2 - Magnetrol International

Eclipse® Model 707
Guided Wave Radar
Level Transmitter for
Interface Measurement
D E S C R I P T I O N
A P P L I C A T I O N S
The Eclipse Model 707 Interface Transmitter is a 24 VDC
loop-powered liquid level transmitter based upon the
revolutionary Guided Wave Radar (GWR) technology.
UPPER MEDIA: Liquids having a dielectric
constant of 1.4–5
This leading-edge transmitter is designed to provide
interface level measurement performance well beyond
that of many traditional technologies. The innovative,
patented enclosure is a first in the industry orienting
both wiring and electronics compartments in the same
plane. The housing is also angled to maximize ease of
wiring, configuration, and data display.
LOWER MEDIA: Conductive media having a
dielectric greater than 15
VESSELS: Most process or storage vessels,
bridles and bypass chambers, up to rated
probe temperature and pressure
CONDITIONS: Interface level measurement and control applications with a
clean distinct interface, including those
with changing specific gravities and
visible vapors
T E C H N O L O G Y
F E A T U R E S
Eclipse Guided Wave Radar is based upon the technology of TDR (Time Domain Reflectometry). TDR utilizes
pulses of electromagnetic energy transmitted down a
wave guide (probe). When a pulse reaches a liquid surface that has a higher dielectric constant than the air
(dielectric constant of 1) in which it is traveling, the
pulse is reflected and ultra high speed timing circuitry
provides an accurate measure of liquid level. Even after
the pulse is reflected from the upper surface, some of
the energy continues down the length of the probe
through the upper liquid. The pulse is again reflected
when it reaches the higher dielectric lower liquid. Since
the speed of the signal through the upper liquid is
dependent on the dielectric constant of the medium in
which it is traveling, the dielectric constant of the upper
liquid must be known to accurately determine the
interface level.
Knowing the time between the first and second reflections, along with knowing the upper layer dielectric
constant, the thickness of the upper layer can be
determined.
• Two-wire, 24 VDC, loop-powered interface
level transmitter (4–20 mA output corresponds
to interface level)
• Optional HART digital communications can
output both upper layer and interface layer to
a HART interface module (not supplied)
• Performance is not process dependent
(changing SG has no effect)
• No level change needed for configuration
• Ultra-low dielectric capability (ε≥1.4) on
upper level measurement
• Can measure reliably to the very top
of the vessel
• Probe design to +400° F (+200° C), 1000 psi
(70 bar)
• IS, XP, and Non-incendive approvals
• Two-line, 8 character LCD and
3-button keypad (optional)
• Quick connect/disconnect probe coupling
T R A N S M I T T E R
S P E C I F I C A T I O N S
F U N C T I O N A L / P H Y S I C A L
Model 707
Signal output
4–20 mA or 4–20 mA with HART (optional)
3.8 to 20.5 mA useable (meets NAMUR NE 43)
Span
6 to 144 inches (15 to 366 cm)
Resolution
Analog
Display
Loop resistance
General purpose/Intrinsically safe
Explosion proof (with intrinsically safe probe)
Damping
0.01 mA
0.1 inch
620 Ω @ 24 VDC (20.5 mA)
500 Ω @ 24 VDC (20.5 mA)
Adjustable 0–45 seconds
Diagnostic alarm
Adjustable 3.6 mA, 22 mA, or HOLD
(3.6 mA diagnostic alarm not valid when
