CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS HT High Temperature (125°C) series Low ESR, High Capacitance, High ripple current. Load life of 1000 hours at 125°C. Radial lead type : Lead free flow soldering condition correspondence. Compliant to the RoHS directive (2011/65/EU). HT Specifications Item Performance Characteristics Category Temperature Range –55 to +125°C Rated Voltage Range 6.3 to 35V Rated Capacitance Range 100 to 820µF Capacitance Tolerance ±20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) Less than or equal to the specified value. Endurance After 2 minutes' application of rated voltage at 20°C Test condition 125°C, rated voltage 1000Hrs. Capacitance change Within ±20% of initial value before test tan δ 150% or less than the initial specified value ESR( 1) 150% or less than the initial specified value Leakage current ( 2) Less than or equal to the initial specified value 1 ESR should be measured at both of the terminal ends closest to the capacitor body. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. Size List Cap [µF] R.V.(V) S.V.( V) Aluminum case [φD×L(mm)] 6.3 10 16 20 35 7.2 11.5 18.4 23.0 40.2 100 Stand off Wire(Lead free) 10×12.5 150 10×12.5 8×11.5 220 270 10×12.5 330 8×11.5 390 8×11.5 560 10×12.5 10×12.5 (mm) φD×L φd P α 680 10×12.5 8×11.5 0.6 3.5 1.5 820 10×12.5 10×12.5 0.6 5.0 1.5 Dimension table in next page. CAT.8100D CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS HT series Standard Ratings Rated Voltage Surge Voltage (V) (V) (code) 6.3 (0J) 10 (1A) 16 (1C) 20 (1D) 35 (1V) Rated Ripple Current Leakage ESR (mArms) Current (mΩ, 100kHz) (µA, 2min.) Rated Capacitance (µF) Case Size φD×L (mm) tan δ 680 10×12.5 0.12 857 12 5450 820 10×12.5 0.12 1033 12 220 8×11.5 0.12 440 330 8×11.5 0.12 390 8×11.5 560 NICHICON FPCAP 1740 RHT0J681MDN1□□ FP-6R3RE681M-HT□□ 5450 1740 RHT0J821MDN1□□ FP-6R3RE821M-HT□□ 17 3950 1260 RHT1A221MDN1□□ FP-010RE221M-HT□□ 660 17 3950 1260 RHT1A331MDN1□□ FP-010RE331M-HT□□ 0.12 780 16 3950 1260 RHT1A391MDN1□□ FP-010RE391M-HT□□ 10×12.5 0.12 1120 13 5250 1680 RHT1A561MDN1□□ FP-010RE561M-HT□□ 270 10×12.5 0.12 864 16 4750 1520 RHT1C271MDN1□□ FP-016RE271M-HT□□ 330 10×12.5 0.12 1056 16 4750 1520 RHT1C331MDN1□□ FP-016RE331M-HT□□ 23.0 150 10×12.5 0.12 600 20 4350 1390 RHT1D151MDN1□□ FP-020RE151M-HT□□ 40.2 100 10×12.5 0.12 700 25 3250 1040 RHT1V101MDN1□□ FP-035RE101M-HT□□ 7.2 11.5 18.4 : At ambient temperature Frequency Characteristics (The frequency characteristics are typical and not a guaranteed value.) 16V 330µF Impedance 16V 330µF Frequency (kHz) Frequency (kHz) Taping specifications are given in page 26, 27. Please refer to page 3 for the minimum order quantity. CAT.8100D