RENESAS BCR16PM-12LC

BCR16PM-12LC
Triac
Medium Power Use
REJ03G1262-0200
Rev.2.00
Jul 28, 2006
Features
•
•
•
•
• The product guaranteed maximum junction
temperature 150°C.
• Insulated Type
• Planar Passivation Type
IT (RMS) : 16 A
VDRM : 600 V
IFGTI, IRGTI, IRGTIII : 50 mA
Viso : 1500 V
Outline
RENESAS Package code: PRSS0003AA-B
(Package name: TO-220F(2) )
2
1. T1 Terminal
2. T2 Terminal
3. Gate Terminal
3
1
1
2
3
Applications
Motor control, heater control
Maximum Ratings
Parameter
Repetitive peak off-state voltageNote1
Non-repetitive peak off-state voltageNote1
Rev.2.00
Jul 28, 2006
page 1 of 7
Symbol
VDRM
VDSM
Voltage class
12
600
700
Unit
V
V
BCR16PM-12LC
Parameter
RMS on-state current
Symbol
IT (RMS)
Ratings
16
Unit
A
Surge on-state current
ITSM
96
A
I2 t
38
A2s
PGM
PG (AV)
VGM
IGM
Tj
Tstg
—
Viso
5
0.5
10
2
– 40 to +150
– 40 to +150
2.0
1500
W
W
V
A
°C
°C
g
V
I2t for fusing
Peak gate power dissipation
Average gate power dissipation
Peak gate voltage
Peak gate current
Junction temperature
Storage temperature
Mass
Isolation voltage
Conditions
Commercial frequency, sine full wave
360° conduction, Tc = 60°C
60Hz sinewave 1 full cycle, peak value,
non-repetitive
Value corresponding to 1 cycle of half
wave 60Hz, surge on-state current
Typical value
Ta = 25°C, AC 1 minute,
T1·T2·G terminal to case
Notes: 1. Gate open.
Electrical Characteristics
Parameter
Repetitive peak off-state current
On-state voltage
Symbol
IDRM
VTM
Min.
—
—
Typ.
—
—
Max.
2.0
1.75
Unit
mA
V
Test conditions
Tj = 125°C, VDRM applied
Tc = 25°C, ITM = 25 A,
Instantaneous measurement
Gate trigger voltageNote2
Ι
ΙΙ
ΙΙΙ
VFGTΙ
VRGTΙ
VRGTΙΙΙ
—
—
—
—
—
—
1.5
1.5
1.5
V
V
V
Tj = 25°C, VD = 6 V, RL = 6 Ω,
RG = 330 Ω
Gate trigger currentNote2
Ι
ΙΙ
ΙΙΙ
IFGTΙ
IRGTΙ
IRGTΙΙΙ
—
—
—
—
—
—
50
50
50
mA
mA
mA
Tj = 25°C, VD = 6 V, RL = 6 Ω,
RG = 330 Ω
VGD
Rth (j-c)
0.2
—
—
—
—
4.1
V
°C/W
Gate non-trigger voltage
Thermal resistance
Tj = 125°C, VD = 1/2 VDRM
Junction to caseNote3
(dv/dt)c
10
—
—
V/µs
Tj = 125°C
Critical-rate of rise of off-state
Note4
commutating voltage
Notes: 2. Measurement using the gate trigger characteristics measurement circuit.
3. The contact thermal resistance Rth (c-f) in case of greasing is 0.5°C/W.
4. Test conditions of the critical-rate of rise of off-state commutating voltage is shown in the table below.
Test conditions
1. Junction temperature
Tj = 125°C
2. Rate of decay of on-state commutating current
(di/dt)c = – 8 A/ms
3. Peak off-state voltage
VD = 400 V
Rev.2.00
Jul 28, 2006
page 2 of 7
Commutating voltage and current waveforms
(inductive load)
Supply Voltage
Time
Main Current
(di/dt)c
Time
Main Voltage
(dv/dt)c
Time
VD
BCR16PM-12LC
Performance Curves
Maximum On-State Characteristics
Rated Surge On-State Current
10
7 Tj = 25°C
5
3
2
120
Surge On-State Current (A)
On-State Current (A)
2
101
7
5
3
2
0
10
7
5
3
2
10
–1
2 3
5 7 10
1
2 3
5 7 10
VGM = 10 V
PGM = 5 W
VGT = 1.5 V
PG(AV)
= 0.5 W
IGM = 2 A
0
10
7
5
3
2
IFGT I
IRGT I
IRGT III
Gate Trigger Current (Tj = t°C)
× 100 (%)
Gate Trigger Current (Tj = 25°C)
Gate Trigger Current vs.
