PSRL5017R8 Series Up to 800 Watts Single Output with Active PFC AC/DC Switching Power Supply FEATURES ● 2 Year Warranty ● Optional Top Cover Available ● Optional N+1 Active Current Sharing ● Peak Power 900W within 500uS duty duration ● Power Factor Corrected to EN61000-3-2 Class D ● High Power Density (Max. 9.1 Watts per cubic inch) ● Approved to UL/CUL/TUV/CB/CE & Class B Emissions ● U-Chassis & Enclosed with Built-in Fan Mechanical Options SPECIFICATIONS: PSRL5017R8 Series U Type: (U-Chassis): 8(L) x 4.33(W) x 2.5(H) inches E Type: (Enclosed with built-in Fan): 9.17(L) x 4.25(W) x 2.5(H) inches o All specifications are based on 25 C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. INPUT SPECIFICATIONS Input Voltage 180 - 264 VAC Input Current 6A at 180VAC and full load. Input Frequency 47 to 63Hz Inrush Current 70A max. @ 230VAC with full load cold start. Leakage Current 3.5mA max. @ 240VAC. Remote ON/OFF Designated as RSW on CN3, requires a low signal to inhibit output. OUTPUT SPECIFICATIONS Output Voltage See Table Output Power Range 800 Watts max with airflow. (See Note 3) Output Adjustability Output user adjustable ±5% minimum. Total Regulation ±1% Output Current See Table Ripple & Noise (peak to peak) ±1% Transient Response Returns to within 1% in less than 2.5ms for a 50% load change and the peak transient does not excess 5%. Hold-Up Time 20ms min. at 80% of full load. Overshoot Turn-On & Off overshoot < 5% over nominal voltage. Turn On Delay 1 second maximum at 120VAC. Designated as RS+ and RS- on CN3. Voltage compensates for up to 0.5V line drop. Remote Sense (Not available for current sharing models). PROTECTION Over Voltage Protection Unit latching down when output voltage exceeds 130% and recycle AC input to reset. Short Circuit Protection Trip without damage and auto-recovery. Over-Temperature Protection Unit protected of excessive operating ambient 85°C and automatic recovery. Over-Power Protection Fold back mode 110-140% and auto-recovery. Input Voltage Protection Power shut down under 80 ±5VAC, and recovered over 86VAC Input Fusing Protection A T10A/250V fuse inserted in primary. GENERAL SPECIFICATIONS Efficiency 80% for 12V, and 83% minimum for other outputs @ 230VAC and full load. 1500 VAC input line to chassis (10mA DC cut off current); 3000VAC between primary and secondary Withstand Voltage windings. Primary to core 1500VAC. All for 3 seconds. Burn In 45 ±5°C for one hour @ 230VAC with full load. PFC Active power factor correction meets EN61000-3-2 class D. Designated as PG on the CN3 and TTL high 100-500ms after regulation. It goes low at least 1ms before loss Power Good of regulation for Power on Reset signal. Grounding Test Apply 25A from ground pin of the three prong plug to the far most earth. Max allowable resistance is 0.1 ohm. Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSRL5017R8 Series Up to 800 Watts Single Output with Active PFC AC/DC Switching Power Supply SPECIFICATIONS (CONTINUED) GENERAL SPECIFICATIONS (CONTINUED) Designated as CSH on the CN3, optional single wired for forced current sharing function and parallel up to 4 Current Sharing units within 10% accuracy at full load. Current Monitor Designated as CMN on the CN3 is a 0.5V to 3VDC output voltage to represent 0% to 100% output current. Bi-color LED1 emit Green for Power On and emit Orange when protection is enabled or RSW is applied a low LED Display signal. ENVIRONMENTAL SPECIFICATIONS Operating Temperature 0°C to +70°C ambient, de-rating at 2.5% per degree from 50°C to 70°C. Storage Temperature -20°C to +85°C Operating Humidity 5% to 90% RH, non-condensing Storage