TSV991, TSV992, TSV994, TSV991A, TSV992A, TSV994A Rail-to-rail input/output 20 MHz GBP operational amplifiers Datasheet − production data Features ■ Low input offset voltage: 1.5 mV max (A grade) ■ Rail-to-rail input and output ■ Wide bandwidth 20 MHz ■ Stable for gain ≥ 4 or ≤ -3 ■ Low power consumption: 820 µA typ ■ High output current: 35 mA ■ Operating from 2.5 V to 5.5 V ■ Low input bias current, 1 pA typ ■ ESD internal protection ≥ 5 kV SOT23-5 See TSV91 series for unity-gain stable amplifiers Applications ■ Battery-powered applications ■ Portable devices ■ Signal conditioning and active filtering ■ Medical instrumentation ■ Automotive applications /54 6## ). 6## ). DFN8 2x2 Related products ■ Pin connections (top view) ). 6## ). 6## 6## /54 .# .# MiniSO-8, SO-8 /54 ). ). 6## 6## /54 ). ). Description The TSV991, TSV992 and TSV994 family of single, dual, and quad operational amplifiers offers low voltage operation and rail-to-rail input and output. These devices feature an excellent speed/power consumption ratio, offering a 20 MHz gainbandwidth, stable for gains above 4 (100 pF capacitive load), while consuming only 1.1 mA maximum at 5 V. They also feature an ultra-low input bias current. These characteristics make the TSV99x family ideal for sensor interfaces, battery-supplied and portable applications, as well as active filtering. October 2012 This is information on a product in full production. Doc ID 12833 Rev 9 SO-14, TSSOP14 /54 /54 ). ). ). ). 6## 6## ). ). ). ). /54 /54 1/25 www.st.com 25 Contents TSV99x, TSV99xA Contents 1 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 3.1 Driving resistive and capacitive loads . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.2 PCB layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3.3 Macromodel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.1 SOT23-5 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.2 DFN8 2x2 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 4.3 MiniSO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 4.4 SO-8 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 4.5 TSSOP14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.6 SO-14 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 2/25 Doc ID 12833 Rev 9 TSV99x, TSV99xA 1 Absolute maximum ratings and operating conditions Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Symbol VCC Vid Vin Iin Parameter (1) Supply voltage Differential input voltage (2) Value Unit 6 V ±VCC V (3) VCC- -0.2 to VCC+ +0.2 V (4) 10 mA -65 to +150 °C Input voltage Input current Tstg Storage temperature Rthja Thermal resistance junction to ambient(5)(6) DFN8 2x2 SOT23-5 SO-8 MiniSO-8 SO-14 TSSOP14 57 250 125 190 103 100 Rthjc Thermal resistance junction to case SOT23-5 SO-8 MiniSO-8 SO-14 TSSOP14 81 40 39 31 32 Maximum junction temperature 150 °C 5 kV 400 V Tj HBM: Human body MM: Machine ESD model(7) model(8) CDM: Charged device model(9) SOT23-5, SO-8, MiniSO-8 DFN8 2x2 TSSOP14 SO-14 1500 1500 750 500 Latch-up immunity 200 °C/W °C/W V mA 1. Value with respect to VDD pin. 2. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal. 3. VCC-Vin must not exceed 6 V. 4. Input current must be limited by a resistor in series with the inputs. 5. Short-circuits can cause excessive heating and destructive dissipation. 6. Rth are typical values. 7. Human body model: 100 pF discharged through a 1.5 kΩ resistor between two pins of the device, done for all couples of pin combinations with other pins floating. 