AD ADG3300

Low Voltage 1.15 V to 5.5 V, 8-Channel
Bidirectional Logic Level Translator
ADG3300
FUNCTIONAL BLOCK DIAGRAM
Bidirectional level translation
Operates from 1.15 V to 5.5 V
Low quiescent current <1 µA
No direction pin
VCCA
APPLICATIONS
Low voltage ASIC level translation
Smart card readers
Cell phones and cell phone cradles
Portable communications devices
Telecommunications equipment
Network switches and routers
Storage systems (SAN/NAS)
Computing/server applications
GPS
Portable POS systems
Low cost serial interfaces
VCCY
A1
Y1
A2
Y2
A3
Y3
A4
Y4
A5
Y5
A6
Y6
A7
Y7
A8
Y8
EN
GND
05061-001
FEATURES
Figure 1.
GENERAL DESCRIPTION
The ADG3300 is a bidirectional logic level translator that contains eight bidirectional channels. It can be used in multivoltage
digital system applications such as data transfer between a low
voltage DSP/controller and a higher voltage device. The internal
architecture allows the device to perform bidirectional logic
level translation without an additional signal to set the direction
of the translation.
The voltage applied to VCCA sets the logic levels on the A side of
the device, while VCCY sets the levels on the Y side. For proper
operation, VCCA must always be less than VCCY. The VCCA-compatible logic signals applied to the A side of the device appear as
VCCY-compatible levels on the Y side. Similarly, VCCY-compatible
logic levels applied to the Y side of the device appear as VCCAcompatible logic levels on the A side.
The enable pin provides three-state operation of the Y side pins.
When the enable pin (EN) is pulled low, the A1 to A8 pins are
internally pulled down by 6 kΩ resistors, while the Y terminals
are in the high impedance state. The EN pin is referred to VCCA
supply voltage and driven high for normal operation.
The ADG3300 is available in a compact 20-lead TSSOP package,
and it is guaranteed to operate over the 1.15 V to 5.5 V supply
voltage range and extended −40°C to +85°C temperature range.
PRODUCT HIGHLIGHTS
1.
Bidirectional level translation.
2.
Fully guaranteed over the 1.15 V to 5.5 V supply range.
3.
No direction pin.
4.
20-lead TSSOP package.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
ADG3300
TABLE OF CONTENTS
Specifications..................................................................................... 3
Input Driving Requirements..................................................... 15
Absolute Maximum Ratings............................................................ 6
Output Load Requirements ...................................................... 15
ESD Caution.................................................................................. 6
Enable Operation ....................................................................... 15
Pin Configuration and Function Descriptions............................. 7
Power Supplies............................................................................ 15
Typical Performance Characteristics ............................................. 8
Data Rate ..................................................................................... 16
Test Circuits..................................................................................... 12
Applications..................................................................................... 17
Terminology .................................................................................... 14
Layout Guidelines....................................................................... 17
Theory of Operation ...................................................................... 15
Outline Dimensions ....................................................................... 18
Level Translator Architecture.................................................... 15
Ordering Guide .......................................................................... 18
REVISION HISTORY
4/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
ADG3300
SPECIFICATIONS1
