SHARP LH28F160BJE

Date
16M (x8/x16) Flash Memory
LH28F160BJE-TTL90
Mar. 16. 2000
LHF16J02
●Handle this document carefully for it contains material protected by international copyright law.
Any reproduction, full or in part, of this material is prohibited without the express written
permission of the company.
●When using the products covered herein, please observe the conditions written herein and the
precautions outlined in the following paragraphs. In no event shall the company be liable for any
damages resulting from failure to strictly adhere to these conditions and precautions.
(1) The products covered herein are designed and manufactured for the following application
areas. When using the products covered herein for the equipment listed in Paragraph (2),
even for the following application areas, be sure to observe the precautions given in
Paragraph (2). Never use the products for the equipment listed in Paragraph (3).
•Office electronics
•Instrumentation and measuring equipment
•Machine tools
•Audiovisual equipment
•Home appliance
•Communication equipment other than for trunk lines
(2) Those contemplating using the products covered herein for the following equipment which
demands high reliability, should first contact a sales representative of the company and then
accept responsibility for incorporating into the design fail-safe operation, redundancy, and
other appropriate measures for ensuring reliability and safety of the equipment and the
overall system.
•Control and safety devices for airplanes, trains, automobiles, and other
transportation equipment
•Mainframe computers
•Traffic control systems
•Gas leak detectors and automatic cutoff devices
•Rescue and security equipment
•Other safety devices and safety equipment, etc.
(3) Do not use the products covered herein for the following equipment which demands
extremely high performance in terms of functionality, reliability, or accuracy.
•Aerospace equipment
•Communications equipment for trunk lines
•Control equipment for the nuclear power industry
•Medical equipment related to life support, etc.
(4) Please direct all queries and comments regarding the interpretation of the above three
Paragraphs to a sales representative of the company.
●Please direct all queries regarding the products covered herein to a sales representative of the
company.
Rev. 1.26
LHF16J02
1
CONTENTS
PAGE
PAGE
1 INTRODUCTION.............................................................. 3
5 DESIGN CONSIDERATIONS ....................................... 25
1.1 Features ........................................................................ 3
5.1 Three-Line Output Control ........................................ 25
1.2 Product Overview......................................................... 3
5.2 RY/BY# and WSM Polling ....................................... 25
1.3 Product Description...................................................... 4
5.3 Power Supply Decoupling ......................................... 25
1.3.1 Package Pinout ....................................................... 4
5.4 VCCW Trace on Printed Circuit Boards ..................... 25
1.3.2 Block Organization................................................. 4
5.5 VCC, VCCW, RP# Transitions .................................... 25
5.6 Power-Up/Down Protection....................................... 26
2 PRINCIPLES OF OPERATION........................................ 7
5.7 Power Dissipation ...................................................... 26
2.1 Data Protection............................................................. 8
5.8 Data Protection Method ............................................. 26
3 BUS OPERATION ............................................................ 8
6 ELECTRICAL SPECIFICATIONS ................................ 27
3.1 Read.............................................................................. 8
6.1 Absolute Maximum Ratings ...................................... 27
3.2 Output Disable.............................................................. 8
6.2 Operating Conditions ................................................. 27
3.3 Standby......................................................................... 8
6.2.1 Capacitance .......................................................... 27
3.4 Reset............................................................................. 8
6.2.2 AC Input/Output Test Conditions ........................ 28
3.5 Read Identifier Codes................................................... 9
6.2.3 DC Characteristics ............................................... 29
3.6 Write............................................................................. 9
6.2.4 AC Characteristics - Read-Only Operations ........ 31
6.2.5 AC Characteristics - Write Operations ................ 34
4 COMMAND DEFINITIONS............................................. 9
6.2.6 Alternative CE#-Controlled Writes...................... 36
4.1 Read Array Command................................................ 12
6.2.7 Reset Operations .................................................. 38
4.2 Read Identifier Codes Command ............................... 12
6.2.8 Block Erase, Full Chip Erase, Word/Byte Write and
4.3 Read Status Register Command ................................. 12
Lock-Bit Configuration Performance ................. 39
4.4 Clear Status Register Command................................. 12
4.5 Block Erase Command............................................... 13
4.6 Full Chip Erase Command ......................................... 13
4.7 Word/Byte Write Command....................................... 13
4.8 Block Erase Suspend Command ................................ 14
4.9 Word/Byte Write Suspend Command ........................ 14
4.10 Set Block and Permanent Lock-Bit Command......... 15
4.11 Clear Block Lock-Bits Command ............................ 15
4.12 Block Locking by the WP# ...................................... 16
Rev. 1.26
LHF16J02
2
LH28F160BJE-TTL90
16M-BIT ( 1Mbit ×16 / 2Mbit ×8 )
Boot Block Flash MEMORY
■ Low Voltage Operation
VCC=VCCW=2.7V-3.6V Single Voltage
■ User-Configurable ×8 or ×16 Operation
■ High-Performance Read Access Time
90ns(VCC=2.7V-3.6V)
■ Operating Temperature
0°C to +70°C
■ Low Power Management
Typ. 2µA (VCC=3.0V) Standby Current
Automatic Power Savings Mode Decreases ICCR in
Static Mode
Typ. 120µA (VCC=3.0V, TA=+25°C, f=32kHz)
Read Current
■ Optimized Array Blocking Architecture
Two 4K-word (8K-byte) Boot Blocks
Six 4K-word (8K-byte) Parameter Blocks
Thirty-one 32K-word (64K-byte) Main Blocks
Top Boot Location
■ Extended Cycling Capability
Minimum 100,000 Block Erase Cycles
■ Enhanced Automated Suspend Options
Word/Byte Write Suspend to Read
Block Erase Suspend to Word/Byte Write
Block Erase Suspend to Read
■ Enhanced Data Protection Features
Absolute Protection with VCCW≤VCCWLK
Block Erase, Full Chip Erase, Word/Byte Write and
Lock-Bit Configuration Lockout during Power
Transitions
Block Locking with Command and WP#
Permanent Locking
■ Automated Block Erase, Full Chip Erase,
Word/Byte Write and Lock-Bit Configuration
Command User Interface (CUI)
Status Register (SR)
■ SRAM-Compatible Write Interface
■ Industry-Standard Packaging
48-Lead TSOP
■ ETOXTM* Nonvolatile Flash Technology
■ CMOS Process (P-type silicon substrate)
■ Not designed or rated as radiation hardened
SHARP’s LH28F160BJE-TTL90 Flash memory is a high-density, low-cost, nonvolatile, read/write storage solution for a wide
range of applications.
LH28F160BJE-TTL90 can operate at VCC=2.7V-3.6V and VCCW=2.7V-3.6V or 11.7V-12.3V. Its low voltage operation
capability realize battery life and suits for cellular phone application.
Its Boot, Parameter and Main-blocked architecture, low voltage and extended cycling provide for highly flexible component
suitable for portable terminals and personal computers. Its enhanced suspend capabilities provide for an ideal solution for code
+ data storage applications.
For secure code storage applications, such as networking, where code is either directly executed out of flash or downloaded to
DRAM, the LH28F160BJE-TTL90 offers four levels of protection: absolute protection with VCCW≤VCCWLK, selective
hardware block locking or flexible software block locking. These alternatives give designers ultimate control of their code
security needs.
The LH28F160BJE-TTL90 is manufactured on SHARP’s 0.25µm ETOXTM* process technology. It come in industry-standard
package: the 48-lead TSOP, ideal for board constrained applications.
*ETOX is a trademark of Intel Corporation.
Rev. 1.26
LHF16J02
1 INTRODUCTION
This
datasheet
contains
LH28F160BJE-TTL90
specifications. Section 1 provides a flash memory
overview. Sections 2, 3, 4 and 5 describe the memory
organization and functionality. Section 6 covers electrical
specifications.
1.1 Features
Key enhancements of LH28F160BJE-TTL90 boot block
Flash memory are:
•Single low voltage operation
•Low power consumption
•Enhanced Suspend Capabilities
•Boot Block Architecture
Please note following:
•VCCWLK has been lowered to 1.0V to support 2.7V3.6V block erase, full chip erase, word/byte write and
lock-bit configuration operations. The VCCW voltage
transitions to GND is recommended for designs that
switch VCCW off during read operation.
1.2 Product Overview
The LH28F160BJE-TTL90 is a high-performance 16M-bit
Boot Block Flash memory organized as 1M-word of 16
bits or 2M-byte of 8 bits. The 1M-word/2M-byte of data is
arranged in two 4K-word/8K-byte boot blocks, six 4Kword/8K-byte parameter blocks and thirty-one 32Kword/64K-byte main blocks which are individually
erasable, lockable and unlockable in-system. The memory
map is shown in Figure 3.
The dedicated VCCW pin gives complete data protection
when VCCW≤VCCWLK.
A Command User Interface (CUI) serves as the interface
between the system processor and internal operation of the
device. A valid command sequence written to the CUI
initiates device automation. An internal Write State
Machine (WSM) automatically executes the algorithms
and timings necessary for block erase, full chip erase,
word/byte write and lock-bit configuration operations.
3
A block erase operation erases one of the device’s 32Kword/64K-byte blocks typically within 1.2s (3V VCC, 3V
VCCW), 4K-word/8K-byte blocks typically within 0.6s (3V
VCC, 3V VCCW) independent of other blocks. Each block
can be independently erased minimum 100,000 times.
Block erase suspend mode allows system software to
suspend block erase to read or write data from any other
block.
Writing memory data is performed in word/byte
increments of the device’s 32K-word blocks typically
within 33µs (3V VCC, 3V VCCW), 64K-byte blocks
typically within 31µs (3V VCC, 3V VCCW), 4K-word
blocks typically within 36µs (3V VCC, 3V VCCW), 8Kbyte blocks typically within 32µs (3V VCC, 3V VCCW).
Word/byte write suspend mode enables the system to read
data or execute code from any other flash memory array
location.
Individual block locking uses a combination of bits, thirtynine block lock-bits, a permanent lock-bit and WP# pin, to
lock and unlock blocks. Block lock-bits gate block erase,
full chip erase and word/byte write operations, while the
permanent lock-bit gates block lock-bit modification and
locked block alternation. Lock-bit configuration
operations (Set Block Lock-Bit, Set Permanent Lock-Bit
and Clear Block Lock-Bits commands) set and cleared
lock-bits.
The status register indicates when the WSM’s block erase,
full chip erase, word/byte write or lock-bit configuration
operation is finished.
The RY/BY# output gives an additional indicator of WSM
activity by providing both a hardware signal of status
(versus software polling) and status masking (interrupt
masking for background block erase, for example). Status
polling using RY/BY# minimizes both CPU overhead and
system power consumption. When low, RY/BY# indicates
that the WSM is performing a block erase, full chip erase,
word/byte write or lock-bit configuration. RY/BY#-high Z
indicates that the WSM is ready for a new command,
block erase is suspended (and word/byte write is
inactive), word/byte write is suspended, or the device is in
reset mode.
Rev. 1.26
LHF16J02
4
The access time is 90ns (tAVQV) over the operating
temperature range (0°C to +70°C) and VCC supply voltage
range of 2.7V-3.6V.
1.3 Product Description
The Automatic Power Savings (APS) feature substantially
reduces active current when the device is in static mode
(addresses not switching). In APS mode, the typical ICCR
current is 2µA (CMOS) at 3.0V VCC.
LH28F160BJE-TTL90 Boot Block Flash memory is
available in 48-lead TSOP package (see Figure 2).
When CE# and RP# pins are at VCC, the ICC CMOS
standby mode is enabled. When the RP# pin is at GND,
reset mode is enabled which minimizes power
consumption and provides write protection. A reset time
(tPHQV) is required from RP# switching high until outputs
are valid. Likewise, the device has a wake time (tPHEL)
from RP#-high until writes to the CUI are recognized.
With RP# at GND, the WSM is reset and the status
register is cleared.