8. Machine model: 200 pF charged to the specified voltage, then discharged directly between two pins of the device with no external series resistor (internal resistor < 5 Ω), done for all couples of pin combinations with other pins floating. 9. Charged device model: all pins plus package are charged together to the specified voltage and then discharged directly to the ground. Doc ID 12833 Rev 9 3/25 Absolute maximum ratings and operating conditions Table 2. Operating conditions Symbol 4/25 TSV99x, TSV99xA Parameter VCC Supply voltage Vicm Common mode input voltage range Top Operating free air temperature range Doc ID 12833 Rev 9 Value Unit 2.5 to 5.5 V VCC- -0.1 to VCC+ +0.1 V -40 to +125 °C TSV99x, TSV99xA Electrical characteristics 2 Electrical characteristics Table 3. Electrical characteristics at VCC+ = +2.5 V, VCC- = 0 V, Vicm = VCC/2, with RL connected to VCC/2, full temperature range (unless otherwise specified)(1) Symbol Parameter Conditions Min. Typ. Max. 0.1 4.5 Unit DC performance Offset voltage TSV99x Vio Offset voltage TSV99xA Top = 25° C Tmin < Top < Tmax 7.5 Top = 25° C 1.5 Tmin < Top < Tmax 3 ΔVio/ΔT Input offset voltage drift 2 Iio Input offset current(2) (Vout = VCC/2) Top = 25° C Iib Input bias current(2) (Vout = VCC/2) Top = 25° C Common mode rejection ratio 20 log (ΔVic/ΔVio) 0 V to 2.5 V, Vout = 1.25 V, Top = 25° C 58 Tmin < Top < Tmax 53 RL= 10 kΩ, Vout = 0.5 V to 2 V, Top = 25° C 80 Tmin < Top < Tmax 75 CMR Avd Large signal voltage gain VCCVOH High level output voltage VOL Low level output voltage Isink Iout Isource ICC Supply current (per operator) 1 Tmin < Top < Tmax µV/°C 10 100 1 Tmin < Top < Tmax 10 pA 100 75 dB 89 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 Ω, Tmin < Top < Tmax 45 150 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 Ω, Tmin < Top < Tmax 45 150 Vo = 2.5 V, Top = 25° C 18 Tmin < Top < Tmax 16 Vo = 0 V, T = 25° C 18 Tmin < Top < Tmax 16 No load, Vout = VCC/2, Tmin < Top < Tmax mV mV 32 35 0.78 mA 1.1 AC performance GBP Gain bandwidth product RL = 2 kΩ, CL = 100 pF, f = 100 kHz, Top = 25° C 20 MHz Phase margin = 45°, Rf = 10kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25° C Gain SR Minimum gain for stability Slew rate Positive gain configuration 4 Negative gain configuration -3 RL = 2kΩ, CL = 100 pF, Top = 25° C Doc ID 12833 Rev 9 10 V/V V/µs 5/25 Electrical characteristics Table 3. Electrical characteristics at VCC+ = +2.5 V, VCC- = 0 V, Vicm = VCC/2, with RL connected to VCC/2, full temperature range (unless otherwise specified)(1) Symbol en TSV99x, TSV99xA Parameter Equivalent input noise voltage THD+N Total harmonic distortion Conditions Min. f = 10 kHz, Top = 25° C Typ. Max. nV -----------Hz 21 G = -3, f = 1 kHz, RL = 2 kΩ, Bw = 22 kHz, Vicm = VCC/2, Vout = 2 Vpp, Top = 25° C Unit 0.0025 % 1. All parameter limits at temperatures other than 25° C are guaranteed by correlation. 2. Guaranteed by design. Table 4. Electrical characteristics at VCC+ = +3.3 V, VCC- = 0 V, Vicm = VCC/2, with RL connected to VCC/2, full temperature range (unless otherwise specified)(1) Symbol Parameter Conditions Min. Typ. Max. 0.1 4.5 Unit DC performance Offset voltage TSV99x Vio Offset voltage TSV99xA Top = 25° C Tmin < Top < Tmax 7.5 Top = 25° C 1.5 mV Tmin < Top < Tmax ΔVio/ΔT Input offset voltage drift 3 - Top = 25° C Iio Input offset current(2) (Vout = VCC/2) Iib Input bias current(2) (Vout = VCC/2) Top = 25° C Common mode rejection ratio 20 log (ΔVic/ΔVio) 0 V to 3.3 V, Vout = 1.65 V, Top = 25° C 60 Tmin < Top < Tmax 55 RL = 10 kΩ, Vout = 0.5 V to 2.8 V, T=25° C 80 Tmin < Top < Tmax 75 CMR Avd Large signal voltage gain VCCVOH High level output voltage VOL Low level output voltage Isink Iout Isource ICC 6/25 2 - 1 10 Tmin < Top < Tmax 100 pA 1 Tmin < Top < Tmax 10 100 78 dB 90 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 Ω, Tmin < Top < Tmax 45 150 RL = 10 kΩ, Tmin < Top < Tmax RL = 600 Ω, Tmin < Top < Tmax - 15 45 40 150 Vo = 3.3 V, Top = 25° C 18 32 Tmin < Top < Tmax 16 Vo = 0 V, Top = 25° C 18 Tmin < Top < Tmax 16 Supply current (per operator) No load, Vout = VCC/2, Tmin < Top < Tmax Doc ID 12833 Rev 9 µV/°C mA 35 0.8 mV 1.1 TSV99x, TSV99xA Table 4. Electrical characteristics Electrical characteristics at VCC+ = +3.3 V, VCC- = 0 V, Vicm = VCC/2, with RL connected to VCC/2, full temperature range (unless otherwise specified)(1) (continued) Symbol Parameter Conditions Min. Typ. Max. Unit AC performance GBP Gain bandwidth product RL = 2 kΩ, CL = 100 pF, f = 100 kHz, Top = 25° C 20 MHz Phase margin = 45°, Rf = 10kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25° C Gain Minimum gain for stability Positive gain configuration 4 Negative gain configuration -3 V/V SR Slew rate RL = 2 kΩ, CL = 100 pF, f = 100 kHz, Top = 25° C 10 V/µs en Equivalent input noise voltage f = 10 kHz, Top = 25° C 21 nV -----------Hz 0.0018 % THD+N Total harmonic distortion G = -3, f = 1 kHz, RL = 2 kΩ, Bw = 22 kHz, Vicm = VCC/2, Vout = 2.8 Vpp, Top = 25° C 1. All parameter limits at temperatures other than 25°C are guaranteed by correlation. 2. Guaranteed by design. Table 5. Electrical characteristics at VCC+ = +5 V, VCC- = 0 V, Vicm = VCC/2, RL connected to VCC/2, full temperature range (unless otherwise specified)(1) Symbol Parameter Conditions Min. Typ. Max. 0.1 4.5 Unit DC performance Offset voltage TSV99x Vio Offset voltage TSV99xA Top = 25° C Tmin < Top < Tmax 7.5 Top = 25° C 1.5 Tmin < Top < Tmax ΔVio/ΔT Input offset voltage drift Iio Input offset current(2) (Vout = VCC/2) Iib Input bias current(2) (Vout = VCC/2) CMR Common mode rejection ratio, 20 log (ΔVic/ΔVio) SVR Supply voltage rejection ratio, 20 log (ΔVcc/ΔVio) Avd Large signal voltage gain 3 - Top = 25° C 2 - 1 10 Tmin < Top < Tmax 100 Top = 25° C 1 Tmin < Top < Tmax 10 µV/°C pA 100 0 V to 5 V, Vout = 2.5 V,Top = 25° C 62 Tmin < Top < Tmax 57 VCC = 2.5 to 5 V 70 86 RL = 10 kΩ, Vout = 0.5 V to 4.5 V, T = 25° C 80 91 Tmin < Top < Tmax 75 Doc ID 12833 Rev 9 mV 82 dB 7/25 Electrical characteristics Table 5. Electrical characteristics at VCC+ = +5 V, VCC- = 0 V, Vicm = VCC/2, RL connected to VCC/2, full temperature range (unless otherwise specified)(1) Symbol VCCVOH VOL TSV99x, TSV99xA Parameter Conditions High level output voltage Low level output voltage Isink Iout Isource ICC Supply current (per operator) Min. Typ. Max. RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 Ω, Tmin < Top < Tmax 45 150 RL = 10 kΩ, Tmin < Top < Tmax 15 40 RL = 600 Ω, Tmin < Top < Tmax 45 150 Vo = 5 V, Top = 25° C 18 Tmin < Tamb < Tmax 16 Vo = 0 V, Top = 25° C 18 Tmin < Tamb < Tmax 16 Unit mV 32 mA 35 No load, Vout = 2.5 V, Tmin < Top < Tmax 0.82 mA 1.1 AC performance GBP RL = 2 kΩ, CL = 100 pF, f = 100 kHz, Top = 25° C Gain bandwidth product 20 MHz Phase margin = 45°, Rf = 10kΩ, RL = 2 kΩ, CL = 100 pF, Top = 25° C Gain Minimum gain for stability Positive gain configuration 4 Negative gain configuration -3 SR Slew rate RL = 2 kΩ, CL = 100 pF, Top = 25° C 10 en Equivalent input noise voltage f = 10 kHz, Top = 25° C 21 G = -3, f = 1 kHz, RL = 2 kΩ, Bw = 22 kHz, Vicm = VCC/2, Vout = 4.4 Vpp, Top = 25° C THD+N Total harmonic distortion V/V V/µs nV -----------Hz 0.0014 % 1. All parameter limits at temperatures other than 25°C are guaranteed by correlation. 