Junction Temperature
103
7
5
2
Typical Example
IRGTIII
3
2
102
7
5
IFGTI
3
2
IRGTI
101
–60 –40–20 0 20 40 60 80 100120 140160
Gate Current (mA)
Junction Temperature (°C)
Gate Trigger Voltage vs.
Junction Temperature
Maximum Transient Thermal Impedance
Characteristics (Junction to case)
3
10
7
5
Typical Example
3
2
102
7
5
3
2
1
10
–60 –40–20 0 20 40 60 80 100120140160
Junction Temperature (°C)
Jul 28, 2006
page 3 of 7
Transient Thermal Impedance (°C/W)
Gate Voltage (V)
20
Gate Characteristics (I, II and III)
VGD = 0.2 V
Gate Trigger Voltage (Tj = t°C)
× 100 (%)
Gate Trigger Voltage (Tj = 25°C)
40
Conduction Time (Cycles at 60Hz)
10–1 1
10 2 3 5 7102 2 3 5 7103 2 3 5 7104
Rev.2.00
60
On-State Voltage (V)
1
10
7
5
3
2
80
0 0
10
0.6 1.0 1.4 1.8 2.2 2.6 3.0 3.4 3.8
102
7
5
3
2
100
10
5.0
2
2 3 5 7103 2 3 5 7
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0 –1
10 2 3 5 7100 2 3 5 7101 2 3 5 7102
Conduction Time (Cycles at 60 Hz)
BCR16PM-12LC
10
7
5
3
2
102
7
5
3
2
101
7
5
3
2
100
7
5
3
2
10–1 1
2
3
On-State Power Dissipation (W)
20
360° Conduction
Resistive,
15 inductive loads
10
5
0
0
5
2
4
6
8 10 12 14 16 18 20
Conduction Time (Cycles at 60Hz)
RMS On-State Current (A)
Allowable Case Temperature vs.
RMS On-State Current
Allowable Ambient Temperature vs.
RMS On-State Current
Curves apply regardless
of conduction angle
140
120
100
80
60
40
360° Conduction
20 Resistive,
inductive loads
2
4
6
160
Ambient Temperature (°C)
Case Temperature (°C)
4
10 2 3 5 710 2 3 5 710 2 3 5 710 2 3 5 710
0
0
120
120 × 120 × t2.3
100
100 × 100 × t2.3
80
60 × 60 × t2.3
60 Curves apply
regardless of
40 conduction angle
Resistive,
20 inductive loads
0
0
8 10 12 14 16 18 20
All fins are black painted
aluminum and greased
140
Natural convection
2
4
6
8 10 12 14 16 18 20
RMS On-State Current (A)
RMS On-State Current (A)
Allowable Ambient Temperature vs.
RMS On-State Current
Repetitive Peak Off-State Current vs.
