PHILIPS 74F74

INTEGRATED CIRCUITS
74F74
Dual D-type flip-flop
Product specification
Supercedes data of 1990 Oct 23
IC15 Data Handbook
1996 Mar 12
Philips Semiconductors
Product specification
Dual D-type flip-flop
74F74
FEATURE
PIN CONFIGURATION
• Industrial temperature range available (–40°C to +85°C)
DESCRIPTION
The 74F74 is a dual positive edge-triggered D-type flip-flop featuring
individual data, clock, set, and reset inputs; also true and
complementary outputs. Set (SD) and reset (RD) are asynchronous
active low inputs and operate independently of the clock input. When
set and reset are inactive (high), data at the D input is transferred to
the Q and Q outputs on the low-to-high transition of the clock. Data
must be stable just one setup time prior to the low-to-high transition of
the clock for predictable operation. Clock triggering occurs at a
voltage level and is not directly related to the transition time of the
positive-going pulse. Following the hold time interval, data at the D
input may be changed without affecting the levels of the output.
TYPE
74F74
RD0
1
14
VCC
D0
2
13
RD1
CP0
3
12
D1
SD0
4
11
CP1
Q0
5
10
SD1
Q0
6
9
Q1
GND
7
8
Q1
SF00045
TYPICAL fmax
TYPICAL SUPPLY CURRENT (TOTAL)
125MHz
11.5mA
ORDERING INFORMATION
ORDER CODE
DESCRIPTION
COMMERCIAL RANGE
VCC = 5V ±10%,
Tamb = 0°C to +70°C
INDUSTRIAL RANGE
VCC = 5V ±10%,
Tamb = –40°C to +85°C
PKG. DWG. #
14-pin plastic DIP
N74F74N
I74F74N
SOT27-1
14-pin plastic SO
N74F74D
I74F74D
SOT108-1
INPUT AND OUTPUT LOADING AND FAN OUT TABLE
PINS
DESCRIPTION
D0, D1
74F (U.L.) HIGH/LOW
LOAD VALUE HIGH/LOW
Data inputs
1.0/1.0
20µA/0.6mA
CP0, CP1
Clock inputs (active rising edge)
1.0/1.0
20µA/0.6mA
SD0, SD1
Set inputs (active low)
1.0/3.0
20µA/1.8mA
RD0, RD1
Reset inputs (active low)
1.0/3.0
20µA/1.8mA
Q0, Q1, Q0, Q1
Data outputs
50/33
NOTE: One (1.0) FAST unit load is defined as: 20µA in the high state and 0.6mA in the low state.
LOGIC SYMBOL
IEC/IEEE SYMBOL
2
12
4
D0 D1
3
CP0
4
SD0
5
C1
2
1
1
RD0
11
CP1
10
SD1
13
RD1
10
5
1D
6
R
S
9
11
C2
12
13
6
9
2D
8
R
8
SF00047
SF00046
1996 Mar 12
&
S
3
Q0 Q0 Q1 Q1
VCC = Pin 14
GND = Pin 7
1.0mA/20mA
2
853 0335 16554
Philips Semiconductors
Product specification
Dual D-type flip-flop
74F74
LOGIC DIAGRAM
FUNCTION TABLE
INPUTS
SD
RD
CP
D
4, 10
5, 9
1, 13
Q
6, 8
3, 11
Q
OUTPUTS
OPERATING
MODE
SD
RD
CP
D
Q
Q
L
H
X
X
H
L
Asynchronous set
H
L
X
X
L
H
Asynchronous reset
L
L
X
X
H
H
Undetermined*
H
H
↑
h
H
L
Load ”1”
H
H
↑
l
L
H
Load ”0”
H
H
↑
X
NC
NC
Hold
NOTES:
H = High voltage level
h = High voltage level one setup time prior to low-to-high clock
transition
L = Low voltage level
l = Low voltage level one setup time prior to low-to-high clock
transition
NC= No change from the previous setup
X = Don’t care
↑ = Low-to-high clock transition
↑ = Not low-to-high clock transition
* = This setup is unstable and will change when either set or reset
return to the high level.