2. Guaranteed by design. Figure 1. Input offset voltage distribution at T = 25° C Figure 2. Input offset voltage distribution at T = 125° C 40 140 Vcc=5V Vicm=2.5V Tamb=25°C 120 ° Quantity of parts Quantity of parts 30 100 80 60 40 20 10 20 0 -5 -4 -3 -2 -1 0 1 2 3 4 5 0 -5 8/25 -4 -3 -2 -1 0 1 2 Input offset Voltage (mV) Input offset Voltage (mV) Doc ID 12833 Rev 9 3 4 5 TSV99x, TSV99xA Electrical characteristics Figure 3. Supply current vs. input common mode voltage at VCC = 2.5 V Figure 4. Figure 5. Output current vs. output voltage at Figure 6. VCC = 2.5 V Doc ID 12833 Rev 9 Supply current vs. input common mode voltage at VCC = 5 V Output current vs. output voltage at VCC = 5 V 9/25 Electrical characteristics Voltage gain and phase vs frequency at VCC = 5 V and Vicm = 0.5 V Figure 9. Positive slew rate Figure 8. Voltage gain and phase vs frequency at VCC = 5 V and Vicm = 2.5 V Figure 10. Negative slew rate Phase (°) Phase (°) Figure 7. TSV99x, TSV99xA Vin : from 0.5V to Vcc-0.5V SR : calculated from 10% to 90% Vin : from 0.5V to Vcc-0.5V SR : calculated from 10% to 90% Figure 11. Distortion + noise vs. frequency 10/25 Figure 12. Distortion + noise vs. output voltage Doc ID 12833 Rev 9 TSV99x, TSV99xA Figure 13. Noise vs. frequency Electrical characteristics Figure 14. Supply current vs. supply voltage Doc ID 12833 Rev 9 11/25 Application information TSV99x, TSV99xA 3 Application information 3.1 Driving resistive and capacitive loads These products are low-voltage, low-power operational amplifiers optimized to drive rather large resistive loads above 2 kΩ.. TSV99x products are not unity gain stable. To ensure proper stability they must be used in a gain configuration, with a minimum gain of -3 or +4. However, they can be used in a “follower“ configuration by adding a small, in-series resistor at the output, which drastically improves the stability of the device (Figure 15 shows the recommended in-series resistor values). Once the in-series resistor value has been selected, the stability of the circuit should be tested on the bench and simulated with the simulation model. Figure 15. In-series resistor vs. capacitive Figure 16. Peaking versus capacitive load, load when TSV99x used in follower with or without feedback capacitor configuration in inverting gain configuration Another way to improve stability and reduce peaking is to add a capacitor in parallel with the feedback resistor. As shown in Figure 16, the feedback capacitor drastically reduces the peaking versus capacitive load (inverting gain configuration, gain = -2). 3.2 PCB layouts For correct operation, it is advised to add 10 nF decoupling capacitors as close as possible to the power supply pins. 12/25 Doc ID 12833 Rev 9 TSV99x, TSV99xA 3.3 Application information Macromodel An accurate macromodel of the TSV99x is available on STMicroelectronics’ web site at www.st.com. This model is a trade-off between accuracy and complexity (that is, time simulation) of the TSV99x operational amplifiers. It emulates the nominal performances of a typical device within the specified operating conditions mentioned in the datasheet. It helps to validate a design approach and to select the right operational amplifier, however, it does not replace on-board measurements. Doc ID 12833 Rev 9 13/25 Package information 4 TSV99x, TSV99xA Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 14/25 Doc ID 12833 