VCCY = 1.65 V to 5.5 V, VCCA = 1.15 V to VCCY, GND = 0 V. All specifications TMIN to TMAX, unless otherwise noted.
Table 1.
Parameter
LOGIC INPUTS/OUTPUTS
A Side
Input High Voltage3
Input Low Voltage3
Output High Voltage
Output Low Voltage
Three-State Pull-Down Resistance
Y Side
Input Low Voltage3
Input High Voltage3
Output High Voltage
Output Low Voltage
Capacitance3
Leakage Current
Enable (EN)
Input High Voltage3
Input Low Voltage3
Leakage Current
Capacitance3
Enable Time3
SWITCHING CHARACTERISTICS3
3.3 V ± 0.3 V ≤ VCCA ≤ VCCY, VCCY = 5 V ± 0.5 V
A Y Level Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
Y A Level Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
1.8 V ± 0.15 V ≤ VCCA ≤ VCCY, VCCY = 3.3 V ± 0.3 V
A Y Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
Symbol
Conditions
Min
VIHA
VIHA
VILA
VOHA
VOLA
RA,HiZ
VCCA = 1.15 V
VCCA = 1.2 V to 5.5 V
VCCA − 0.3
VCCA − 0.4
VY = VCCY, IOH = 20 µA, Figure 27
VY = 0 V, IOL = 20 µA, Figure 27
EN = 0
VCCA − 0.4
VIHY
VILY
VOHY
VOLY
CY
ILY, HiZ
VIHEN
VIHEN
VILEN
ILEN
CEN
tEN
Typ2
Max
0.4
4.2
6
0.4
8.4
VCCY − 0.4
0.4
VA = VCCA, IOH = 20 µA, Figure 28
VA = 0 V, IOL = 20 µA, Figure 28
f = 1 MHz, EN = 0, Figure 31
VY = 0 V/VCCY, EN = 0, Figure 29
VCCY − 0.4
VCCA = 1.15 V
VCCA = 1.2 V to 5.5 V
VCCA − 0.3
VCCA − 0.4
0.4
6
±1
0.4
±1
VEN = 0 V/VCCA, VA = 0 V, Figure 30
RS = RT = 50 Ω, VA = 0 V/VCCA (A Y),
Figure 32
Unit
V
V
V
V
V
kΩ
V
V
V
V
pF
µA
V
V
V
µA
pF
µs
3
1
1.8
6
2
2
10
3.5
3.5
2
4
3
ns
ns
ns
Mbps
ns
ns
4
1
7
3
ns
ns
3
7
2
3.5
2
ns
Mbps
ns
ns
8
2
2
11
5
5
2
4
4
RS = RT = 50 Ω, CL = 50 pF, Figure 33
tP, A-Y
tR, A-Y
tF, A-Y
DMAX, A-Y
tSKEW, A-Y
tPPSKEW, A-Y
50
RS = RT = 50 Ω, CL = 15 pF, Figure 34
tP, Y-A
tR, Y-A
tF, Y-A
DMAX, Y-A
tSKEW, Y-A
tPPSKEW, Y-A
50
RS = RT = 50 Ω, CL = 50 pF, Figure 33
tP, A-Y
tR, A-Y
tF, A-Y
DMAX, A-Y
tSKEW, A-Y
tPPSKEW, A-Y
50
Rev. 0 | Page 3 of 20
ns
ns
ns
Mbps
ns
ns
ADG3300
Parameter
Y A Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
1.15 V to 1.3 V ≤ VCCA ≤ VCCY, VCCY = 3.3 V ± 0.3 V
A Y Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
Y A Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
1.15 V to 1.3 V≤ VCCA ≤ VCCY, VCCY = 1.8 V ± 0.3 V
A Y Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
Y A Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
2.5 V ± 0.2 V ≤ VCCA ≤ VCCY, VCCY = 3.3 V ± 0.3 V
A Y Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
Y A Translation
Propagation Delay
Rise Time
Fall Time
Maximum Data Rate
Channel-to-Channel Skew
Part-to-Part Skew
Symbol
Conditions
RS = RT = 50 Ω, CL = 15 pF, Figure 34
tP, Y-A
tR, Y-A
tF, Y-A
DMAX, Y-A
tSKEW, Y-A
tPPSKEW, Y-A
Min
Typ2
Max
Unit
5
2
2
8
3.5
3.5
2
3
3
ns
ns
ns
Mbps
ns
ns
9
3
2
18
5
5
2
5
10
5
2
2
9
4
4
2
4
4
12
7
3
25
12
5
2
5
15
14
5
2.5
35
16
6.5
3
6.5
23.5
7
2.5
2
10
4
5
1.5
2
4
5
1
3
8
4
5
2
3
3
50
RS = RT = 50 Ω, CL = 50 pF, Figure 33
tP, A-Y
tR, A-Y
tF, A-Y
DMAX, A-Y
tSKEW, A-Y
tPPSKEW, A-Y
40
ns
ns
ns
Mbps
ns
ns
RS = RT = 50 Ω, CL = 15 pF, Figure 34
tP, Y-A
tR, Y-A
tF, Y-A
DMAX, Y-A
tSKEW, Y-A
tPPSKEW, Y-A
40
ns
ns
ns
Mbps
ns
ns
RS = RT = 50 Ω, CL = 50 pF, Figure 33
tP, A-Y
tR, A-Y
tF, A-Y
DMAX, A-Y
tSKEW, A-Y
tPPSKEW, A-Y
25
ns
ns
ns
Mbps
ns
ns
RS = RT = 50 Ω, CL = 15 pF, Figure 34
tP, Y-A
tR, Y-A
tF, Y-A
DMAX, Y-A
tSKEW, Y-A
tPPSKEW, Y-A
25
ns
ns
ns
Mbps
ns
ns
RS = RT = 50 Ω, CL = 50 pF, Figure 33
tP, A-Y
tR, A-Y
tF, A-Y
DMAX, A-Y
tSKEW, A-Y
tPPSKEW, A-Y
60
ns
ns
ns
Mbps
ns
ns
RS = RT = 50 Ω, CL = 15 pF, Figure 34
tP, Y-A
tR, Y-A
tF, Y-A
DMAX, Y-A
tSKEW, Y-A
tPPSKEW, Y-A
60
Rev. 0 | Page 4 of 20
ns
ns
ns
Mbps
ns
ns
ADG3300
Parameter
POWER REQUIREMENTS
Power Supply Voltages
Quiescent Power Supply Current
Symbol
Conditions
Min
VCCA
VCCY
ICCA
VCCA ≤ VCCY
1.15
1.65
ICCY
Three-State Mode Power Supply Current
IHiZA
IHiZY
VA = 0 V/VCCA, VY = 0 V/VCCY,
VCCA = VCCY = 5.5 V, EN = 1
VA = 0 V/VCCA, VY = 0 V/VCCY,
VCCA = VCCY = 5.5 V, EN = 1
VCCA = VCCY = 5.5 V, EN = 0
VCCA = VCCY = 5.5 V, EN = 0
1
Temperature range is a follows: B version: −40°C to +85°C.
