EXAR XR-2207CP

XR-2207
...the analog plus
Voltage-Controlled
Oscillator
company TM
June 1997–3
FEATURES
APPLICATIONS
Excellent Temperature Stability (20ppm/°C)
FSK Generation
Linear Frequency Sweep
Voltage and Current-to-Frequency Conversion
Adjustable Duty Cycle (0.1% to 99.9%)
Stable Phase-Locked Loop
Two or Four Level FSK Capability
Waveform Generation
Wide Sweep Range (1000:1 Minimum)
– Triangle, Sawtooth, Pulse, Squarewave
Logic Compatible Input and Output Levels
FM and Sweep Generation
Wide Supply Voltage Range (4V to 13V)
Low Supply Sensitivity (0.1% /V)
Wide Frequency Range (0.01Hz to 1MHz)
Simultaneous Triangle and Squarewave Outputs
GENERAL DESCRIPTION
The XR-2207 is a monolithic voltage-controlled oscillator
(VCO) integrated circuit featuring excellent frequency
stability and a wide tuning range. The circuit provides
simultaneous triangle and squarewave outputs over a
frequency range of 0.01Hz to 1MHz. It is ideally suited for
FM, FSK, and sweep or tone generation, as well as for
phase-locked loop applications.
The XR-2207 has a typical drift specification of 20ppm/°C.
The oscillator frequency can be linearly swept over a
1000:1 range with an external control voltage; and the
duty cycle of both the triangle and the squarewave
outputs can be varied from 0.1% to 99.9% to generate
stable pulse and sawtooth waveforms.
ORDERING INFORMATION
Part No.
Package
Operating
Temperature Range
XR-2207M
14 Lead 300 Mil CDIP
-55°C to +125°C
XR-2207CP
14 Lead 300 Mil PDIP
0°C to +70°C
XR-2207D
16 Lead 300 Mil JEDEC SOIC
0°C to +70°C
XR-2207ID
16 Lead 300 Mil JEDEC SOIC
-40°C to +85°C
BLOCK DIAGRAM
Timing
Capacitor
Timing
Resistors
C1
C1
R1
R2
R3
R4
2
3
4
5
6
Î
Î
Î
VCC GND
1
BIAS
10
11
A1
VCO
14
TWO
Triangle Wave Out
13
SWO
Square Wave Out
12
VEE
9
BKI2
BKI1
A2
Current
Switches
8
Binary
Keying
Inputs
7
Figure 1. Block Diagram
Rev. 2.02
1975
EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 (510) 668-7000 FAX (510) 668-7017
1
XR-2207
PIN CONFIGURATION
VCC
C1
C2
R1
R2
R3
R4
1
14
2
13
3
12
4
11
5
10
6
9
7
8
VCC
C1
C2
R1
R2
R3
R4
BKI1
TWO
SWO
VEE
BIAS
GND
BKI2
BKI1
14 Lead PDIP, CDIP (0.300”)
Pin #
Symbol
Description
1
VCC
2
C1
I
Timing Capacitor Input.
3
C2
I
Timing Capacitor Input.
4
R1
I
Timing Resistor 1 Input.
5
R2
I
Timing Resistor 2 Input.
6
R3
I
Timing Resistor 3 Input.
7
R4
I
Timing Resistor 4 Input.
8
BKI1
I
Binary Keying 1 Timing Resistor Select Input.
9
BKI2
I
Binary Keying 2 Timing Resistor Select Input.
Positive Power Supply.
10
GND
11
BIAS
Ground Pin.
12
VEE
13
SWO
O
Square Wave Output Signal.
14
TWO
O
Triangle Wave Output Signal.
15, 16
NC
I
16
2
15
3
14
4
13
5
12
6
11
7
10
8
9
NC
NC
TWO
SWO
VEE
BIAS
GND
BKI2
16 Lead SOIC (Jedec, 0.300”)
PIN DESCRIPTION
Type
1
Bias Input for Single Supply Operation.
Negative Power Supply.
Only SOIC-16 Package.