both HART and display are provided)
User interface
3-button keypad and/or HART communicator
(HART communicator Magnetrol P/N 89-5213-XXX sold separately)
2-line × 8-character LCD
Display
Power (at terminals)
General purpose/Intrinsically safe
Explosion proof (with intrinsically safe probe)
11 to 36 VDC
13.5 to 36 VDC
Menu language
English, Spanish, French or German
Housing material
Aluminum A356T6 (< 0.2% copper)
316 stainless steel (optional)
Net/Gross weight
Aluminum
316 stainless steel
6 lbs (2.36 kg) / 7 lbs (2.76 kg)
13.5 lbs (5.3 kg) / 14 lbs (5.7 kg)
H 8.43" (214 mm) × W 4.38" (111 mm) × D 7.40" (188 mm)
Overall dimensions
P E R F O R M A N C E
Use with probe
Model 7XT
Reference conditions
Reflection from water at +70° F (+20° C) with 72" probe
Linearity
Measured error
< 0.5 inch (13 mm)
Upper liquid layer
Lower liquid layer
±1 inch (25 mm)
±1 inch (25 mm)
Resolution
±0.1 inch (3 mm)
Repeatability
±0.5 inch (13 mm)
Hysteresis
±0.5 inch (13 mm)
Response time
Warm-up time
Operating temperature range
LCD temperature range
Operating temperature effect
Humidity
Electromagnetic compatibility
2
< 1 second
< 5 seconds
-40° to +175° F (-40° to +80° C)
-5° to +160° F (-20° to +70° C)
Approximately ±0.02% of probe length / °C
0–99%, non-condensing
Meets CE requirements (EN 61000-6-2/2001, EN 61000-6-4/2001)
A G E N C Y
AGENCY
FM
CSA
ATEX
A P P R O V A L S
MODEL APPROVED
APPROVAL CATEGORY
APPROVAL CLASSES
707-5XXX-1XX
707-5XXX-2XX
Intrinsically Safe
707-5XXX-3XX
707-5XXX-4XX
Explosion Proof ➀
(with Intrinsically Safe probe)
707-5XXX-1XX
707-5XXX-2XX
Non-Incendive
Suitable for: ➁
707-5XXX-1XX
707-5XXX-2XX
Intrinsically Safe
707-5XXX-3XX
707-5XXX-4XX
Explosion Proof ➀
(with Intrinsically Safe probe)
707-5XXX-1XX
707-5XXX-2XX
Non-Incendive
Suitable for: ➁
707-5XXX-AXX
707-5XXX-BXX
707-5XXX-CXX
707-5XXX-DXX
707-5XXX-EXX
707-5XXX-FXX
Intrinsically Safe
Class I, Div. 1; Groups A, B, C, & D
Class II, Div. 1; Groups E, F, & G
Class III, NEMA 4X
Entity
Class I, Div. 1; Groups B, C & D
Class II, Div. 1; Groups E, F, & G
Class III, NEMA 4X
Class I, Div. 2; Groups A, B, C, & D
Class II, Div. 2; Groups F & G
Class III, NEMA 4X
Class I, Div. 1; Groups A, B, C, & D
Class II, Div. 1; Group G
Class III, Type 4X
Entity
Class I, Div. 1; Groups B, C & D
Class II, Div. 1; Groups E, F, & G
Class III, Type 4X
Class I, Div. 2; Groups A, B, C, & D
Class II, Div. 2; Groups E, F, & G
Class III, Type 4X
II 1G, EEx ia IIC T4
Explosion Proof ➀
II 1/2G, EEx d [ia] IIC T4
Non-Incendive ➁
II 3G, EEx n IIC T4..T6
➀ Factory Sealed: This product has been approved by
Factory Mutual Research (FM), and Canadian Standards
Association (CSA), as a Factory Sealed device.
0344
➁ Measured media inside vessel must be non-flammable only.
R E M O T E
These units are in conformity of:
1. The EMC Directive: 89/336/EEC. The units have been
tested to EN 61000-6-2/2001 and EN 61000-6-4/2001.
2. Directive 94/9/EC for equipment or protective system for use
in potentially explosive atmospheres (8th digit "A" only).
A S S E M B L Y
The Local/Remote assembly is meant to be a simple and
cost-effective way to remove the transmitter electronics
and locate it a short distance away from the probe. The
assembly allows a remote distance of 33" (84 cm) which
offers a greater degree of flexibility during installation.
It is supplied with a remote bracket and flexible armor
as a complete assembly.