Please do not execute reprogramming "0" for the bit which
has already been programed "0". Overwrite operation may
generate unerasable bit. In case of reprogramming "0" to
the data which has been programed "1".
·Program "0" for the bit in which you want to change
data from "1" to "0".
·Program "1" for the bit which has already been
programmed "0".
For example, changing data from "10111101" to
"10111100" requires "11111110" programming.
1.3.1 Package Pinout
1.3.2 Block Organization
This product features an asymmetrically-blocked
architecture providing system memory integration. Each
erase block can be erased independently of the others up to
100,000 times. For the address locations of the blocks, see
the memory map in Figure 3.
Boot Blocks: The boot block is intended to replace a
dedicated boot PROM in a microprocessor or
microcontroller-based system. This boot block 4K words
(4,096words) features hardware controllable writeprotection to protect the crucial microprocessor boot code
from accidental modification. The protection of the boot
block is controlled using a combination of the VCCW, RP#,
WP# pins and block lock-bit.
Parameter Blocks: The boot block architecture includes
parameter blocks to facilitate storage of frequently update
small parameters that would normally require an
EEPROM. By using software techniques, the word-rewrite
functionality of EEPROMs can be emulated. Each boot
block component contains six parameter blocks of 4K
words (4,096 words) each. The protection of the parameter
block is controlled using a combination of the VCCW, RP#
and block lock-bit.
Main Blocks: The reminder is divided into main blocks for
data or code storage. Each 16M-bit device contains thirtyone 32K words (32,768 words) blocks. The protection of
the main block is controlled using a combination of the
VCCW, RP# and block lock-bit.
Rev. 1.26
LHF16J02
5
DQ0-DQ15
Input
Buffer
Output
Buffer
I/O
Logic
Status
Register
Data
Register
Output
Multiplexer
Identifier
Register
VCC
BYTE#
CE#
WE#
Command
User
Interface
OE#
RP#
WP#
Data
Comparator
Address
Counter
32K-Word
(64K-Byte)
Main Blocks
×31
Main Block 29
X
Decoder
Write
State
Machine
RY/BY#
Program/Erase
Voltage Switch
Main Block 30
Address
Latch
Y-Gating
Main Block 1
Y
Decoder
Main Block 0
Input
Buffer
Boot Block 0
Boot Block 1
Parameter Block 0
Parameter Block 1
Parameter Block 2
Parameter Block 3
Parameter Block 4
Parameter Block 5
A-1-A19
VCCW
VCC
GND
Figure 1. Block Diagram
A15
A14
A13
A12
A11
A10
A9
A8
A19
NC
WE#
RP#
VCCW
WP#
RY/BY#
A18
A17
A7
A6
A5
A4
A3
A2
A1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
48-LEAD TSOP
STANDARD PINOUT
12mm x 20mm
TOP VIEW
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
A16
BYTE#
GND
DQ15/A-1
DQ7
DQ14
DQ6
DQ13
DQ5
DQ12
DQ4
VCC
DQ11
DQ3
DQ10
DQ2
DQ9
DQ1
DQ8
DQ0
OE#
GND
CE#
A0
Figure 2. TSOP 48-Lead Pinout
Rev. 1.26
LHF16J02
Symbol
Type
A-1
A0-A19
INPUT
DQ0-DQ15
INPUT/
OUTPUT
CE#
INPUT
RP#
INPUT
OE#
INPUT
WE#
INPUT
WP#
INPUT
BYTE#
INPUT
RY/BY#
OPEN
DRAIN
OUTPUT
VCCW
SUPPLY
VCC
SUPPLY
GND
NC
SUPPLY
6
Table 1. Pin Descriptions
Name and Function
ADDRESS INPUTS: Inputs for addresses during read and write operations. Addresses are
internally latched during a write cycle.
A-1: Lower address input while BYTE# is VIL. A-1 pin changes DQ15 pin while BYTE# is VIH.
A15-A19: Main Block Address.
A12-A19: Boot and Parameter Block Address.
DATA INPUT/OUTPUTS: Inputs data and commands during CUI write cycles; outputs data
during memory array, status register and identifier code read cycles. Data pins float to highimpedance when the chip is deselected or outputs are disabled. Data is internally latched during a
write cycle. DQ8-DQ15 pins are not used while byte mode (BYTE#=VIL). Then, DQ15 pin
changes A-1 address input.
CHIP ENABLE: Activates the device’s control logic, input buffers, decoders and sense amplifiers.
CE#-high deselects the device and reduces power consumption to standby levels.
RESET: Resets the device internal automation. RP#-high enables normal operation. When driven
low, RP# inhibits write operations which provides data protection during power transitions. Exit
from reset mode sets the device to read array mode. RP# must be VIL during power-up.
OUTPUT ENABLE: Gates the device’s outputs during a read cycle.
WRITE ENABLE: Controls writes to the CUI and array blocks. Addresses and data are latched on
the rising edge of the WE# pulse.
WRITE PROTECT: When WP# is VIL, boot blocks cannot be written or erased. When WP# is
VIH, locked boot blocks can not be written or erased. WP# is not affected parameter and main
blocks.
BYTE ENABLE: BYTE# VIL places device in byte mode (×8). All data is then input or output on
DQ0-7, and DQ8-15 float. BYTE# VIH places the device in word mode (×16), and turns off the A-1
input buffer.
READY/BUSY#: Indicates the status of the internal WSM. When low, the WSM is performing an
internal operation (block erase, full chip erase, word/byte write or lock-bit configuration).
RY/BY#-high Z indicates that the WSM is ready for new commands, block erase is suspended,
and word/byte write is inactive, word/byte write is suspended, or the device is in reset mode.
BLOCK ERASE, FULL CHIP ERASE, WORD/BYTE WRITE OR LOCK-BIT
CONFIGURATION POWER SUPPLY: For erasing array blocks, writing words/bytes or
configuring lock-bits. With VCCW≤VCCWLK, memory contents cannot be altered. Block erase, full
chip erase, word/byte write and lock-bit configuration with an invalid VCCW (see 6.2.3 DC
Characteristics) produce spurious results and should not be attempted. Applying 12V±0.3V to
VCCW during erase/write can only be done for a maximum of 1000 cycles on each block. VCCW
may be connected to 12V±0.3V for a total of 80 hours maximum.
DEVICE POWER SUPPLY: Do not float any power pins. With VCC≤VLKO, all write attempts to
the flash memory are inhibited. Device operations at invalid VCC voltage (see 6.2.3 DC
Characteristics) produce spurious results and should not be attempted.
GROUND: Do not float any ground pins.
NO CONNECT: Lead is not internal connected; it may be driven or floated.
Rev. 1.26
LHF16J02
7
2 PRINCIPLES OF OPERATION
[A19-A0]
The LH28F160BJE-TTL90 flash memory includes an onchip WSM to manage block erase, full chip erase,
word/byte write and lock-bit configuration functions. It
allows for: 100% TTL-level control inputs, fixed power
supplies during block erase, full chip erase, word/byte
write and lock-bit configuration, and minimal processor
overhead with RAM-like interface timings.
After initial device power-up or return from reset mode
(see section 3 Bus Operations), the device defaults to read
array mode. Manipulation of external memory control pins
allow array read, standby and output disable operations.
Status register and identifier codes can be accessed
through the CUI independent of the VCCW voltage. High
voltage on VCCW enables successful block erase, full chip
erase, word/byte write and lock-bit configurations. All
functions associated with altering memory contents−block
erase, full chip erase, word/byte write, lock-bit
configuration, status and identifier codes−are accessed via
the CUI and verified through the status register.
Commands are written using standard microprocessor
write timings. The CUI contents serve as input to the
WSM, which controls the block erase, full chip erase,
word/byte write and lock-bit configuration. The internal
algorithms are regulated by the WSM, including pulse
repetition, internal verification and margining of data.
Addresses and data are internally latched during write
cycles. Writing the appropriate command outputs array
data, accesses the identifier codes or outputs status register
data.
Interface software that initiates and polls progress of block
erase, full chip erase, word/byte write and lock-bit
configuration can be stored in any block. This code is
copied to and executed from system RAM during flash
memory updates. After successful completion, reads are
again possible via the Read Array command. Block erase
suspend allows system software to suspend a block erase
to read/write data from/to blocks other than that which is
suspend. Word/byte write suspend allows system software
to suspend a word/byte write to read data from any other
flash memory array location.
FFFFF
FF000
FEFFF
FE000
FDFFF
FD000
FCFFF
FC000
FBFFF
FB000
FAFFF
FA000
F9FFF
F9000
F8FFF
F8000
F7FFF
F0000
EFFFF
E8000
E7FFF
E0000
DFFFF
D8000
D7FFF
D0000
CFFFF
C8000
C7FFF
C0000
BFFFF
B8000
B7FFF
B0000
AFFFF
A8000
A7FFF
A0000
9FFFF
98000
97FFF
90000
8FFFF
88000
87FFF
80000
7FFFF
78000
77FFF
70000
6FFFF
68000
67FFF
60000
5FFFF
58000
57FFF
50000
4FFFF
48000
47FFF
40000
3FFFF
38000
37FFF
30000
2FFFF
28000
27FFF
20000
1FFFF
18000
17FFF
10000
0FFFF
08000
07FFF
00000
Top Boot
4KW/8KB Boot Block
[A19-A-1]
0
4KW/8KB Boot Block
1
4KW/8KB Parameter Block
0
4KW/8KB Parameter Block
1
4KW/8KB Parameter Block
2
4KW/8KB Parameter Block
3
4KW/8KB Parameter Block
4
4KW/8KB Parameter Block
5
32KW/64KB Main Block
0
32KW/64KB Main Block
1
32KW/64KB Main Block
2
32KW/64KB Main Block
3
32KW/64KB Main Block
4
32KW/64KB Main Block
5
32KW/64KB Main Block
6
32KW/64KB Main Block
7
32KW/64KB Main Block
8
32KW/64KB Main Block
9
32KW/64KB Main Block
10
32KW/64KB Main Block
11
32KW/64KB Main Block
12
32KW/64KB Main Block
13
32KW/64KB Main Block
14
32KW/64KB Main Block
15
32KW/64KB Main Block
16
32KW/64KB Main Block
17
32KW/64KB Main Block
18
32KW/64KB Main Block
19
32KW/64KB Main Block
20
32KW/64KB Main Block
21
32KW/64KB Main Block
22
32KW/64KB Main Block
23
32KW/64KB Main Block
24
32KW/64KB Main Block
25
32KW/64KB Main Block
26
32KW/64KB Main Block
27
32KW/64KB Main Block
28
32KW/64KB Main Block
29
32KW/64KB Main Block
30
1FFFFF
1FE000
1FDFFF
1FC000
1FBFFF
1FA000
1F9FFF
1F8000
1F7FFF
1F6000
1F5FFF
1F4000
1F3FFF
1F2000
1F1FFF
1F0000
1EFFFF
1E0000
1DFFFF
1D0000
1CFFFF
1C0000
1BFFFF
1B0000
1AFFFF
1A0000
19FFFF
190000
18FFFF
180000
17FFFF
170000
16FFFF
160000
15FFFF
150000
14FFFF
140000
13FFFF
130000
12FFFF
120000
11FFFF
110000
10FFFF
100000
0FFFFF
0F0000
0EFFFF
0E0000
0DFFFF
0D0000
0CFFFF
0C0000
0BFFFF
0B0000
0AFFFF
0A0000
09FFFF
090000
08FFFF
080000
07FFFF
070000
06FFFF
060000
05FFFF
050000
04FFFF
040000
03FFFF
030000
02FFFF
020000
01FFFF
010000
00FFFF
000000
Figure 3. Memory Map
Rev. 1.26
LHF16J02
8
2.1 Data Protection
3.3 Standby
When VCCW≤VCCWLK, memory contents cannot be
altered. The CUI, with two-step block erase, full chip
erase, word/byte write or lock-bit configuration command
sequences, provides protection from unwanted operations
even when high voltage is applied to VCCW. All write
functions are disabled when VCC is below the write
lockout voltage VLKO or when RP# is at VIL. The device’s
block locking capability provides additional protection
from inadvertent code or data alteration by gating block
erase, full chip erase and word/byte write operations.