2, 12
VCC = Pin 14
GND = Pin 7
SF00048
ABSOLUTE MAXIMUM RATINGS
(Operation beyond the limit set forth in this table may impair the useful life of the device.
Unless otherwise noted these limits are over the operating free air temperature range.)
PARAMETER
SYMBOL
RATING
UNIT
VCC
Supply voltage
–0.5 to +7.0
V
VIN
Input voltage
–0.5 to +7.0
V
IIN
Input current
–30 to +5
mA
VOUT
Voltage applied to output in high output state
–0.5 to VCC
V
IOUT
Current applied to output in low output state
40
mA
Commercial range
0 to +70
Tamb
Operating free air temperature range
°C
Industrial range
–40 to +85
°C
Tstg
Storage temperature range
–65 to +150
°C
RECOMMENDED OPERATING CONDITIONS
LIMITS
SYMBOL
PARAMETER
MIN
NOM
MAX
5.0
5.5
UNIT
VCC
Supply voltage
4.5
VIH
High-level input voltage
2.0
VIL
Low-level input voltage
0.8
V
IIk
Input clamp current
–18
mA
IOH
High-level output current
–1
mA
IOL
Low-level output current
Tambb
1996 Mar 12
Operating
O
erating free air tem
temperature
erature range
V
V
20
mA
Commercial range
0
+70
°C
Industrial range
–40
+85
°C
3
Philips Semiconductors
Product specification
Dual D-type flip-flop
74F74
DC ELECTRICAL CHARACTERISTICS
(Over recommended operating free-air temperature range unless otherwise noted.)
SYMBOL
VOH
O
High level output voltage
High-level
VCC = MIN
MIN, VIL = MAX,
MAX VIH = MIN
VOL
O
Low level output voltage
Low-level
VCC = MIN
MIN, VIL = MAX,
MAX VIH = MIN
VIK
Input clamp voltage
VCC = MIN, II = IIK
II
Input current at maximum input
voltage
VCC = MAX, VI = 7.0V
IIH
High-level input current
IOH
O = MAX
IOL
O = MAX
±10%VCC
2.5
±5%VCC
2.7
±10%VCC
±5%VCC
TYP2
MAX
UNIT
V
3.4
V
0.30
0.50
V
0.30
0.50
V
-0.73
-1.2
V
100
µA
VCC = MAX, VI = 2.7V
20
µA
VCC = MAX, VI = 0.5V
-0.6
mA
SDn, RDn
VCC = MAX, VI = 0.5V
Low-level input
current
IOS
Short-circuit output current3
Supply current (total)
MIN
Dn, CPn
IIL
ICC
LIMITS
TEST CONDITIONS1
PARAMETER
4
VCC = MAX
-60
VCC = MAX
11.5
-1.8
mA
-150
mA
16
mA
NOTES:
1 For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type.
2 All typical values are at VCC = 5V, Tamb = 25°C.
3 Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold
techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting
of a high output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any
sequence of parameter tests, IOS tests should be performed last.