3.28
(83)
4.12
(105)
INCHES
(MM)
4.00
(102)
2.37
(60)
Elect.
Conn. (2)
45°
3.00
(76)
2.00
(51)
3.50
(89)
3.75
(95)
2 Holes
.38 (10) Dia.
33.00
(838)
4.25
(108)
3
P R O B E
O V E R V I E W
The coaxial probe, being the most efficient of all GWR probe configurations, is the
only probe offered with the Model 707 Interface Transmitter. Analogous to the efficiency of the modern, coaxial cable, a coaxial probe allows almost unimpeded
transmission of the high frequency pulses throughout its length.
The electromagnetic field that develops between the inner rod and outer tube is
completely contained, as shown in Figure 1. The efficiency and sensitivity of a coaxial configuration yields robust signal strength, even in applications having an upper
liquid layer dielectric constant as low as 1.4.
Figure 1
Coaxial Probe
INTERFACE
The sensitivity of this configuration also makes it more susceptible to measurement
errors in applications of coating and buildup. For this reason, interface measurement using the Eclipse Model 707 is only recommended in media with a viscosity
of 500 cp or less.
DETECTION
The Eclipse Model 707, designed for use with the Model 7XT coaxial probe, is a transmitter capable of measuring both
an upper liquid level and an interface liquid level. It is required that the upper liquid have a dielectric constant between
1.4 and 5, and the lower liquid have a dielectric constant greater than 15. A typical application would be oil over water,
with the upper layer of oil being non-conductive with a dielectric constant of around 2, and the lower layer of water
being very conductive with a dielectric constant of around 80. (This interface measurement can only be accomplished
when the dielectric constant of the upper medium is lower than the dielectric constant of the lower medium).
Reference
Signal
Air
(ε = 1)
Upper
Level
Signal
Low Dielectric
Medium
(e.g. oil, ε = 2)
Interface
Level
Signal
High Dielectric
Medium
(e.g. water, ε = 80)
Time
Figure 2
As mentioned earlier, Eclipse Guided Wave Radar is based upon
the technology of TDR (Time Domain Reflectometry). TDR utilizes
pulses of electromagnetic energy transmitted down a wave guide
(probe). When a pulse reaches a liquid surface that has a higher
dielectric constant than the air (dielectric constant of 1) in which it
is traveling, the pulse is reflected and ultra high speed timing circuitry provides an accurate measure of liquid level. Even after the
pulse is reflected from the upper surface, some of the energy continues down the length of the probe through the upper liquid. The
pulse is again reflected when it reaches the higher dielectric lower
liquid, as shown in Figure 2. Since the speed of the signal through
the upper liquid is dependent on the dielectric constant of the
medium in which it is traveling, the dielectric constant of the upper
liquid must be known to accurately determine the interface level.
Knowing the time between the first and second reflections, along with knowing the upper layer dielectric constant, the
thickness of the upper layer can be determined.
In order to properly process the reflected signals, the Model 707 is specified for those applications where the thickness
of the upper layer is greater than 2 inches. The maximum upper layer is limited to the length of the Model 7XT probe,
which is available in lengths up to 12 feet.
EMULSION
LAYERS
As emulsion layers can decrease the strength of the reflected signal, the Eclipse Model 707 should only be utilized in
those applications that have clean, distinct layers. Contact the factory for application assistance.
