ALUMINUM ELECTROLYTIC CAPACITORS WZ Chip Type, Wide Temperature Range High Temperature (260°C) Reflow series Corresponding with 260°C peak reflow soldering Recomended reflow condition : 260°C peak 5 sec 230°C over 60 sec 2 times (φ8 × 6.2, φ10 × 10 : 1 time) Chip type operating over wide temperature range of to – 55 to +105°C. WZ Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU). High Temperature Reflow WT Specifications Performance Characteristics Item Category Temperature Range –55 to +105°C Rated Voltage Range 6.3 to 50V Rated Capacitance Range 0.1 to 1500µF Capacitance Tolerance ±20% at 120Hz, 20°C Leakage Current After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (µA) , whichever is greater. Measurement frequency : 120Hz at 20°C 6.3 0.30 Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.24 16 0.20 25 0.16 35 0.14 50 0.14 Measurement frequency : 120Hz Rated voltage (V) Z– 25°C / Z+20°C Impedance ratio Stability at Low Temperature ZT / Z20 (MAX.) Z– 40°C / Z+20°C The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 105°C. Endurance Resistance to soldering heat Marking Chip Type L±0.3 L±0.3 E H 3 H A B H H E H A±0.2 E L±0.5 5 4 6 5 7 6 8 7 9 8 10 11 12 13 14 9 10 11 12 13 14 φD code φD 4 to 6.3 (5.4L) GB 4 to 6.3 (5.4L) 6.3 to 10 (L 5.8L) GS 6.3 to 10 (L 5.8L) A±0.2 ×L L A±0.2 0.5 MAX. C±0.2 B±0.2 C±0.2 3 (mm) φD Positive A±0.2 A±0.2 0.5 MAX. E L±0.5 Capacitance Lot No. Capacitance B±0.2 φD±0.5 Series Plastic platform Plastic platform 0.3 MAX. 0.3 MAX. 4 2 Negative Negative code GB GS Package code Package code Configuration Configuration Capacitance tolerance (±20%) Capacitance tolerance (±20%) Rated capacitance (33µF) Rated capacitance (33µF) Rated voltage (6.3V) Rated voltage (6.3V) Series name Series name Type Type Negative Negative Positive φD±0.5 A2 220E WZ A2 220E WZ 1 C Voltage (E:25V) Voltage (E:25V) Series 2 Positive A±0.2 A±0.2 0.5 MAX. E C±0.2 B±0.2 B±0.2 φD±0.5 φD±0.5 Series A2 220j WZ A2 220j WZ Series C±0.2 0.5 MAX. Positive Plastic platform Plastic platform 0.3 MAX. 0.3 MAX. 1 U WUZW0Z J 0 3J 3303M0 CM LC1LG1BG B Negative Negative H (φ8 ×(φ8 10, ×φ10×10) 10, φ10×10) Lot No. 50 2 3 Within ±25% of the initial capacitance value for capacitors of 16V or less. Within ±20% of the initial capacitance value for capacitors of 25V or more. 200% or less than the initial specified value tan δ Leakage current Less than or equal to the initial specified value A±0.2 L +0.1 –0.2 H 1 (L±0.3) 1 1 Apply to φ6.3 × 5.8, φ6.3 × 7.7 1 Apply to φ6.3 × 5.8, φ6.3 × 7.7 Capacitance Lot No. Capacitance Trade mark Trade mark 35 2 3 A±0.2 E +0.1 –0.2 (L±0.3) Positive A±0.2 A±0.2 0.5 MAX. E C±0.2 (φ8 ×(φ8 6.2 ×) 6.2 ) Voltage ( J:6.3V) Voltage ( J:6.3V) Lot No. 25 2 4 Capacitance change