Rev. 2.02
2
XR-2207
ELECTRICAL CHARACTERISTICS
Test Conditions: Test Circuit of Figure 3 and Figure 4, VCC = VEE = 6V, TA = +25°C, C = 5000pF, R1 = R2 =
R3 = R4 = 20kΩ, RL = 4.7kΩ, Binary Inputs Grounded, S1 and S2 Closed Unless Otherwise Specified
XR-2207ID/XR-2207M
Parameters
Min.
Typ.
XR-2207CP/D
Max.
Min.
Typ.
Max.
Units
Conditions
General Characteristics
Supply Voltage
Single Supply
8
26
8
26
V
See Figure 3
S
Split
li Supplies
S
li
4
13
4
13
V
See Figure 4
See Figure 3
Supply Current
Single Supply
5
7
5
8
mA
Measure at Pin 1, S1, S2
Open
See Figure 4
Split Supply
Positive
5
7
5
8
mA
Measure at Pin 1, S1, S2
Open
Negative
4
6
4
7
mA
Measured at Pin 12, S1, S2
Open
1.0
MHz
C =500pF, R3 = 2kΩ
0.01
Hz
C =50µF, R3 = 2MΩ
Oscillator Section - Frequency Characteristics
Upper Frequency Limit
0.5
1.0
Lowest Practical Frequency
0.01
Frequency Accuracy
1
Frequency Matching
0.5
0.5
3
1
5
% of fO
0.5
% of fO
30
ppm/°C
0.15
%V
1000:1
fH/fL
Frequency Stability
Temperature
20
P
Power S
Supply
l
0.15
Sweep Range
50
1000:1 3000:1
Sweep Linearity
%
10:1 Sweep
1
1000:1 Sweep
S
5
5
0.1
0.1
FM Distortion
Recommended Range of
Timing Resistors
1.5
2
2000
1.5
1.5
0°C < TA< 70°C
R3 = 1.5kΩ for fH1
R3 = 2MΩ for fL
C =5000pF
fH=10kHz, fL= 1kHz
fH=100kHz, fL= 100Hz
2000
%
10% FM Deviation
kΩ
See Characteristic Curves
Impedance at Timing Pins
75
75
Ω
Measured at Pins 4, 5, 6, or 7
DC Level at Timing Terminals
10
10
mV
Binary Keying Inputs
Switching Threshold
Input Impedance
1.4
2.2
2.8
1.4
5
2.2
5
2.8
V
Measured at Pins 8 and 9,
Referenced to Pin 10
kΩ
Notes
Bold face parameters are covered by production test and guaranteed over operating temperature range.
Rev. 2.02
3
XR-2207
ELECTRICAL CHARACTERISTICS (CONT’D)
XR-2207ID/XR-2207M
Parameters
Min.
Typ.
Max.
XR-2207CP/D
Min.
Typ.
Max.
Units
Conditions
Output Characteristics
Triangle Output
Amplitude
Measured at Pin 13
4
Impedance
I
d
DC Level
L
l
Linearity
6
4
6
VPP
10
10
Ω
+100
+100
mV
0.1
0.1
%
Squarewave Output
Amplitude
Referenced to Pin 10
From 10% to 90% to Swing
Measured at Pin 13, S2
Closed
11
12
11
0.4
12
0.2
Vpp
Saturation Voltage
0.2
0.4
V
Referenced to Pin 12
Rise Time
200
200
nsec
CL 10pF
Fall Time
20
20
nsec
CL 10pF
Notes
Bold face parameters are covered by production test and guaranteed over operating temperature range.
Specifications are subject to change without notice
ABSOLUTE MAXIMUM RATINGS
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26V
Storage Temperature Range . . . . . -65°C to +150°C
Power Dissipation (package limitation)
Ceramic package . . . . . . . . . . . . . . . . . . . . . . . 750mW
Derate above +25°C . . . . . . . . . . . . . . . . . . 6mW/°C
Plastic package . . . . . . . . . . . . . . . . . . . . . . . . .
Derate above +25°C . . . . . . . . . . . . . . . . . .
SOIC package . . . . . . . . . . . . . . . . . . . . . . . . .
Derate above +25°C . . . . . . . . . . . . . . . . .