4
C O A X I A L
P R O B E
M A T R I X
7XT Interface
Temperatures to +400° F (+200° C);
clean, low viscosity liquids
Recommended for
Not recommended for
Coating and build-up, foam
Materials/Wetted parts
316L SS, TFE, Viton GFLT
Viton GFLT O-ring ➀
Process seal
Spacers
TFE
Diameter
∅ .3125 (8 mm) rod
∅ .875" (22 mm) tube
Process connection thread
⁄4" NPT, 1" BSP
3
Flange ANSI (DIN)
1 to 4" (DN25 to 100)
Length
24 to 144" (60 to 366 cm)
Transition zone ➁
Top
Bottom
Process temperature ➂
Maximum
Minimum/Cryogenic
Process pressure
Maximum
Minimum/Vacuum service
Dielectric range
Upper liquid layer
Interface liquid layer
Minimum upper layer thickness
None
6" (150 mm) @ εr = 1.4
1" (25 mm) @ εr = 80
+400° F @ 270 psig
(+200° C @ 18 bar)
-40° F @ 750 psig
(-40° C @ 50 bar)
1000 psig @ +70° F
(70 bar @ +20° C)
Yes, not hermetic
1.4 to 5
15 to 100
2 inches
Maximum viscosity (cP)
500
Mounting effects
None
Coating/Build-up
No
Foam
No
Corrosives
Yes
Sanitary
No
Overfill
Yes
Approvals
FM
CSA
ATEX
Use with transmitter
➀ Refer to Selection Chart on page 6 for optional o-rings.
Yes
Yes
Yes
707
➁ Transition Zone is dielectric dependent: εr = dielectric
permittivity. Unit will function but accuracy will decrease
in Transition Zone.
5
O - R I N G
Material
( S E A L )
Maximum
Temperature
Code
S E L E C T I O N
Maximum
Pressure
Min.
Temp.
C H A R T
Recommended
For Use In
Not Recommended
For Use In
Viton GFLT
0
+400° F @ 232 psig 1000 psig @ +70° F
(+200° C @ 16 bar) (70 bar @ +20° C)
-40° F
(-40° C)
General purpose, steam,
ethylene
Ketones (MEK, acetone),
skydrol fluids, amines,
anhydrous ammonia, low molecular
weight esters and ethers, hot hydrofluoric or chlorosuforic acids, sour HCs
EPDM
1
+250° F @ 200 psig 1000 psig @ +70° F
(+125° C @ 14 bar) (70 bar @ +20° C)
-60° F
(-50° C)
Acetone, MEK, skydrol fluids
anhydrous ammonia,
Petroleum oils, di-ester base
lubricants, propane, steam
Inorganic and organic acids
(including HF and nitric)
aldehydes, ethylene, glycols,
organic oils, silicone oils,
vinegar, sour HCs
amines, ethylene oxide,
propylene oxide
Black liquor, hot water/steam,
hot aliphatic amines, ethylene oxide
propylene oxide, molten sodium,
molten potassium
Inorganic and organic acids
(including HF and nitric)
aldehydes, ethylene, glycols,
organic oils, silicone oils,
vinegar, sour HCs, steam,
amines, ethylene oxide,
propylene oxide
Black liquor, Freon 43,
Freon 75, Galden, KEL-F liquid,
molten sodium, molten potassium
Kalrez (4079)
Aegis PF128
+400° F @ 232 psig 1000 psig @ +70° F
(+200° C @ 16 bar) (70 bar @ +20° C)
2
+400° F @ 232 psig 1000 psig @ +70° F
+(200° C @ 16 bar) (70 bar @ +20° C)
8
T E M P E R A T U R E /
P R E S S U R E
C H A R T
-40° F
(-40° C)
-4° F
(-20° C)
D I M E N S I O N A L
S P E C I F I C A T I O N S
Process Pressure, psi
I N C H E S
1200
1100
1000
900
800
700
600
500
400
300
200
100
0
3.28
(83)
( M M )
4.12
(105)
4.00
(102)
10.08
(256)
Elect.
Conn. (2)
50
150
250
350
45°
450
7XT
Process
Conn.
Probe
Insertion
Length
Eclipse with Coaxial
Model 7XT Probe
NPT Threaded
Connection
6
6.61
(168)
5.68
(144)
Process Temperature, °F (max. 400)
Process
Conn.
Probe
Insertion
Length
Eclipse with Coaxial
Model 7XT Probe
Flanged Connection
T O R Q U E
T U B E
R E P L A C E M E N T
Eclipse has proven to be the perfect replacement for existing torque tube transmitters. In hundreds of applications
around the globe, customers have found Eclipse Guided Wave Radar superior to torque tube transmitters:
• Cost:
A new Eclipse costs only slightly more than
rebuilding an aging torque tube.
