resistors, if any, as close as possible to the noninverting and output pins. Even with a low parasitic capacitance shunting the external resistors, excessively high resistor values can create significant time constants that can degrade performance. Good axial metal-film or surface-mount resistors have approximately 0.2 pF in shunt with the resistor. 4. Connections to other wideband devices on the board may be made with short direct traces or through onboard transmission lines. For short connections, consider the trace and the input to the next device as a lumped capacitive load. Relatively wide traces (50 mils to 100 mils) should be used, preferably with ground and power planes opened up around them. Estimate the total capacitive load and set RISO from the plot of recommended RISO vs Capacitive Load. Low parasitic capacitive loads (<4 pF) may not need an RISO since the THS4303 is nominally compensated to operate with a 2 pF parasitic load. Higher parasitic capacitive loads without an RISO are allowed as the signal gain increases (increasing the unloaded phase margin). If a long trace is required, and the 6 dB signal loss intrinsic to a doubly-terminated transmission line is acceptable, implement a matched impedance transmission line using microstrip or stripline techniques (consult an ECL design handbook for microstrip and stripline layout techniques). With a characteristic board trace impedance defined based on board material and trace dimensions, a matching series resistor into the trace from the output of the THS4303 is used as well as a terminating shunt resistor at the input of the destination device. Remember also that the terminating impedance is the parallel combination of the shunt resistor and the input impedance of the 18 www.ti.com destination device: this total effective impedance should be set to match the trace impedance. If the 6 dB attenuation of a doubly terminated transmission line is unacceptable, a long trace can be series-terminated at the source end only. Treat the trace as a capacitive load in this case and set the series resistor value as shown in the plot of RISO vs Capacitive Load. This does not preserve signal integrity as well as a doubly-terminated line. If the input impedance of the destination device is low, there is some signal attenuation due to the voltage divider formed by the series output into the terminating impedance. A 50-Ω environment is normally not necessary on board as long as the lead lengths are short, and in fact, a higher impedance environment improves distortion as shown in the distortion versus load plots. Uncontrolled impedance traces without double termination results in reflections at each end, and hence, produces PCB resonances. It is recommended that if this approach is used, the trace length be kept short enough to avoid resonances in the band of interest. For guidance on useful lengths, use equation (1) given in the Power Supply Decoupling Techniques section for approximate resonance frequencies verses trace length. This relation provides an upper bound on the resonant frequency, because additional capacitive coupling to the trace from other leads or the ground plane causes extra distributed loading and slows the signal propagation along the trace. 5. Socketing a high-speed part like the THS4303 is not recommended. The additional lead length inductance and pin-to-pin capacitance introduced by the socket creates an extremely troublesome parasitic network, which can make it almost impossible to achieve a smooth, stable frequency response. Best results are obtained by soldering the THS4303 onto the board. PowerPAD™ DESIGN CONSIDERATIONS The THS4303 is available in a thermally-enhanced PowerPAD family of packages. These packages are constructed using a downset leadframe upon which the die is mounted [see Figure 48(a) and Figure 48(b)]. This arrangement results in the lead frame being exposed as a thermal pad on the underside of the package [see Figure 48(c)]. Because this thermal pad has direct thermal contact with the die, excellent thermal performance can be achieved by providing a good thermal path away from the thermal pad. The PowerPAD package allows both assembly and thermal management in one manufacturing operation. THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 During the surface-mount solder operation (when the leads are being soldered), the thermal pad can also be soldered to a copper area underneath the package. Through the use of thermal paths within this copper area, heat can be conducted away from the package into either a ground plane or other heat dissipating device. The PowerPAD package represents a breakthrough in combining the small area and ease of assembly of surface mount with the heretofore awkward mechanical methods of heatsinking. 4. 5. DIE Side View (a) DIE End View (b) Bottom View (c) Figure 48. Views of Thermally Enhanced Package Although there are many ways to properly heatsink the PowerPAD package, the following steps illustrate the recommended approach. 6. 0.144 0.049 7. 