Refer to Table 5 for write protection alternatives.
CE# at a logic-high level (VIH) places the device in
standby mode which substantially reduces device power
consumption. DQ0-DQ15 outputs are placed in a highimpedance state independent of OE#. If deselected during
block erase, full chip erase, word/byte write or lock-bit
configuration, the device continues functioning, and
consuming active power until the operation completes.
3 BUS OPERATION
In read modes, RP#-low deselects the memory, places
output drivers in a high-impedance state and turns off all
internal circuits. RP# must be held low for a minimum of
100ns. Time tPHQV is required after return from reset
mode until initial memory access outputs are valid. After
this wake-up interval, normal operation is restored. The
CUI is reset to read array mode and status register is set to
80H.
The local CPU reads and writes flash memory in-system.
All bus cycles to or from the flash memory conform to
standard microprocessor bus cycles.
3.1 Read
Information can be read from any block, identifier codes
or status register independent of the VCCW voltage. RP#
can be at VIH.
The first task is to write the appropriate read mode
command (Read Array, Read Identifier Codes or Read
Status Register) to the CUI. Upon initial device power-up
or after exit from reset mode, the device automatically
resets to read array mode. Six control pins dictate the data
flow in and out of the component: CE#, OE#, BYTE#,
WE#, RP# and WP#. CE# and OE# must be driven active
to obtain data at the outputs. CE# is the device selection
control, and when active enables the selected memory
device. OE# is the data output (DQ0-DQ15) control and
when active drives the selected memory data onto the I/O
bus. BYTE# is the device I/O interface mode control.
WE# must be at VIH, RP# must be at VIH, and BYTE#
and WP# must be at VIL or VIH. Figure 14, 15 illustrates
read cycle.
3.2 Output Disable
3.4 Reset
RP# at VIL initiates the reset mode.
During block erase, full chip erase, word/byte write or
lock-bit configuration modes, RP#-low will abort the
operation. RY/BY# remains low until the reset operation
is complete. Memory contents being altered are no longer
valid; the data may be partially erased or written. Time
tPHWL is required after RP# goes to logic-high (VIH)
before another command can be written.
As with any automated device, it is important to assert
RP# during system reset. When the system comes out of
reset, it expects to read from the flash memory. Automated
flash memories provide status information when accessed
during block erase, full chip erase, word/byte write or
lock-bit configuration modes. If a CPU reset occurs with
no flash memory reset, proper CPU initialization may not
occur because the flash memory may be providing status
information instead of array data. SHARP’s flash
memories allow proper CPU initialization following a
system reset through the use of the RP# input. In this
application, RP# is controlled by the same RESET# signal
that resets the system CPU.
With OE# at a logic-high level (VIH), the device outputs
are disabled. Output pins (DQ0-DQ15) are placed in a
high-impedance state.
Rev. 1.26
LHF16J02
9
3.5 Read Identifier Codes
The read identifier codes operation outputs the
manufacturer code, device code, block lock configuration
codes for each block and the permanent lock configuration
code (see Figure 4). Using the manufacturer and device
codes, the system CPU can automatically match the device
with its proper algorithms. The block lock and permanent
lock configuration codes identify locked and unlocked
blocks and permanent lock-bit setting.
3.6 Write
Writing commands to the CUI enable reading of device
data and identifier codes. They also control inspection and
clearing of the status register. When VCC=2.7V-3.6V and
VCCW=VCCWH1/2, the CUI additionally controls block
erase, full chip erase, word/byte write and lock-bit
configuration.
[A19-A0]*
FFFFF
Reserved for Future Implementation
FF003
FF002
FF001
FF000
The CUI does not occupy an addressable memory
location. It is written when WE# and CE# are active. The
address and data needed to execute a command are latched
on the rising edge of WE# or CE# (whichever goes high
first). Standard microprocessor write timings are used.
Figures 16 and 17 illustrate WE# and CE# controlled write
operations.
Boot Block 0 Lock Configuration Code
Reserved for Future Implementation
Boot Block 0
FEFFF
Reserved for Future Implementation
FE003
FE002
FE001
FE000
Boot Block 1 Lock Configuration Code
Reserved for Future Implementation
Boot Block 1
FDFFF
Reserved for Future Implementation
FD003
FD002
The Block Erase command requires appropriate command
data and an address within the block to be erased. The Full
Chip Erase command requires appropriate command data
and an address within the device. The Word/Byte Write
command requires the command and address of the
location to be written. Set Permanent and Block Lock-Bit
commands require the command and address within the
device (Permanent Lock) or block within the device
(Block Lock) to be locked. The Clear Block Lock-Bits
command requires the command and address within the
device.
Top Boot
FD001
FD000
FCFFF
F9000
Parameter Block 0 Lock Configuration Code
Reserved for Future Implementation
Parameter Block 0
(Parameter Blocks 1 through 4)
F8FFF
Reserved for Future Implementation
F8003
F8002
F8001
F8000
Parameter Block 5 Lock Configuration Code
Reserved for Future Implementation
Parameter Block 5
F7FFF
Reserved for Future Implementation
F0003
F0002
F0001
F0000
EFFFF
08000
4 COMMAND DEFINITIONS
07FFF
When the VCCW voltage ≤VCCWLK, read operations from
the status register, identifier codes, or blocks are enabled.
Placing VCCWH1/2 on VCCW enables successful block
erase, full chip erase, word/byte write and lock-bit
configuration operations.
00004
Main Block 0 Lock Configuration Code
Reserved for Future Implementation
Main Block 0
(Main Blocks 1 through 29)
Reserved for Future Implementation
Device operations are selected by writing specific
commands into the CUI. Table 3 defines these commands.
00003
00002
00001
00000
*:
Permanent Lock Configuration Code
Main Block 30 Lock Configuration Code
Device Code
Manufacturer Code Main Block 30
Address A-1 don’t care.
Figure 4. Device Identifier Code Memory Map
Rev. 1.26
LHF16J02
Mode
Read
Output Disable
Standby
Reset
Read Identifier Codes
Write
Mode
Read
Output Disable
Standby
Reset
Read Identifier Codes
Notes
8
4
Table 2.1.
RP#
VIH
VIH
VIH
VIL
8
VIH
6,7,8
VIH
Notes
8
4
8
Table 2.2.
RP#
VIH
VIH
VIH
VIL
VIH
Bus Operations (BYTE#=VIH)(1,2)
CE#
OE#
WE#
Address
VIL
VIL
VIH
X
VIL
VIH
VIH
X
VIH
X
X
X
X
X
X
X
See
VIL
VIL
VIH
Figure 4
VIL
VIH
VIL
X
Bus Operations (BYTE#=VIL)(1,2)
CE#
OE#
WE#
Address
VIL
VIL
VIH
X
VIL
VIH
VIH
X
VIH
X
X
X
X
X
X
X
See
VIL
VIL
VIH
Figure 4
VIL
VIH
VIL
X
10
VCCW
X
X
X
X
DQ0-15
DOUT
High Z
High Z
High Z
RY/BY#(3)
X
X
X
High Z
X
Note 5
High Z
X
DIN
X
VCCW
X
X
X
X
DQ0-7
DOUT
High Z
High Z
High Z
RY/BY#(3)
X
X
X
High Z
X
Note 5
High Z
Write
6,7,8
VIH
X
DIN
X
NOTES:
1. Refer to DC Characteristics. When VCCW≤VCCWLK, memory contents can be read, but not altered.
2. X can be VIL or VIH for control pins and addresses, and VCCWLK or VCCWH1/2 for VCCW. See DC Characteristics for
VCCWLK voltages.
3. RY/BY# is VOL when the WSM is executing internal block erase, full chip erase, word/byte write or lock-bit configuration
algorithms. It is High Z during when the WSM is not busy, in block erase suspend mode (with word/byte write inactive),
word/byte write suspend mode or reset mode.
4. RP# at GND±0.2V ensures the lowest power consumption.
5. See Section 4.2 for read identifier code data.
6. Command writes involving block erase, full chip erase, word/byte write or lock-bit configuration are reliably executed
when VCCW=VCCWH1/2 and VCC=2.7V-3.6V.
7. Refer to Table 3 for valid DIN during a write operation.
8. Never hold OE# low and WE# low at the same timing.
Rev. 1.26
LHF16J02
Command
Read Array/Reset
Read Identifier Codes
Read Status Register
Clear Status Register
Block Erase
Full Chip Erase
Word/Byte Write
Table 3. Command Definitions(10)
Bus Cycles
First Bus Cycle
(1)
Req’d.
Notes
Oper
Addr(2)
Data(3)
1
Write
X
FFH
4
Write
X
90H
≥2
2
Write
X
70H
1
Write
X
50H
2
5
Write
X
20H
2
Write
X
30H
40H or
2
5,6
Write
X
10H
11
Second Bus Cycle
Addr(2)
Data(3)
Oper(1)
Read
Read
IA
X
ID
SRD
Write
Write
BA
X
D0H
D0H
Write
WA
WD
Block Erase and Word/Byte
1
5
Write
X
B0H
Write Suspend
Block Erase and Word/Byte
1
5
Write
X
D0H
Write Resume
Set Block Lock-Bit
2
8
Write
X
60H
Write
BA
01H
Clear Block Lock-Bits
2
7,8
Write
X
60H
Write
X
D0H
Set Permanent Lock-Bit
2
9
Write
X
60H
Write
X
F1H
NOTES:
1. BUS operations are defined in Table 2.1 and Table 2.2.
2. X=Any valid address within the device.
IA=Identifier Code Address: see Figure 4.
BA=Address within the block being erased.
WA=Address of memory location to be written.
3. SRD=Data read from status register. See Table 6 for a description of the status register bits.
WD=Data to be written at location WA. Data is latched on the rising edge of WE# or CE# (whichever goes high first).
ID=Data read from identifier codes.
4. Following the Read Identifier Codes command, read operations access manufacturer, device, block lock configuration and
permanent lock configuration codes. See Section 4.2 for read identifier code data.
5. If WP# is VIL, boot blocks are locked without block lock-bits state. If WP# is VIH, boot blocks are locked by block lockbits. The parameter and main blocks are locked by block lock-bits without WP# state.
6. Either 40H or 10H are recognized by the WSM as the word/byte write setup.
7. The clear block lock-bits operation simultaneously clears all block lock-bits.
8. If the permanent lock-bit is set, Set Block Lock-Bit and Clear Block Lock-Bits commands can not be done.
9. Once the permanent lock-bit is set, permanent lock-bit reset is unable.
10. Commands other than those shown above are reserved by SHARP for future device implementations and should not be
used.
Rev. 1.26
LHF16J02
12
4.1 Read Array Command
4.3 Read Status Register Command
Upon initial device power-up and after exit from reset
mode, the device defaults to read array mode. This
operation is also initiated by writing the Read Array
command. The device remains enabled for reads until
another command is written. Once the internal WSM has
started a block erase, full chip erase, word/byte write or
lock-bit configuration the device will not recognize the
Read Array command until the WSM completes its
operation unless the WSM is suspended via an Erase
Suspend or Word/Byte Write Suspend command. The
Read Array command functions independently of the
VCCW voltage and RP# can be VIH.
The status register may be read to determine when a block
erase, full chip erase, word/byte write or lock-bit
configuration is complete and whether the operation
completed successfully. It may be read at any time by
writing the Read Status Register command. After writing
this command, all subsequent read operations output data
from the status register until another valid command is
written. The status register contents are latched on the
falling edge of OE# or CE#, whichever occurs. OE# or
CE# must toggle to VIH before further reads to update the
status register latch. The Read Status Register command
functions independently of the VCCW voltage. RP# can be
VIH.