• Installation:
No field calibration is necessary; it can be
configured in minutes with no level movement.
• Performance:
Eclipse is not affected by changes
in specific gravity or dielectric.
• Robust:
There are no moving parts to wear
out and fail.
• Ease of Replacement:
Proprietary flanges are offered so existing
chamber/cages can be used.
See the table below for determining the proper probe length for your installation. It is recommended to further confirm the probe length by measuring from the bottom of the transmitter flange to the bottom (internal) of the chamber.
Manufacturer
Flange Type ➀➁
(Eclipse Digits 5, 6)
Displacer Length
inches (mm)
Proprietary ➀
≥14" (355)
Displacer + 10" (254)
ANSI
≥14" (355)
Consult Factory
Proprietary ➀
≥14" (355)
Displacer + 13.6" (345)➂
ANSI/DIN
≥16" (406)
Displacer + 8" (203)
Consult Factory
Probe Length =
(Eclipse Digits 8, 9, 10)
Fisher®: Series 2300 & 2500
Chamber: 249B, 259B, 249C
Chamber: Others
Masoneilan®: Series 12000
Standard
Others
Eckardt: Series 134, 144
ANDI/DIN
≥14" (355)
Tokyo Keiso: FST-3000 Series
ANSI/DIN
H = 11.8" (300)
ANSI/DIN
H = 19.7" (500)
Magnetrol: Modulevel (Existing)
ANSI/DIN
14" (355)
Displacer + 12.6" (320)➂
ANSI/DIN
≥17" (432)
Displacer + 8.5" (216)
Displacer + 15" (381)➂
Displacer + 9.8" (250)
➀ Proprietary (Fisher and Masoneilan) flanges are carbon steel (typical); flanges for 249C are 316
stainless steel (see digits 5 and 6 in Model Number).
➁ NACE–stainless steel flanges; welded connection is acceptable, must use NPT connection for
CS flanges due to hardness issues.
➂ All 14" (355 mm) displacers from Masoneilan, Tokyo Keiso (H = 11.8" / 300 mm) and Magnetrol
must use a “Top Hat” flange extension to meet the 24" (610) minimum probe length requirement.
The flange extension adds an extra 5.5" (140 mm) to top of probe flange.
7
T O R Q U E
T U B E
R E P L A C E M E N T
( c o n t . )
NOTE: Due to changes in proprietary flanges over time, please confirm the proprietary flange type by comparing dimensions
to the following drawings:
INCHES (MM)
9.0 ∅
(229)
5.625 ∅
(143)
7.25 ∅
(184)
7.50 ∅
(191)
4.750 ∅
(121)
45°
45°
.875 ∅
(22)
45°
.875 ∅
(22)
.438 ∅
(11)
1.125
(32)
5.23
(133)
Fisher 249B/259B (600 lb.), carbon steel
1.125
(29)
1.125
(29)
3.375
(86)
.22
(6)
4.00
(102)
.188
(5)
Fisher 249C (600 lb.), 316 stainless steel
If a new chamber is needed, Magnetrol offers the most complete line in the industry.
The chambers are offered with all of the most popular options.
12–240 inches (30–610 cm)
Carbon steel or 316 stainless steel
3
⁄4", 1", 11⁄2", 2"
150#-2500# ANSI
Side–Side and Side–Bottom
Up to 5000 psig (345 bar)
Up to +750° F (+400° C)
See Sales Bulletin 41-140 and Technical Bulletin 41-640 for
complete chamber information.
A U R O R A®
The next generation of Magnetic Level Indicator is here with the introduction of Aurora.
Aurora is the innovative combination of a magnetic level indicator and an Eclipse
Guided Wave Radar transmitter. This approach yields a highly visible, local indicator
with the 4–20 mA of Eclipse; a totally redundant installation. Eclipse will continue to
reliably report the level even if the float becomes damaged.