All typical values are at TA = 25°C, unless otherwise noted.
3
Guaranteed by design; not subject to production test.
2
Rev. 0 | Page 5 of 20
Typ2
Max
Unit
0.17
5.5
5.5
5
V
V
µA
0.27
5
µA
0.1
0.1
5
5
µA
µA
ADG3300
ABSOLUTE MAXIMUM RATINGS
TA = 25°C, unless otherwise noted.
Table 2.
Parameter
VCCA to GND
VCCY to GND
Digtal Inputs (A)
Digtal Inputs (Y)
EN to GND
Operating Temperature Range
Industrial (B Version)
Storage Temperature Range
Junction Temperature
θJA Thermal Impedance (4-Layer Board)
20-Lead TSSOP
Lead Temperature, Soldering (10 sec)
IR Reflow, Peak Temperature (<20 sec)
Rating
−0.3 V to +7 V
VCCA to +7 V
−0.3 V to (VCCA + 0.3 V)
−0.3 V to (VCCY + 0.3 V)
−0.3 V to +7 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those listed in the operational sections
of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability. Only one absolute maximum rating may be
applied at any one time.
−40°C to +85°C
−65°C to +150°C
150°C
78°C/W
300°C
260°C
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the
human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 6 of 20
ADG3300
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
A1
1
20 Y1
VCCA
2
19 VCCY
A2
3
A3
4
A4
5
A5
6
15 Y5
A6
TOP VIEW
(Not to Scale)
18 Y2
17 Y3
16 Y4
7
14 Y6
A7 8
13 Y7
9
12 Y8
A8
EN 10
11 GND
05061-002
ADG3300
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Mnemonic
A1
VCCA
A2
A3
A4
A5
A6
A7
A8
EN
GND
Y8
Y7
Y6
Y5
Y4
Y3
Y2
VCCY
Y1
Description
Input/Output A1. Referenced to VCCA.
Power Supply Voltage Input for the A1 to A8 I/O pins (1.15 V ≤ VCCA < VCCY).
Input/Output A2. Referenced to VCCA.
Input/Output A3. Referenced to VCCA.
Input/Output A4. Referenced to VCCA.
Input/Output A5. Referenced to VCCA.
Input/Output A6. Referenced to VCCA.
Input/Output A7. Referenced to VCCA.
Input/Output A8. Referenced to VCCA.
Active High Enable Input.
Ground.
Input/Output Y8. Referenced to VCCY.
Input/Output Y7. Referenced to VCCY.
Input/Output Y6. Referenced to VCCY.
Input/Output Y5. Referenced to VCCY.
Input/Output Y4. Referenced to VCCY.
Input/Output Y3. Referenced to VCCY.
Input/Output Y2. Referenced to VCCY.
Power Supply Voltage Input for the Y1 to Y8 I/O pins (1.65 V ≤ VCCY ≤ 5.5 V).
Input/Output Y1. Referenced to VCCY.
Rev. 0 | Page 7 of 20
ADG3300
TYPICAL PERFORMANCE CHARACTERISTICS
3.0
1.0
TA = 25°C
1 CHANNEL
0.9
CL = 50pF
TA = 25°C
1 CHANNEL
CL = 15pF
2.5
0.8
VCCA = 3.3V, VCCY = 5V
2.0
ICCY (mA)
0.6
0.5
VCCA = 3.3V, VCCY = 5V
1.5
0.4
1.0
VCCA = 1.8V, VCCY = 3.3V
0.3
VCCA = 1.8V, VCCY = 3.3V
0.2
0.5
0.1
VCCA = 1.2V, VCCY = 1.8V
VCCA = 1.2V, VCCY = 1.8V
0
5
10
15
20
25
30
35
DATA RATE (Mbps)
40
45
50
0
05061-003
0
0
5
10
15
20
25
30
35
40
45
50
DATA RATE (Mbps)
05061-006
ICCA (mA)
0.7
Figure 6. ICCY vs. Data Rate (Y A Level Translation)
Figure 3. ICCA vs. Data Rate (A Y Level Translation)
1.6
10
TA = 25°C
1 CHANNEL
9
CL = 50pF