4.2 Read Identifier Codes Command
4.4 Clear Status Register Command
The identifier code operation is initiated by writing the
Read Identifier Codes command. Following the command
write, read cycles from addresses shown in Figure 4
retrieve the manufacturer, device, block lock configuration
and permanent lock configuration codes (see Table 4 for
identifier code values). To terminate the operation, write
another valid command. Like the Read Array command,
the Read Identifier Codes command functions
independently of the VCCW voltage and RP# can be VIH.
Following the Read Identifier Codes command, the
following information can be read:
Table 4. Identifier Codes
Address(2)
Data(3)
Code
[A19-A0] [DQ7-DQ0]
Manufacture Code
00000H
B0H
Device Code
00001H
E8H
(1)
Block Lock Configuration
BA +2
DQ0=0
•Block is Unlocked
•Block is Locked
DQ0=1
•Reserved for Future Use
Permanent Lock Configuration
DQ1-7
Status register bits SR.5, SR.4, SR.3 or SR.1 are set to
"1"s by the WSM and can only be reset by the Clear Status
Register command. These bits indicate various failure
conditions (see Table 6). By allowing system software to
reset these bits, several operations (such as cumulatively
erasing multiple blocks or writing several words/bytes in
sequence) may be performed. The status register may be
polled to determine if an error occurred during the
sequence.
To clear the status register, the Clear Status Register
command (50H) is written. It functions independently of
the applied VCCW Voltage. RP# can be VIH. This
command is not functional during block erase or
word/byte write suspend modes.
00003H
•Device is Unlocked
DQ0=0
•Device is Locked
DQ0=1
DQ1-7
•Reserved for Future Use
NOTE:
1. BA selects the specific block lock configuration code
to be read. See Figure 4 for the device identifier code
memory map.
2. A-1 don’t care in byte mode.
3. DQ15-DQ8 outputs 00H in word mode.
Rev. 1.26
LHF16J02
4.5 Block Erase Command
Erase is executed one block at a time and initiated by a
two-cycle command. A block erase setup is first written,
followed by an block erase confirm. This command
sequence requires appropriate sequencing and an address
within the block to be erased (erase changes all block data
to FFFFH/FFH). Block preconditioning, erase, and verify
are handled internally by the WSM (invisible to the
system). After the two-cycle block erase sequence is
written, the device automatically outputs status register
data when read (see Figure 5). The CPU can detect block
erase completion by analyzing the output data of the
RY/BY# pin or status register bit SR.7.
When the block erase is complete, status register bit SR.5
should be checked. If a block erase error is detected, the
status register should be cleared before system software
attempts corrective actions. The CUI remains in read
status register mode until a new command is issued.
This two-step command sequence of set-up followed by
execution ensures that block contents are not accidentally
erased. An invalid Block Erase command sequence will
result in both status register bits SR.4 and SR.5 being set
to "1". Also, reliable block erasure can only occur when
VCC=2.7V-3.6V and VCCW=VCCWH1/2. In the absence of
this high voltage, block contents are protected against
erasure. If block erase is attempted while VCCW≤VCCWLK,
SR.3 and SR.5 will be set to "1". Successful block erase
requires for boot blocks that WP# is VIH and the
corresponding block lock-bit be cleared. In parameter and
main blocks case, it must be cleared the corresponding
block lock-bit. If block erase is attempted when the
excepting above conditions, SR.1 and SR.5 will be set to
"1".
4.6 Full Chip Erase Command
This command followed by a confirm command erases all
of the unlocked blocks. A full chip erase setup (30H) is
first written, followed by a full chip erase confirm (D0H).
After a confirm command is written, device erases the all
unlocked blocks block by block. This command sequence
requires appropriate sequencing. Block preconditioning,
erase and verify are handled internally by the WSM
(invisible to the system). After the two-cycle full chip
erase sequence is written, the device automatically outputs
status register data when read (see Figure 6). The CPU can
detect full chip erase completion by analyzing the output
data of the RY/BY# pin or status register bit SR.7.
When the full chip erase is complete, status register bit
SR.5 should be checked. If erase error is detected, the
status register should be cleared before system software
attempts corrective actions. The CUI remains in read
13
status register mode until a new command is issued. If
error is detected on a block during full chip erase
operation, WSM stops erasing. Full chip erase operation
start from lower address block, finish the higher address
block. Full chip erase can not be suspended.
This two-step command sequence of set-up followed by
execution ensures that block contents are not accidentally
erased. An invalid Full Chip Erase command sequence
will result in both status register bits SR.4 and SR.5 being
set to "1". Also, reliable full chip erasure can only occur
when VCC=2.7V-3.6V and VCCW=VCCWH1/2. In the
absence of this high voltage, block contents are protected
against erasure. If full chip erase is attempted while
VCCW≤VCCWLK, SR.3 and SR.5 will be set to "1".
Successful full chip erase requires for boot blocks that
WP# is VIH and the corresponding block lock-bit be
cleared. In parameter and main blocks case, it must be
cleared the corresponding block lock-bit. If all blocks are
locked, SR.1 and SR.5 will be set to "1".
4.7 Word/Byte Write Command
Word/Byte write is executed by a two-cycle command
sequence. Word/Byte write setup (standard 40H or
alternate 10H) is written, followed by a second write that
specifies the address and data (latched on the rising edge
of WE#). The WSM then takes over, controlling the
word/byte write and write verify algorithms internally.
After the word/byte write sequence is written, the device
automatically outputs status register data when read (see
Figure 7). The CPU can detect the completion of the
word/byte write event by analyzing the RY/BY# pin or
status register bit SR.7.
When word/byte write is complete, status register bit SR.4
should be checked. If word/byte write error is detected, the
status register should be cleared. The internal WSM verify
only detects errors for "1"s that do not successfully write
to "0"s. The CUI remains in read status register mode until
it receives another command.
Reliable word/byte writes can only occur when
VCC=2.7V-3.6V and VCCW=VCCWH1/2. In the absence of
this high voltage, memory contents are protected against
word/byte writes. If word/byte write is attempted while
VCCW≤VCCWLK, status register bits SR.3 and SR.4 will be
set to "1". Successful word/byte write requires for boot
blocks that WP# is VIH and the corresponding block lockbit be cleared. In parameter and main blocks case, it must
be cleared the corresponding block lock-bit. If word/byte
write is attempted when the excepting above conditions,
SR.1 and SR.4 will be set to "1".
Rev. 1.26
LHF16J02
14
4.8 Block Erase Suspend Command
4.9 Word/Byte Write Suspend Command
The Block Erase Suspend command allows block-erase
interruption to read or word/byte write data in another
block of memory. Once the block erase process starts,
writing the Block Erase Suspend command requests that
the WSM suspend the block erase sequence at a
predetermined point in the algorithm. The device outputs
status register data when read after the Block Erase
Suspend command is written. Polling status register bits
SR.7 and SR.6 can determine when the block erase
operation has been suspended (both will be set to "1").
RY/BY# will also transition to High Z. Specification
tWHRZ2 defines the block erase suspend latency.
The Word/Byte Write Suspend command allows
word/byte write interruption to read data in other flash
memory locations. Once the word/byte write process
starts, writing the Word/Byte Write Suspend command
requests that the WSM suspend the Word/Byte write
sequence at a predetermined point in the algorithm. The
device continues to output status register data when read
after the Word/Byte Write Suspend command is written.
Polling status register bits SR.7 and SR.2 can determine
when the word/byte write operation has been suspended
(both will be set to "1"). RY/BY# will also transition to
High Z. Specification tWHRZ1 defines the word/byte write
suspend latency.
When Block Erase Suspend command write to the CUI, if
block erase was finished, the device places read array
mode. Therefore, after Block Erase Suspend command
write to the CUI, Read Status Register command (70H)
has to write to CUI, then status register bit SR.6 should be
checked for places the device in suspend mode.
At this point, a Read Array command can be written to
read data from blocks other than that which is suspended.
A Word/Byte Write command sequence can also be issued
during erase suspend to program data in other blocks.
Using the Word/Byte Write Suspend command (see
Section 4.9), a word/byte write operation can also be
suspended. During a word/byte write operation with block
erase suspended, status register bit SR.7 will return to "0"
and the RY/BY# output will transition to VOL. However,
SR.6 will remain "1" to indicate block erase suspend
status.
The only other valid commands while block erase is
suspended are Read Status Register and Block Erase
Resume. After a Block Erase Resume command is written
to the flash memory, the WSM will continue the block
erase process. Status register bits SR.6 and SR.7 will
automatically clear and RY/BY# will return to VOL. After
the Erase Resume command is written, the device
automatically outputs status register data when read (see
Figure 8). VCCW must remain at VCCWH1/2 (the same
VCCW level used for block erase) while block erase is
suspended. RP# must also remain at VIH. WP# must also
remain at VIL or VIH (the same WP# level used for block
erase). Block erase cannot resume until word/byte write
operations initiated during block erase suspend have
completed.
When Word/Byte Write Suspend command write to the
CUI, if word/byte write was finished, the device places
read array mode. Therefore, after Word/Byte Write
Suspend command write to the CUI, Read Status Register
command (70H) has to write to CUI, then status register
bit SR.2 should be checked for places the device in
suspend mode.
At this point, a Read Array command can be written to
read data from locations other than that which is
suspended. The only other valid commands while
word/byte write is suspended are Read Status Register and
Word/Byte Write Resume. After Word/Byte Write
Resume command is written to the flash memory, the
WSM will continue the word/byte write process. Status
register bits SR.2 and SR.7 will automatically clear and
RY/BY# will return to VOL. After the Word/Byte Write
Resume command is written, the device automatically
outputs status register data when read (see Figure 9).
VCCW must remain at VCCWH1/2 (the same VCCW level
used for word/byte write) while in word/byte write
suspend mode. RP# must also remain at VIH. WP# must
also remain at VIL or VIH (the same WP# level used for
word/byte write).
If the period of from Word/Byte Write Resume command
write to the CUI till Word/Byte Write Suspend command
write to the CUI be short and done again and again, write
time be prolonged.
If the period of from Block Erase Resume command write
to the CUI till Block Erase Suspend command write to the
CUI be short and done again and again, erase time be
prolonged.
Rev. 1.26
LHF16J02
4.10 Set Block and Permanent Lock-Bit
Commands
A flexible block locking and unlocking scheme is enabled
via a combination of block lock-bits, a permanent lock-bit
and WP# pin. The block lock-bits and WP# pin gates
program and erase operations while the permanent lock-bit
gates block-lock bit modification. With the permanent
lock-bit not set, individual block lock-bits can be set using
the Set Block Lock-Bit command. The Set Permanent
Lock-Bit command, sets the permanent lock-bit. After the
permanent lock-bit is set, block lock-bits and locked block
contents cannot altered. See Table 5 for a summary of
hardware and software write protection options.
Set block lock-bit and permanent lock-bit are executed by
a two-cycle command sequence. The set block or
permanent lock-bit setup along with appropriate block or
device address is written followed by either the set block
lock-bit confirm (and an address within the block to be
locked) or the set permanent lock-bit confirm (and any
device address). The WSM then controls the set lock-bit
algorithm. After the sequence is written, the device
automatically outputs status register data when read (see
Figure 10). The CPU can detect the completion of the set
lock-bit event by analyzing the RY/BY# pin output or
status register bit SR.7.
When the set lock-bit operation is complete, status register
bit SR.4 should be checked. If an error is detected, the
status register should be cleared. The CUI will remain in
read status register mode until a new command is issued.
This two-step sequence of set-up followed by execution
ensures that lock-bits are not accidentally set. An invalid
Set Block or Permanent Lock-Bit command will result in
status register bits SR.4 and SR.5 being set to "1". Also,
reliable operations occur only when VCC=2.7V-3.6V and
VCCW=VCCWH1/2. In the absence of this high voltage,
lock-bit contents are protected against alteration.
