DATA SHEET GaAs MULTI-CHIP MODULE MC-7845 870 MHz CATV 18 dB POWER DOUBLER AMPLIFIER DESCRIPTION The MC-7845 is a GaAs Multi-chip Module designed for use in CATV applications up to 870 MHz. This unit has low distortion, low noise figure and return loss across the entire frequency band. Reliability and performance uniformity are assured by our stringent quality and control procedures. FEATURES • Low distortion • High linear gain GL = 18.0 dB MIN. @f = 870 MHz • Low return loss ORDERING INFORMATION Part Number MC-7845 Package 7-pin special with heatsink Supplying Form 50 pcs MAX./Tray Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: MC-7845 ABSOLUTE MAXIMUM RATINGS (TA = +25°°C) Parameter Symbol Ratings Unit VDD 30 V Vi 65.0 dBmV Operating Case Temperature TC −30 to +100 °C Storage Temperature Tstg −40 to +100 °C Supply Voltage Input Voltage Note Note In case of single tone Caution The IC must be handled with care to prevent static discharge because its circuit composed of GaAs MES FET. The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. Not all devices/types available in every country. Please check with local NEC representative for availability and additional information. Document No. PG10138EJ01V0DS (1st edition) Date Published April 2002 CP(K) Printed in Japan The mark ! shows major revised points. NEC Compound Semiconductor Devices 2001, 2002 MC-7845 RECOMMENDED OPERATING CONDITIONS (ZS = ZL = 75 Ω) Parameter Supply Voltage Input Voltage Symbol Test Conditions MIN. TYP. MAX. Unit 23.5 24.0 24.5 V − 36.0 39.0 dBmV −30 +25 +85 °C MIN. TYP. MAX. Unit f = 870 MHz 18.0 − 19.0 dB f = 40 to 870 MHz 0.2 0.6 1.0 dB f = 40 to 870 MHz, Peak to valley − − 0.6 dB VDD Vi 110 channel, 10 dB tilted across the band Operating Case Temperature TC ELECTRICAL CHARACTERISTICS (TC = 30 ± 5°°C, VDD = 24 V, ZS = ZL = 75 Ω) Parameter Symbol Linear Gain GL Gain Slope GSlope Test Conditions Gain Flatness GFlatness Noise Figure 1 NF1 f = 50 MHz − − 6.5 dB Noise Figure 2 NF2 f = 870 MHz − − 7.0 dB Operating Current IDD RF OFF 275 − 375 mA 110 channel, − − −60 dBc Composite Triple Beat CTB Cross Modulation XM VO = 50 dBmV at 745.25 MHz, − − −55 dBc 10 dB tilted across the band − − −63 dBc Composite 2nd Order Beat CSO Input Return Loss 1 RLi1 f = 40 to 160 MHz 20 − − dB Input Return Loss 2 RLi2 f = 160 to 320 MHz 19 − − dB Input Return Loss 3 RLi3 f = 320 to 640 MHz 17.5 − − dB Input Return Loss 4 RLi4 f = 640 to 870 MHz 16 − − dB Output Return Loss 1 RLo1 f = 40 to 160 MHz 20 − − dB Output Return Loss 2 RLo2 f = 160 to 320 MHz 19 − − dB Output Return Loss 3 RLo3 f = 320 to 640 MHz 17.5 − − dB Output Return Loss 4 RLo4 f = 640 to 870 MHz 16 − − dB 2 Data Sheet PG10138EJ01V0DS MC-7845 PACKAGE DIMENSIONS 7-PIN SPECIAL WITH HEATSINK (UNIT: mm) 8.1 MAX. 38.1±0.25 φ 4.25–0.35 +0.25 27.5 MAX. 4.0±0.25 14.85 MAX. 3.2 MAX. 45.08 MAX. 19.05±0.38 25.4±0.25 6-32UNC2B 0.51±0.05 10.75±0.25 7 8 9 2.62±0.35 5 12.9 MAX. 1 2 3 21.5 MAX. 4.19±0.13 2.54±0.25 A 2.54±0.38 6.3 0.51±0.05 2.5 0.38.. A ±0.05 PIN CONNECTION VDD 5 1 9 IN OUT 2 3 7 8 GND Data Sheet PG10138EJ01V0DS 3 MC-7845 NOTE ON CORRECT USE (1) The space between PC board and root of the lead should be kept more than 1 mm to prevent undesired stress to the lead and also should be kept less than 4 mm to prevent undesired parasitic inductance. Recommended that space is 2.0 to 3.0 mm typical. (2) (3) Recommended torque strength of the screw is 59 to 78 Ncm. Form the ground pattern as wide as possible to minimize ground impedance. (to prevent undesired oscillation) All the ground pins must be connected together with wide ground pattern to decrease impedance difference. RECOMMENDED SOLDERING CONDITIONS This product should be soldered in the following recommended conditions. Other soldering methods and conditions than the recommended conditions are to be consulted with our sales representatives. Soldering Method Pin Part Heating Soldering Conditions Pin area temperature : less than 350°C Condition Symbol Note Hour : Within 3 sec./pin Note The point of pin part heating must be kept more than 1.2 mm distance from the root of lead. 4 Data Sheet PG10138EJ01V0DS − MC-7845 • The information in this document is current as of April, 2002. The information is subject to change without notice. For actual design-in, refer to the latest publications of NEC's data sheets or data books, etc., for the most up-to-date specifications of NEC semiconductor products. Not all products and/or types are available in every country. Please check with an NEC sales representative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without prior written consent of NEC. NEC assumes no responsibility for any errors that may appear in this document. • NEC does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from the use of NEC semiconductor products listed in this document or any other liability arising from the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC or others. • Descriptions of circuits, software and other related information in this document are provided for illustrative purposes in semiconductor product operation and application examples. The incorporation of these circuits, software and information in the design of customer's equipment shall be done under the full responsibility of customer. NEC assumes no responsibility for any losses incurred by customers or third parties arising from the use of these circuits, software and information. • While NEC endeavours to enhance the quality, reliability and safety of NEC semiconductor products, customers agree and acknowledge that the possibility of defects thereof cannot be eliminated entirely. To minimize risks of damage to property or injury (including death) to persons arising from defects in NEC semiconductor products, customers must incorporate sufficient safety measures in their design, such as redundancy, fire-containment, and anti-failure features. • NEC semiconductor products are classified into the following three quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to semiconductor products developed based on a customer-designated "quality assurance program" for a specific application. The recommended applications of a semiconductor product depend on its quality grade, as indicated below. Customers must check the quality grade of each semiconductor product before using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC semiconductor products is "Standard" unless otherwise expressly specified in NEC's data sheets or data books, etc. If customers wish to use NEC semiconductor products in applications not intended by NEC, they must contact an NEC sales representative in advance to determine NEC's willingness to support a given application. (Note) (1) "NEC" as used in this statement means NEC Corporation, NEC Compound Semiconductor Devices, Ltd. and also includes its majority-owned subsidiaries. (2) "NEC semiconductor products" means any semiconductor product developed or manufactured by or for NEC (as defined above). M8E 00. 4 - 0110 Data Sheet PG10138EJ01V0DS 5 MC-7845 SAFETY INFORMATION ON THIS PRODUCT Caution GaAs Products The product contains gallium arsenide, GaAs. GaAs vapor and powder are hazardous to human health if inhaled or ingested. • Do not destroy or burn the product. • Do not cut or cleave off any part of the product. • Do not crush or chemically dissolve the product. • Do not put the product in the mouth. Follow related laws and ordinances for disposal. The product should be excluded from general industrial waste or household garbage. Business issue NEC Compound Semiconductor Devices, Ltd. 5th Sales Group, Sales Division TEL: +81-3-3798-6372 FAX: +81-3-3798-6783 E-mail: [email protected] NEC Compound Semiconductor Devices Hong Kong Limited Hong Kong Head Office FAX: +852-3107-7309 TEL: +852-3107-7303 Taipei Branch Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Korea Branch Office FAX: +82-2-528-0302 TEL: +82-2-528-0301 NEC Electron Devices European Operations http://www.nec.de/ TEL: +49-211-6503-101 FAX: +49-211-6503-487 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279 Technical issue NEC Compound Semiconductor Devices, Ltd. http://www.csd-nec.com/ Sales Engineering Group, Sales Division E-mail: [email protected] FAX: +81-44-435-1918 0110