4 Measure ICC with the clock input grounded and all outputs open, then with Q and Q outputs high in turn.
AC ELECTRICAL CHARACTERISTICS
LIMITS
VCC = +5.0V
Tamb = +25°C
CL = 50pF, RL = 500Ω
VCC = +5.0V ± 10%
Tamb = 0°C to +70°C
CL = 50pF, RL = 500Ω
VCC = +5.0V ± 10%
Tamb = –40°C to +85°C
CL = 50pF, RL = 500Ω
PARAMETER
TEST
CONDITION
MIN
TYP
fmax
Maximum clock frequency
Waveform 1
100
125
tPLH
tPHL
Propagation delay
CPn to Qn or Qn
Waveform 1
3.8
4.4
5.3
6.2
6.8
8.0
3.8
4.4
7.8
9.2
3.8
4.4
8.5
9.2
ns
tPLH
tPHL
Propagation delay
SDn, RDn to Qn or Qn
Waveform 2
3.2
3.5
4.6
7.0
6.1
9.0
3.2
3.5
7.1
10.5
3.2
2.5
7.5
10.5
ns
SYMBOL
MAX
MIN
MAX
100
MIN
UNIT
MAX
90
MHz
AC SETUP REQUIREMENTS
LIMITS
SYMBOL
PARAMETER
TEST
CONDITION
VCC = +5.0V
Tamb = +25°C
CL = 50pF, RL = 500Ω
MIN
TYP
MAX
VCC = +5.0V ± 10%
Tamb = 0°C to +70°C
CL = 50pF, RL = 500Ω
MIN
MAX
VCC = +5.0V ± 10%
Tamb = –40°C to +85°C
CL = 50pF, RL = 500Ω
MIN
UNIT
MAX
tsu (H)
tsu (L)
Setup time, high or low
Dn to CPn
Waveform 1
2.0
3.0
2.0
3.0
2.0
3.0
ns
th (H)
th (L)
Hold time, high or low
Dn to CPn
Waveform 1
1.0
1.0
1.0
1.0
1.0
1.0
ns
tw (H)
tw (L)
CPn pulse width,
high or low
Waveform 1
4.0
5.0
4.0
5.0
4.0
5.0
ns
tw (L)
SDn, RDn pulse width,
low
Waveform 2
4.0
4.0
4.0
ns
trec
Recovery time
SDn, RDn to CPn
Waveform 3
2.0
2.0
2.0
ns
1996 Mar 12
4
Philips Semiconductors
Product specification
Dual D-type flip-flop
74F74
AC WAVEFORMS
For all waveforms, VM = 1.5V.
The shaded areas indicate when the input is permitted to
change for predictable output performance.
Dn
VM
tsu(L)
VM
VM
tsu(H)
th(L)
VM
tw(L)
SDn VM
VM
th(H)
1/fmax
CPn
VM
VM
tw(L)
RDn
tw(L)
VM
VM
tw(H)
VM
tPHL
tPLH
tPHL
tPLH
Qn
Qn
VM
VM
VM
VM
tPLH
tPHL
tPLH
tPHL
VM
VM
Qn
VM
VM
Qn
SF00050
Waveform 2. Propagation delay for set and reset to output,
set and reset pulse width
SF01276
Waveform 1. Propagation delay for data to output, data setup
time and hold times, and clock width, and maximum clock
frequency
SDn or RDn
VM
trec
CPn
VM
SF00051
Waveform 3. Recovery time for set or reset to clock
TEST CIRCUIT AND WAVEFORMS
VCC
VIN
tw
90%
NEGATIVE
PULSE
VM
D.U.T.
RT
CL
RL
AMP (V)
VM
10%
VOUT
PULSE
GENERATOR
90%
10%
tTHL (tf )
tTLH (tr )
tTLH (tr )
tTHL (tf )
0V
AMP (V)
90%
90%
POSITIVE
PULSE
DEFINITIONS:
RL = Load resistor;
see AC ELECTRICAL CHARACTERISTICS for value.
CL = Load capacitance includes jig and probe capacitance;
see AC ELECTRICAL CHARACTERISTICS for value.
RT = Termination resistance should be equal to ZOUT of
pulse generators.
VM
VM
10%
Test Circuit for Totem-Pole Outputs
10%
tw
0V
Input Pulse Definition
INPUT PULSE REQUIREMENTS
family
amplitude VM
74F
3.0V
1.5V
rep. rate
tw
tTLH
tTHL
1MHz
500ns
2.5ns
2.5ns
SF00006
1996 Mar 12
5
Philips Semiconductors
Product specification
Dual D-type flip-flop
74F74
DIP14: plastic dual in-line package; 14 leads (300 mil)
1996 Mar 12
6
SOT27-1
Philips Semiconductors
Product specification
Dual D-type flip-flop
74F74
SO14: plastic small outline package; 14 leads; body width 3.9 mm
1996 Mar 12
7
SOT108-1
Philips Semiconductors
Product specification
Dual D-type flip-flop
74F74
Data sheet status
Data sheet
status
Product
status
Definition [1]
Objective
specification
Development
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
Preliminary
specification
Qualification
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
Product
specification
Production
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
[1] Please consult the most recently issued datasheet before initiating or completing a design.
Definitions
Short-form specification — The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition — Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information — Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support — These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
 Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 94088–3409
Telephone 800-234-7381
print code
Document order number:
yyyy mmm dd
8
Date of release: 10-98
9397-750-05066