TA = 25°C
1 CHANNEL
VCCA = 1.2V
VCCY = 1.8V
1.4
8
20Mbps
1.2
7
ICCY (mA)
ICCY (mA)
VCCA = 3.3V, VCCY = 5V
6
5
4
1.0
0.8
10Mbps
0.6
VCCA = 1.8V, VCCY = 3.3V
3
0.4
5Mbps
2
VCCA = 1.2V, VCCY = 1.8V
1
0
5
10
15
20
25
30
35
DATA RATE (Mbps)
40
45
50
53
63
73
TA = 25°C
1 CHANNEL
VCCA = 1.2V
VCCY =1.8V
0.9
0.8
0.7
ICCA (mA)
2.0
1.5
1.0
0.6
20Mbps
0.5
0.4
0.3
VCCA = 1.8V, VCCY = 3.3V
10Mbps
5Mbps
0.2
VCCA = 1.2V, VCCY = 1.8V
5
10
15
20
25
30
35
40
45
DATA RATE (Mbps)
50
1Mbps
0
05061-005
0
0.1
13
23
33
43
CAPACITIVE LOAD (pF)
53
Figure 8. ICCA vs. Capacitive Load at Pin A for Y A (1.8 V 1.2 V)
Level Translation
Figure 5. ICCA vs. Data Rate (Y A Level Translation)
Rev. 0 | Page 8 of 20
05061-008
0.5
0
43
1.0
VCCA = 3.3V, VCCY = 5V
ICCA (mA)
33
Figure 7. ICCY vs. Capacitive Load at Pin Y for A Y (1.2 V 1.8 V)
Level Translation
TA = 25°C
1 CHANNEL
CL = 15pF
2.5
23
CAPACITIVE LOAD (pF)
Figure 4. ICCY vs. Data Rate (A Y Level Translation)
3.0
13
05061-007
1Mbps
0
05061-004
0
0.2
ADG3300
9
7
TA = 25°C
1 CHANNEL
VCCA = 1.8V
VCCY = 3.3V
8
7
TA = 25°C
1 CHANNEL
6 VCCA = 3.3V
VCCY = 5V
50Mbps
50Mbps
5
ICCA (mA)
ICCY (mA)
6
5
30Mbps
4
4
30Mbps
3
20Mbps
3
20Mbps
2
2
10Mbps
10Mbps
1
1
33
43
53
CAPACITIVE LOAD (pF)
63
0
13
05061-009
23
73
53
10
TA = 25°C
9 1 CHANNEL
DATA RATE = 50kbps
8
TA = 25°C
1 CHANNEL
VCCA = 1.8V
VCCY = 3.3V
3.5
VCCA = 1.2V, VCCY = 1.8V
7
50Mbps
3.0
RISE TIME (ns)
ICCA (mA)
43
Figure 12. ICCA vs. Capacitive Load at Pin A for Y A (5 V 3.3 V)
Level Translation
5.0
4.0
33
CAPACITIVE LOAD (pF)
Figure 9. ICCY vs. Capacitive Load at Pin Y for A Y (1.8 V 3.3 V)
Level Translation
4.5
23
05061-012
5Mbps
5Mbps
0
13
2.5
2.0
30Mbps
1.5
6
5
4
VCCA = 1.8V, VCCY = 3.3V
3
20Mbps
1.0
2
VCCA = 3.3V, VCCY = 5V
10Mbps
0.5
5Mbps
23
33
43
CAPACITIVE LOAD (pF)
53
0
13
05061-010
0
13
Figure 10. ICCA vs. Capacitive Load at Pin A for Y A (3.3 V 1.8 V)
Level Translation
23
33
43
53
CAPACITIVE LOAD (pF)
63
73
05061-013
1
Figure 13. Rise Time vs. Capacitive Load at Pin Y (A Y Level Translation)
12
4.0
TA = 25°C
1 CHANNEL
VCCA = 3.3V
10 V
CCY = 5V
TA = 25°C
1 CHANNEL
3.5 DATA RATE = 50kbps
50Mbps
VCCA = 1.2V, VCCY = 1.8V
3.0
FALL TIME (ns)
30Mbps
6
20Mbps
4
2.5
VCCA = 1.8V, VCCY = 3.3V
2.0
1.5
VCCA = 3.3V, VCCY = 5V
1.0
10Mbps
2
0.5
0
13
23
33
43
53
63
73
CAPACITIVE LOAD (pF)
Figure 11. ICCY vs. Capacitive Load at Pin Y for A Y (3.3 V 5 V)
Level Translation
0
13
23
33
43
53
CAPACITIVE LOAD (pF)
63
73
05061-014
5Mbps
05061-011
ICCY (mA)
8
Figure 14. Fall Time vs. Capacitive Load at Pin Y (A Y Level Translation)
Rev. 0 | Page 9 of 20
ADG3300
12
10
TA = 25°C
9 1 CHANNEL
DATA RATE = 50kbps
8
VCCA = 1.2V, VCCY = 1.8V
6
5
4
VCCA = 1.8V, VCCY = 3.3V
3
2
8
6
VCCA = 1.8V, VCCY = 3.3V
4
2
1
VCCA = 3.3V, VCCY = 5V
23
28
33
38
43
48
53
CAPACITIVE LOAD (pF)
0
13
05061-015
18
33
43
53
63
73
CAPACITIVE LOAD (pF)
Figure 18. Propagation Delay (tPHL) vs.