Rev. 2.02
4
625mW
5mW/°C
500mW
4mW/°C
XR-2207
Q1 Q2
1
Q3 Q4
Q14
Q15
VCC
2R
Q13
R
R
Q5
R
Q19
R3
3
Q8
Q10
Q9
R2
Q11
R4
4R
7
Timing Resistors
6
5
4
Q16
Square Wave
Output
Q18
R5
R6
R7
13
9
Q17
Binary
Keying
Inputs
B
B
A
A
Triangle Wave
Output
2R
Q12
Timing
Capacitor
2
Q7
14
R
R1
Q6
–
+
Q20
Q21
Q27
8
10
Q22
Ground
11
BIAS
Q24
Q25 Q26
Q23
VEE
12
Figure 2. Equivalent Schematic Diagram
Rev. 2.02
5
XR-2207
PRECAUTIONS
SYSTEM DESCRIPTION
The following precautions should be observed when
operating the XR-2207 family of integrated circuits:
The XR-2207 functional blocks are shown in the block
diagram given in Figure 1. They are a voltage controlled
oscillator (VCO), four current switches which are
controlled by binary keying inputs, and two buffer
amplifiers for triangle and squarewave outputs. Figure 2
is a simplified XR-2207 schematic diagram that shows the
circuit in greater detail.
The VCO is a modified emitter-coupled current controlled
multivibrator. Its oscillation is inversely proportional to the
value of the timing capacitor connected to pins 2 and 3,
and directly proportional to the total timing current IT. This
current is determined by the resistors that are connected
from the four timing terminals (pins 4, 5, 6 and 7) to
ground, and by the logic levels that are applied to the two
binary keying input terminals (pins 8 and 9). Four different
oscillation frequencies are possible since IT can have four
different values.
The triangle output buffer has a low impedance output
(10Ω TYP) while the squarewave is an open-collector
type. An external bias input allows the XR-2207 to be
used in either single or split supply applications.
1. Pulling excessive current from the timing terminals
will adversely affect the temperature stability of the
circuit. To minimize this disturbance, it is
recommended that the total current drawn from pins
4, 5, 6, and 7 be limited to 6mA. In addition,
permanent damage to the device may occur if the
total timing current exceeds 10mA.
2. Terminals 2, 3, 4, 5, 6 , and 7 have very low internal
impedance and should, therefore, be protected from
accidental shorting to ground or the supply voltage.
3. The keying logic pulse amplitude should not exceed
the supply voltage.
VCC
VCC
S2
I+
C
0.1µF
RL
1
2
V+ C1
Binary
Keying Inputs
0.1µF
8
9
10
3
C2
SWO
A
XR-2207
B
TWO
Square Wave
Output
13
14
Triangle Wave
Output
11
BIAS
GND
5.1K
R1 R 2 R 3 R4 V4
5
6
7
12
R1 R2 R3 R4
3.9K
S1
Figure 3. Test Circuit for Single Supply Operation
Rev. 2.02
6
VCC
XR-2207
VCC
VCC
S2
I+
C
0.1µF
1
8
Binary
Keying Inputs
9
10
V+
2
C1
3
C2
SWO
A
XR-2207
B
TWO
BIAS
GND
R1 R2 R3 R4 V4
5
6 7 12
13
14
RL
Square Wave
Output
Triangle Wave
Output
11
IVEE
R1 R2 R3 R4
0.1µF
S1
Figure 4. Test Circuit for Split Supply Operation
OPERATING CONSIDERATIONS
Bypass Capacitors
The recommended value for bypass capacitors is 1µF
although larger values are required for very low frequency
operation.
Supply Voltage (Pins 1 and 12)
The XR-2207 is designed to operate over a power supply
range of 4V to 13V for split supplies, or 8V to 26V for
single supplies. Figure 5 shows the permissible supply
voltage for operation with unequal split supply voltages.
Figure 6 and Figure 7 show supply current versus supply
voltage Performance is optimum for 6V split supply, or
12V single supply operation. At higher supply voltages,
the frequency sweep range is reduced.