Rev 9 TSV99x, TSV99xA 4.1 Package information SOT23-5 package information Figure 17. SOT23-5 package mechanical drawing Table 6. SOT23-5 package mechanical data Dimensions Ref. A Millimeters Inches Min. Typ. Max. Min. Typ. Max. 0.90 1.20 1.45 0.035 0.047 0.057 A1 0.15 0.006 A2 0.90 1.05 1.30 0.035 0.041 0.051 B 0.35 0.40 0.50 0.013 0.015 0.019 C 0.09 0.15 0.20 0.003 0.006 0.008 D 2.80 2.90 3.00 0.110 0.114 0.118 D1 1.90 0.075 e 0.95 0.037 E 2.60 2.80 3.00 0.102 0.110 0.118 F 1.50 1.60 1.75 0.059 0.063 0.069 L 0.10 0.35 0.60 0.004 0.013 0.023 K 0 degrees 10 degrees Doc ID 12833 Rev 9 15/25 Package information 4.2 TSV99x, TSV99xA DFN8 2x2 package information Figure 18. DFN8 2x2 package mechanical drawing $&.?X?6??" 16/25 Doc ID 12833 Rev 9 TSV99x, TSV99xA Table 7. Package information DFN8 2x2 package mechanical data Dimensions Ref. A Inches(1) Millimeters Min. Typ. Max. Min. Typ. Max. 0.51 0.55 0.60 0.020 0.022 0.024 A1 0.05 A3 0.002 0.15 0.006 b 0.18 0.25 0.30 0.007 0.010 0.012 D 1.85 2.00 2.15 0.073 0.079 0.085 D2 1.45 1.60 1.70 0.057 0.063 0.067 E 1.85 2.00 2.15 0.073 0.079 0.085 E2 0.75 0.90 1.00 0.030 0.035 0.039 e 0.50 0.020 L 0.50 0.020 ddd 0.08 0.003 1. Values in inches are rounded to three decimal digits. Figure 19. DFN8 2x2 footprint recommendation MM MM MM MM MM MM $&.?X?6?FOOTPRINT??" Doc ID 12833 Rev 9 17/25 Package information 4.3 TSV99x, TSV99xA MiniSO-8 package information Figure 20. MiniSO-8 package mechanical drawing Table 8. MiniSO-8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.1 A1 0 A2 0.75 b Max. 0.043 0.15 0 0.95 0.030 0.22 0.40 0.009 0.016 c 0.08 0.23 0.003 0.009 D 2.80 3.00 3.20 0.11 0.118 0.126 E 4.65 4.90 5.15 0.183 0.193 0.203 E1 2.80 3.00 3.10 0.11 0.118 0.122 e L 0.85 0.65 0.40 0.60 0.006 0.033 0.80 0.016 0.024 0.95 0.037 L2 0.25 0.010 ccc 0° 0.037 0.026 L1 k 18/25 Inches 8° 0.10 Doc ID 12833 Rev 9 0° 0.031 8° 0.004 TSV99x, TSV99xA 4.4 Package information SO-8 package information Figure 21. SO-8 package mechanical drawing Table 9. SO-8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.75 0.069 A1 0.10 A2 1.25 b 0.28 0.48 0.011 0.019 c 0.17 0.23 0.007 0.010 D 4.80 4.90 5.00 0.189 0.193 0.197 E 5.80 6.00 6.20 0.228 0.236 0.244 E1 3.80 3.90 4.00 0.150 0.154 0.157 e 0.25 Max. 0.004 0.010 0.049 1.27 0.050 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 L1 k ccc 1.04 0 0.040 8° 0.10 Doc ID 12833 Rev 9 1° 8° 0.004 19/25 Package information 4.5 TSV99x, TSV99xA TSSOP14 package information Figure 22. TSSOP14 package mechanical drawing Table 10. TSSOP14 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Max. Min. Typ. 1.20 A1 0.05 A2 0.80 b Max. 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 4.90 5.00 5.10 0.193 0.197 0.201 E 6.20 6.40 6.60 0.244 0.252 0.260 E1 4.30 4.40 4.50 0.169 0.173 0.176 e L k aaa 1.00 0.65 0.45 L1 20/25 Inches 0.60 0.0256 0.75 0.018 1.00 0° 0.024 0.030 0.039 8° 0.10 Doc ID 12833 Rev 9 0° 8° 0.004 TSV99x, TSV99xA 4.6 Package information SO-14 package information Figure 23. SO-14 package mechanical drawing Table 11. SO-14 package mechanical data Dimensions Millimeters Inches Ref. Min. Typ. Max. Min. Typ. Max. A 1.35 1.75 0.05 0.068 A1 0.10 0.25 0.004 0.009 A2 1.10 1.65 0.04 0.06 B 0.33 0.51 0.01 0.02 C 0.19 0.25 0.007 0.009 D 8.55 8.75 0.33 0.34 E 3.80 4.0 0.15 0.15 e 1.27 0.05 H 5.80 6.20 0.22 0.24 h 0.25 0.50 0.009 0.02 L 0.40 1.27 0.015 0.05 k ddd 8° (max.) 0.10 Doc ID 12833 Rev 9 0.004 21/25 Ordering information 5 TSV99x, TSV99xA Ordering information Table 12. Order codes(1) Order code Temperature range Package