HMC608LC4 v01.0707 LINEAR & POWER AMPLIFIERS - SMT 5 GaAs PHEMT MEDIUM POWER AMPLIFIER, 9.5 - 11.5 GHz Typical Applications Features The HMC608LC4 is ideal for: Output IP3: +33 dBm • Point-to-Point Radios Saturated Power: +27.5 dBm @ 23% PAE • Point-to-Multi-Point Radios Gain: 29.5 dB • Military End-Use Supply: +5.0V @ 310 mA 50 Ohm Matched Input/Output RoHS Compliant 4x4 mm SMT Package Functional Diagram General Description The HMC608LC4 is a high dynamic range GaAs PHEMT MMIC Medium Power Amplifier housed in a leadless “Pb free” SMT package. The amplifier has two modes of operation: high gain mode (Vpd pin shorted to ground); and low gain mode (Vpd pin left open). The electrical specifications in the table below are shown for the amplifier operating in high gain mode. Operating from 9.5 to 11.5 GHz, the amplifier provides 29.5 dB of gain, +27.5 dBm of saturated power and 23% PAE from a +5.0 V supply voltage. Noise figure is 6 dB while output IP3 is +33 dBm. The RF I/Os are DC blocked and matched to 50 Ohms for ease of use. The HMC608LC4 eliminates the need for wire bonding, allowing use of surface mount manufacturing techniques. Electrical Specifications, TA = +25° C, Vdd1, 2, 3 = 5V, Idd = 310 mA [1], Vpd = GND [2] Parameter Min. Frequency Range Gain [3] 27 Gain Variation Over Temperature Output Third Order Intercept (IP3) 23 dB 0.03 dB/ °C dB 19 dB 27 dBm 27.5 dBm 33 dBm Noise Figure 6.0 Supply Current (Idd = Idd1 +Idd2 +Idd3)(Vdd = +5V, Vgg = -2.6V Typ.) [3] 310 dB 350 [[1] Adjust Vgg between -3 to 0V to achieve Idd = 310 mA typical. [2] Vpd= ground for high gain mode, Vpd = open for low gain mode. [3] In low gain mode, typical gain is 22 dB and typical current is 67 mA. 5 - 310 Units GHz 13 Output Return Loss Saturated Output Power (Psat) Max. 29.5 0.02 Input Return Loss Output Power for 1 dB Compression (P1dB) Typ. 9.5 - 11.5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com mA HMC608LC4 v01.0707 GaAs PHEMT MEDIUM POWER AMPLIFIER, 9.5 - 11.5 GHz 35 30 25 20 15 10 5 0 -5 -10 -15 -20 -25 -30 33 32 S21 S11 S22 31 30 29 28 27 +25C +85C -40C 26 25 24 8 9 10 11 12 13 14 9 9.5 FREQUENCY (GHz) Input Return Loss vs. Temperature 10.5 11 11.5 Output Return Loss vs. Temperature 0 0 -5 RETURN LOSS (dB) -4 RETURN LOSS (dB) 10 FREQUENCY (GHz) -8 -12 +25C +85C -40C -16 +25C +85C -40C -10 -15 -20 -25 -20 -30 9 9.5 10 10.5 11 11.5 9 9.5 FREQUENCY (GHz) 11 11.5 11 11.5 Psat vs. Temperature 35 30 30 25 25 Psat (dBm) 35 20 +25C +85C -40C 10 10.5 FREQUENCY (GHz) P1dB vs. Temperature 15 10 LINEAR & POWER AMPLIFIERS - SMT 34 7 P1dB (dBm) 5 Gain vs. Temperature GAIN (dB) RESPONSE (dB) Broadband Gain & Return Loss 20 15 +25C +85C -40C 10 5 5 0 0 9 9.5 10 10.5 FREQUENCY (GHz) 11 11.5 9 9.5 10 10.5 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 311 HMC608LC4 v01.0707 Output IP3 vs. Temperature Noise Figure vs. Temperature 40 10 35 9 8 NOISE FIGURE (dB) OIP3 (dBm) 30 25 20 15 +25C +85C -40C 10 7 6 5 4 3 +25C +85C -40C 2 5 1 0 0 9 9.5 10 10.5 11 11.5 9 9.5 10 FREQUENCY (GHz) 11.5 0 35 34 -10 ISOLATION (dB) 33 32 31 30 Gain P1dB Psat OIP3 29 28 -20 +25C +85C -40C -30 -40 -50 27 -60 26 -70 25 4.5 5 9 5.5 9.5 10 30 3.5 POWER DISSIPATION (W) 4 25 20 15 10 Pout Gain PAE 5 -18 -16 -14 -12 -10 -8 Pin (dBm) -6 -4 11 11.5 Power Dissipation 35 0 -20 10.5 FREQUENCY (GHz) Power Compression @ 10.3 GHz Pout (dBm), GAIN (dB), PAE (%) 11 Reverse Isolation vs. Temperature Vdd Supply Voltage (Vdc) 5 - 312 10.5 FREQUENCY (GHz) Gain, Power & OIP3 vs. Supply Voltage @ 10.3 GHz GAIN (dB), P1dB(dBm), Psat (dBm), OIP3(dBm) LINEAR & POWER AMPLIFIERS - SMT 5 GaAs PHEMT MEDIUM POWER AMPLIFIER, 9.5 - 11.5 GHz -2 0 2 9 GHz 9.5 GHz 10 GHz 10.5 GHz 11.0 GHz 11.5 GHz 3 2.5 2 1.5 1 -30 -25 -20 -15 -10 -5 INPUT POWER (dBm) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 0 HMC608LC4 v01.0707 GaAs PHEMT MEDIUM POWER AMPLIFIER, 