Timing Resistors (Pins 4, 5, 6, and 7)
The timing resistors determine the total timing current, IT,
available to charge the timing capacitor. Values for timing
resistors can range from 2kΩ to 2MΩ; however, for
optimum temperature and power supply stability,
recommended values are 4kΩ to 200kΩ (see Figure 8,
Figure 9, Figure 10 and Figure 11). To avoid parasitic pick
up, timing resistor leads should be kept as short as
possible. For noisy environments, unused or deactivated
timing terminals should be bypassed to ground through
0.1µF capacitors.
Ground (Pin 10)
For split supply operation, this pin serves as circuit
ground. For single supply operation, pin 10 should be AC
grounded through a 1µF bypass capacitor. During split
supply operation, a ground current of 2IT flows out of this
terminal, where IT is the total timing current.
Timing Capacitor (Pins 2 and 3)
The oscillator frequency is inversely proportional to the
timing capacitor, C. The minimum capacitance value is
limited by stray capacitances and the maximum value by
physical size and leakage current considerations.
Recommended values range from 100pF to 100µF. The
capacitor should be non-polarized.
Bias for Single Supply (Pin 11)
For single supply operation, pin 11 should be externally
biased to a potential between V+/3 and V+/2V (see
Figure 3). The bias current at pin 11 is nominally 5% of the
total oscillation timing current, IT.
Rev. 2.02
7
XR-2207
25
35
30
15
Positive Supply (mA)
Positive Supply
20
Typical
Operating
Range
10
5
25
RT=Parallel Combination
of Activated Timing
Resistors
TA=25°C
20
RT=2kΩ
RT=200kΩ
10
RT=20kΩ
5
0
4
0
-5
-10
-15
RT=5kΩ
RT=3kΩ
15
6
8
RT=2MkΩ
10
12
14
-20
Negative Supply (V)
8 10 12 14 16 18 20 22 24 26 28
Single Supply Voltage (V)
Figure 6. Positive Supply Current, 1+ (Measured
at Pin 1) vs. Supply Voltage
Figure 5. Operating Range for Unequal Split
Supply Voltages
TA=25°C
TA=25°C
Total Timing Resistor RT
Negative Supply Current (mA)
15
10
5
0
0
6
8
10
12
1MΩ
100kΩ
Timing
Resistor
Range
10kΩ
1kΩ
0
4V
8V
12V
0
8
16
24
Single Supply Voltage (V)
14
Split Supply Voltage (V)
Figure 7. Negative Supply Current, I(Measured at Pin 12) vs. Supply Voltage
Figure 8. Recommended Timing Resistor
Value vs. Power Supply Voltage
Rev. 2.02
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
1.04
1K
10K
100K
Normalized Frequency Drift
VS=6V
C=5000pF
1M
RT=2MΩ
1.02
RT=200kΩ
.98
.96
TA=25°C
RT=Total
Timing
Resistance
C=5000pF
.94
.92
2
10M
4
4
Figure 9. Frequency Accuracy vs.
Timing Resistance
8
VS=6V
C=5000pF
+1%
6
8
10
12
Split Supply Voltage (V)
12
16
20
24
Single Supply Voltage (V)
2MΩ
200kΩ
2kΩ
0
20kΩ
20kΩ
4kΩ
-1%
200kΩ
-2%
R=2kΩ
2MΩ
-3%
-50
RT=2kΩ
14
28
Figure 10. Frequency Drift vs. Supply Voltage
+2%
4kΩ
RT=20kΩ
1.00
Timing Resistance (Ω)
Normalized Frequency Drift (%)
Frequency Error (%)
XR-2207
-25
0
+25 +50 +75 +100 +125
Temperature (°C)
Figure 11. Normalized Frequency Drift with
Temperature
Rev. 2.02
9
XR-2207
Binary Keying Inputs (Pins 8 and 9)
Timing Capacitor
VCC
C
The logic levels applied to the two binary keying inputs
allow the selection of four different oscillator frequencies.
The internal impedance at these pins is approximately
5kΩ. Keying voltages, which are referenced to pin 10, are
< 1.4 V for “zero” and > 3V for “one” logic levels. Table 1
relates binary keying input logic levels, and selected
timing pins to oscillator output frequency for each of the
four possible cases.
