Features • Programmable 33,554,432 x 1-bit Serial Memories Designed to Store Configuration Programs for Field Programmable Gate Arrays (FPGAs) • 3.3V Output Capability • 5V Tolerant I/O Pins • Program Support using the Atmel ATDH2200E System or Industry Third Party Programmers In-System Programmable (ISP) via 2-wire Bus Simple Interface to SRAM FPGAs Compatible with Altera® FLEX®, Excalibur™, Stratix™, Cyclone™ and APEX™ Devices Cascadable Read-back to Support Additional Configurations or Higher-density Arrays Low-power CMOS FLASH Process Available in 44 PLCC Packages Emulation of Atmel’s AT24Cxxx Serial EEPROMs Low-power Standby Mode Single Device Capable of Holding 4 Individual Bit Stream Files Allowing Simple System Reconfiguration • Endurance: 10,000 Write Cycles Typical • Green (Lead and Halide-Free/ROHS Compliant) Package Options Available • • • • • • • • • FPGA Configuration Flash Memory AT17F32A 1. Description The AT17FxxA Series of In-System Programmable Configuration PROMs (Configurators) provide an easy-to-use, cost-effective configuration memory for Field Programmable Gate Arrays. The AT17FxxA Series device is packaged in the 44-lead PLCC see Table 1-1. The AT17FxxA Series Configurator uses a simple serial-access procedure to configure one or more FPGA devices. The AT17FxxA Series Configurators can be programmed with industry-standard programmers, Atmel’s ATDH2200E Programming Kit or Atmel’s ATDH2225 ISP Cable. Table 1-1. Package 44-lead PLCC AT17FxxA Series Packages AT17F32A Yes 3489C–CNFG–08/07 2. Pin Configuration 39 38 37 36 35 34 33 32 31 30 29 18 19 20 21 22 23 24 25 26 27 28 7 8 9 10 11 12 13 14 15 16 17 NC SER_EN NC NC READY NC PAGESEL1 NC NC NC NC NC GND PAGESEL0 NC NC NC NC NC NC NC nCASC/A2 NC DCLK NC NC NC NC NC NC NC RESET/OE nCS 6 5 4 3 2 1 44 43 42 41 40 NC NC NC NC DATA PAGE_EN NC NC NC VCC NC 44-lead PLCC 2 AT17F32A 3489C–CNFG–08/07 AT17F32A 3. Block Diagram READY PAGE_EN PAGESEL0 PAGESEL1 Power-on Reset Reset Clock/Oscillator Logic nCASC(A2) Config. Page Select Serial Download Logic 2-wire Serial Programming Flash Memory DCLK CE/WE/OE Data Address DATA nCS Control Logic RESET/OE SER_EN 4. Device Description The control signals for the configuration memory device (nCS, RESET/OE and DCLK) interface directly with the FPGA device control signals. All FPGA devices can control the entire configuration process and retrieve data from the configuration device without requiring an external intelligent controller. The RESET/OE and nCS pins control the tri-state buffer on the DATA output pin and enable the address counter. When RESET/OE is driven Low, the configuration device resets its address counter and tri-states its DATA pin. The nCS pin also controls the output of the AT17FxxA Series Configurator. If nCS is held High after the RESET/OE reset pulse, the counter is disabled and the DATA output pin is tri-stated. When OE is subsequently driven High, the counter and the DATA output pin are enabled. When RESET/OE is driven Low again, the address counter is reset and the DATA output pin is tri-stated, regardless of the state of nCS. When the configurator has driven out all of its data and nCASC is driven Low, the device tristates the DATA pin to avoid contention with other configurators. Upon power-up, the address counter is automatically reset. 3 3489C–CNFG–08/07 5. Pin Description AT17F32A Name I/O 44 PLCC DATA I/O 2 DCLK I/O 8 PAGE_EN I 1 PAGESEL0 I 20 PAGESEL1 I 33 RESET/OE I 16 nCS I 17 GND – 19 nCASC O A2 I READY O 35 SER_EN I 38 VCC – 41 28 5.1 DATA(1) Three-state DATA output for FPGA configuration. Open-collector bi-directional pin for configuration programming. 5.2 DCLK(1) Three-state clock. Functions as an input when the Configurator is in programming mode (i.e. SER_EN is Low) and as an output during FPGA configuration. 5.3 PAGE_EN(2) Input used to enable page download mode. When PAGE_EN is high the configuration download address space is partitioned into 4 equal pages. This gives users the ability to easily store and retrieve multiple configuration bitstreams from a single configuration device. This input works in conjunction with the PAGESEL inputs. PAGE_EN must be remain low if paging is not desired. When SER_EN is Low (ISP mode) this pin has no effect. Notes: 1. This pin has an internal 20 KΩ pull-up resistor. 