0.012 Pin 1 0.0095 0.015 0.144 0.0195 0.0705 0.010 vias 0.032 0.030 0.0245 Top View Figure 49. PowerPAD PCB Etch and Via Pattern PowerPAD PCB LAYOUT CONSIDERATIONS 1. Prepare the PCB with a top side etch pattern as shown in Figure 49. There should be etch for the leads as well as etch for the thermal pad. 2. Place five holes in the area of the thermal pad. They holes should be 13 mils in diameter. Keep them small so that solder wicking through the holes is not a problem during reflow. 3. Additional vias may be placed anywhere along the thermal plane outside of the thermal pad 8. area. They help dissipate the heat generated by the IC. These additional vias may be larger than the 13-mil diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad area to be soldered, so that wicking is not a problem. Connect all holes to the internal ground plane. When connecting these holes to the ground plane, do not use the typical web or spoke via connection methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat transfer during soldering operations. This resistance makes the soldering of vias that have plane connections easier. In this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore, the holes under the IC PowerPAD package should make their connection to the internal ground plane, with a complete connection around the entire circumference of the plated-through hole. The top-side solder mask should leave the terminals of the package and the thermal pad area with its five holes exposed. The bottom-side solder mask should cover the five holes of the thermal pad area. This prevents solder from being pulled away from the thermal pad area during the reflow process. Apply solder paste to the exposed thermal pad area and all of the IC terminals. With these preparatory steps in place, the IC is simply placed in position and run through the solder reflow operation as any standard surface-mount component. This results in a part that is properly installed. The next consideration is the package constraints. The two sources of heat within an amplifier are quiescent power and output power. The designer should never forget about the quiescent heat generated within the device, especially multi-amplifier devices. Because these devices have linear output stages (Class AB), most of the heat dissipation is at low output voltages with high output currents. The other key factor when dealing with power dissipation is how the devices are mounted on the PCB. The PowerPAD devices are extremely useful for heat dissipation. But, the device should always be soldered to a copper plane to fully use the heat dissipation properties of the PowerPAD. The SOIC package, on the other hand, is highly dependent on how it is mounted on the PCB. As more trace and copper area is placed around the device,Θ JA decreases and the heat dissipation capability increases. For a single package, the sum of the RMS output currents and voltages should be used to choose the proper package. 19 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 THERMAL ANALYSIS The THS4303 device does not incorporate automatic thermal shutoff protection, so the designer must take care to ensure that the design does not violate the absolute maximum junction temperature of the device. Failure may result if the absolute maximum junction temperature of 150° C is exceeded. The thermal characteristics of the device are dictated by the package and the PC board. For a given ΘJA, maximum power dissipation for a package can be calculated using the following formula. P Dmax Tmax–T A JA where: PDmax is the maximum power dissipation in the amplifier (W). Tmax is the absolute maximum junction temperature (°C). TA is the ambient temperature (°C). θJA = θJC + θCA θJC is the thermal coefficient from the silicon junctions to the case (°C/W). θCA is the thermal coefficient from the case to ambient air (°C/W). The THS4303 is offered in a 16-pin leadless MSOP with PowerPAD. The thermal coefficient for the MSOP PowerPAD package is substantially improved over the traditional packages. Maximum power dissipation levels are depicted in the graph below. The data for the RGT package assumes a board layout that follows the PowerPAD layout guidelines referenced above and detailed in the PowerPAD application notes in the Additional Reference Material section at the end of the data sheet. PD − Maximum Power Dissipation − W 7 6 5 16-Pin RGT Package 4 3 2 1 0 −40 −20 0 20 40 60 TA − Ambient Temperature − °C 80 θJA = 39.5°C/W for 16-Pin MSOP (RGT) TJ = 150°C, No Airflow Figure 50. Maximum Power Dissipation vs Ambient Temperature When determining whether or not the device satisfies the maximum power dissipation requirement, it is 20 important to consider not only quiescent power dissipation, but also dynamic power dissipation. Often maximum power is difficult to quantify because the signal pattern is inconsistent, but an estimate of the RMS power dissipation can provide visibility into a possible problem. DESIGN TOOLS Evaluation Fixtures Information and Application Support Texas Instruments is committed to providing its customers with the highest quality of applications support. To support this goal, an evaluation board has been developed for the THS4303 operational amplifier. The evaluation