A successful set block lock-bit operation requires that the
permanent lock-bit be cleared. If it is attempted with the
permanent lock-bit set, SR.1 and SR.4 will be set to "1"
and the operation will fail.
15
4.11 Clear Block Lock-Bits Command
All set block lock-bits are cleared in parallel via the Clear
Block Lock-Bits command. With the permanent lock-bit
not set, block lock-bits can be cleared using only the Clear
Block Lock-Bits command. If the permanent lock-bit is
set, block lock-bits cannot cleared. See Table 5 for a
summary of hardware and software write protection
options.
Clear block lock-bits operation is executed by a two-cycle
command sequence. A clear block lock-bits setup is first
written. After the command is written, the device
automatically outputs status register data when read (see
Figure 11). The CPU can detect completion of the clear
block lock-bits event by analyzing the RY/BY# Pin output
or status register bit SR.7.
When the operation is complete, status register bit SR.5
should be checked. If a clear block lock-bit error is
detected, the status register should be cleared. The CUI
will remain in read status register mode until another
command is issued.
This two-step sequence of set-up followed by execution
ensures that block lock-bits are not accidentally cleared.
An invalid Clear Block Lock-Bits command sequence will
result in status register bits SR.4 and SR.5 being set to "1".
Also, a reliable clear block lock-bits operation can only
occur when VCC=2.7V-3.6V and VCCW=VCCWH1/2. If a
clear block lock-bits operation is attempted while
VCCW≤VCCWLK, SR.3 and SR.5 will be set to "1". In the
absence of this high voltage, the block lock-bits content
are protected against alteration. A successful clear block
lock-bits operation requires that the permanent lock-bit is
not set. If it is attempted with the permanent lock-bit set,
SR.1 and SR.5 will be set to "1" and the operation will
fail.
If a clear block lock-bits operation is aborted due to VCCW
or VCC transitioning out of valid range or RP# active
transition, block lock-bit values are left in an
undetermined state. A repeat of clear block lock-bits is
required to initialize block lock-bit contents to known
values. Once the permanent lock-bit is set, it cannot be
cleared.
Rev. 1.26
LHF16J02
4.12 Block Locking by the WP#
This Boot Block Flash memory architecture features two
hardware-lockable boot blocks so that the kernel code for
the system can be kept secure while other blocks are
programmed or erased as necessary.
16
result in an error, which will be reflected in the status
register. For top configuration, the top two boot blocks are
lockable. For the bottom configuration, the bottom two
boot blocks are lockable. If WP# is VIH and block lockbit is not set, boot block can be programmed or erased
normally (Unless VCCW is below VCCWLK). WP# is valid
only two boot blocks, other blocks are not affected.
The lockable two boot blocks are locked when WP#=VIL;
any program or erase operation to a locked block will
Operation
VCCW
RP#
Block Erase ≤VCCWLK
or
>VCCWLK
Word/Byte
Write
X
VIL
VIH
Full Chip
Erase
≤VCCWLK
>VCCWLK
X
VIL
VIH
Set Block
Lock-Bit
≤VCCWLK
>VCCWLK
X
VIL
VIH
Clear Block ≤VCCWLK
Lock-Bits >VCCWLK
X
VIL
VIH
≤VCCWLK
>VCCWLK
X
VIL
VIH
Set
Permanent
Lock-Bit
Table 5. Write Protection Alternatives
Permanent Block
WP#
Effect
Lock-Bit Lock-bit
X
X
X All Blocks Locked.
X
X
X All Blocks Locked.
X
0
VIL 2 Boot Blocks Locked.
VIH Block Erase and Word/Byte Write Enabled.
1
VIL Block Erase and Word/Byte Write Disabled.
VIH Block Erase and Word/Byte Write Disabled.
X
X
X All Blocks Locked.
X
X
X All Blocks Locked.
X
X
VIL All Unlocked Blocks are Erased.
2 Boot Blocks and Locked Blocks are NOT Erased.
VIH All Unlocked Blocks are Erased,
Locked Blocks are NOT Erased.
X
X
X Set Block Lock-Bit Disabled.
X
X
X Set Block Lock-Bit Disabled.
0
X
X Set Block Lock-Bit Enabled.
1
X
X Set Block Lock-Bit Disabled.
X
X
X Clear Block Lock-Bits Disabled.
X
X
X Clear Block Lock-Bits Disabled.
0
X
X Clear Block Lock-Bits Enabled.
1
X
X Clear Block Lock-Bits Disabled.
X
X
X Set Permanent Lock-Bit Disabled.
X
X
X Set Permanent Lock-Bit Disabled.
X
X
X Set Permanent Lock-Bit Enabled.
Rev. 1.26
LHF16J02
WSMS
BESS
ECBLBS
7
6
5
17
Table 6. Status Register Definition
WBWSLBS
VCCWS
WBWSS
4
3
2
DPS
R
1
0
NOTES:
SR.7 = WRITE STATE MACHINE STATUS (WSMS)
1 = Ready
0 = Busy
Check RY/BY# or SR.7 to determine block erase, full chip
erase, word/byte write or lock-bit configuration completion.
SR.6-0 are invalid while SR.7="0".
SR.6 = BLOCK ERASE SUSPEND STATUS (BESS)
1 = Block Erase Suspended
0 = Block Erase in Progress/Completed
SR.5 = ERASE AND CLEAR BLOCK LOCK-BITS
STATUS (ECBLBS)
1 = Error in Block Erase, Full Chip Erase or Clear Block
Lock-Bits
0 = Successful Block Erase, Full Chip Erase or Clear
Block Lock-Bits
SR.4 = WORD/BYTE WRITE AND SET LOCK-BIT
STATUS (WBWSLBS)
1 = Error in Word/Byte Write or Set Block/Permanent
Lock-Bit
0 = Successful Word/Byte Write or Set Block/Permanent
Lock-Bit
SR.3 = VCCW STATUS (VCCWS)
1 = VCCW Low Detect, Operation Abort
0 = VCCW OK
SR.2 = WORD/BYTE WRITE SUSPEND STATUS
(WBWSS)
1 = Word/Byte Write Suspended
0 = Word/Byte Write in Progress/Completed
SR.1 = DEVICE PROTECT STATUS (DPS)
1 = Block Lock-Bit, Permanent Lock-Bit and/or WP#
Lock Detected, Operation Abort
0 = Unlock
SR.0 = RESERVED FOR FUTURE ENHANCEMENTS (R)
If both SR.5 and SR.4 are "1"s after a block erase, full chip
erase or lock-bit configuration attempt, an improper
command sequence was entered.
SR.3 does not provide a continuous indication of VCCW
level. The WSM interrogates and indicates the VCCW level
only after Block Erase, Full Chip Erase, Word/Byte Write or
Lock-Bit Configuration command sequences. SR.3 is not
guaranteed to reports accurate feedback only when
VCCW≠VCCWH1/2.
SR.1 does not provide a continuous indication of permanent
and block lock-bit and WP# values. The WSM interrogates
the permanent lock-bit, block lock-bit and WP# only after
Block Erase, Full Chip Erase, Word/Byte Write or Lock-Bit
Configuration command sequences. It informs the system,
depending on the attempted operation, if the block lock-bit is
set, permanent lock-bit is set and/or WP# is VIL. Reading
the block lock and permanent lock configuration codes after
writing the Read Identifier Codes command indicates
permanent and block lock-bit status.
SR.0 is reserved for future use and should be masked out
when polling the status register.
Rev. 1.26
LHF16J02
18
Start
Bus
Operation
Command
Write 70H
Write
Read Status
Register
Read Status
Register
Read
Comments
Data=70H
Addr=X
Status Register Data
Check SR.7
Standby
SR.7=
1=WSM Ready
0
0=WSM Busy
1
Write 20H
Write D0H,
Block Address
Write
Erase Setup
Write
Erase
Confirm
Addr=X
Data=D0H
Addr=Within Block to be Erased
Status Register Data
Read
Read Status
Register
Check SR.7
Suspend Block
Erase Loop
No
SR.7=
Data=20H
0
Suspend
Block Erase
1=WSM Ready
Standby
0=WSM Busy
Repeat for subsequent block erasures.
Yes
Full status check can be done after each block erase or after a sequence of
block erasures.
1
Write FFH after the last operation to place device in read array mode.
Full Status
Check if Desired
Block Erase
Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data(See Above)
SR.3=
Bus
Operation
1
Standby
SR.1=
Standby
1
Device Protect Error
0
Check SR.3
1=VCCW Error Detect
VCCW Range Error
0
Comments
Command
Standby
Standby
Check SR.1
1=Device Protect Detect
Check SR.4,5
Both 1=Command Sequence Error
Check SR.5
1=Block Erase Error
SR.4,5=
1
Command Sequence
Error
where multiple blocks are erased before full status is checked.
If error is detected, clear the Status Register before attempting retry or other error recovery.
0
SR.5=
SR.5, SR.4, SR.3 and SR.1 are only cleared by the Clear Status Register Command in cases
1
Block Erase Error
0
Block Erase Successful
Figure 5. Automated Block Erase Flowchart
Rev. 1.26
LHF16J02
Start
Write 70H
Read Status
Register
19
Bus
Operation
Command
Write
Read Status
Register
Comments
Data=70H
Addr=X
Status Register Data
Read
Check SR.7
SR.7=
Standby
0
1=WSM Ready
0=WSM Busy
1
Write
Full Chip Erase
Setup
Data=30H
Write
Full Chip Erase
Confirm
Data=D0H
Write 30H
Write D0H
Addr=X
Addr=X
Status Register Data
Read
Check SR.7
Read Status
Register
Standby
1=WSM Ready
0=WSM Busy
SR.7=
Full status check can be done after each full chip erase.
0
Write FFH after the last operation to place device in read array mode.
1
Full Status
Check if Desired
Full Chip Erase
Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data(See Above)
SR.3=
Bus
Operation
1
Comments
Command
Standby
VCCW Range Error
Check SR.3
1=VCCW Error Detect
Check SR.1
0
Standby
1=Device Protect Detect
(All Blocks are locked)
SR.1=
1
Device Protect Error
Standby
Check SR.4,5
Both 1=Command Sequence Error
0
Standby
SR.4,5=
1
Command Sequence
Error
Check SR.5
1=Full Chip Erase Error
SR.5, SR.4, SR.3 and SR.1 are only cleared by the Clear Status Register Command in cases
where multiple blocks are erased before full status is checked.
0
If error is detected, clear the Status Register before attempting retry or other error recovery.
SR.5=
1
Full Chip Erase Error
0
Full Chip Erase
Successful
Figure 6. Automated Full Chip Erase Flowchart
Rev. 1.26
LHF16J02
20
Start
Bus
Operation
Command
Write 70H
Write
Read Status
Register
Read Status
Register
Read
Comments
Data=70H
Addr=X
Status Register Data
Check SR.7
Standby
SR.7=
1=WSM Ready
0
0=WSM Busy
1
Write 40H or 10H
Write Word/Byte
Data and Address
Write
Setup Word/Byte Write
Write
Word/Byte Write
Read
Addr=X
Data=Data to Be Written
Addr=Location to Be Written
Status Register Data
Read
Status Register
Check SR.7
No
SR.7=
Data=40H or 10H
0
Suspend
Word/Byte
Write
Suspend Word/Byte
Write Loop
1=WSM Ready
Standby
0=WSM Busy
Repeat for subsequent word/byte writes.
Yes
SR full status check can be done after each word/byte write, or after a sequence of
word/byte writes.
1
Write FFH after the last word/byte write operation to place device in read array mode.
