TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 D D D D D D D D D DW OR N PACKAGE (TOP VIEW) 8-Bit Resolution A/D Converter Microprocessor Peripheral or Stand-Alone Operation On-Chip 12-Channel Analog Multiplexer Built-In Self-Test Mode Software-Controllable Sample and Hold Total Unadjusted Error . . . ± 0.5 LSB Max Direct Replacement for Motorola MC145041 Onboard System Clock End-of-Conversion (EOC) Output Pinout and Control Signals Compatible With the TLC1542/3 10-Bit A/D Converters CMOS Technology PARAMETER VALUE Channel Acquisition/Sample Time 16 µs Conversion Time (Max) 20 µs INPUT A0 INPUT A1 INPUT A2 INPUT A3 INPUT A4 INPUT A5 INPUT A6 INPUT A7 INPUT A8 GND Power Dissipation (Max) 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC EOC I/O CLOCK ADDRESS INPUT DATA OUT CS REF+ REF– INPUT A10 INPUT A9 FN PACKAGE (TOP VIEW) 25 × 103 Samples per Second (Max) 1 INPUT A2 INPUT A1 INPUT A0 VCC EOC D D INPUT A3 INPUT A4 INPUT A5 INPUT A6 INPUT A7 10 mW description 4 3 2 1 20 19 18 5 17 6 16 7 15 I/O CLOCK ADDRESS INPU DATA OUT CS REF+ INPUT A8 GND INPUT A9 INPUT A10 REF– The TLC542 is a CMOS converter built around an 14 8 8-bit switched-capacitor successive-approximation 9 10 11 12 13 analog-to-digital converter. The device is designed for serial interface to a microprocessor or peripheral via a 3-state output with three inputs [including I/O CLOCK, CS (chip select), and ADDRESS INPUT]. The TLC542 allows high-speed data transfers and sample rates of up to 40,000 samples per second. In addition to the high-speed converter and versatile control logic, an on-chip 12-channel analog multiplexer can sample any one of 11 inputs or an internal self-test voltage, and the sample and hold is started under microprocessor control. At the end of conversion, the end-ofconversion (EOC) output pin goes high to indicate that conversion is complete. The converter incorporated in the TLC542 features differential high-impedance reference inputs that facilitate ratiometric conversion, scaling, and isolation of analog circuitry from logic and supply noises. A switchedcapacitor design allows low-error (± 0.5 LSB) conversion in 20 µs over the full operating temperature range. The TLC542C is characterized for operation from 0°C to 70°C and the TLC542I is characterized for operation from – 40°C to 85°C. AVAILABLE OPTIONS PACKAGE TA CHIP CARRIER (FN) 0°C to 70°C — TLC542CN TLC542CDW – 40°C to 85°C TLC542IFN TLC542IN TLC542IDW PLASTIC DIP (N) SMALL OUTLINE (DW) Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2001, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 functional block diagram REF+ 8-Bit Analog-to-Digital Converter (Switched-Capacitors) Sample and Hold 8 12-Channel Analog Multiplexer Analog Inputs REF– 4 Output Data Register Input Address Register 8 8-to-1 Data Selector and Driver DATA OUT 4 Self-Test Reference 4 Input Multiplexer ADDRESS INPUT Control Logic and I/O Counters 2 I/O CLOCK CS EOC typical equivalent inputs INPUT CIRCUIT IMPEDANCE DURING SAMPLING MODE INPUT CIRCUIT IMPEDANCE DURING HOLD MODE 1 kΩ TYP INPUT A0 – A10 2 INPUT A0 – A10 Ci = 60 pF TYP (equivalent input capacitance) POST OFFICE BOX 655303 5 MΩ TYP • DALLAS, TEXAS 75265 TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 operating sequence 1 2 3 4 5 6 7 8 I/O CLOCK 1 2 3 4 5 6 7 8 Don’t Care Access Cycle B (see Note A) tsu(A) tacq Access Cycle C tc(1) t(acq) 12 Internal System Clocks ≤ 12 µs tsu(CS) CS MSB ADDRESS INPUT B3 LSB B2 B1 MSB Don’t Care B0 C3 LSB C2 C1 Don’t Care C0 Hi-Z State Hi-Z State DATA OUT A7 A6 A5 A4 A3 A2 A1 A0 B7 B6 B5 B4 B3 B2 B1 B0 See Note B Previous Conversion Data A MSB LSB (see Note B) td(I/O–EOC) Conversion Data B td(EOC–DATA) MSB LSB EOC tc(2) NOTES: A. To minimize errors caused by noise at the chip select input, the internal circuitry waits for two rising edges and one falling edge of the internal system clock after CS↓ before responding to control input signals. The CS setup time is given by the tsu(CS) specifications. Therefore, no attempt should be made to clock-in an address until the minimum chip select setup time has elapsed. B. The output becomes 3-state on CS going high or on the negative edge of the eighth I/O clock. absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage, VCC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 V Input voltage range (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to VCC + 0.3 V Output voltage range, VO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to VCC + 0.3 V Peak input current range (any input), Ip-p) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±20 mA Peak total input current (all inputs), IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±30 mA Operating free-air temperature range: TLC542C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C TLC542l . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 40°C to 85°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C Case temperature for 10 seconds, TC: FN package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: DW or N package . . . . . . . . . . . . . . 260°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values are with respect to digital ground with REF– and GND wired together (unless otherwise noted). POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 3 TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 recommended operating conditions, VCC = 4.75 to 5.5 V MIN NOM MAX 4.75 5 5.5 V Vref– – 0.1 VCC 0 VCC + 0.1 Vref+ V Differential reference voltage, Vref+ – Vref– (see Note 2) 1 VCC Analog input voltage (see Note 3) 0 High-level control input voltage, VIH 2 Supply voltage, VCC Positive reference voltage, Vref + (see Note 2) Negative reference voltage, Vref – (see Note 2) UNIT VCC + 0.2 VCC V V V Low-level control input voltage, VIL 0.8 Setup time, address bits at data input before I/O CLOCK↑, tsu(A) V V 400 ns Hold time, address bits after I/O CLOCK↑, th(A) 0 ns Hold time, CS low after 8th I/O CLOCK↑, th(CS) 0 ns 3.8 µs Setup time, CS low before clocking in first address bit, tsu(CS) (see Note 4) Input/output clock frequency, f(clock I/O) 0 Input/output clock high, tw(H I/O) 1.1 MHz 404 Input/output clock low, tw(L I/O) ns 404 I/O CLOCK transition time, time tt (see Note 3) 100 ns 40 TLC542C Operating free-air free air temperature, temperature TA ns fclock(I/O) ≤ 525 kHz fclock(I/O) > 525 kHz TLC542I 0 70 – 40 85 °C NOTES: 2. Analog input voltages greater than that applied to REF+ convert as all ones (11111111), while input voltages less than that applied to REF – convert as all zeros (00000000). For proper operation, REF+ must be at least 1 V higher than REF –. Also, the total unadjusted error may increase as this differential reference voltage falls below 4.75 V. 3. This is the time required for the clock input signal to fall from VIH min to VIL max or to rise from VIL max to VIH min. In the vicinity of normal room temperature, the devices function with input clock transition time as slow as 2 µs for remote data acquisition applications where the sensor and the A/D converter are placed several feet away from the controlling microprocessor. 4. To minimize errors caused by noise at the chip select input, the internal circuitry waits for two rising edges and one falling edge of the internal system clock after CS ↓ before responding to control input signals. The CS setup time is given by the tsu(CS) specifications. Therefore, no attempt should be made to clock-in address data until the minimum chip select setup time has elapsed. electrical characteristics over recommended operating temperature range, VCC = Vref+ = 4.75 V to 5.5 V, f(clock I/O) = 1.1 MHz (unless otherwise noted) PARAMETER VOH VOL TEST CONDITIONS High-level output voltage (DATA OUT) Low-level output voltage Off state (high-impedance Off-state (high impedance state) output current MIN TYP† MAX VCC = 4.75 V, VCC = 4.75 V, IOH = – 360 µA IOL = 1.6 mA VO = VCC, VO = 0, CS at VCC 10 CS at VCC –10 2.4 UNIT V 0.4 V µA IIH IIL High-level input current VI = VCC VI = 0 0.005 2 µA Low-level input current – 0.005 – 2.5 µA ICC Operating supply current CS at 0 V 1.2 2 mA Selected channel at VCC and unselected channel at 0 V Selected channel leakage current µA Selected channel at 0 V and unselected channel at VCC Iref Maximum static analog reference current into REF+ Ci Input capacitance Vref+ = VCC, – 0.4 Vref – = GND 10 Analog inputs 7 55 Control inputs 5 15 † All typical values are at TA = 25°C. 4 0.4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 µA pF TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 operating characteristics over recommended operating free-air temperature range, VCC = Vref + = 4.75 to 5.5 V, f(clock I/O) = 1 MHZ PARAMETER EL EZS Linearity error (see Note 5) Zero-scale error (see Note 6) EFS Full-scale error (see Note 6) TEST CONDITIONS MIN TYP† MAX UNIT ±0.5 LSB See Note 2 ±0.5 LSB See Note 2 ±0.5 LSB ±0.5 LSB Total unadjusted error (see Note 7) Self-test output code Input A11 address = 1011, See Note 8 01111101 (126) tc(1) tc(2) Conversion time See operating sequence 20 µs Total access and conversion cycle time See operating sequence 40 µs t(acq) t(v) Channel acquisition time (sample cycle) See operating sequence 16 µs Time output data remains valid after I/O CLK↓ See Figure 5 td(IO-DATA) td(IO-EOC) Delay time, I/O CLK↓ to