2. This pin has an internal 30 KΩ pull-down resistor. 4 AT17F32A 3489C–CNFG–08/07 AT17F32A 5.4 PAGESEL[1:0](2) Page select inputs. Used to determine which of the 4 memory pages are targeted during a serial configuration download. The address space for each of the pages is shown in Table 5-1. When SER_EN is Low (ISP mode) these pins have no effect. Table 5-1. 5.5 Address Space Paging Decodes AT17F32A (32 Mbits) PAGESEL = 00, PAGE_EN = 1 000000 – 07FFFFh PAGESEL = 01, PAGE_EN = 1 080000 – 0FFFFFh PAGESEL = 10, PAGE_EN = 1 100000 – 17FFFFh PAGESEL = 11, PAGE_EN = 1 180000 – 1FFFFFh PAGESEL = XX, PAGE_EN = 0 000000 – 1FFFFFh RESET/OE(1) Output Enable (active High) and RESET (active Low) when SER_EN is High. A Low level on RESET/OE resets both the address and bit counters. A High level (with nCS Low) enables the data output driver. 5.6 nCS(1) Chip Enable input (active Low). A Low level (with OE High) allows DCLK to increment the address counter and enables the data output driver. A High level on nCS disables both the address and bit counters and forces the device into a low-power standby mode. Note that this pin will not enable/disable the device in the 2-wire Serial Programming mode (SER_EN Low). 5.7 GND Ground pin. A 0.2 µF decoupling capacitor between VCC and GND is recommended. 5.8 nCASC Cascade Select Output (when SER_EN is High). This output goes Low when the internal address counter has reached its maximum value. If the PAGE_EN input is set High, the maximum value is the highest address in the selected partition. The PAGESEL[1:0] inputs are used to make the 4 partition selections. If the PAGE_EN input is set Low, the device is not partitioned and the address maximum value is the highest address in the device, see Table 5-1 on page 5. In a daisy chain of AT17FxxA Series devices, the nCASC pin of one device must be connected to the nCS input of the next device in the chain. It will stay Low as long as nCS is Low and OE is High. It will then follow nCS until OE goes Low; thereafter, nCASC will stay High until the entire EEPROM is read again. Notes: 1. This pin has an internal 20 KΩ pull-up resistor. 2. This pin has an internal 30 KΩ pull-down resistor. 5 3489C–CNFG–08/07 5.9 A2(1) Device selection input, (when SER_EN Low). The input is used to enable (or chip select) the device during programming (i.e., when SER_EN is Low). Refer to the AT17FxxA Programming Specification available on the Atmel web site for additional details. 5.10 READY Open collector reset state indicator. Driven Low during power-up reset, released when power-up is complete. (recommended 4.7 kΩ pull-up on this pin if used). 5.11 SER_EN(1) The serial enable input must remain High during FPGA configuration operations. Bringing SER_EN Low enables the 2-Wire Serial Programming Mode. For non-ISP applications, SER_EN should be tied to VCC. 5.12 VCC +3.3V (±10%). Notes: 1. This pin has an internal 20 KΩ pull-up resistor. 2. This pin has an internal 30 KΩ pull-down resistor. 6 AT17F32A 3489C–CNFG–08/07 AT17F32A 6. FPGA Master Serial Mode Summary The I/O and logic functions of any SRAM-based FPGA are established by a configuration program. The program is loaded either automatically upon power-up, or on command, depending on the state of the FPGA mode pins. In Master mode, the FPGA automatically loads the configuration program from an external memory. The AT17FxxA Serial Configuration PROM has been designed for compatibility with the Master Serial mode. This document discusses the Atmel AT40K, AT40KAL and AT94KAL applications as well as Altera applications. 7. Control of Configuration Most connections between the FPGA device and the AT17FxxA Serial Configurator PROM are simple and self-explanatory. • The DATA output of the AT17FxxA Series Configurator drives DIN of the FPGA devices. • The DCLK output of the AT17FxxA device drives the DCLK input data of the FPGA. • The nCASC output of a AT17FxxA Series Configurator drives the nCS input of the next Configurator in a cascade chain of configurator devices. • SER_EN must be at logic High level (internal pull-up resistor provided) except during ISP. • The READY pin is available as an open-collector indicator of the device’s reset status; it is driven Low while the device is in its power-on reset cycle and released (tri-stated) when the cycle is complete. • PAGE_EN must remain Low if download paging is not desired. If paging is desired, PAGE_EN must be High and the PAGESEL pins must be set to High or Low such that the desired page is selected, see Table 5-1 on page 5. 8. Cascading Serial Configuration Devices For multiple FPGAs configured as a daisy-chain, or for FPGAs requiring larger configuration memories, cascaded configurators provide additional memory. After the last bit from the first configurator is read, the clock signal to the configurator asserts its nCASC output Low and disables its DATA line driver. The second configurator recognizes the Low level on its nCS input and enables its DATA output. After configuration is complete, the address counters of all cascaded configurators are reset if the RESET/OE on each configurator is driven to its active (Low) level. If the address counters are not to be reset upon completion, then the RESET/OE input can be tied to its inactive (High) level. 9. Programming Mode The programming mode is entered by bringing SER_EN Low. In this mode the chip can be programmed by the 2-wire serial bus. The programming is done at VCC supply only. Programming super voltages are generated inside the chip. The AT17FxxA parts are read/write at 3.3V nominal. Refer to the AT17FxxA Programming Specification available on the Atmel web site (www.atmel.com) for more programming details. AT17FxxA devices are supported by the Atmel ATDH2200 programming system along with many third party programmers. 7 3489C–CNFG–08/07 10. Standby Mode The AT17FxxA Series Configurators enter a low-power standby mode whenever SER_EN is High and nCS is asserted High. In this mode, the AT17FxxA Configurator typically consumes less than 1 mA of current at 3.3V. The output remains in a high-impedance state regardless of the state of the OE input. 11. Absolute Maximum Ratings* Operating Temperature.................................... -40°C to +85 °C *NOTICE: Storage Temperature ..................................... -65°C to +150°C Voltage on Any Pin with Respect to Ground ..............................-0.5V to VCC +0.5V Supply Voltage (VCC) .........................................-0.5V to +4.0V Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those listed under operating conditions is not implied. Exposure to Absolute Maximum Rating conditions for extended periods of time may affect device reliability. Maximum Soldering Temp. (10 sec. @ 1/16 in.).............260°C ESD (RZAP = 1.5K, CZAP = 100 pF)................................. 2000V 12. Operating Conditions AT17FxxA Series Configurator Symbol Description Min Max Units Commercial Supply voltage relative to GND -0°C to +70°C 2.97 3.63 V Industrial Supply voltage relative to GND -40°C to +85°C 2.97 3.63 V VCC 13. DC Characteristics AT17F32A Symbol Description Min Max Units VIH High-level Input Voltage 2.0 VCC V VIL Low-level Input Voltage 0 0.8 V VOH High-level Output Voltage (IOH = -2.5 mA) VOL Low-level Output Voltage (IOL = +3 mA) VOH High-level Output Voltage (IOH = -2 mA) VOL Low-level Output Voltage (IOL = +3 mA) 0.4 V ICCA Supply Current, Active Mode at Freq. Max. 50 mA IL Input or Output Leakage Current (VIN = VCC or GND) 10 µA Commercial 3 mA ICCS Supply Current, Standby Mode Industrial 3 mA 8 2.4 V Commercial 0.4 2.4 V V Industrial -10 AT17F32A 3489C–CNFG–08/07 AT17F32A 14. AC Characteristics nCS TSCE TSCE THCE RESET/OE TLC THOE THC CLK TOE TOH TCAC TDF TCE DATA TOH 15. AC Characteristics when Cascading RESET/OE nCS CLK TCDF DATA FIRST BIT LAST BIT TOCK TOCE TOOE nCASC TOCE 9 3489C–CNFG–08/07 16. AC Characteristics AT17F32A Symbol Description TOE(2) OE to Data Delay TCE(2) nCS to Data Delay TCAC(2) DCLK to Data Delay TOH Data Hold from nCS, OE, or DCLK TDF(3) nCS or OE to Data Float Delay TLC DCLK Low Time THC DCLK High Time TSCE Min Typ Max Units 50 ns Industrial 55 ns Commercial 55 ns Industrial 60 ns Commercial 30 ns 30 ns Commercial (1) (1) (1) Industrial Commercial 0 ns Industrial(1) 0 ns Commercial (1) Industrial 15 ns 15 ns Commercial 15 ns Industrial(1) 15 ns Commercial 15 ns Industrial 15 ns nCS Setup Time to DCLK (to guarantee proper counting) Commercial 20 ns Industrial 25 ns nCS Hold Time from DCLK (to guarantee proper counting) Commercial 0 ns THCE Industrial 0 ns RESET/OE Low Time (guarantees counter is reset) Commercial 20 ns THOE 20 ns Maximum Input Clock Frequency SEREN = 0 Commercial FMAX TWR Write Cycle Time(4) TEC Erase Cycle Time(4) Notes: (1) (1) (1) (1) Industrial (1) Industrial 10 MHz 10 MHz Commercial 12 µs Industrial(1) 12 µs Commercial 50 s 50 s (1) Industrial 1. Preliminary specifications for military operating range only. 2. AC test lead = 50 pF. 3. Float delays are measured with 5 pF AC loads. Transition is measured ±200 mV from steady-state active levels. 4. See the AT17F Programming Specfication for procedural information. 5. The times given are per byte (typical). 10 AT17F32A 3489C–CNFG–08/07 AT17F32A AC Characteristics When Cascading AT17F32A Symbol Description TCDF(3) DCLK to Data Float Delay TOCK(2) DCLK to nCASC Delay TOCE(2) nCS to nCASC Delay TOOE(2) RESET/OE to nCASC Delay Notes: Min Max Units Commercial 50 ns Industrial 50 ns Commercial 50 ns Industrial 55 ns Commercial 35 ns Industrial 40 ns Commercial 35 ns Industrial 35 ns 1. AC test lead = 50 pF. 2. Float delays are measured with 5 pF AC loads. Transition is measured ± 200 mV from steady-state active levels. 17. Thermal Resistance Coefficients Package Type 44J Note: Plastic Leaded Chip Carrier (PLCC) AT17F32A θJC [°C/W] θJA [°C/W] (1) – – 1. Airflow = 0 ft/min. 11 3489C–CNFG–08/07 18. Ordering Information Memory Size Ordering Code Package Operation Range AT17F32A-30BJI 44J-44PLCC Industrial (-40°C to 85°C) AT17F32A-30BJU 44J-44PLCC LHF Industrial (-40°C to 85°C) 32-Mbit Note: 1. The last time buy date is December 29, 2006 for the shaded parts. Package Type 44J 12 44-lead, Plastic J-leaded Chip Carrier (PLCC) AT17F32A 3489C–CNFG–08/07 AT17F32A 19. Packaging Information 19.1 44J – PLCC 1.14(0.045) X 45˚ PIN NO. 1 1.14(0.045) X 45˚ 0.318(0.0125) 0.191(0.0075) IDENTIFIER E1 D2/E2 B1 E B e A2 D1 A1 D A 0.51(0.020)MAX 45˚ MAX (3X) COMMON DIMENSIONS (Unit of Measure = mm) Notes: 1. This package conforms to JEDEC reference MS-018, Variation AC. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is .010"(0.254 mm) per side. Dimension D1 and E1 include mold mismatch and are measured at the extreme material condition at the upper or lower parting line. 3. Lead coplanarity is 0.004" (0.102 mm) maximum. SYMBOL MIN NOM MAX A 4.191 – 4.572 A1 2.286 – 3.048 A2 0.508 – – D 17.399 – 17.653 D1 16.510 – 16.662 E 17.399 – 17.653 E1 16.510 – 16.662 D2/E2 14.986 – 16.002 B 0.660 – 0.813 B1 0.330 – 0.533 e NOTE Note 2 Note 2 1.270 TYP 10/04/01 R 2325 Orchard Parkway San Jose, CA 95131 TITLE 44J, 44-lead, Plastic J-leaded Chip Carrier (PLCC) DRAWING NO. REV. 44J B 13 3489C–CNFG–08/07 Headquarters International Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600 Atmel Asia Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369 Atmel Europe Le Krebs 8, Rue Jean-Pierre Timbaud BP 309 78054 Saint-Quentin-enYvelines Cedex France Tel: (33) 1-30-60-70-00 Fax: (33) 1-30-60-71-11 Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581 Technical Support [email protected] Sales Contact www.atmel.com/contacts Product Contact Web Site www.atmel.com Literature Requests www.atmel.com/literature Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDITIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2007 Atmel Corporation. All rights reserved. Atmel®, logo and combinations thereof, Everywhere You Are ®, and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. 3489C–CNFG–08/07