9.5 - 11.5 GHz Low Gain Mode, Gain vs. Temperature 25 30 20 28 15 26 24 S21 S11 S22 5 0 GAIN (dB) RESPONSE (dB) 10 -5 -10 -15 22 20 18 16 +25C +85C -40C -20 14 -25 12 -30 -35 10 7 8 9 10 11 12 13 14 9 9.5 FREQUENCY (GHz) 0 0 -4 -5 -8 -12 +25C +85C -40C -20 10.5 11 11.5 Low Gain Mode, Output Return Loss vs. Temperature RETURN LOSS (dB) RETURN LOSS (dB) Low Gain Mode, Input Return Loss vs. Temperature -16 10 FREQUENCY (GHz) +25C +85C -40C -10 -15 -20 -25 -24 -30 9 9.5 10 10.5 FREQUENCY (GHz) 11 11.5 9 9.5 10 10.5 11 5 LINEAR & POWER AMPLIFIERS - SMT Low Gain Mode, Broadband Gain & Return Loss 11.5 FREQUENCY (GHz) For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 313 HMC608LC4 v01.0707 LINEAR & POWER AMPLIFIERS - SMT 5 Absolute Maximum Ratings Drain Bias Voltage (Vdd1, Vdd2, Vdd3) 7 Vdc Gate Bias Voltage (Vgg) -4.0 to -1.0 Vdc GaAs PHEMT MEDIUM POWER AMPLIFIER, 9.5 - 11.5 GHz Typical Supply Current vs. Vdd Vdd (Vdc) Idd (mA) +4.5 300 RF Input Power (RFin)(Vdd = +5.0 Vdc) +10 dBm +5.0 310 Channel Temperature 175 °C +5.5 325 Continuous Pdiss (T= 85 °C) (derate 22.18 mW/°C above 85 °C) 2W Thermal Resistance (channel to ground paddle) 45 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C Note: Amplifier will operate over full voltage ranges shown above. Vgg adjusted to achieve Idd= 310 mA at +5.0V. ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS Outline Drawing NOTES: 1. PACKAGE BODY MATERIAL: ALUMINA. 2. LEAD AND GROUND PADDLE PLATING: 30-80 MICROINCHES GOLD OVER 50 MICROINCHES MINIMUM NICKEL 3. DIMENSIONS ARE IN INCHES (MILLIMETERS). 4. LEAD SPACING TOLERANCE IS NON-CUMULATIVE. 5. CHARACTERS TO BE HELVETICA MEDIUM, .025 HIGH, BLACK INK, OR LASER MARK LOCATED APPROX. AS SHOWN. 6. PACKAGE WARP SHALL NOT EXCEED 0.05MM DATUM – C – 7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 5 - 314 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC608LC4 v01.0707 GaAs PHEMT MEDIUM POWER AMPLIFIER, 9.5 - 11.5 GHz Pin Number Function Description 1 Vgg Gate control for amplifier. Adjust to achieve Id of 310 mA. Please follow “MMIC Amplifier Biasing Procedure” Application Note. External bypass capacitors of 100 pF, 1000 pF and 2.2 μF are required. 2, 3, 7 - 12, 16 - 18, 22, 24 N/C No connection required. These pins may be connected to RF/DC ground without affecting performance. 4, 6, 13, 15 GND Package bottom has an exposed metal paddle that must also be connected to RF/DC ground. 5 RFIN This pin is AC coupled and matched to 50 Ohms. 14 RFOUT This pin is AC coupled and matched to 50 Ohms. 21, 20, 19 Vdd1, Vdd2, Vdd3 Power Supply Voltage for the amplifier. External bypass capacitors of 100 pF, 1000pF, and 2.2 μF are required. 23 Vpd High gain (connect to ground) / low gain mode pin control (open circuit). External bypass capacitors of 100 pF, 1000 pF and 2.2 μF are required. Interface Schematic For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com LINEAR & POWER AMPLIFIERS - SMT 5 Pin Descriptions 5 - 315 HMC608LC4 v01.0707 Evaluation PCB LINEAR & POWER AMPLIFIERS - SMT 5 GaAs PHEMT MEDIUM POWER AMPLIFIER, 9.5 - 11.5 GHz List of Materials for Evaluation PCB 112763 [1] Item J1, J2 Description PC mount SMA connector J3 - J8 DC Pin C1 - C6 100 pF capacitor, 0402 pkg. C6 - C10 1,000 pF Capacitor, 0603 pkg. C11 - C15 2.2μF Capacitor, Tantalum U1 HMC608LC4 Amplifier PCB [2] 112761 Evaluation PCB [1] Reference this number when ordering complete evlaution PCB [2] Circuit Board Material: Rogers 4350. 5 - 316 The circuit board used in this application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation board should be mounted to an appropriate heat sink. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC608LC4 v01.0707 GaAs PHEMT MEDIUM POWER AMPLIFIER, 9.5 - 11.5 GHz 5 LINEAR & POWER AMPLIFIERS - SMT Notes: For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 5 - 317