data output valid See Figure 5 400 ns Delay time, 8th I/O CLK↓ to EOC↓ See Figure 6 500 ns td(EOC-DATA) tPZH, tPZL Delay time, EOC↑ to data out (MSB) See Figure 7 400 ns Delay time, CS↓ to data out (MSB) See Figure 2 3.4 µs tPHZ, tPLZ tr(EOC) Delay time, CS↑ to data out (MSB) See Figure 2 150 ns Rise time See Figure 7 100 ns tf(EOC) tr(bus) Fall time See Figure 6 100 ns Data bus rise time See Figure 5 300 ns 128 10000011 (130) 10 ns tf(bus) Data bus fall time See Figure 5 300 ns † All typical values are at TA = 25°C. NOTES: 2. Analog input voltages greater than that applied to REF + convert to all ones (11111111), while input voltages less than that applied to REF – convert to all zeros (00000000). For proper operation, REF + must be at least 1 V higher than REF –. Also, the total unadjusted error may increase as this differential reference voltage falls below 4.75 V. 5. Linearity error is the maximum deviation from the best straight line through the A/D transfer characteristics. 6. Zero-scale error is the difference between 00000000 and the converted output for zero input voltage; full-scale error is the difference between 11111111 and the converted output for full-scale input voltage. 7. Total unadjusted error is the sum of linearity, zero-scale, and full-scale errors. 8. Both the input address and the output codes are expressed in positive logic. The A11 analog input signal is internally generated and is used for test purposes. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 PARAMETER MEASUREMENT INFORMATION 1.4 V VCC 3 kΩ 3 kΩ Test Point Output Under Test Test Point Output Under Test CL (see Note A) CL (see Note A) LOAD CIRCUIT FOR td, tr, AND tf Output Under Test Test Point CL (see Note A) 3 kΩ LOAD CIRCUIT FOR tPZH AND tPHZ LOAD CIRCUIT FOR tPZL AND tPLZ NOTE A: CL = 50 pF Figure 1. Load Circuits Address Valid 2V CS 0.8 V 2V 0.8 V An tPZH, tPZL tPHZ, tPLZ 2.4 V 90% 0.4 V 10% DATA OUT tsu(A) 2V I/O CLOCK Figure 3. Address Timing Figure 2. CS to Data Output Timing 2V CS 0.8 V tsu(CS) I/O CLOCK th(CS) 2V 8th Clock 0.8 V Figure 4. Figure 4. CS to I/O CLOCK Timing 6 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 th(A) TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 PARAMETER MEASUREMENT INFORMATION tr(I/O) tf(I/O) 2V 2V I/O CLOCK 0.8 V 0.8 V 0.8 V f(clock I/O) td(I/O-DATA) t(v) DATA OUT 2.4 V 2.4 V 0.4 V 0.4 V tr(bus), tf(bus) Figure 5. Data Output Timing I/O CLOCK 8th Clock 0.8 V td(I/O-EOC) 2.4 V EOC 0.4 V tf(EOC) Figure 6. EOC Timing tr(EOC) EOC 2.4 V 0.4 V td(EOC-DATA) 2.4 V DATA OUT 0.4 V Valid MSB Figure 7. Data Output to EOC Timing POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7 TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 APPLICATION INFORMATION simplified analog input analysis Using the equivalent circuit in Figure 8, the time required to charge the analog input capacitance from 0 to VS within 1/2 LSB can be derived as follows: The capacitance charging voltage is given by ( VC = VS 1– e – tc/RtCi ) (1) where Rt = Rs + ri The final voltage to 1/2 LSB is given by VC (1/2 LSB) = VS – (VS /512) (2) Equating equation 1 to equation 2 and solving for time tc gives ( VS – (VS/512) = VS 1– e – tc/RtCi ) (3) and tc (1/2 LSB) = Rt × Ci × ln(512) (4) Therefore, with the values given the time for the analog input signal to settle is tc (1/2 LSB) = (Rs + 1 kΩ) × 60 pF × ln(512) (5) This time must be less than the converter sample time shown in the timing diagrams. Driving Source† TLC542 Rs VS VI ri VC 1 kΩ MAX Ci 50 pF MAX VI = Input Voltage at INPUT A0 – A10 VS = External Driving Source Voltage Rs = Source Resistance ri = Input Resistance Ci = Input Capacitance † Driving source requirements: • Noise and distortion for the source must be equivalent to the resolution of the converter. • Rs must be real at the input frequency. Figure 8. Equivalent Input Circuit Including the Driving Source 8 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 TLC542C, TLC542I 8-BIT ANALOG-TO-DIGITAL CONVERTERS WITH SERIAL CONTROL AND 11 INPUTS SLAS075C – FEBRUARY 1989 – REVISED JUNE 2001 PRINCIPLES OF OPERATION The TLC542 is a complete data acquisition system on a single chip. The device includes such functions as analog multiplexer, sample and hold, 8-bit A/D converter, data and control registers, and control logic. Three control inputs (I/O CLOCK, CS (chip select), and ADDRESS INPUT) are included for flexibility and access speed. These control inputs and a TTL-compatible 3-state output are intended for serial communications with a microprocessor or microcomputer. With judicious interface timing, the TLC542 can complete a conversion in 20 µs, while complete