Full Status
Check if Desired
Word/Byte Write
Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data(See Above)
SR.3=
Bus
Operation
1
Standby
VCCW Range Error
Standby
0
SR.1=
1
Device Protect Error
Comments
Command
Standby
Check SR.3
1=VCCW Error Detect
Check SR.1
1=Device Protect Detect
Check SR.4
1=Data Write Error
SR.4, SR.3 and SR.1 are only cleared by the Clear Status Register command in cases
0
where multiple locations are written before full status is checked.
If error is detected, clear the Status Register before attempting retry or other error recovery.
SR.4=
1
Word/Byte Write Error
0
Word/Byte Write Successful
Figure 7. Automated Word/Byte Write Flowchart
Rev. 1.26
LHF16J02
Start
Write B0H
21
Bus
Operation
Command
Write
Erase
Suspend
Comments
Data=B0H
Addr=X
Status Register Data
Read
Addr=X
Read
Status Register
Check SR.7
1=WSM Ready
Standby
0=WSM Busy
0
SR.7=
Check SR.6
Standby
1=Block Erase Suspended
0=Block Erase Completed
1
Write
0
SR.6=
Erase
Resume
Data=D0H
Addr=X
Block Erase Completed
1
Read or
Word/Byte
Write ?
Read
Read Array Data
Word/Byte Write
Word/Byte Write Loop
No
Done?
Yes
Write D0H
Write FFH
Block Erase Resumed
Read Array Data
Figure 8. Block Erase Suspend/Resume Flowchart
Rev. 1.26
LHF16J02
Start
Write B0H
22
Bus
Operation
Command
Write
Word/Byte Write
Suspend
Comments
Data=B0H
Addr=X
Status Register Data
Read
Addr=X
Read
Status Register
Check SR.7
Standby
1=WSM Ready
0=WSM Busy
SR.7=
0
Check SR.2
Standby
1=Word/Byte Write Suspended
0=Word/Byte Write Completed
1
Write
SR.2=
0
Read Array
Data=FFH
Addr=X
Word/Byte Write Completed
Read Array locations other
Read
than that being written.
1
Write
Write FFH
Word/Byte Write
Resume
Data=D0H
Addr=X
Read Array Data
Done
Reading
No
Yes
Write D0H
Write FFH
Word/Byte Write Resumed
Read Array Data
Figure 9. Word/Byte Write Suspend/Resume Flowchart
Rev. 1.26
LHF16J02
23
Start
Bus
Operation
Command
Write 70H
Write
Read Status
Register
Read Status
Register
Read
Comments
Data=70H
Addr=X
Status Register Data
Check SR.7
Standby
SR.7=
1=WSM Ready
0
0=WSM Busy
1
Write
Set
Block/Permanent
Lock-Bit Setup
Write
Set
Block or Permanent
Lock-Bit Confirm
Data=60H
Addr=X
Write 60H
Data=01H(Block),
Write 01H/F1H,
Block/Device Address
F1H(Permanent)
Addr=Block Address(Block),
Device Address(Permanent)
Read
Status Register
Status Register Data
Read
Check SR.7
SR.7=
Standby
0
1=WSM Ready
0=WSM Busy
1
Repeat for subsequent lock-bit set operations.
Full status check can be done after each lock-bit set operation or after a sequence of
Full Status
Check if Desired
lock-bit set operations.
Write FFH after the last lock-bit set operation to place device in read array mode.
Set Lock-Bit
Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data(See Above)
SR.3=
Bus
Operation
1
Standby
VCCW Range Error
Command
Comments
Check SR.3
1=VCCW Error Detect
Check SR.1
0
Standby
SR.1=
1
(Set Block Lock-Bit Operation)
Standby
1
Permanent Lock-Bit is Set
Device Protect Error
0
SR.4,5=
1=Device Protect Detect
Command Sequence
Error
0
Standby
Check SR.4,5
Both 1=Command Sequence Error
Check SR.4
1=Set Lock-Bit Error
SR.5, SR.4, SR.3 and SR.1 are only cleared by the Clear Status Register command in cases
where multiple lock-bits are set before full status is checked.
SR.4=
1
If error is detected, clear the Status Register before attempting retry or other error recovery.
Set Lock-Bit Error
0
Set Lock-Bit Successful
Figure 10. Set Block and Permanent Lock-Bit Flowchart
Rev. 1.26
LHF16J02
24
Start
Bus
Operation
Command
Write 70H
Write
Read Status
Register
Read Status
Register
Read
Comments
Data=70H
Addr=X
Status Register Data
Check SR.7
Standby
SR.7=
1=WSM Ready
0
0=WSM Busy
1
Write 60H
Write D0H
Write
Clear Block
Lock-Bits Setup
Data=60H
Write
Clear Block
Lock-Bits Confirm
Data=D0H
Addr=X
Status Register Data
Read
Read
Status Register
Addr=X
Check SR.7
Standby
1=WSM Ready
0=WSM Busy
SR.7=
0
Write FFH after the Clear Block Lock-Bits operation to place device in read array mode.
1
Full Status
Check if Desired
Clear Block Lock-Bits
Complete
FULL STATUS CHECK PROCEDURE
Read Status Register
Data(See Above)
Bus
Operation
1
SR.3=
Comments
Command
Standby
VCCW Range Error
Check SR.3
1=VCCW Error Detect
Check SR.1
0
Standby
1=Device Protect Detect
Permanent Lock-Bit is Set
SR.1=
1
Device Protect Error
Standby
Check SR.4,5
Both 1=Command Sequence Error
0
SR.4,5=
1
Standby
Command Sequence
Error
1=Clear Block Lock-Bits Error
SR.5, SR.4, SR.3 and SR.1 are only cleared by the Clear Status Register command.
0
SR.5=
Check SR.5
If error is detected, clear the Status Register before attempting retry or other error recovery.
1
Clear Block Lock-Bits
Error
0
Clear Block Lock-Bits
Successful
Figure 11. Clear Block Lock-Bits Flowchart
Rev. 1.26
LHF16J02
25
5 DESIGN CONSIDERATIONS
5.3 Power Supply Decoupling
5.1 Three-Line Output Control
Flash memory power switching characteristics require
careful device decoupling. System designers are interested
in three supply current issues; standby current levels,
active current levels and transient peaks produced by
falling and rising edges of CE# and OE#. Transient current
magnitudes depend on the device outputs’ capacitive and
inductive loading. Two-line control and proper decoupling
capacitor selection will suppress transient voltage peaks.
Each device should have a 0.1µF ceramic capacitor
connected between its VCC and GND and between its
VCCW and GND. These high-frequency, low inductance
capacitors should be placed as close as possible to package
leads. Additionally, for every eight devices, a 4.7µF
electrolytic capacitor should be placed at the array’s power
supply connection between VCC and GND. The bulk
capacitor will overcome voltage slumps caused by PC
board trace inductance.
The device will often be used in large memory arrays.
SHARP provides three control inputs to accommodate
multiple memory connections. Three-line control provides
for:
a. Lowest possible memory power dissipation.
b. Complete assurance that data bus contention will not
occur.
To use these control inputs efficiently, an address decoder
should enable CE# while OE# should be connected to all
memory devices and the system’s READ# control line.
This assures that only selected memory devices have
active outputs while deselected memory devices are in
standby mode. RP# should be connected to the system
POWERGOOD signal to prevent unintended writes during
system power transitions. POWERGOOD should also
toggle during system reset.
5.2 RY/BY# and WSM Polling
RY/BY# is an open drain output that should be connected
to VCC by a pull up resistor to provides a hardware method
of detecting block erase, full chip erase, word/byte write
and lock-bit configuration completion. It transitions low
after block erase, full chip erase, word/byte write or lockbit configuration commands and returns to VOH (while
RY/BY# is pull up) when the WSM has finished executing
the internal algorithm.
RY/BY# can be connected to an interrupt input of the
system CPU or controller. It is active at all times. RY/BY#
is also High Z when the device is in block erase suspend
(with word/byte write inactive), word/byte write suspend
or reset modes.
5.4 VCCW Trace on Printed Circuit Boards
Updating flash memories that reside in the target system
requires that the printed circuit board designer pay
attention to the VCCW Power supply trace. The VCCW pin
supplies the memory cell current for word/byte writing
and block erasing. Use similar trace widths and layout
considerations given to the VCC power bus. Adequate
VCCW supply traces and decoupling will decrease VCCW
voltage spikes and overshoots.
5.5 VCC, VCCW, RP# Transitions
Block erase, full chip erase, word/byte write and lock-bit
configuration are not guaranteed if VCCW falls outside of a
valid VCCWH1/2 range, VCC falls outside of a valid 2.7V3.6V range, or RP#≠VIH. If VCCW error is detected, status
register bit SR.3 is set to "1" along with SR.4 or SR.5,
depending on the attempted operation. If RP# transitions
to VIL during block erase, full chip erase, word/byte write
or lock-bit configuration, RY/BY# will remain low until
the reset operation is complete. Then, the operation will
abort and the device will enter reset mode. The aborted
operation may leave data partially altered. Therefore, the
command sequence must be repeated after normal
operation is restored. Device power-off or RP# transitions
to VIL clear the status register.
The CUI latches commands issued by system software and
is not altered by VCCW or CE# transitions or WSM
actions. Its state is read array mode upon power-up, after
exit from reset mode or after VCC transitions below VLKO.
Rev. 1.26
LHF16J02
26
5.6 Power-Up/Down Protection
5.8 Data Protection Method
The device is designed to offer protection against
accidental block erase, full chip erase, word/byte write or
lock-bit configuration during power transitions. Upon
power-up, the device is indifferent as to which power
supply (VCCW or VCC) powers-up first. Internal circuitry
resets the CUI to read array mode at power-up.
Noises having a level exceeding the limit specified in the
specification may be generated under specific operating
conditions on some systems. Such noises, when induced
onto WE# signal or power supply, may be interpreted as
false commands, causing undesired memory updating. To
protect the data stored in the flash memory against
unwanted overwriting, systems operating with the flash
memory should have the following write protect designs,
as appropriate:
A system designer must guard against spurious writes for
VCC voltages above VLKO when VCCW is active. Since
both WE# and CE# must be low for a command write,
driving either to VIH will inhibit writes. The CUI’s twostep command sequence architecture provides added level
of protection against data alteration.
In-system block lock and unlock capability prevents
inadvertent data alteration. The device is disabled while
RP#=VIL regardless of its control inputs state.
5.7 Power Dissipation
When designing portable systems, designers must consider
battery power consumption not only during device
operation, but also for data retention during system idle
time. Flash memory’s nonvolatility increases usable
battery life because data is retained when system power is
removed.
1) Protecting data in specific block
When a lock bit is set, the corresponding block (includes
the 2 boot blocks) is protected against overwriting. By
setting a WP# to low, only the 2 boot blocks can be
protected against overwriting. By using this feature, the
flash memory space can be divided into the program
section (locked section) and data section (unlocked
section). The permanent lock bit can be used to prevent
false block bit setting. For further information on
setting/resetting lock-bit, refer to the specification. (See
chapter 4.10 and 4.11.)
2) Data protection through VCCW
When the level of VCCW is lower than VCCWLK (lockout
voltage), write operation on the flash memory is disabled.
All blocks are locked and the data in the blocks are
completely write protected. For the lockout voltage, refer
to the specification. (See chapter 6.2.3.)
3) Data protection through RP#
When the RP# is kept low during read mode, the flash
memory will be reset mode, then write protecting all
blocks. When the RP# is kept low during power up and
power down sequence such as voltage transition, write
operation on the flash memory is disabled, write
protecting all blocks. For the details of RP# control, refer
to the specification. (See chapter 5.6 and 6.2.7.)