Capacitive Load at Pin Y (A Y Level Translation)
Figure 15. Rise Time vs. Capacitive Load at Pin A (Y A Level Translation)
9
TA = 25°C
1 CHANNEL
DATA RATE = 50kbps
8
PROPAGATION DELAY (ns)
3.0
2.5
VCCA = 1.2V, VCCY = 1.8V
2.0
VCCA = 1.8V, VCCY = 3.3V
1.5
VCCA = 3.3V, VCCY = 5V
1.0
0.5
TA = 25°C
1 CHANNEL
DATA RATE = 50kbps
7
VCCA = 1.2V, VCCY = 1.8V
6
5
4
3
VCCA = 1.8V, VCCY = 3.3V
2
VCCA = 3.3V, VCCY = 5V
1
13
18
23
28
33
38
43
CAPACITIVE LOAD (pF)
48
53
0
13
05061-016
0
23
28
33
38
43
48
53
CAPACITIVE LOAD (pF)
Figure 19. Propagation Delay (tPLH) vs.
Capacitive Load at Pin A (Y A Level Translation)
Figure 16. Fall Time vs. Capacitive Load at Pin A (Y A Level Translation)
9
14
TA = 25°C
1 CHANNEL
8 DATA RATE = 50kbps
TA = 25°C
1 CHANNEL
12 DATA RATE = 50kbps
PROPAGATION DELAY (ns)
VCCA = 1.2V, VCCY = 1.8V
10
8
6
VCCA = 1.8V, VCCY = 3.3V
4
VCCA = 3.3V, VCCY = 5V
2
VCCA = 1.2V, VCCY = 1.8V
7
6
5
4
VCCA = 1.8V, VCCY = 3.3V
3
VCCA = 3.3V, VCCY = 5V
2
1
23
33
43
53
CAPACITIVE LOAD (pF)
63
73
0
05061-017
0
13
18
13
18
23
28
33
38
43
CAPACITIVE LOAD (pF)
48
Figure 20. Propagation Delay(tPHL) vs.
Capacitive Load at Pin A (Y A Level Translation)
Figure 17. Propagation Delay (tPLH) vs.
Capacitive Load at Pin Y (A Y Level Translation)
Rev. 0 | Page 10 of 20
53
05061-020
3.5
05061-019
4.0
FALL TIME (ns)
23
05061-018
VCCA = 3.3V, VCCY = 5V
0
13
PROPAGATION DELAY (ns)
VCCA = 1.2V, VCCY = 1.8V
10
PROPAGATION DELAY (ns)
RISE TIME (ns)
7
DATA RATE = 50kbps
TA = 25°C
1 CHANNEL
ADG3300
Figure 21. Eye Diagram at Y Output (1.2 V to 1.8 V Level Translation, 25 Mbps)
Figure 24. Eye Diagram at A Output (3.3 V to 1.8 V Level Translation, 50 Mbps)
TA = 25°C
DATA RATE = 25Mbps
CL = 50pF
1 CHANNEL
TA = 25°C
DATA RATE = 50Mbps
CL = 50pF
1 CHANNEL
05061-022
400mV/DIV
5ns/DIV
1V/DIV
Figure 22. Eye Diagram at A Output (1.8 V to 1.2 V Level Translation, 25 Mbps)
500mV/DIV
3ns/DIV
3ns/DIV
Figure 25. Eye Diagram at Y Output (3.3 V to 5 V Level Translation, 50 Mbps)
TA = 25°C
DATA RATE = 50Mbps
CL = 15pF
1 CHANNEL
CL = 50pF
1 CHANNEL
05061-023
TA = 25°C
DATA RATE = 50Mbps
3ns/DIV
05061-024
400mV/DIV
05061-025
5ns/DIV
TA = 25°C
DATA RATE = 50Mbps
CL = 15pF
1 CHANNEL
800mV/DIV
Figure 23. Eye Diagram at Y Output (1.8 V to 3.3 V Level Translation, 50 Mbps)
3ns/DIV
05061-026
200mV/DIV
CL = 50pF
1 CHANNEL
05061-021
TA = 25°C
DATA RATE = 25Mbps
Figure 26. Eye Diagram at A Output (5 V to 3.3 V Level Translation, 50 Mbps)
Rev. 0 | Page 11 of 20
ADG3300
TEST CIRCUITS
EN
VCCA
ADG3300
VCCY
0.1µF
0.1µF
ADG3300
VCCA
A
VCCY
0.1µF
Y
0.1µF
K2
K1
A
GND
Figure 27. VOH/VOL Voltages at Pin A
EN
VCCA
ADG3300
K2
Figure 30. EN Pin Leakage Current
EN
VCCA
VCCY
0.1µF
EN
K
05061-031
05061-027
IOL
ADG3300
VCCY
0.1µF
Y
A
A
Y
K1
GND
GND
IOH
05061-028
IOL
Figure 28. VOH/VOL Voltages at Pin Y
EN
VCCA
ADG3300
VCCY
0.1µF
0.1µF
Y
K
A
GND
05061-030
A
Figure 29. Three-State Leakage Current at Pin Y
Rev. 0 | Page 12 of 20
Figure 31.Capacitance at Pin Y
CAPACITANCE
METER
05061-033
IOH
Y
A
GND
ADG3300
VCCA
0.1µF
VCCY
ADG3300
+
10µF
+
10µF
0.1µF
1MΩ
A
VA
K1
Y
VY
K2
50pF
1MΩ
SIGNAL SOURCE
EN
Z0 = 50Ω
RS
GND
VEN
50Ω
RT
50Ω
VCCA
tEN1
VEN
0V
VCCA
VA
0V
VCCY
90%
VY
0V
VCCA
tEN2
VEN
0V
VA
VCCA
0V
VCCY
VY
10%
05061-034
0V
NOTES
1. tEN IS WHICHEVER IS LARGER BETWEEN tEN1 AND tEN2.