See Sales Bulletin 46-138 for complete information.
8
.25
(6)
Masoneilan (600 lb.), carbon steel
C H A M B E R S
Measuring span
Materials of construction
Process connection sizes
Process connection ratings
Configurations
Process pressures
Process temperatures
5.875 ∅
(149)
T R A N S M I T T E R
M O D E L
N U M B E R
BASIC MODEL NUMBER
707
Eclipse Guided Wave Radar Interface Level Transmitter for use with probe model 7XT only
POWER
5
24 VDC, Two-Wire
SIGNAL OUTPUT
0
1
4–20 mA only, without HART (must be ordered with Accessory Code A)
4–20 mA with HART (HART communicator Magnetrol P/N 89-5213-XXX sold separately)
MENU LANGUAGE
1
2
3
4
English
Spanish
French
German
ACCESSORIES
0
A
No digital display and keypad (must be ordered with Signal Output Code 1)
Digital display and keypad
MOUNTING/CLASSIFICATION
1
2
3
4
A
B
C
D
E
F
Integral, General Purpose & Intrinsically Safe
(FM & CSA), Non-incendive (Class I, Div. 2)
Remote, General Purpose & Intrinsically Safe
(FM & CSA), Non-incendive (Class I, Div. 2)
Integral, Explosion Proof (FM & CSA)
Remote, Explosion Proof (FM & CSA)
Integral, General Purpose & Intrinsically Safe
(ATEX & JIS EEx ia IIC T4)
Remote, General Purpose & Intrinsically Safe
(ATEX & JIS EEx ia IIC T4)
Integral, Explosion Proof (ATEX EEx d ia IIC T4)
(must be ordered with Conduit Connection Codes 0 and 1)
Remote, Explosion Proof (ATEX EEx d ia IIB T4)
(must be ordered with Conduit Connection Codes 0 and 1)
Integral, Non-incendive (ATEX EEx n IIC T6) (Model 705 only)
Remote, Non-incendive (ATEX EEx n IIC T6) (Model 705 only)
HOUSING
1
2
Cast aluminum, dual compartment, 45° angle
316 stainless steel, dual compartment, 45° angle
CONDUIT CONNECTION
0
1
2
3
7
0
7
⁄4" NPT
M20
PG 13.5
PG 16
3
5
9
P R O B E
M O D E L
N U M B E R
BASIC MODEL NUMBER
7E
Eclipse GWR probe, English unit of measure
7M
Eclipse GWR probe, Metric unit of measure
CONFIGURATION/STYLE
T
(Dielectric range ≥1.4)
Coaxial, Interface, 3⁄4" process connection or larger
MATERIAL OF CONSTRUCTION
A
B
C
316/316L stainless steel
Hastelloy C
Monel
THREADED CONNECTIONS
11
22
3
⁄4" NPT Thread
1" BSP Thread
ANSI RAISED FACE FLANGE CONNECTIONS
23
24
25
33
34
35
43
44
45
53
54
55
63
64
65
1" 150#
1" 300#
1" 600#
11⁄2" 150#
11⁄2" 300#
11⁄2" 600#
2" 150#
2" 300#
2" 600#
3" 150#
3" 300#
3" 600#
4" 150#
4" 300#
4" 600#
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
ANSI Raised Face Flange
Proprietary and Specialty Flange & DIN Flange Connections
continued on next page
O-RINGS
Refer to next page
LENGTH
Refer to next page
7
10
T
A
P R O B E
M O D E L
c o n t i n u e d
N U M B E R
PROPRIETARY AND SPECIALTY FLANGE CONNECTIONS
4R
4S
5R
5S
TT
TU
UT
UU
UV
UW
2" 150#
2" 300/600#
3" 150#
3" 300/600#
31⁄2'' 600#
31⁄2'' 600#
21⁄2'' 600#
31⁄2'' 600#
31⁄2'' 600#
31⁄2'' 600#
ANSI Raised Face Carbon Steel Flange with Top Hat
ANSI Raised Face Carbon Steel Flange with Top Hat
ANSI Raised Face Carbon Steel Flange with Top Hat
ANSI Raised Face Carbon Steel Flange with Top Hat
Fisher - Proprietary Carbon Steel (249B) Torque Tube Flange
Fisher - Proprietary 316 Stainless Steel (249C) Torque Tube Flange
Masoneilan - Proprietary Carbon Steel Torque Tube Flange