1
3
IT/2
2
IT/2
Ib
T4
T3
T2
T1
Figure 12 shows the oscillator control mechanism in
greater detail. Timing pins 4, 5, 6 and 7 correspond to the
emitters of switching transistor pairs T1, T2, T3, and T4
respectively, which are internal to the integrated circuit.
The current switches, and corresponding timing
terminals, are activated by external logic signals applied
to pins 8 and 9.
A
8
B
Binary
Keying
Controls
4
9
I1
10
5
6
7
I2
I3
I4
V
R1 R2 R3 R4
12
VEE
Logic Level
Selected
Timing Pins
Frequency
Pin 8
Pin 9
0
0
6
f1
0
1
6 and 7
f1 + f1
1
0
5
f2
1
1
4 and 5
f2 + f2
Figure 12. Simplified Schematic of Frequency
Control Mechanism
Squarewave Output (Pin 13)
The squarewave output at pin 13 is an “open-collector”
stage capable of sinking up to 20mA of load current. RL
serves as a pull-up load resistor for this output.
Recommended values for RL range from 1kΩ to 100kΩ.
Table 1. Logic Table for Binary Keying Controls
Triangle Output (Pin 14)
The output at pin 14 is a triangle wave with a peak swing of
approximately one-half of the total supply voltage. Pin 14
has a 10Ω output impedance and is internally protected
against short circuits.
Definitions:
f1 + 1 f1 + 1 f2 + 1 f2 + 1
R3C
R4C
R2C
R1C
MODES OF OPERATION
Split Supply Operation
Figure 13 is the recommended configuration for split
supply operation. The circuit operates with supply
voltages ranging from $4V to $13V. Minimum drift
occurs with $6V supplies. For operation with unequal
supply voltages, see Figure 5.
Logic Levels: 0 = Ground, 1 3V
Note
For single supply operation, logic levels
are referenced to
voltage at pin 10
With the generalized circuit of Figure 13A, the frequency
of operation is determined by the timing capacitor, C, and
the activated timing resistors (R1 through R4). The timing
resistors are activated by the logic signals at the binary
Rev. 2.02
10
XR-2207
peak-to-peak voltage swing equal to the supply voltages.
This output is an “open-collector” type and requires an
external pull-up load resistor (nominally 5kΩ) to the
positive supply. The triangle waveform obtained at pin 14
is centered about ground and has a peak amplitude of
V+/2.
keying inputs (pins 8 and 9), as shown in the logic table
(Table 1). If a single timing resistor is activated, the
frequency is 1/RC. Otherwise, the frequency is either
1/(R1||R2)C or 1/(R3||R4)C.
Figure 13B shows a fixed frequency application using a
single timing resistor that is selected by grounding the
binary keying inputs. The oscillator frequency is 1/R3C.
Note
For Single-Supply Operation, Logic Levels are referenced to
voltage at Pin 10.
The squarewave output is obtained at pin 13 and has a
VCC
C
VCC
CB
RL
1
8
Keying Inputs
9
2
3
V+ C1
C2
SWO
A
Square Wave
Output
13
14
Triangle Wave
Output
TWO
XR-2207
B
BIAS 11
10 GND
R 1 R 2 R 3 R 4 V4 5 6
7 12
R1 R2 R3 R4
VEE
CB
CB = Bypass Cap
VEE
A. General Case
C
VCC
CB
VCC
RL
1
8
9
10
2
3
V+ C 1
C2
Square Wave
Output
SWO
A
B
13
XR-2207
TWO
14
11
BIAS
GND
f=1/R3<C
R 1 R 2 R 3 R4 V4 5 6
7 12
R3
VEE
CB
CB = Bypass Cap
VEE
B. Fixed Frequency Case
Figure 13. Split-Supply Operation
Rev. 2.02
11
Triangle Wave
Output
XR-2207
For single supply operation, the DC voltage at pin 10 and
the timing terminals (pins 4 through 7) are equal and
approximately 0.6V above VB, the bias voltage at pin 11.
The logic levels at the binary keying terminals are
referenced to the voltage at pin 10.