Figure 32. Enable Time
EN
VCCY
ADG3300
VCCA
SIGNAL
SOURCE
0.1µF
Z0 = 50Ω V
A
RS
50Ω
EN
+
10µF
0.1µF
+
10µF
A
Y
VY
VA
50pF
VCCY
+
10µF
0.1µF
+
10µF
0.1µF
RT
50Ω
ADG3300
VCCA
SIGNAL
SOURCE
A
Y
Z0 = 50Ω
RS
50Ω
RT
50Ω
15pF
GND
VY
GND
VA
VY
50%
50%
VA
tP,Y-A
tP,Y-A
90%
50%
10%
tR,A-Y
05061-035
tF,A-Y
tF,Y-A
tR,Y-A
Figure 34. Switching Characteristics (Y A Level Translation)
Figure 33. Switching Characteristics (A Y Level Translation)
Rev. 0 | Page 13 of 20
05061-036
tP,A-Y
tP,A-Y
VY
90%
50%
10%
ADG3300
TERMINOLOGY
Table 4.
Symbol
VIHA
VILA
VOHA
VOLA
RA,HiZ
VIHY
VILY
VOHY
VOLY
CY
ILY, HiZ
VIHEN
VILEN
CEN
ILEN
tEN
tP, A-Y
tR, A-Y
tF, A-Y
DMAX, A-Y
tSKEW, A-Y
tPPSKEW, A-Y
tP, Y-A
tR, Y-A
tF, Y-A
DMAX, Y-A
tSKEW, Y-A
tPPSKEW, Y-A
VCCA
VCCY
ICCA
ICCY
IHiZA
IHiZY
Description
Logic input high voltage at Pins A1 to A8.
Logic input low voltage at Pins A1 to A8.
Logic output high voltage at Pins A1 to A8.
Logic output low voltage at Pins A1 to A8.
Pull-down resistance measured at Pins A1 to A8 when EN = 0.
Logic input high voltage at Pins Y1 to Y8.
Logic input low voltage at Pins Y1 to Y8.
Logic output high voltage at Pins Y1 to Y8.
Logic output low voltage at Pins Y1 to Y8.
Capacitance measured at Pins Y1 to Y8 (EN = 0).
Leakage current at Pins Y1 to Y8 when EN = 0 (high impedance state at Pins Y1 to Y8).
Logic input high voltage at the EN pin.
Logic input low voltage at the EN pin.
Capacitance measured at EN pin.
Enable (EN) pin leakage curent.
Three-state enable time for Pins Y1 to Y8.
Propagation delay when translating logic levels in the A Y direction.
Rise time when translating logic levels in the A Y direction.
Fall time when translating logic levels in the A Y direction.
Guaranteed data rate when translating logic levels in the A Y direction under the driving and loading conditions
specified in Table 1.
Difference between propagation delays on any two channels when translating logic levels in the A Y direction.
Difference in propagation delay between any one channel and the same channel on a different part (under the
same driving/loading conditions) when translating logic levels in the A Y direction.
Propagation delay when translating logic levels in the Y A direction.
Rise time when translating logic levels in the Y A direction.
Fall time when translating logic levels in the Y A direction.
Guaranteed data rate when translating logic levels in the Y A direction under the driving and loading conditions
specified in Table 1.
Difference between propagation delays on any two channels when translating logic levels in the Y A direction.
Difference in propagation delay between any one channel and the same channel on a different part (under the
same driving/loading conditions) when translating in the Y A direction.
VCCA supply voltage.
VCCY supply voltage.
VCCA supply current.
VCCY supply current.