Rev. 1.26
LHF16J02
6 ELECTRICAL SPECIFICATIONS
6.1 Absolute Maximum Ratings*
Operating Temperature
During Read, Block Erase,
Full Chip Erase, Word/Byte Write
and Lock-Bit Configuration ................0°C to +70°C(1)
Storage Temperature
During under Bias ............................... -10°C to +80°C
During non Bias ................................ -65°C to +125°C
Voltage On Any Pin
(except VCC and VCCW) ........... -0.5V to VCC+0.5V(2)
VCC Supply Voltage................................ -0.2V to +4.6V(2)
VCCW Supply Voltage......................... -0.2V to +13.0V(2,3)
Output Short Circuit Current................................100mA(4)
27
*WARNING: Stressing the device beyond the "Absolute
Maximum Ratings" may cause permanent damage. These
are stress ratings only. Operation beyond the "Operating
Conditions" is not recommended and extended exposure
beyond the "Operating Conditions" may affect device
reliability.
NOTES:
1. Operating temperature is for commercial temperature
product defined by this specification.
2. All specified voltages are with respect to GND.
Minimum DC voltage is -0.5V on input/output pins
and -0.2V on VCC and VCCW pins. During transitions,
this level may undershoot to -2.0V for periods <20ns.
Maximum DC voltage on input/output pins are
VCC+0.5V which, during transitions, may overshoot to
VCC+2.0V for periods <20ns.
3. Maximum DC voltage on VCCW may overshoot to
+13.0V for periods <20ns. Applying 12V±0.3V to
VCCW during erase/write can only be done for a
maximum of 1000 cycles on each block. VCCW may be
connected to 12V±0.3V for a total of 80 hours
maximum.
4. Output shorted for no more than one second. No more
than one output shorted at a time.
6.2 Operating Conditions
Temperature and VCC Operating Conditions
Symbol
Parameter
Min.
Max.
Unit
TA
Operating Temperature
0
+70
°C
VCC
VCC Supply Voltage (2.7V-3.6V)
2.7
3.6
V
Test Condition
Ambient Temperature
6.2.1 CAPACITANCE(1)
Symbol
Parameter
Input Capacitance
Output Capacitance
CIN
COUT
NOTE:
1. Sampled, not 100% tested.
TA=+25°C, f=1MHz
Typ.
Max.
7
10
9
12
Unit
pF
pF
Condition
VIN=0.0V
VOUT=0.0V
Rev. 1.26
LHF16J02
28
6.2.2 AC INPUT/OUTPUT TEST CONDITIONS
2.7
1.35
INPUT
TEST POINTS
1.35
OUTPUT
0.0
AC test inputs are driven at 2.7V for a Logic "1" and 0.0V for a Logic "0". Input timing begins, and output timing ends, at 1.35V.
Input rise and fall times (10% to 90%) <10 ns.
Figure 12. Transient Input/Output Reference Waveform for VCC=2.7V-3.6V
Test Configuration Capacitance Loading Value
Test Configuration
CL(pF)
VCC=2.7V-3.6V
50
1.3V
1N914
RL=3.3kΩ
DEVICE
UNDER
TEST
CL Includes Jig
Capacitance
OUT
CL
Figure 13. Transient Equivalent Testing Load Circuit
Rev. 1.26
LHF16J02
29
6.2.3 DC CHARACTERISTICS
Sym.
ILI
Parameter
Input Load Current
ILO
Output Leakage Current
ICCS
VCC Standby Current
ICCAS
VCC Auto Power-Save Current
ICCD
VCC Reset Power-Down Current
ICCR
VCC Read Current
ICCW
ICCWS
ICCES
ICCWS
VCC Word/Byte Write or Set LockBit Current
VCC Block Erase, Full Chip Erase or
Clear Block Lock-Bits Current
VCC Word/Byte Write or
Block Erase Suspend Current
VCCW Standby or Read Current
ICCWR
ICCWAS
VCCW Auto Power-Save Current
ICCE
ICCWD
ICCWW
ICCWE
ICCWWS
ICCWES
VCCW Reset Power-Down Current
VCCW Word/Byte Write or Set LockBit Current
VCCW Block Erase, Full Chip Erase
or Clear Block Lock-Bits Current
VCCW Word/Byte Write or
Block Erase Suspend Current
DC Characteristics
VCC=2.7V-3.6V
Notes
Typ.
Max.
1
±0.5
±0.5
µA
2
15
µA
0.2
2
mA
2
15
µA
2
15
µA
15
25
mA
30
mA
5
5
4
4
17
12
17
12
mA
mA
mA
mA
Test
Conditions
VCC=VCCMax.
VIN=VCC or GND
VCC=VCCMax.
VOUT=VCC or GND
CMOS Level Inputs
VCC=VCCMax.
CE#=RP#=VCC±0.2V
TTL Level Inputs
VCC=VCCMax.
CE#=RP#=VIH
CMOS Level Inputs
VCC=VCCMax.
CE#=GND±0.2V
RP#=GND±0.2V
IOUT(RY/BY#)=0mA
CMOS Level Inputs
VCC=VCCMax., CE#=GND
f=5MHz, IOUT=0mA
TTL Level Inputs
VCC=VCCMax., CE#=GND
f=5MHz, IOUT=0mA
VCCW=2.7V-3.6V
VCCW=11.7V-12.3V
VCCW=2.7V-3.6V
VCCW=11.7V-12.3V
1
6
mA
CE#=VIH
±2
10
±15
200
µA
µA
0.1
5
µA
1
1,7
0.1
12
1,7
8
5
40
30
25
20
µA
mA
mA
mA
mA
VCCW≤VCC
VCCW>VCC
CMOS Level Inputs
VCC=VCCMax.
CE#=GND±0.2V
RP#=GND±0.2V
VCCW=2.7V-3.6V
VCCW=11.7V-12.3V
VCCW=2.7V-3.6V
VCCW=11.7V-12.3V
200
µA
VCCW=VCCWH1/2
1
Unit
µA
1,3,6
1,5,6
1
1,6
1,7
1,7
1,2
1
1,5,6
1
10
Rev. 1.26
LHF16J02
Sym.
VIL
VIH
Parameter
Input Low Voltage
Input High Voltage
VOL
Output Low Voltage
VOH1
Output High Voltage
(TTL)
Output High Voltage
(CMOS)
VOH2
DC Characteristics (Continued)
VCC=2.7V-3.6V
Notes
Min.
Max.
7
-0.5
0.8
7
VCC
2.0
+0.5
3,7
0.4
7
7
2.4
0.85
VCC
VCC
-0.4
30
Unit
V
Test Conditions
V
V
V
V
V
VCC=VCC Min.
IOL=2.0mA
VCC=VCC Min.
IOH=-2.0mA
VCC=VCC Min.
IOH=-2.5mA
VCC=VCC Min.
IOH=-100µA
VCCWLK VCCW Lockout during Normal
4,7
1.0
V
Operations
VCCWH1 VCCW during Block Erase, Full Chip
Erase, Word/Byte Write or Lock-Bit
2.7
3.6
V
Configuration Operations
VCCWH2 VCCW during Block Erase, Full Chip
8
Erase, Word/Byte Write or Lock-Bit
11.7
12.3
V
Configuration Operations
VLKO
VCC Lockout Voltage
2.0
V
NOTES:
1. All currents are in RMS unless otherwise noted. Typical values at nominal VCC voltage and TA=+25°C.
2. ICCWS and ICCES are specified with the device de-selected. If read or word/byte written while in erase suspend mode, the
device’s current draw is the sum of ICCWS or ICCES and ICCR or ICCW, respectively.
3. Includes RY/BY#.
4. Block erases, full chip erase, word/byte writes and lock-bit configurations are inhibited when VCCW≤VCCWLK, and not
guaranteed in the range between VCCWLK(max.) and VCCWH1(min.), between VCCWH1(max.) and VCCWH2(min.) and
above VCCWH2(max.).
5. The Automatic Power Savings (APS) feature is placed automatically power save mode that addresses not switching more
than 300ns while read mode.
6. About all of pin except describe Test Conditions, CMOS level inputs are either VCC±0.2V or GND±0.2V, TTL level
inputs are either VIL or VIH.
7. Sampled, not 100% tested.
8. Applying 12V±0.3V to VCCW during erase/write can only be done for a maximum of 1000 cycles on each block. VCCW
may be connected to 12V±0.3V for a total of 80 hours maximum.
Rev. 1.26
LHF16J02
31
6.2.4 AC CHARACTERISTICS - READ-ONLY OPERATIONS(1)
Sym.
tAVAV
tAVQV
tELQV
tPHQV
tGLQV
tELQX
tEHQZ
tGLQX
tGHQZ
tOH
VCC=2.7V-3.6V, TA=0°C to +70°C
Parameter
Notes
Read Cycle Time
Address to Output Delay
CE# to Output Delay
RP# High to Output Delay
OE# to Output Delay
CE# to Output in Low Z
CE# High to Output in High Z
OE# to Output in Low Z
OE# High to Output in High Z
Output Hold from Address, CE# or OE# Change, Whichever
Occurs First
BYTE# to Output Delay
BYTE# Low to Output in High Z
CE# to BYTE# High or Low
Min.
90
90
90
600
40
2
2
3
3
3
3
3
Max.
0
40
0
15
0
tFVQV
3
tFLQZ
3
tELFV
3,4
NOTES:
1. See AC Input/Output Reference Waveform for maximum allowable input slew rate.
2. OE# may be delayed up to tELQV-tGLQV after the falling edge of CE# without impact on tELQV.
3. Sampled, not 100% tested.
4. If BYTE# transfer during reading cycle, exist the regulations separately.
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
90
25
5
ns
ns
ns
Rev. 1.26
LHF16J02
VIH
Standby
Device
Address Selection
32
Data Valid
Address Stable
ADDRESSES(A)
VIL
tAVAV
VIH
CE#(E)
tEHQZ
VIL
VIH
OE#(G)
tGHQZ
VIL
VIH
WE#(W)
tGLQV
tELQV
VIL
tGLQX
tELQX
tOH
VOH
DATA(D/Q)
(DQ0-DQ15)
HIGH Z
Valid Output
VOL
HIGH Z
tAVQV
VCC
tPHQV
VIH
RP#(P)
VIL
Figure 14. AC Waveform for Read Operations
Rev. 1.26
LHF16J02
Standby
VIH
Device
Address Selection
33
Data Valid
Address Stable
ADDRESSES(A)
VIL
tAVAV
VIH
tELQV
CE#(E)
tEHQZ
VIL
tAVQV
VIH
tGLQV
OE#(G)
tGHQZ
VIL
tFVQV
VIH
BYTE#(F)
VIL
tOH
tGLQX
tELFV
VOH
DATA(D/Q)
(DQ0-DQ7)
HIGH Z
Data Output
Valid
Output
HIGH Z
tELQX
VOL
tFLQZ
VOH
DATA(D/Q)
(DQ8-DQ15)
HIGH Z
Data
Output
HIGH Z
VOL
Figure 15. BYTE# timing Waveform
Rev. 1.26
LHF16J02
34
6.2.5 AC CHARACTERISTICS - WRITE OPERATIONS(1)
Sym.
VCC=2.7V-3.6V, TA=0°C to +70°C
Parameter
Notes
Min.
90
1
10
50
100
100
50
50
0
0
10
30
Max.
Unit
ns
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tAVAV
Write Cycle Time
tPHWL
RP# High Recovery to WE# Going Low
2
tELWL
CE# Setup to WE# Going Low
tWLWH WE# Pulse Width
tSHWH
WP#VIH Setup to WE# Going High
2
tVPWH
VCCW Setup to WE# Going High
2
tAVWH
Address Setup to WE# Going High
3
tDVWH
Data Setup to WE# Going High
3
tWHDX
Data Hold from WE# High
tWHAX
Address Hold from WE# High
tWHEH
CE# Hold from WE# High
tWHWL WE# Pulse Width High
tWHRL
WE# High to RY/BY# Going Low or SR.7 Going "0"
100
tWHGL
Write Recovery before Read
0
tQVVL
VCCW Hold from Valid SRD, RY/BY# High Z
2,4
0
tQVSL
WP# VIH Hold from Valid SRD, RY/BY# High Z
2,4
0
tFVWH
BYTE# Setup to WE# Going High
5
50
tWHFV
BYTE# Hold from WE# High
5
90
NOTES:
1. Read timing characteristics during block erase, full chip erase, word/byte write and lock-bit configuration operations are
the same as during read-only operations. Refer to AC Characteristics for read-only operations.
