TPD2E007 www.ti.com SLVS796E – SEPTEMBER 2008 – REVISED AUGUST 2010 2-CHANNEL ESD-PROTECTION ARRAY FOR AC-COUPLED/NEGATIVE-RAIL DATA INTERFACES Check for Samples: TPD2E007 FEATURES 1 • 2 • • • • • YFMG4 PACKAGE (BOTTOM VIEW) ESD Protection Exceeds IEC61000-4-2 (Level 4) – ±15-kV Human-Body Model (HBM) – ±8-kV IEC 61000-4-2 Contact Discharge – ±15-kV IEC 61000-4-2 Air-Gap Discharge 4.5-A Peak Pulse Current (8/20 ms Pulse) 15-pF Line to GND Capacitance Low 50-nA Leakage Current 2-Channel Device Space-Saving PicoStar™ and DCK Package B1 B2 GND IO1 A1 A2 IO2 0.8 mm × 0.8 mm (0.4 mm pitch) YFMG4 PIN DESCRIPTIONS TERMINAL NAME IO APPLICATIONS • • • • GND GND Cell Phones, PDAs Audio Interface Connections Consumer Electronics (DVR, Set-Top Box, TV) Industrial Interface (RS-232, RS-485, RS-422, LVDS) NO. DESCRIPTION A1, A2 ESD-protection channel B1, B2 Ground DCK PACKAGE (TOP VIEW) IO1 1 3 IO2 GND 2 DESCRIPTION/ORDERING INFORMATION This device is an application-specific integrated parts (ASIP) designed to offer system level ESD solutions for wide range of portable and industrial applications. The back-to-back diode array allows AC-coupled or negative-going data transmission (audio interface, LVDS, RS-485, RS-232, etc.) without compromising signal integrity. The PicoStar™ package is intended to be embedded inside the printed circuit board which saves board space in portable applications. This device exceeds the IEC61000-4-2 (Level 4) ESD protection and suitable to provide system level ESD protection for the valuable internal ICs while placed near the connector. The TPD2E007 is offered in a 4-bump PicoStar™ and 3-pin DCK packages. The PicoStar™ package (YFMG4), with only 0.15 mm (Max) package height, is recommended for ultra space saving application where the package height is a key concern. The PicoStar™ package can be used in either embedded PCB board applications or in surface mount applications. The industry standard DCK package offers straightforward board layout option in legacy designs. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PicoStar is a trademark of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2008–2010, Texas Instruments Incorporated TPD2E007 SLVS796E – SEPTEMBER 2008 – REVISED AUGUST 2010 www.ti.com ORDERING INFORMATION PACKAGE (1) TA (2) ORDERABLE PART NUMBER TOP-SIDE MARKING –40°C to 85°C DSLGA – YFM Tape and reel TPD2E007YFMRG4 45 T –40°C to 85°C 3-DCK Tape and reel TPD2E007DCKR 45U (1) (2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging. For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. EQUIVALENT SCHEMATIC REPRESENTATION IO1 IO2 GND ABSOLUTE MAXIMUM RATINGS (1) over operating free-air temperature range (unless otherwise noted) VIO Continuous power dissipation (TA = 70°C) MIN MAX UNIT –13.5 13.5 V YFM package 270 DCK package 218 mW Operating temperature range –40 85 °C Tstg Storage temperature range –65 150 °C TJ Junction temperature 150 °C Bump temperature (soldering) Infrared (15 s) 220 Vapor phase (60 s) 215 Lead temperature (soldering, 10 s) (1) °C 300 °C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum-rated conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS TA = –40°C to 85°C (unless otherwise noted) PARAMETER VBR Break-down voltage IIO Channel leakage current Rd Dynamic resistance CIN Channel input capacitance (1) TEST CONDITIONS IIO = 10 mA MIN TYP (1) MAX 20 50 nA 15 pF ±14 V Ω 3.5 VIO = 2.5 V UNIT 10 Typical values are at VCC = 5 V and TA = 25°C. ESD Protection PARAMETER HBM TYP UNIT ±15 kV IEC 61000-4-2 Contact Discharge ±8 kV IEC 61000-4-2 Air-Gap Discharge ±15 kV 2 Submit Documentation Feedback Copyright © 2008–2010, Texas Instruments Incorporated Product Folder Link(s): TPD2E007 TPD2E007 www.ti.com SLVS796E – SEPTEMBER 2008 – REVISED AUGUST 2010 TYPICAL OPERATING CHARACTERISTICS IEC Clamping Waveforms (20 ns/div) 40 280 20 0 240 –20 –40 200 Amplitude (V) Amplitude (V) –60 160 120 80 –80 –100 –120 –140 –160 –180 –200 40 –220 –240 0 –260 –280 –40 0 20 40 60 80 100 120 140 160 180 200 0 20 40 60 Time (ns) Figure 1. 8-kV Contact 80 100 120 Time (ns) 140 160 180 200 Figure 2. –8-kV Contact 1.5E-11 1.50E-01 1.4E-11 1.25E-01 1.3E-11 1.00E-01 1.2E-11 7.50E-02 1.1E-11 2.50E-02 9.0E-12 Amps Capacitance (F) 5.00E-02 1.0E-11 8.0E-12 0.00E+00 –2.50E-02 7.0E-12 Device 2 6.0E-12 –5.00E-02 Device 1 5.0E-12 –7.50E-02 4.0E-12 –1.00E-01 Device 1 3.0E-12 –1.25E-01 Device 2 2.0E-12 2.5 3.0 3.5 4.0 4.5 5.0 7. 5 10 .0 12 .5 15 .0 17 .5 20 .0 2.0 2. 5 1.5 5. 0 1.0 0. 0 0.5 –2 0.0 0. 0 –1 7. 5 –1 5. 0 –1 2. 5 –1 0. 0 –7 .5 –5 .0 -2 .5 –1.50E-01 1.0E-12 Volts Input Voltage (V) Figure 3. Capacitance vs Input Voltage at TA = 27°C Figure 4. Diode Breakdown Voltage Data at TA = 27°C Submit Documentation Feedback Copyright © 2008–2010, Texas Instruments Incorporated Product Folder Link(s): TPD2E007 3 TPD2E007 SLVS796E – SEPTEMBER 2008 – REVISED AUGUST 2010 www.ti.com REVISION HISTORY Changes from Revision D (October 2009) to Revision E • 4 Page Added max continuous power dissipation value for DCK package ...................................................................................... 2 Submit Documentation Feedback Copyright © 2008–2010, Texas Instruments Incorporated Product Folder Link(s): TPD2E007 PACKAGE OPTION ADDENDUM www.ti.com 18-Aug-2010 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty 3000 Green (RoHS & no Sb/Br) TBD Call TI Call TI Samples Not Available 3000 Green (RoHS & no Sb/Br) Call TI Level-1-260C-UNLIM Request Free Samples TPD2E007DCKR ACTIVE SC70 DCK 3 TPD2E007YFMR PREVIEW DSLGA YFM 4 TPD2E007YFMRG4 ACTIVE DSLGA YFM 4 Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) CU NIPDAU Level-2-260C-1 YEAR Request Free Samples (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Dec-2010 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant TPD2E007DCKR SC70 DCK 3 3000 179.0 8.4 2.4 2.4 1.19 4.0 8.0 Q3 TPD2E007YFMRG4 DSLGA YFM 4 3000 178.0 9.2 0.84 0.84 0.28 4.0 8.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 11-Dec-2010 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) TPD2E007DCKR SC70 DCK 3 3000 195.0 200.0 45.0 TPD2E007YFMRG4 DSLGA YFM 4 3000 220.0 220.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps RF/IF and ZigBee® Solutions www.ti.com/lprf TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated