SEMICONDUCTOR TECHNICAL DATA " !# # The MC10H350 is a member of Motorola’s 10H family of high performance ECL logic. It consists of 4 translators with differential inputs and TTL outputs. The 3–state outputs can be disabled by applying a HIGH TTL logic level on the common OE input. The MC10H350 is designed to be used primarily in systems incorporating both ECL and TTL logic operating off a common power supply. The separate VCC power pins are not connected internally and thus isolate the noisy TTL VCC runs from the relatively quiet ECL VCC runs on the printed circuit board. The differential inputs allow the H350 to be used as an inverting or noninverting translator, or a differential line receiver. The H350 can also drive CMOS with the addition of a pullup resistor. • Propagation Delay, 3.5 ns Typical • MECL 10K–Compatible L SUFFIX CERAMIC PACKAGE CASE 620–10 P SUFFIX PLASTIC PACKAGE CASE 648–08 FN SUFFIX PLCC CASE 775–02 MAXIMUM RATINGS Characteristic Power Supply (VEE = Gnd) Symbol Rating Unit VCC 7.0 Vdc TA 0 to +75 °C Tstg –55 to +150 –55 to +165 °C °C Operating Temperature Range Storage Temperature Range — Plastic — Ceramic LOGIC DIAGRAM 9 ELECTRICAL CHARACTERISTICS (VCC = 5.0 V ±5%) (See Note 1) TA = 0°C to 75°C Characteristic 3 4 2 5 6 7 11 12 10 13 14 15 Symbol Min Max Unit TTL ECL ICC — — 20 12 mA Input Current High Pin 9 Others IIH IINH — — 20 50 µA Input Current Low Pin 9 Others IIL IINL — — –0.6 50 mA µA Input Voltage High Pin 9 VIH 2.0 — Vdc Input Voltage Low Pin 9 VIL — 0.8 Vdc VDIFF 350 — mV VCM 2.8 VCC Vdc Output Voltage High IOH = 3.0 mA VOH 2.7 — Vdc Output Voltage Low IOL = 20 mA VOL — 0.5 Vdc ECL VCC 1 16 TTL VCC Short Circuit Current VOUT = 0 V IOS –60 –150 mA AOUT 2 15 COUT 3 14 CIN IOZH — 50 µA AIN Output Disable Current High VOUT = 2.7 V AIN 4 13 CIN Output Disable Current Low VOUT = 0.5 V IOZL — –50 µA BIN 5 12 DIN BIN 6 11 DIN BOUT 7 10 DOUT GND 8 9 OE Power Supply Current Differential Input Voltage (1) Pins 3–6, 11–14 (1) Voltage Common Mode VCC (+5.0 VDC) = PINS 1 AND 16 GND = PIN 8 DIP PIN ASSIGNMENT Pins 3–6, 11–14 (1) Common mode input voltage to pins 3–4, 5–6, 11–12, 13–14 must be between the values of 2.8 V and 5.0 V. This common mode input voltage range includes the differential input swing. (2) For single ended use, apply 3.75 V (VBB) to either input depending on output polarity required. Signal level range to other input is 3.3 V to 4.2 V. (3) Any unused gates should have the inverting inputs tied to VCC and the non–inverting inputs tied to ground to prevent output glitching. (4) 1.0 V to 2.0 V w/50 pF into 500 ohms. *Positive Emitter Coupled Logic Pin assignment is for Dual–in–Line Package. For PLCC pin assignment, see the Pin Conversion Tables on page 6–11 of the Motorola MECL Data Book (DL122/D). 9/96 Motorola, Inc. 1996 2–57 REV 6 MC10H350 ELECTRICAL CHARACTERISTICS (VCC = 5.0 V ±5%) (See Notes 1 & 4) TA = 0°C to 75°C Characteristic Symbol Min Max Unit AC PARAMETERS (CL = 50 pF) (VCC = 5.0 ± 5%) (TA = 0°C to 75°C) Propagation Delay Data tpd 1.5 5.0 ns Rise Time tr 0.3 1.6 ns Fall Time tf 0.3 1.6 ns Output Disable Time tpdLZ tpdHZ 2.0 2.0 6.0 6.0 ns Output Enable Time tpdZL tpdZH 2.0 2.0 8.0 8.0 ns 3–STATE SWITCHING WAVEFORMS 3–STATE OUTPUT LOW ENABLE AND DISABLE TIMES 3–STATE OUTPUT HIGH ENABLE AND DISABLE TIMES OE OE 1.5 V 1.5 V TPZL VOUT 1.5 V TPLZ 1.5 V TPZH TPHZ Q VOH ≈ 3.5 V 1.5 V 1.5 V VOUT VOL 0.3 V 0.3 V TEST LOAD +7.0 V OPEN TPZL, TPLZ, O, C, ALL OTHER 500 Ω D.U.T . 500 Ω 50 PF *INCLUDES JIG AND PROBE CAPACITANCE Application Note: Pin 9 is an OE and the 10H350 is disabled when OE is at VIH or higher. MOTOROLA 2–58 MECL Data DL122 — Rev 6 MC10H350 OUTLINE DIMENSIONS FN SUFFIX PLASTIC PLCC PACKAGE CASE 775–02 ISSUE C 0.007 (0.180) M T L–M B Y BRK –N– U N S 0.007 (0.180) M T L–M S S N S D –L– –M– Z W 20 D 1 V 0.010 (0.250) G1 X S T L–M S N S VIEW D–D A 0.007 (0.180) M T L–M S N S R 0.007 (0.180) M T L–M S N S Z C H –T– SEATING PLANE F VIEW S G1 0.010 (0.250) S T L–M S 0.007 (0.180) M T L–M S N S VIEW S S N S NOTES: 1. DATUMS –L–, –M–, AND –N– DETERMINED WHERE TOP OF LEAD SHOULDER EXITS PLASTIC BODY AT MOLD PARTING LINE. 2. DIMENSION G1, TRUE POSITION TO BE MEASURED AT DATUM –T–, SEATING PLANE. 3. DIMENSIONS R AND U DO NOT INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH IS 0.010 (0.250) PER SIDE. 4. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 5. CONTROLLING DIMENSION: INCH. 6. THE PACKAGE TOP MAY BE SMALLER THAN THE PACKAGE BOTTOM BY UP TO 0.012 (0.300). DIMENSIONS R AND U ARE DETERMINED AT THE OUTERMOST EXTREMES OF THE PLASTIC BODY EXCLUSIVE OF MOLD FLASH, TIE BAR BURRS, GATE BURRS AND INTERLEAD FLASH, BUT INCLUDING ANY MISMATCH BETWEEN THE TOP AND BOTTOM OF THE PLASTIC BODY. 7. DIMENSION H DOES NOT INCLUDE DAMBAR PROTRUSION OR INTRUSION. THE DAMBAR PROTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE GREATER THAN 0.037 (0.940). THE DAMBAR INTRUSION(S) SHALL NOT CAUSE THE H DIMENSION TO BE SMALLER THAN 0.025 (0.635). MECL Data DL122 — Rev 6 N K 0.004 (0.100) J S K1 E G 0.007 (0.180) M T L–M 2–59 DIM A B C E F G H J K R U V W X Y Z G1 K1 INCHES MIN MAX 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 BSC 0.026 0.032 0.020 ––– 0.025 ––– 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 ––– 0.020 2_ 10 _ 0.310 0.330 0.040 ––– MILLIMETERS MIN MAX 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 BSC 0.66 0.81 0.51 ––– 0.64 ––– 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 ––– 0.50 2_ 10 _ 7.88 8.38 1.02 ––– MOTOROLA MC10H350 OUTLINE DIMENSIONS L SUFFIX CERAMIC DIP PACKAGE CASE 620–10 ISSUE V –A– 16 9 1 8 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION F MAY NARROW TO 0.76 (0.030) WHERE THE LEAD ENTERS THE CERAMIC BODY. –B– C L DIM A B C D E F G H K L M N –T– K N SEATING PLANE M E F J G D 16 PL 0.25 (0.010) 16 PL 0.25 (0.010) M T A T B M –A– 9 1 8 B F C L S –T– SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M MILLIMETERS MIN MAX 19.05 19.93 6.10 7.49 ––– 5.08 0.39 0.50 1.27 BSC 1.40 1.65 2.54 BSC 0.21 0.38 3.18 4.31 7.62 BSC 0_ 15 _ 0.51 1.01 S P SUFFIX PLASTIC DIP PACKAGE CASE 648–08 ISSUE R 16 S INCHES MIN MAX 0.750 0.785 0.240 0.295 ––– 0.200 0.015 0.020 0.050 BSC 0.055 0.065 0.100 BSC 0.008 0.015 0.125 0.170 0.300 BSC 0_ 15 _ 0.020 0.040 T A M NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. DIM A B C D F G H J K L M S INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0_ 10 _ 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0_ 10 _ 0.51 1.01 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 MFAX: [email protected] – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ MOTOROLA 2–60 *MC10H350/D* MC10H350/D MECL Data DL122 — Rev 6