input-conversion-output cycles can be repeated every 40 µs. Furthermore, this fast conversion can be executed on any of 11 inputs or its built-in self-test and in any order desired by the controlling processor. When CS is high, the DATA OUT terminal is in a 3-state condition, and the ADDRESS INPUT and I/O CLOCK terminals are disabled. When additional TLC542 devices are used, this feature allows each of these terminals, with the exception of the CS terminal, to share a control logic point with their counterpart terminals on additional A/D devices. Thus, this feature minimizes the control logic terminals required when using multiple A/D devices. The control sequence is designed to minimize the time and effort required to initiate conversion and obtain the conversion result. A normal control sequence is as follows: 1. CS is brought low. To minimize errors caused by noise at the CS input, the internal circuitry waits for two rising edges and then a falling edge of the internal system clock before recognizing the low CS transition. The MSB of the result of the previous conversion automatically appears on the DATA OUT terminal. 2. On the first four rising edges of the I/O CLOCK, a new positive-logic multiplexer address is shifted in, with the MSB of this address shifted first. The negative edges of these four I/O CLOCK pulses shift out the second, third, fourth, and fifth most significant bits of the result of the previous conversion. The on-chip sample and hold begins sampling the newly addressed analog input after the fourth falling edge of the I/O CLOCK. The sampling operation basically involves charging the internal capacitors to the level of the analog input voltage. 3. Three clock cycles are applied to the I/O CLOCK terminal and the sixth, seventh, and eighth conversion bits are shifted out on the negative edges of these clock cycles. 4. The final eighth clock cycle is applied to the I/O CLOCK terminal. The falling edge of this clock cycle initiates a 12-system clock (≈ 12 µs) additional sampling period while the output is in the high-impedance state. Conversion is then performed during the next 20 µs. After this final I/O CLOCK cycle, CS must go high or the I/O CLOCK must remain low for at least 20 µs to allow for the conversion function. CS can be kept low during periods of multiple conversion. If CS is taken high, it must remain high until the end of conversion. Otherwise, a valid falling edge of CS causes a reset condition, which aborts the conversion process. A new conversion may be started and the ongoing conversion simultaneously aborted by performing steps 1 through 4 before the 20-µs conversion time has elapsed. Such action yields the conversion result of the previous conversion and not the ongoing conversion. The end-of-conversion (EOC) output goes low on the negative edge of the eighth I/O CLOCK. The subsequent low-to-high transition of EOC indicates the A/D conversion is complete and the conversion is ready for transfer. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 9 PACKAGE OPTION ADDENDUM www.ti.com 25-May-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TLC542CDW ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC542CDWG4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC542CDWR ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC542CDWRG4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC542CN ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC542CNE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC542IDW ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC542IDWG4 ACTIVE SOIC DW 20 25 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC542IDWR ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC542IDWRG4 ACTIVE SOIC DW 20 2000 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM TLC542IFN ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM TLC542IFNG3 ACTIVE PLCC FN 20 46 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM TLC542IFNR ACTIVE PLCC FN 20 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM TLC542IFNRG3 ACTIVE PLCC FN 20 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM TLC542IN ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type TLC542INE4 ACTIVE PDIP N 20 20 Pb-Free (RoHS) CU NIPDAU N / A for Pkg Type Lead/Ball Finish MSL Peak Temp (3) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 PACKAGE OPTION ADDENDUM www.ti.com 25-May-2009 (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DLP® Products DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee® Solutions amplifier.ti.com dataconverter.ti.com www.dlp.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2009, Texas Instruments Incorporated