2. Sampled, not 100% tested.
3. Refer to Table 4 for valid AIN and DIN for block erase, full chip erase, word/byte write or lock-bit configuration.
4. VCCW should be held at VCCWH1/2 until determination of block erase, full chip erase, word/byte write or lock-bit
configuration success (SR.1/3/4/5=0).
5. If BYTE# switch during reading cycle, exist the regulations separately.
Rev. 1.26
LHF16J02
ADDRESSES(A)
AIN
AIN
4
5
6
}
}
3
}
2
}
}
}
1
VIH
35
VIL
tWHAX
tAVWH
tAVAV
VIH
CE#(E)
VIL
tELWL
tWHEH
tWHGL
VIH
OE#(G)
VIL
tWHQV1,2,3,4
tWHWL
VIH
WE#(W)
VIL
VIH
DATA(D/Q)
High Z
tWLWH
tDVWH
tWHDX
DIN
Valid
SRD
DIN
VIL
tPHWL
tFVWH
DIN
tWHFV
VIH
BYTE#(F)
VIL
RY/BY#(R)
(SR.7)
High Z
("1")
VOL
("0")
tWHRL
tSHWH
tQVSL
VIH
WP#(S)
VIL
VIH
RP#(P)
VIL
tVPWH
VCCWH1/2
tQVVL
VCCW(V) VCCWLK
VIL
NOTES:
1. VCC power-up and standby.
2. Write each setup command.
3. Write each confirm command or valid address and data.
4. Automated erase or program delay.
5. Read status register data.
6. Write Read Array command.
Figure 16. AC Waveform for WE#-Controlled Write Operations
Rev. 1.26
LHF16J02
36
6.2.6 ALTERNATIVE CE#-CONTROLLED WRITES(1)
Sym.
VCC=2.7V-3.6V, TA=0°C to +70°C
Parameter
Notes
Min.
90
1
0
65
100
100
50
50
0
0
0
25
Max.
Unit
ns
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
tAVAV
Write Cycle Time
tPHEL
RP# High Recovery to CE# Going Low
2
tWLEL
WE# Setup to CE# Going Low
tELEH
CE# Pulse Width
tSHEH
WP#VIH Setup to CE# Going High
2
tVPEH
VCCW Setup to CE# Going High
2
tAVEH
Address Setup to CE# Going High
3
tDVEH
Data Setup to CE# Going High
3
tEHDX
Data Hold from CE# High
tEHAX
Address Hold from CE# High
tEHWH
WE# Hold from CE# High
tEHEL
CE# Pulse Width High
tEHRL
CE# High to RY/BY# Going Low or SR.7 Going "0"
100
tEHGL
Write Recovery before Read
0
tQVVL
VCCW Hold from Valid SRD, RY/BY# High Z
2,4
0
tQVSL
WP# VIH Hold from Valid SRD, RY/BY# High Z
2,4
0
tFVEH
BYTE# Setup to CE# Going High
5
50
tEHFV
BYTE# Hold from CE# High
5
90
NOTES:
1. In systems where CE# defines the write pulse width (within a longer WE# timing waveform), all setup, hold, and inactive
WE# times should be measured relative to the CE# waveform.
2. Sampled, not 100% tested.
3. Refer to Table 4 for valid AIN and DIN for block erase, full chip erase, word/byte write or lock-bit configuration.
4. VCCW should be held at VCCWH1/2 until determination of block erase, full chip erase, word/byte write or lock-bit
configuration success (SR.1/3/4/5=0).
5. If BYTE# switch during reading cycle, exist the regulations separately.
Rev. 1.26
LHF16J02
AIN
AIN
4
5
6
Valid
SRD
DIN
}
}
3
}
2
}
}
}
1
37
VIH
ADDRESSES(A)
VIL
tEHAX
tAVEH
tAVAV
VIH
tEHEL
CE#(E)
VIL
tELEH
tDVEH
VIH
tEHGL
OE#(G)
VIL
VIH
WE#(W)
VIL
VIH
DATA(D/Q)
High Z
tEHQV1,2,3,4
tEHWH
tEHDX
tWLEL
DIN
DIN
VIL
tPHEL
tFVEH
tEHFV
VIH
BYTE#(F)
VIL
RY/BY#(R)
(SR.7)
High Z
("1")
VOL
("0")
tEHRL
tSHEH
tQVSL
VIH
WP#(S)
VIL
VIH
RP#(P)
VIL
tVPEH
VCCWH1/2
tQVVL
VCCW(V) VCCWLK
VIL
NOTES:
1. VCC power-up and standby.
2. Write each setup command.
3. Write each confirm command or valid address and data.
4. Automated erase or program delay.
5. Read status register data.
6. Write Read Array command.
Figure 17. AC Waveform for CE#-Controlled Write Operations
Rev. 1.26
LHF16J02
38
6.2.7 RESET OPERATIONS
High Z
RY/BY#(R) ("1")
(SR.7) VOL
("0")
VIH
RP#(P)
VIL
tPLPH
(A)Reset During Read Array Mode
High Z
RY/BY#(R) ("1")
(SR.7) VOL
("0")
RP#(P)
tPLRZ
VIH
VIL
tPLPH
(B)Reset During Block Erase, Full Chip Erase, Word/Byte Write or Lock-Bit Configuration
2.7V
VCC
VIL
t2VPH
VIH
RP#(P)
VIL
(C)RP# rising Timing
Figure 18. AC Waveform for Reset Operation
Reset AC Specifications
Sym.
tPLPH
tPLRZ
Parameter
RP# Pulse Low Time
RP# Low to Reset during Block Erase, Full Chip Erase,
Word/Byte Write or Lock-Bit Configuration
VCC 2.7V to RP# High
Notes
2
1,2
Min.
100
Max.
Unit
ns
30
µs
t2VPH
2,3
100
ns
NOTES:
1. If RP# is asserted while a block erase, full chip erase, word/byte write or lock-bit configuration operation is not executing,
the reset will complete within 100ns.
2. A reset time, tPHQV, is required from the later of RY/BY#(SR.7) going High Z("1") or RP# going high until outputs are
valid. Refer to AC Characteristics - Read-Only Operations for tPHQV.
3. When the device power-up, holding RP# low minimum 100ns is required after VCC has been in predefined range and also
has been in stable there.
Rev. 1.26
LHF16J02
39
6.2.8 BLOCK ERASE, FULL CHIP ERASE, WORD/BYTE WRITE AND LOCK-BIT
CONFIGURATION PERFORMANCE(3)
Sym.
tWHQV1
tEHQV1
tWHQV2
tEHQV2
VCC=2.7V-3.6V, TA=0°C to +70°C
VCCW=2.7V-3.6V
Parameter
Notes
Typ.(1)
Max.
Word Write Time
32K word Block
2
33
200
4K word Block
2
36
200
Byte Write Time
64K byte Block
2
31
200
8K byte Block
2
32
200
Block Write Time
32K word Block
2
1.1
4
(In word mode)
4K word Block
2
0.15
0.5
Block Write Time
64K byte Block
2
2.2
7
(In byte mode)
8K byte Block
2
0.3
1
32K word Block
Block Erase Time
2
1.2
6
64K byte Block
4K word Block
2
0.6
5
8K byte Block
Full Chip Erase Time
2
42
210
VCCW=11.7V-12.3V
Typ.(1)
Max.
20
27
19
26
0.66
0.12
1.4
0.25
Unit
µs
µs
µs
µs
s
s
s
s
0.9
s
0.5
s
32
s
tWHQV3
Set Lock-Bit Time
2
56
200
42
µs
tEHQV3
tWHQV4
Clear Block Lock-Bits Time
2
1
5
0.69
s
tEHQV4
tWHRZ1 Word/Byte Write Suspend Latency Time to
4
6
15
6
15
µs
tEHRZ1
Read
tWHRZ2 Block Erase Suspend Latency Time to
4
16
30
16
30
µs
tEHRZ2
Read
NOTES:
1. Typical values measured at TA=+25°C and VCC=3.0V, VCCW=3.0V or 12.0V. Assumes corresponding lock-bits are not
set. Subject to change based on device characterization.
2. Excludes system-level overhead.
3. Sampled but not 100% tested.
4. A latency time is required from issuing suspend command(WE# or CE# going high) until RY/BY# going High Z or SR.7
going "1".
Rev. 1.26
ADDITIONAL INFORMATION
1 Block Erase Suspend and Resume command
If the time between writing the Block Erase Resume command and writing the Block Erase Suspend command is shorter
than 15ms and both commands are written repeatedly, a longer time is required than standard block erase until the
completion of the operation.
Rev. 0.11
i
A-1 RECOMMENDED OPERATING CONDITIONS
A-1.1 At Device Power-Up
AC timing illustrated in Figure A-1 is recommended for the supply voltages and the control signals at device power-up.
If the timing in the figure is ignored, the device may not operate correctly.
VCC(min)
VCC
GND
tVR
t2VPH *1
tR
tPHQV
VIH
RP# (P)
(RST#)
VCCW *2 (V)
VIL
VCCWH1/2
(VPPH1/2)
GND
(VPP)
tR or tF
tR or tF
tAVQV
VIH
Valid
Address
ADDRESS (A)
VIL
tF
tR
tELQV
VIH
CE#
(E)
VIL
VIH
WE# (W)
VIL
tF
tR
tGLQV
VIH
OE#
(G)
VIL
VIH
WP#
(S)
VIL
VOH
DATA (D/Q)
VOL
High Z
Valid
Output
*1 t5VPH for the device in 5V operations.
*2 To prevent the unwanted writes, system designers should consider the VCCW (VPP) switch, which connects VCCW (VPP)
to GND during read operations and VCCWH1/2 (VPPH1/2) during write or erase operations.
See the application note AP-007-SW-E for details.
Figure A-1. AC Timing at Device Power-Up
For the AC specifications tVR, tR, tF in the figure, refer to the next page. See the “ELECTRICAL SPECIFICATIONS“
described in specifications for the supply voltage range, the operating temperature and the AC specifications not shown in
the next page.
Rev. 1.10
ii
A-1.1.1 Rise and Fall Time
Symbol
Parameter
Notes
Min.
Max.
Unit
1
0.5
30000
µs/V
tVR
VCC Rise Time
tR
Input Signal Rise Time
1, 2
1
µs/V
tF
Input Signal Fall Time
1, 2
1
µs/V
NOTES:
1. Sampled, not 100% tested.
2. This specification is applied for not only the device power-up but also the normal operations.
tR(Max.) and tF(Max.) for RP# (RST#) are 50µs/V.
Rev. 1.10
iii
A-1.2 Glitch Noises
Do not input the glitch noises which are below VIH (Min.) or above VIL (Max.) on address, data, reset, and control signals,
as shown in Figure A-2 (b). The acceptable glitch noises are illustrated in Figure A-2 (a).
Input Signal
Input Signal
VIH (Min.)
VIH (Min.)
VIL (Max.)
VIL (Max.)
Input Signal
Input Signal
(a) Acceptable Glitch Noises
(b) NOT Acceptable Glitch Noises
Figure A-2. Waveform for Glitch Noises
See the “DC CHARACTERISTICS“ described in specifications for VIH (Min.) and VIL (Max.).
Rev. 1.10
iv
A-2 RELATED DOCUMENT INFORMATION(1)
Document No.
Document Name
AP-001-SD-E
Flash Memory Family Software Drivers
AP-006-PT-E
Data Protection Method of SHARP Flash Memory
AP-007-SW-E
RP#, VPP Electric Potential Switching Circuit
NOTE:
1. International customers should contact their local SHARP or distribution sales office.
Rev. 1.10