VCCA supply current during three-state mode (EN = 0).
VCCY supply current during three-state mode (EN = 0).
Rev. 0 | Page 14 of 20
ADG3300
THEORY OF OPERATION
The ADG3300 level translator allows the level shifting necessary
for data transfer in a system where multiple supply voltages are
used. The device requires two supplies, VCCA and VCCY (VCCA ≤
VCCY). These supplies set the logic levels on each side of the
device. When driving the A pins, the device translates the VCCAcompatible logic levels to VCCY-compatible logic levels available
at the Y pins. Similarly, since the device is capable of bidirectional
translation, when driving the Y pins, the VCCY-compatible logic
levels are translated to VCCA-compatible logic levels available at
the A pins. When EN = 0, the A1 to A8 are internally pulled
down with 6 kΩ resistors while Y1 to Y8 pins are three-stated.
When EN is driven high, the ADG3300 goes into normal
operation mode and performs level translation.
INPUT DRIVING REQUIREMENTS
To ensure correct operation of the ADG3300, the circuit that
drives the input of an ADG3300 channels should have an output
impedance of less than or equal to 150 Ω and a minimum
current driving capability of 36 mA.
OUTPUT LOAD REQUIREMENTS
The ADG3300 level translator is designed to drive CMOScompatible loads. If current driving capability is required, it is
recommended to use buffers between the ADG3300 outputs
and the load.
ENABLE OPERATION
The ADG3300 provides three-state operation at the Y I/O pins
by using the enable (EN) pin as shown in Table 5.
LEVEL TRANSLATOR ARCHITECTURE
The ADG3300 consists of eight bidirectional channels. Each
channel can translate logic levels in either the A Y or the Y A
direction. It uses a one-shot accelerator architecture, which
ensures excellent switching characteristics. Figure 35 shows a
simplified block diagram of a bidirectional channel.
Table 5. Truth Table
EN
0
1
1
VCCA
VCCY
T1
2
T2
P
A
U2
ONE-SHOT GENERATOR
Y
N
A I/O Pins
6 kΩ pull-down to GND
Normal operation2
High impedance state.
In normal operation, the ADG3300 performs level translation.
When EN = 0, the ADG3300 enters into three-state mode. In
this mode the current consumption from both the VCCA and
VCCY supplies is reduced, allowing the user to save power, which
is critical, especially for battery-operated systems. The EN input
pin can be driven with either VCCA- or VCCY-compatible logic
levels.
6kΩ
U1
Y I/O Pins
Hi-Z1
Normal operation2
POWER SUPPLIES
T4
U4
U3
T3
05061-037
6kΩ
Figure 35. Simplified Block Diagram of an ADG3300 Channel
The logic level translation in the A Y direction is performed
using a level translator (U1) and an inverter (U2), and the
translation in the Y A direction is performed using the inverters
U3 and U4. The one-shot generator detects a rising or falling
edge present on either the A side or the Y side of the channel. It
sends a short pulse that turns on the PMOS transistors (T1–T2)
for a rising edge, or the NMOS transistors (T3–T4) for a falling
edge. This charges/discharges the capacitive load faster, which
results in fast rise and fall times.
For proper operation of the ADG3300, the voltage applied to
the VCCA must always be less than or equal to the voltage applied
to VCCY. To meet this condition, the recommended power-up
sequence is VCCY first and then VCCA. The ADG3300 operates
properly only after both supply voltages reach their nominal
values. It is not recommended to use the part in a system where
VCCA might be greater than VCCY during power-up due to a significant increase in the current taken from the VCCA supply. For
optimum performance, the VCCA and VCCY pins should be
decoupled to GND as close as possible to the device.
The inputs of the unused channels (A or Y) should be tied to
their corresponding VCC rail (VCCA or VCCY) or to GND.
Rev. 0 | Page 15 of 20
ADG3300
DATA RATE
The maximum data rate at which the device is guaranteed
to operate is a function of the VCCA and VCCY supply voltage
combination and the load capacitance. It is given by the
maximum frequency of a square wave that can be applied to
the device, which meets the VOH and VOL levels at the output and
does not exceed the maximum junction temperature (see
Table 2). Table 6 shows the guaranteed data rates at which the
ADG3300 can operate in both directions (A Y and Y A level
translation) for various VCCA and VCCY supply combinations.
Table 6. Guaranteed Data Rate (Mbps)1
VCCY
VCCA
1.2 V (1.15 V to 1.3 V)
1.8 V (1.65 V to 1.95 V)
2.5 V (2.3 V to 2.7 V)
3.3 V (3.0 V to 3.6 V)
5 V (4.5 V to 5.5 V)
1
1.8 V
(1.65 V to 1.95 V)
25
-
2.5 V
(2.3 V to 2.7 V)
30
45
-
3.3 V
(3.0 V to 3.6 V)
40
50
60
-
The load capacitance used is 50 pF when translating in the A Y direction and 15 pF when translating in the Y A direction.