Masoneilan - Proprietary 316 Stainless Steel Torque Tube Flange
Masoneilan - Proprietary Carbon Steel Torque Tube Flange with Top Hat
Masoneilan - Proprietary 316 Stainless Steel Torque Tube Flange with Top Hat
DIN FLANGE CONNECTIONS
BA
BB
CA
CB
DA
DB
EA
EB
FA
FB
DN
DN
DN
DN
DN
DN
DN
DN
DN
DN
25,
25,
40,
40,
50,
50,
80,
80,
100,
100,
PN 16
PN 25/40
PN 16
PN 25/40
PN 16
PN 25/40
PN 16
PN 25/40
PN 16
PN 25/40
DIN 2527 Form B Flange
DIN 2527 Form B Flange
DIN 2527 Form B Flange
DIN 2527 Form B Flange
DIN 2527 Form B Flange
DIN 2527 Form B Flange
DIN 2527 Form B Flange
DIN 2527 Form B Flange
DIN 2527 Form B Flange
DIN 2527 Form B Flange
O-RINGS
0
Viton GFLT
1
EPDM (Ethylene Propylene Rubber)
2
Kalrez 4079
8
Aegis PF128
LENGTH
24" to 144" (60 cm to 366 cm)
(unit of measure is determined by second digit of Model Number)
Examples: 24 inches = 024; 60 centimeters = 060
7
T
A
PROCESS CONNECTION SIZE/TYPE
Insertion Length
NPT Process Connection
Insertion Length
BSP Process Connection
Insertion Length
ANSI or DIN Welded Flange
11
Q U A L I T Y
The quality assurance system in place at
Magnetrol guarantees the highest level of
quality throughout the company. Magnetrol
is committed to providing full customer
satisfaction both in quality products and
quality service.
Magnetrol’s quality assurance system is
registered to ISO 9001 affirming its commitment to known international quality
standards providing the strongest assurance
of product/service quality available.
W A R R A N T Y
All Magnetrol electronic level and flow
controls are warranted free of defects in
materials or workmanship for one full year
from the date of original factory shipment.
If returned within the warranty period; and,
upon factory inspection of the control, the
cause of the claim is determined to be covered under the warranty; then, Magnetrol
will repair or replace the control at no cost
to the purchaser (or owner) other than
transportation.
Magnetrol shall not be liable for misapplication, labor claims, direct or consequential
damage or expense arising from the installation or use of equipment. There are no
other warranties expressed or implied,
except special written warranties covering
some Magnetrol products.
For additional information, see Instruction Manual 57-600.
5300 Belmont Road • Downers Grove, Illinois 60515-4499 • 630-969-4000 • Fax 630-969-9489 • www.magnetrol.com
145 Jardin Drive, Units 1 & 2 • Concord, Ontario Canada L4K 1X7 • 905-738-9600 • Fax 905-738-1306
Heikenstraat 6 • B 9240 Zele, Belgium • 052 45.11.11 • Telex 25944 • Fax 052 45.09.93
Regent Business Ctr., Jubilee Rd. • Burgess Hill, Sussex RH15 9TL U.K. • 01444-871313 • Fax 01444-871317
Copyright © 2003 Magnetrol International, Incorporated. All rights reserved. Printed in the USA.
Magnetrol and Magnetrol logotype are registered trademarks of Magnetrol International.
Performance specifications are effective with date of issue and are subject to change without notice.
The brand and product names contained within this document are trademarks or registered trademarks of their respective holders.
BULLETIN: 57-107.2
EFFECTIVE: November 2003
SUPERSEDES: February 2003