MD200xE Datasheet - Micropower Direct

MD200xE Series
Low Cost, 2W
Miniature SIP
DC/DC Converters
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Key Features:
• 2W Output Power
• Miniature SIP Case
• Short Circuit Protected
• 1,500 VDC Isolation
Input
Parameter
Conditions
Min.
5 VDC Input 4.50
12 VDC Input 10.80
15 VDC Input 13.50
24 VDC Input 21.60
Internal Capacitor
Input Voltage Range
Input Filter
• Single and Dual Outputs
Output
• >3.5 MHour MTBF
Parameter
Output Voltage Accuracy
3.3 VDC Output
Line Regulation
All Other Outputs
Load Regulation, See Note 1
• -40°C to +105°C Operation
• LOW COST
3.0 kV Isolation
Models
Available
Ripple & Noise (20 MHz), See Note 2
Conditions
Min.
Typ.
5.0
12.0
15.0
24.0
Max.
5.50
13.20
16.50
26.40
Units
Typ.
±2.5
Max.
Units
%
±1.5
±1.2
For VIN Change of 1%
See Model Selection Guide
Output Voltage <12 VDC
60
15 VDC, 24 VDC Output
75
Temperature Coefficient
Output Short Circuit
VDC
%
mV P - P
±0.03
%/°C
Typ.
Max.
20
100
300
Units
VDC
M
pF
kHz
Continuous (Autorecovery)
General
Parameter
Isolation Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency
EMI Characteristics
Parameter
Conditions
60 Seconds
500 VDC
100 kHz, 1V
Conditions
EMC Compliance, Single Output
EMC Compliance, Dual Output
Min.
Conducted
Radiated
EMI Compliance, See Note 4
Min.
1,500
1,000
Electrostatic Discharge (ESD)
Typ.
Max.
Units
CISPR22/EN 55022 Level B
CISPR22/EN 55022 Level B
EN 61000-4-2 Level B Contact ±8 kV
EN 61000-4-2 Level B Contact ±6 kV
Environmental
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: [email protected]
W: www.micropowerdirect.com
Parameter
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight
Conditions
Min.
Typ.
-40
+25
-55
Free Air Convection
RH, Non-condensing
Ambient
Max.
+105
+125
Units
°C
°C
95
%
0.772 x 0.276 x 0.394 Inches (19.6 x 7.0 x 10.0 mm)
Non-Conductive Black Plastic (UL-94V0)
0.08 Oz (2.4g)
Reliability Specifications
Parameter
MTBF
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min.
3.5
Typ.
Max.
Units
MHours
Min.
-0.7
-0.7
-0.7
-0.7
Typ.
Max.
9.0
18.0
21.0
30.0
300
Units
Absolute Maximum Ratings
Parameter
Conditions
Input Voltage Surge (1 Sec)
Lead Temperature
5 VDC Input
12 VDC Input
15 VDC Input
24 VDC Input
1.5 mm From Case For 10 Sec
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
VDC
°C
www.micropowerdirect.com
Model Selection Guide
Model
Number
MD205S-03E
MD205S-05E
MD205S-12E
MD205S-15E
MD205S-24E
MD205D-03E
MD205D-05E
MD205D-12E
MD205D-15E
MD205D-24E
MD212S-03E
MD212S-05E
MD212S-12E
MD212S-15E
MD212D-03E
MD212D-05E
MD212D-12E
MD212D-15E
MD215D-15E
MD224S-03E
MD224S-05E
MD224S-12E
MD224S-15E
MD224S-24E
MD224D-03E
MD224D-05E
MD224D-12E
MD224D-15E
Input
Voltage (VDC)
Current (mA)
Nominal
Range
Full-Load No-Load
5
4.5 - 5.5
476
25
5
4.5 - 5.5
450
25
5
4.5 - 5.5
476
25
5
4.5 - 5.5
476
25
5
4.5 - 5.5
476
25
5
4.5 - 5.5
540
25
5
4.5 - 5.5
500
25
5
4.5 - 5.5
476
25
5
4.5 - 5.5
476
25
5
4.5 - 5.5
476
25
12
10.8 - 13.2
198
15
12
10.8 - 13.2
198
15
12
10.8 - 13.2
198
15
12
10.8 - 13.2
198
15
12
10.8 - 13.2
208
15
12
10.8 - 13.2
198
15
12
10.8 - 13.2
196
15
12
10.8 - 13.2
198
15
15
13.5 - 16.5
157
10
24
21.6 - 26.4
99
8
24
21.6 - 26.4
99
8
24
21.6 - 26.4
99
8
24
21.6 - 26.4
99
8
24
21.6 - 26.4
98
8
24
21.6 - 26.4
104
8
24
21.6 - 26.4
99
8
24
21.6 - 26.4
99
8
24
21.6 - 26.4
99
8
Voltage
Output
Current
(VDC)
(mA, Max)
3.3
5.0
12.0
15.0
24.0
±3.3
±5.0
±12.0
±15.0
±24.0
3.3
5.0
12.0
15.0
±3.3
±5.0
±12.0
±15.0
±15.0
3.3
5.0
12.0
15.0
24.0
±3.3
±5.0
±12.0
±15.0
400
400
167
133
83
±303
±200
±83
±67
±42
400
400
167
133
±303
±200
±83
±67
±67
400
400
167
133
83
±303
±200
±83
±67
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
2. When measuring output ripple, it is recommended that an external 1 µF ceramic capacitor & 10 µF electrolytic
capacitor be placed in parallel from the +Vout pin to the -Vout pin for single output models, or from each output
to common for dual output models.
3. Operation at no load will not damage these units, however, they may not meet all specifications.
4. These converters are specified for operation without external components. However, in some applications the
addition of input/output capacitors will enhance stability and reduce output ripple. The simple connection shown
below will typically meet EN 55022 Class B. For dual output units, a capacitor should be connected from each
output to common.
VIN
C1
L1
VOUT
C2
5 VDC
12 VDC
15 VDC
24 VDC
4.7 µF/50V
4.7 µF/50V
4.7 µF/50V
4.7 µF/50V
6.8 µH
6.8 µH
6.8 µH
6.8 µH
3.3 VDC
5 VDC
12 VDC
15 VDC
24 VDC
±3.3 VDC
±5 VDC
±12 VDC
±15 VDC
±24 VDC
10 µF
10 µF
2.2 µF
1.0 µF
1.0 µF
4.7 µF
4.7 µF
1.0 µF
0.47 µF
0.47 µF
Output
Load
Rating
Efficiency Fuse
Regulation Capacitive
Slow-Blow
Load
(%, Typ)
(mA)
(mA, Min)
(µF Max)
% Typ.
40.0
18.0
220
84
1,000
40.0
12.0
220
89
1,000
17.0
8.0
220
84
1,000
13.0
7.0
220
84
1,000
8.0
6.0
220
84
1,000
±30.0
18.0
100
74
1,000
±20.0
12.0
100
80
1,000
±8.0
8.0
100
84
1,000
±7.0
7.0
100
84
1,000
±4.0
6.0
100
84
1,000
40.0
18.0
220
84
500
40.0
12.0
220
84
500
17.0
8.0
220
84
500
13.0
7.0
220
84
500
±30.0
18.0
100
80
500
±20.0
12.0
100
84
500
±8.0
8.0
100
85
500
±7.0
7.0
100
84
500
±7.0
7.0
100
85
500
40.0
18.0
220
84
250
40.0
12.0
220
84
250
17.0
8.0
220
84
250
13.0
7.0
220
84
250
8.0
6.0
220
85
250
±30.0
18.0
100
80
250
±20.0
12.0
100
84
250
±8.0
8.0
100
84
250
±7.0
7.0
100
84
250
Current
Derating Curve
Mechanical Dimensions
5. It is recommended that a fuse be used on the input of a power supply for
protection. See the Model Selection table above for the correct rating.
Pin Connections
Pin
Single
Dual
Pin
Single
Dual
1
+VIN
+VIN
5
No Pin
Common
6
+VOUT
+VOUT
2
-VIN
-VIN
4
-VOUT
-VOUT
MicroPower Direct
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072
•
TEL: (781) 344-8226
•
Notes:
• All dimensions are typical in inches (mm)
• Tolerance x.xx = ±0.02 (±0.50)
• Pin 1 is marked by a “dot” or indentation on the unit
FAX: (781) 344-8481
•
E-Mail: [email protected]