Rev. 0 | Page 16 of 20
5V
(4.5 V to 5.5 V)
40
50
50
50
-
ADG3300
APPLICATIONS
other devices without causing contention issues. Figure 37 shows
an application where a 3.3 V microprocessor is connected to
1.8 V peripheral devices using the three-state feature.
100nF
I/OH1
3.3V
1.8V
I/OL1
VCCY
I/OH2
Y2
I/OH3
Y3
MICROPROCESSOR/ I/OH4
MICROCONTROLLER/
I/OH5
DSP
I/OH6
Y4
I/OH7
I/OH8
GND
CS
Y1
VCCA
I/OH1
A2
Y2
I/OH2
I/OL3
A3
Y3
I/OH3
MICROPROCESSOR/ I/OL4
MICROCONTROLLER/
DSP
I/OL5
A4
I/OH4
A5
Y5
I/OH5
I/OL6
A6
Y6
I/OH6
I/OL7
A7
Y7
I/OH7
I/OL8
A8
Y8
I/OH8
EN
GND
GND
1.8V
I/OL 2
A3
I/OL 3
A4
I/OL 4
A5
I/OL 5
Y6
A6
I/OL 6
Y7
A7
I/OL 7
Y8
A8
I/OL 8
GND
EN
GND
PERIPHERAL
DEVICE 1
100nF
A1
I/OL 1
A2
I/OL 2
A3
I/OL 3
A4
I/OL 4
Y5
A5
I/OL 5
Y6
A6
I/OL 6
Y7
A7
I/OL 7
Y8
A8
I/OL 8
GND
EN
GND
Y2
Y3
Y4
1.8V
VCCA
ADG3300
PERIPHERAL
DEVICE 2
Figure 37. 1.8 V to 3.3 V Level Translation Circuit
Using the Three-State Feature
LAYOUT GUIDELINES
PERIPHERAL
DEVICE
05061-038
GND
Y4
ADG3300
A2
Y5
Y1
VCCY
I/OL2
ADG3300
VCCY
3.3V
I/OL1
VCCA
100nF
100nF
A1
A1
Y1
Figure 36 shows an application where a 1.8 V microprocessor
can read or write data to or from a 3.3 V peripheral device using
an 8-bit bus.
100nF
100nF
05061-039
The ADG3300 is designed for digital circuits that operate at
different supply voltages; therefore, logic level translation is
required. The lower voltage logic signals are connected to the
A pins, and the higher voltage logic signals are connected to the
Y pins. The ADG3300 can provide level translation in both
directions from A Y and Y A on all eight channels, eliminating
the need for a level translator IC for each direction. The internal
architecture allows the ADG3300 to perform bidirectional level
translation without an additional signal to set the direction of
the translation. It also allows simultaneous data flow in both
directions on the same part, for example, four channels translate
in the A Y direction while the other four translate in the Y A
direction. This simplifies the design by eliminating the timing
requirements for the direction signal and reduces the number of
ICs used for level translation.
Figure 36. 1.8 V to 3.3 V 8-Bit Level Translation Circuit
When the application requires level translation between a
microprocessor and multiple peripheral devices, the ADG3300
Y I/O pins (Y1 to Y8) can be three-stated by setting EN = 0.
This feature allows the ADG3300 to share the data buses with
As with any high speed digital IC, the printed circuit board
layout is important in the overall circuit performance. Care
should be taken to ensure proper power supply bypass and
return paths for the high speed signals. Each VCC pin (VCCA and
VCCY) should be bypassed using low effective series resistance
(ESR) and effective series inductance (ESI) capacitors placed as
close as possible to the VCCA and VCCY pins. The parasitic inductance of the high speed signal track might cause significant
overshoot. This effect can be reduced by keeping the length
of the tracks as short as possible. A solid copper plane for the
return path (GND) is also recommended.
Rev. 0 | Page 17 of 20
ADG3300
OUTLINE DIMENSIONS
6.60
6.50
6.40
20
11
4.50
4.40
4.30
6.40 BSC
1
10
PIN 1
0.65
BSC
1.20 MAX
0.15
0.05
COPLANARITY
0.10
0.30
0.19
0.20
0.09
SEATING
PLANE
8°
0°
0.75
0.60
0.45
COMPLIANT TO JEDEC STANDARDS MO-153AC
Figure 38 . 20-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-20)
Dimensions shown in millimeters
ORDERING GUIDE
Model
ADG3300BRUZ1
ADG3300BRUZ-REEL1
ADG3300BRUZ-REEL71
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
TSSOP
TSSOP
TSSOP
Z = Pb-free part.
Rev. 0 | Page 18 of 20
Package Option
RU-20
RU-20
RU-20
ADG3300
NOTES
Rev. 0 | Page 19 of 20
ADG3300
NOTES
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05061–0–4/05(0)
Rev. 0 | Page 20 of 20