board is available and easy to use allowing for straight-forward evaluation of the device. These evaluation board can be obtained by ordering through the Texas Instruments web site, www.ti.com, or through your local Texas Instruments Sales Representative. A schematic for the evaluation board is shown in Figure 51 with their default component values. Unpopulated footprints are shown to provide insight into design flexibility Computer simulation of circuit performance using SPICE is often useful when analyzing the performance of analog circuits and systems. This is particularly true for video and RF amplifier circuits where parasitic capacitance and inductance can have a major effect on circuit performance. A SPICE model for the THS4303 device is available through the Texas Instruments web site at www.ti.com. The Product Information Center (PIC) is also available for design assistance and detailed product information. These models do a good job of predicting small-signal ac and transient performance under a wide variety of operating conditions. They are not intended to model the distortion characteristics of the amplifier, nor do they attempt to distinguish between the package types in their small-signal ac performance. Detailed information about what is and is not modeled is contained in the model file itself. THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 VS+ FB2 J3 C2 22 µF + 13 NC 14 47 pF C4 0.1 µF R5 30.1 Ω 9 _ + PD J6 A Rf Rg J1 R4 49.9 Ω C9 * 6454762 12 11 10 VI C6 U1 8 7 6 5 R2 49.9 Ω 16 J2 VO R3 * C1 1 2 1 µF VS− 3 C7 * J4 C3 22 µF 4 + C8 47 pF FB1 C5 0.1 µF R4 30.1 Ω * = Not populated Figure 51. Typical THS4303 EVM Circuit Configuration Figure 52. THS4303EVM Layout (Top Layer and Silkscreen Layer) Figure 53. THS4303EVM Board Layout (Ground Layers 2 and 3) Figure 54. THS4303EVM Board Layout (Bottom Layer) 21 THS4303 www.ti.com SLOS421B – NOVEMBER 2003 – REVISED JANUARY 2005 BILL OF MATERIALS THS4303RGT EVM ITEM (1) DESCRIPTION SMD SIZE REFERENCE DESIGNATOR PCB QUANTITY MANUFACTURER'S PART NUMBER (1) 1206 FB1, FB2 2 (Steward) HI1206N800R-00 D C2, C3 2 (AVX) TAJD226K025R (AVX) 08053G105ZAT2A 1 Bead, ferrite, 3 A, 80 Ω 2 Capacitor 22 µF, tantalum, 25 V, 10% 3 Capacitor 1 µF, ceramic, 25 V, Y5V 0805 C1 1 4 Open 0402 C6, C7 2 5 Capacitor 47 pF, ceramic, 50 V, NPO 0402 C8, C9 2 (AVX) 04025A470JAT2A 6 Capacitor 0.1 µF, ceramic, 16 V, X7R 0603 C4, C5 2 (AVX) 0603YC104KAT2A 7 Resistor, 30.1 Ω, 1/16 W, 1% 0402 R4, R5 2 (KOA) RK73H1E30R1F 8 Open 0603 R3 1 0603 9 Resistor, 49.9 Ω, 1/16 W, 1% 10 Jack, banana receptance, 0.25” dia. hole 11 Test point, red 12 Test point, black 13 Connector, edge, SMA PCB jack 14 IC THS4303 15 Standoff, 4-40 hex, 0.625” length 4 (Keystone) 1808 16 Screw, phillips, 4-40, .250” 4 SHR-0440-016-SN 17 Board, printed-circuit 1 (TI) EDGE # 6454762 Rev. A R1, R2 2 (Phycomp) 9C06031A49R9FKRFT J3, J4, J5 3 (HH Smith) 101 (Keystone) 5000 J6 1 TP1 1 (Keystone) 5001 J1, J2 2 (Johnson) 142-0701-801 U1 1 (TI) THS4303RGT The manufacturer's part numbers are used for test purposes only. ADDITIONAL REFERENCE MATERIAL • • PowerPAD Made Easy, application brief (SLMA004) PowerPAD Thermally Enhanced Package, technical brief (SLMA002) EVM WARNINGS AND RESTRICTIONS It is important to operate this EVM within the input and output voltage ranges as specified in the table provided below. Input Range, VS+ to VS– 3.0 V to 6.0 V Input Range, VI 3.0 V to 6.0 V NOT TO EXCEED VS+ or VS– Output Range, VO 3.0 V to 6.0 V NOT TO EXCEED VS+ or VS– Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions concerning the input range, please contact a TI field representative prior to connecting the input power. Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM. Please consult the product data sheet or EVM user's guide (if user's guide is available) prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures greater than 30°C. The EVM is designed to operate properly with certain components above 50°C as long as the input and output ranges are maintained. These components include but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified using the EVM schematic located in the material provided. When placing measurement probes near these devices during operation, please be aware that these devices may be very warm to the touch. Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 22 PACKAGE OPTION ADDENDUM www.ti.com 30-Mar-2005 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty THS4303RGTR ACTIVE QFN RGT 16 3000 TBD CU NIPDAU Level-2-220C-1 YEAR THS4303RGTT ACTIVE QFN RGT 16 250 TBD CU NIPDAU Level-2-220C-1 YEAR Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DSP dsp.ti.com Broadband www.ti.com/broadband Interface interface.ti.com Digital Control www.ti.com/digitalcontrol Logic logic.ti.com Military www.ti.com/military Power Mgmt power.ti.com Optical Networking www.ti.com/opticalnetwork Microcontrollers microcontroller.ti.com Security www.ti.com/security Telephony www.ti.com/telephony Video & Imaging www.ti.com/video Wireless www.ti.com/wireless Mailing Address: Texas Instruments Post Office Box 655303 Dallas, Texas 75265 Copyright 2005, Texas Instruments Incorporated