Single Supply Operation
The circuit should be interconnected as shown in
Figure 14A or Figure 14B for single supply operation. Pin
12 should be grounded, and pin 11 biased from VCC
through a resistive divider to a value of bias voltage
between V+/3 and V+/2. Pin 10 is bypassed to ground
through a 1µF capacitor.
VCC
C
VCC
CB
RL
1
8
Keying Inputs
9
CB
10
V+
2
C1
3
C2
Square Wave
Output
13
SWO
A
XR-2207
B
TWO
BIAS
GND
14
Triangle Wave
Output
11
VCC
5.1K
R 1 R 2 R 3 R 4 V4
5
6
7
12
CB = Bypass Cap
R1 R2 R3
3.9K
R4
A. General Case
CB
VCC
C
VCC
RL
1
V+
8
9
10
2
C1
3
C2
SWO
A
B
XR-2207
BIAS
GND
CB
TWO
Square Wave
Output
13
14
Triangle Wave
Output
11
5.1K
R 1 R 2 R 3 R 4 V4
5
6
7
12
VCC
3.9K
R3
f=1/R3<C
CB = Bypass Cap
B. Single Frequency
Figure 14. Single Supply Operation
Rev. 2.02
12
XR-2207
The circuit of Figure 15 can operate both with positive and
negative values of control voltage. However, for positive
values of VC with small (RC/R3) ratio, the direction of the
timing current IT is reversed and the oscillations will stop.
Frequency Control (Sweep and FM)
The frequency of operation is controlled by varying the
total timing current, IT, drawn from the activated timing
pins 4, 5, 6, or 7. The timing current can be modulated by
applying a control voltage, VC, to the activated timing pin
through a series resistor RC. As the control voltage
becomes more negative, both the total timing current, IT,
and the oscillation frequency increase.
Figure 16 shows an alternate circuit for frequency control
where two timing pins, 6 and 7, are activated. The
frequency and the conversion gain expressions are the
same as before, except that the circuit will operate only
with negative values of VC. For VC > 0, pin 7 becomes
deactivated and the frequency is fixed at:
The circuits given in Figure 15 and Figure 16 show two
different frequency sweep methods for split supply
operation.
f+ 1
R3
Both binary keying inputs are grounded for the circuit in
Figure 15. Therefore, only timing pin 6 is activated.
The circuit given in Figure 17 shows the frequency sweep
method for single supply operation. Here, the oscillation
frequency is given as:
f+ 1
The frequency of operation, normally
R3C is now
proportional to the control voltage, VC, and determined
as:
f+ 1
R3C
f+ 1
R3C
ƪ1 * VR RV-ƫ Hz
C
ƪ1 ) RR ǒ1 * VV Ǔƫ
3
C
C
T
3
C
where VT = Vbias + 0.7V.
If R3 = 2MΩ, RC = 2kΩ, C = 5000pF, then a 1000:1
frequency sweep would result for a negative sweep
voltage VC V-.
This equation is valid from VC = 0V (RC is in parallel with
R3) to
ǒ
VC + VT 1 ) RC
R3
The voltage to frequency conversion gain, K, is controlled
by the series resistance RC and can be expressed as:
K + f + 1
HzńV
VC
RCCV-
Ǔ
Caution
Total timing current IT must be less than 6mA over the frequency
control range.