Packing Marking K130 TSV991ILT SOT23-5 TSV991AILT K129 TSV991IQ2T DFN8 2x2 Tape & reel K1E TSV992IST K132 MiniSO-8 TSV992AIST K135 TSV992ID TSV992IDT -40° C to +125° C TSV992AID TSV992AIDT Tube Tape & reel V992I Tube Tape & reel V992AI SO-8 TSV994IPT V994I TSSOP14 Tape & reel TSV994AIPT V994AI TSV994ID TSV994IDT SO-14(1) TSV994AID TSV994AIDT Tube Tape & reel V994I Tube Tape & reel V994AI TSV991IYLT(2) K149 SOT23-5 TSV991AIYLT(2) TSV992IYDT K150 (2) TSV992AIYST(2) TSV994IYDT(2) TSV994AIYDT (2) Tape & reel V992IY Tape & reel V992AY SO-8 TSV992AIYDT(2) TSV992IYST(2) Tape & reel -40° C to +125° C Automotive grade K149 MiniSO-8 Tape & reel K150 SO-14(1) Tape & reel V994IY Tape & reel V994AY TSV994IYPT(2) TSV994AIYPT(2) V994IY TSSOP14 Tape & reel V994AY 1. All packages are Moisture Sensitivity Level 1 as per Jedec J-STD-020-C, except SO-14 which is Jedec level 3. 2. Qualified and characterized according to AEC Q100 and Q003 or equivalent, advanced screening according to AEC Q001 & Q 002 or equivalent. 22/25 Doc ID 12833 Rev 9 TSV99x, TSV99xA 6 Revision history Revision history Table 13. Document revision history Date Revision 31-Jul-2006 1 Preliminary data release for product under development. 07-Nov-2006 2 Final version of datasheet. 12-Dec-2006 3 Noise and distortion figures added. 4 ESD tolerance modified for SO-14, CDM in Table 1: Absolute maximum ratings. Automotive grade commercial products added in Table 12: Order codes. Note about SO-14 added in Table 12: Order codes. Limits in temperature added in Section 2: Electrical characteristics. 5 Corrected MiniSO-8 package information. Corrected footnote for automotive grade order codes in order code table. Improved presentation of package information. 6 Added input current information in table Table 1: Absolute maximum ratings. Added Chapter 3: Application information. Updated all packages in Chapter 4: Package information. Added new order codes: TSV991IYLT, TSV991AIYLT, TSV992IYST, TSV992AIYST, TSV994IYPT, TSV994AIYPT in Table 12: Order codes. 7 Added A versions of devices in title on cover page. Added parameters for full temperature range in Table 3, Table 4, Table 5. Removed gain margin and phase margin parameters in Table 3, Table 4 and Table 5. These parameters have been replaced by the gain parameter (minimum gain for stability). Added Figure 14 and Figure 16. 8 Added parameters for full temperature range in Table 3, Table 4 and Table 5. Modified Note 2 relative to automotive grade in Table 12: Order codes. 07-Jun-2007 11-Feb-2008 25-May-2009 19-Oct-2009 14-Jan-2010 22-Oct-2012 9 Changes Document status changed to production data. Modified gain value in Features and Description. Added DFN8 2x2 pin connection diagram. Table 1: Absolute maximum ratings: added package DFN8 2x2 to rows Rthja and ESD. Table 3, Table 4, and Table 5: replaced “DVio” with ΔVio/ΔT; modified “Gain” and “THD+N” conditions and typical values. Figure 7 and Figure 8: added arrows indicating “Gain” and ‘Phase”. Doc ID 12833 Rev 9 23/25 Revision history TSV99x, TSV99xA Table 13. Document revision history Date 22-Oct-2012 24/25 Revision 9 cont’d Changes Figure 11 and Figure 12: updated. Added Figure 18: DFN8 2x2 package mechanical drawing and Figure 19: DFN8 2x2 footprint recommendation. Table 12: Order codes: updated automotive grade qualification and added order code of DFN8 package. Doc ID 12833 Rev 9 TSV99x, TSV99xA Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2012 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com Doc ID 12833 Rev 9 25/25