A±0.2 L C±0.2 B±0.2 B±0.2 φD±0.5 φD±0.5 Series A2 33C WZ A2 33C WZ Series Plastic platform Plastic platform 0.3 MAX. 0.3 MAX. 0.5 MAX. Positive Capacitance Lot No. Capacitance Trade mark Trade mark 16 2 4 Type numbering system (Example : 6.3V 33µF) (φ4 to(φ4 φ6.3 to )φ6.3 ) Lot No. 10 3 8 After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, which is Capacitance change Within ±10% of the initial capacitance value maintained at 250°C. The capacitors shall meet the Less than or equal to the initial specified value tan δ characteristic requirements listed at right when they are Less than or equal to the initial specified value Leakage current removed from the plate and restored to 20°C. Black print on the case top. Shelf Life Voltage (C:16V) Voltage (C:16V) 6.3 4 8 (mm) φD4××L5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 4 × 5.4 5 × 5.4 6.3 × 5.4 6.3 × 5.8 6.3 × 7.7 8 × 6.2 8 × 10 10 × 10 1.8 A 4.3 B 4.3 C 1.0 E 5.4 L 1.8 4.3 4.3 1.0 5.4 2.1 5.3 5.3 1.3 5.4 2.1 5.3 5.3 1.3 5.4 2.4 6.6 6.6 2.2 5.4 2.4 6.6 6.6 2.2 5.4 2.4 6.6 6.6 2.2 5.4 2.4 6.6 6.6 2.2 5.4 2.4 6.6 6.6 2.2 7.7 2.4 6.6 6.6 2.2 7.7 3.3 8.3 8.3 2.3 6.2 3.3 8.3 8.3 2.3 6.2 2.9 2.9 3.2 3.2 8.3 10.3 8.3 10.3 8.3 10.3 8.3 10.3 3.1 10 3.1 10 4.5 10 4.5 10 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 H 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Voltage V Code 6.3 10 16 25 35 50 j A C E V H Dimension table in next page. CAT.8100D ALUMINUM ELECTROLYTIC CAPACITORS WZ series Dimensions Cap. (µF) V 6.3 10 16 25 35 50 Code 0J 1A 1C 1E 1V 1H 0.1 0R1 4 × 5.4 1.0 0.22 R22 4 × 5.4 2.6 0.33 R33 4 × 5.4 3.2 0.47 R47 4 × 5.4 3.8 1 010 4 × 5.4 2.2 2R2 4 × 5.4 11 3.3 3R3 4.7 4R7 4 × 5.4 14 4 × 5.4 13 4 × 5.4 15 5 × 5.4 19 18 5 × 5.4 23 5 × 5.4 25 6.3 × 5.4 30 10 100 22 220 4 × 5.4 22 5 × 5.4 33 330 5 × 5.4 30 5 × 5.4 47 470 5 × 5.4 36 100 101 6.3 × 5.4 60 150 151 6.3 × 5.8 220 221 8 × 6.2 330 331 6.3 × 7.7 470 471 680 681 1000 1500 6.3 4 × 5.4 27 5 × 5.4 30 6.3 × 5.4 38 6.3 × 5.4 42 8 × 6.2 51 35 6.3 × 5.4 40 6.3 × 5.4 48 8 × 6.2 59 6.3 × 7.7 60 6.3 × 5.4 46 6.3 × 5.4 50 8 × 6.2 66 6.3 × 5.8 63 6.3 × 7.7 63 6.3 × 5.4 60 6.3 × 5.4 60 6.3 × 7.7 91 6.3 × 7.7 84 8 × 10 140 86 6.3 × 5.8 86 6.3 × 7.7 95 8 × 10 140 8 × 10 155 10 × 10 180 102 6.3 × 7.7 105 6.3 × 7.7 105 8 × 10 155 10 × 10 190 10 × 10 220 105 8 × 10 195 8 × 10 195 10 × 10 190 10 × 10 300 8 × 10 210 8 × 10 210 8 × 10 210 10 × 10 300 8 × 10 210 10 × 10 310 10 × 10 310 102 10 × 10 230 10 × 10 310 152 10 × 10 310 Case size φ D × L (mm) Rated ripple Rated ripple current (mArms) at 105°C 120Hz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.70 120 Hz 1.00 300 Hz 1.17 1 kHz 1.36 10 kHz or more 1.50 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity. CAT.8100D