Rev. 2.02
13
XR-2207
VCC
CB
VCC
C
4.7K
8
ƪ
f + 1 1 * VCR3
RCVCR3
9
ƫ
1 2
V+ C1
A
SWO
TWO
XR-2207
B
10
3
C2
BIAS
Square Wave
Output
13
14
Triangle Wave
Output
11
GND
R1 R2 R3 R4 V4 5 6 7 12
IT
IO
VEE
IC
CB
CB = Bypass Cap
R3 RC
VEE VC
VC
Sweep or FM input
Figure 15. Frequency Sweep Operation, Split Supply
VCC
CB
VCC
C
4.7K
1
8
ƪ
f + 1 1 * VCR3
RCVCR3
ƫ
VCC
9
10
V+
2
C1
3
C2
A
B
XR-2207
SWO
TWO
13
Square Wave
Output
14
Triangle Wave
Output
BIAS 11
GND
R1 R2 R3 R4 V4
5 6 7
12
VEE
IO
CB = Bypass Cap
IC
CB
R3 RC
VEE VC
VC
Sweep or FM input
Figure 16. Alternate Frequency Sweep Operation, Split Supply
Rev. 2.02
14
XR-2207
VCC
VCC
1µF
C
Square Wave
Output
4.7K
1
2
V+ C1
ƪ
ǒ
f + 1 1 ) R3 1 * VC
RC
VT
CR3
3
13
C2
SWO
14
TWO
XR-2207
11
BIAS
8 A
Ǔƫ
9
B
10 GND
Triangle Wave
Output
Vbias
VCC
5.1K
R1 R2 R3 R4 V4 5 6 7 12
1µF
1µF
3.9K
VEE
VT
R3
RC
VC-
1µF
VC+
VC
Sweep or FM input
Figure 17. Frequency Sweep Operation, Single Supply
Duty Cycle Control
Duty Cycle +
The duty cycle of the output waveforms can be controlled
by frequency shift keying at the end of every half cycle of
oscillator output. This is accomplished by connecting one
or both of the binary keying inputs (pins 8 or 9) to the
squarewave output at pin 13. The output waveforms can
then be converted to positive or negative pulses and
sawtooth waveforms.
R2
R2 ) R3
and can be varied from 0.1% to 99.9% by proper choice of
timing resistors. The frequency of oscillation, f, is given
as:
ƪ
1
f+2
C R2 ) R3
Figure 18 is the recommended circuit connection for duty
cycle control. Pin 8 is shorted to pin 13 so that the circuit
switches between the “0,0” and the “1,0” logic states
given in Table 1. Timing pin 5 is activated when the output
is “high,” and the timing pin is activated when the
squarewave output goes to a low state.
ƫ
The frequency can be modulated or swept without
changing the duty cycle by connecting R2 and R3 to a
common control voltage VC, instead of VEE (see
Figure 15).
The sawtooth and the pulse output
waveforms are shown in Figure 19.
The duty cycle of the output waveforms is given as:
Rev. 2.02
15
XR-2207
4.7K
VCC
VCC
C
CB
1
8
9
10
V+
2
3
C1
C2
SWO
A
TWO
XR-2207
B
BIAS
GND
R1
R2
4
R2
R3
5
6
R4
7
13
Pulse
Output
14
Sawtooth
Output
11
V12
R3
VEE
CB
CB = Bypass Cap
VEE
Figure 18. Duty Cycle Control
Rev. 2.02
16
XR-2207
On-Off Keying
The XR-2207 can be keyed on and off by simply activating
an open circuited timing pin. Under certain conditions, the
circuit may exhibit very low frequency (<1Hz) residual
oscillations in the “off” state due to internal bias currents. If
this effect is undesirable, it can be eliminated by
connecting a 10MΩ resistor from pin 3 to VCC.
A. Squarewave and Triangle Outputs
Two-Channel FSK Generator (Modem Transmitter)
The multi-level frequency shift-keying capability of
XR-2207 makes it ideally suited for two-channel FSK
generation. A recommended circuit connection for this
application is shown in Figure 20.
For two-channel FSK generation, the “mark” and “space”
frequencies of the respective channels are determined by
the timing resistor pairs (R1, R2) and (R3, R4). Pin 8 is the
“channel-select” control in accord with Figure 11. For a
“high” logic level at pin 8, the timing resistors R1 and R2
are activated. Similarly, for a “low” logic level, timing
resistors R3 and R4 are enabled.
B. Pulse and Sawtooth Outputs
The “high” and “low” logic levels at pin 9 determine the
respective high and low frequencies within the selected
FSK channel. When only a single FSK channel is used,
the remaining channel can be deactivated by connecting
pin 8 to either VCC or ground. In this case, the unused
timing resistors can also be omitted from the circuit.
The low and high frequencies, f1 and f2, for a given FSK
channel can be fine tuned using potentiometers
connected in series with respective timing resistors. In
fine tuning the frequencies, f1 should be set first with the
logic level at pin 9 in a “low” level.
