LT - Nichicon

ALUMINUM ELECTROLYTIC CAPACITORS
LT
Chip Type, High Voltage.
High Temperature Range.
series
Chip type, high voltage and high temperature range.
Load life of 2000 hours at +125°C.
Applicable to automatic mounting machine
using carrier tape.
Compliant to the RoHS directive (2011/65/EU).
LH
LT
Long Life
High
Voltage
UB
Specifications
Item
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Performance Characteristics
–40 to +125°C
160 to 500V
1.8 to 33µF
± 20% at 120Hz, 20°C
Leakage Current
Rated voltage (V)
–
Tangent of loss angle (tan δ)
Rated voltage (V)
tan δ (MAX.)
160~450
0.04CV+100(μA)max.(1 minute's)
500
0.04CV+200(μA)max.(1 minute's)
Measurement frequency : 120Hz at 20°C
160
0.20
200
0.20
250
0.25
450
0.30
400
0.25
500
0.30
Measurement frequency : 120Hz
Rated voltage (V)
Impedance ratio
Z–40°C / Z+20°C
ZT / Z20 (MAX.)
Stability at Low Temperature
160
200
250
400
450
500
6
6
10
10
15
15
Capacitance change
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 125°C.
Endurance
Leakage current
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
Within ±10% of the initial capacitance value
Capacitance change
which is maintained at 250°C and then performing voltage
treatment based on JIS C 5101-4 clause 4.1 at 20°C, they
Less than or equal to the initial specified value
tan δ
shall meet the characteristic requirements listed at right
Less than or equal to the initial specified value
Leakage current
when they are removed from the plate.
Black print on the case top.
Shelf Life
Resistance to soldering
heat
Marking
Chip Type
Type numbering system (Example : 400V 6.8µF)
Plastic platform
0.3MAX.
Voltage(2G : 400V)
Series
C±0.2
A
B
C
E
L
H
8 × 10 10 × 10
2.9
3.2
10.3
8.3
10.3
8.3
3.1
4.5
10
10
0.8 to 1.1 0.8 to 1.1
3
4
5
6
7
8
9 10 11 12 13 14
A±0.2
Taping code
Configuration
A±0.2
L±1.0
Capacitance tolerance (±20%)
Rated capacitance (6.8µF)
Negative
H
Pressure relief vent
φD × L
2
U L T 2 G 6 R 8 MNL 1 GS
E
B±0.2
φD±0.5
A2
6.8 2G
LT
Lot No.
Capacitance
1
Positive
0.5MAX.
(φ8 × 10L, φ10)
Trade mark
Within ±30% of the initial capacitance value
300% or less than the intial specified value
Less than or equal to the initial specified value
tan δ
Rated voltage (400V)
(mm)
Series name
10 × 13.5
3.2
10.3
10.3
4.5
13.5
0.8 to 1.1
Type
Voltage
V
Code
160 200 250 400 450 500
2C
2D
2E
2G
2W
2H
Dimensions
Cap.(µF)
1.8
3.3
3.9
4.7
5.6
6.8
7.5
8.2
10
12
15
18
22
27
33
160
2C
V
Code
1R8
3R3
3R9
4R7
5R6
6R8
7R5
8R2
100
120
150
180
220
270
330
200
2D
8 × 10
45
10 × 10
60
10 × 13.5
65
250
2E
8 × 10
45
10 × 10
60
10 × 13.5
65
400
2G
8 × 10
30
10 × 10
10 × 13.5
45
50
450
2W
8 × 10
30
10 × 10
45
10 × 13.5
50
8 × 10
20
10 × 10
35
10 × 13.5
40
8 × 10
10 × 10
500
2H
20
35
10 × 13.5
40
Case size
φ D × L (mm)
Rated
ripple
Rated ripple current (mArms) at 125°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Please refer to page 3 for the minimum order quantity.
CAT.8100D