Humidity 5% to 95% RH, non-condensing Vibration 5 ~ 50Hz, acceleration 7.35 m/(s x s) on X, Y, and Z axis. U Type (U-Chassis): 30CFM to achieve maximum power for all models except PSRL5017R3 Series which is Cooling convection cooled. E Type (Enclosed with built-in fan): Self cooled by built-in fan. MTBF 150,000 hours (according to MIL-HBK-217F) at 30°C. PHYSICAL SPECIFICATIONS U Type (U-Chassis): 1350 grams Weight E Type (Enclosed with built-in fan): 1450 grams U Type (U-Chassis): 8(L) x 4.33(W) x 2.5(H) inches. Dimensions E Type (Enclosed with built-in fan): 9.17(L) x 4.25(W) x 2.5(H) inches. Warranty 2 years SAFETY Emissions FCC part15, CISPR 22 Class B, Conducted. Approved to UL60950-1, CSA C22.2 No. 60950-1-03, TUV EN60950-1, CE Mark (LVD) EN61000-3-2,3, and Safety Regulations IEC61000-4 Series Regulations and CB. OUTPUT VOLTAGE / CURRENT RATING CHART Model Output Voltage Range Preset Voltage Output Current PSRL5017Rx8-12(I) 12 – 15 VDC 12 VDC 62.5A ±1% ±1% 750W PSRL5017Rx8-16(I) 16 – 21 VDC 18 VDC 50A ±1% ±1% 800W PSRL5017Rx8-24(I) 22 – 30 VDC 24 VDC 36.36A ±1% ±1% 800W PSRL5017Rx8-36(I) 31 – 47 VDC 36 VDC 25.8A ±1% ±1% 800W PSRL5017Rx8-48(I) 48 – 56 VDC 48 VDC 16.66A ±1% ±1% 800W Regulation Ripple & Noise Output Power NOTES 1. The PSRL5017R8 Series is designated as PSRL5017Rxw-yz where x = U (U-chassis type) or E (Enclosed with built-in fan type), w = 8 for output power from 750W - 800W, y = 12, 16, 24, 36, or 48 for output voltage, and z can be blank or I where I denotes forced current sharing option (output with internal OR-ring diode). See PSRL5017R-I Series for forced current sharing. 2. All output ranges are covered in agency certifications and preset voltage will be set as standard models. If any request is not preset output, then please contact us in advance. 3. U-Chassis type needs external forced airflow min. 30CFM to achieve maximum power, except PSRL5017RU3-yz which is convection cooled. 4. Ripple & noise are measured from 10KHZ to 20MHz bandwidth at output with parallel 0.1uF ceramic and 22uF electrolytic capacitors. 5. Providing peak power to 900W within 500uS for all models, longer duty duration need contact manufacturer. 6. 1% minimum load is required to maintain the ripple and regulation. 7. Cover is optional for U-Chassis Type. Please call factory for ordering details. 8. Output is fully isolated. Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSRL5017R8 Series Up to 800 Watts Single Output with Active PFC AC/DC Switching Power Supply MECHANICAL DRAWINGS PSRL5017RU8 Series (U-Chassis Type): 8(L) x 4.33(W) x 2.5(H) inches; Weight: 1350g; Option: Top Cover. PSRL5017RE8 Series (Enclosed with built-in Fan Type): 9.17(L) x 4.25(W) x 2.5(H) inches; Weight: 1450g. I/O CONNECTOR PIN ASSIGNMENT AC Input Connector (CN1): Enclosed Type: IEC320 or equivalent Snap-in mounting type or DINKLE Terminal block Part No. DT-35-A02W-03 (3 pin). U-Chassis Type: Mating Molex Part No. 09-91-0700 or equivalent (7 pin. 5 used) or Howder Terminal block Part No. HD-121-3P. Output Connector (CN2): Mating Molex Part No. 09-91-2000 (20 pin) or Howder Terminal block Part No. HD-121-8P (8 pin). Output Pin Assignment: (See table at right) Logic signal connectors (CN3): Mating JST XHP-7 or equivalent (CHYAO SHIUNN JS-2001-07). Output Pin Connection Howder Molex Pins 1 – 4 Pins 1 – 10 Vo+ Vo- Pins 5 – 8 Pins 11 – 20 Fan Drive: 12VDC/500mA Mating JST XHP-2 or equivalent (CHYAO SHIUNN JS-2001-02). Mounting Inserts: 6-32, M4 4 Places individually with maximum penetration 0.2 inch on bottom side and 0.25 inch on both sides. Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797