C. Frequency Shift Keyed Outputs
Typical frequency drift of the circuit for 0°C to 75°C
operation is $0.2%. Since the frequency stability is
directly related to the external timing components, care
must be taken to use timing components with low
temperature coefficients.
Figure 19. Output Waveforms
Rev. 2.02
17
XR-2207
VCC
VCC
C
1µF
RL
1
2
V+ C1
Channel
Select
3V
OV
f2
f1
8
9
Keying
Input
10
3
C2
SWO
A
TWO
XR-2207
B
BIAS
13
FSK
Output
14
11
f1
GND
R1
R1
R2
R3 R4
4
5
6
R2
R3
R4
V7
12
1µF
10K
10K
10K
10K
VEE
Figure 20. Multi-Channel FSK Generation
Rev. 2.02
18
f2
XR-2207
14 LEAD CERAMIC DUAL-IN-LINE
(300 MIL CDIP)
Rev. 1.00
14
8
1
7
E
E1
D
A1
Base
Plane
Seating
Plane
A
L
e
c
B
α
B1
INCHES
SYMBOL
MILLIMETERS
MIN
MAX
MIN
MAX
A
0.100
0.200
2.54
5.08
A1
0.015
0.060
0.38
1.52
B
0.014
0.026
0.36
0.66
B1
0.045
0.065
1.14
1.65
c
0.008
0.018
0.20
0.46
D
0.685
0.785
17.40
19.94
E1
0.250
0.310
6.35
7.87
E
0.300 BSC
7.62 BSC
e
0.100 BSC
2.54 BSC
L
0.125
0.200
3.18
5.08
α
0°
15°
0°
Note: The control dimension is the inch column
15°
Rev. 2.02
19
XR-2207
14 LEAD PLASTIC DUAL-IN-LINE
(300 MIL PDIP)
Rev. 1.00
14
8
1
7
E1
E
D
Seating
Plane
A2
A
L
α
A1
B
INCHES
SYMBOL
eA
eB
B1
e
MILLIMETERS
MIN
MAX
MIN
MAX
A
0.145
0.210
3.68
5.33
A1
0.015
0.070
0.38
1.78
A2
0.115
0.195
2.92
4.95
B
0.014
0.024
0.36
0.56
B1
0.030
0.070
0.76
1.78
C
0.008
0.014
0.20
0.38
D
0.725
0.795
18.42
20.19
E
0.300
0.325
7.62
8.26
E1
0.240
0.280
6.10
7.11
e
0.100 BSC
2.54 BSC
eA
0.300 BSC
7.62 BSC
eB
0.310
0.430
7.87
10.92
L
0.115
0.160
2.92
4.06
α
0°
15°
0°
15°
Note: The control dimension is the inch column
Rev. 2.02
20
C
XR-2207
16 LEAD SMALL OUTLINE
(300 MIL JEDEC SOIC)
Rev. 1.00
D
16
9
E
H
1
8
C
A
Seating
Plane
e
B
α
A1
L
INCHES
SYMBOL
MILLIMETERS
MIN
MAX
MIN
A
0.093
0.104
2.35
2.65
A1
0.004
0.012
0.10
0.30
B
0.013
0.020
0.33
0.51
C
0.009
0.013
0.23
0.32
D
0.398
0.413
10.10
10.50
E
0.291
0.299
7.40
7.60
e
0.050 BSC
MAX
1.27 BSC
H
0.394
0.419
10.00
10.65
L
0.016
0.050
0.40
1.27
α
0°
8°
0°
8°
Note: The control dimension is the millimeter column
Rev. 2.02
21
XR-2207
Notes
Rev. 2.02
22
XR-2207
Notes
Rev. 2.02
23
XR-2207
NOTICE
EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are
free of patent infringement. Charts and schedules contained herein are only for illustration purposes and may vary
depending upon a user’s specific application. While the information in this publication has been carefully checked;
no responsibility, however, is assumed for inaccuracies.
EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or
malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly
affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation
receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the
user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances.
Copyright 1975 EXAR Corporation
Datasheet June 1997
Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited.
Rev. 2.02
24