Junction Temperature
160
Ambient Temperature (°C)
25
No Fins
160
Natural convection
No Fins
Curves apply regardless
of conduction angle
Resistive, inductive loads
140
120
100
80
60
40
20
0
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0
RMS On-State Current (A)
Rev.2.00
Maximum On-State Power Dissipation
3
Jul 28, 2006
page 4 of 7
Repetitive Peak Off-State Current (Tj = t°C)
× 100 (%)
Repetitive Peak Off-State Current (Tj = 25°C)
Transient Thermal Impedance (°C/W)
Maximum Transient Thermal Impedance
Characteristics (Junction to ambient)
106
7
5
3
2
105
7
5
3
2
104
7
5
3
2
103
7
5
3
2
102
Typical Example
–60 –40–20 0 20 40 60 80 100120140160
Junction Temperature (°C)
BCR16PM-12LC
103
7
5
Latching Current (mA)
Typical Example
3
2
102
7
5
3
2
101
–60 –40–20 0 20 40 60 80 100 120140 160
103
7
5
3
2
Distribution
T2+, G–
Typical Example
102
7
5
3
2
101
7 T2+, G+
5 Typical Example
3
2
10
T2–, G–
Typical Example
0
–60 –40 –20 0 20 40 60 80 100 120 140160
Junction Temperature (°C)
Breakover Voltage vs.
Junction Temperature
Breakover Voltage vs. Rate of
Rise of Off-State Voltage (Tj = 125°C)
160
Typical Example
140
120
100
80
60
40
20
0
–60 –40–20 0 20 40 60 80 100120 140160
Breakover Voltage (dv/dt = xV/µs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/µs)
Junction Temperature (°C)
160
Typical Example
Tj = 125°C
140
120
III Quadrant
100
80
I Quadrant
60
40
20
0 1
2
3
4
10 2 3 5 710 2 3 5 710 2 3 5 710
Junction Temperature (°C)
Rate of Rise of Off-State Voltage (V/µs)
Breakover Voltage vs. Rate of
Rise of Off-State Voltage (Tj = 150°C)
Commutation Characteristics (Tj = 125°C)
160
140
Typical Example
Tj = 150°C
120
III Quadrant
100
80
60
I Quadrant
40
20
0 1
10 2 3 5 7102 2 3 5 7103 2 3 5 7104
Rate of Rise of Off-State Voltage (V/µs)
Rev.2.00
Latching Current vs.
Junction Temperature
Jul 28, 2006
page 5 of 7
Critical Rate of Rise of Off-State
Commutating Voltage (V/µs)
Breakover Voltage (dv/dt = xV/µs)
× 100 (%)
Breakover Voltage (dv/dt = 1V/µs)
Breakover Voltage (Tj = t°C)
× 100 (%)
Breakover Voltage (Tj = 25°C)
Holding Current (Tj = t°C)
× 100 (%)
Holding Current (Tj = 25°C)
Holding Current vs.
Junction Temperature
7
5
3
2
Time
Main Voltage
(dv/dt)c
VD
Main Current
(di/dt)c
IT
τ
Time
III Quadrant
1
10
7
5
I Quadrant
Minimum
Characteristics
Value
3
2 Typical Example
0
Tj = 125°C, IT = 4 A
τ = 500 µs, VD = 200 V
f = 3 Hz
10
7 0
10
2 3
5 7 101
2 3
5 7 102
Rate of Decay of On-State
Commutating Current (A/ms)
BCR16PM-12LC
Gate Trigger Current vs.
Gate Current Pulse Width
7
5 Typical Example
Tj = 150°C
3 IT = 4 A
2 τ = 500 µs
VD = 200 V
1 f = 3 Hz
Gate Trigger Current (tw)
× 100 (%)
Gate Trigger Current (DC)
Critical Rate of Rise of Off-State
Commutating Voltage (V/µs)
Commutation Characteristics (Tj = 150°C)
Time
Main Voltage
(dv/dt)c
VD
Main Current
(di/dt)c
IT
τ
Time
III Quadrant
10
7
5
I Quadrant
3
2
100
7 0
10
5 7 101
2 3
2 3
5 7 102
Gate Trigger Characteristics Test Circuits
6Ω
A
6V
330 Ω
V
Test Procedure I
A
V
330 Ω
Test Procedure III
Rev.2.00
Jul 28, 2006
V
Test Procedure II
6Ω
6V
A
6V
page 6 of 7
Typical Example
IRGT III
IRGT I
3
2
IFGT I
102
7
5
3
2
101 0
10
2 3
5 7 101
2 3
5 7 102
Gate Current Pulse Width (µs)
Rate of Decay of On-State
Commutating Current (A/ms)
6Ω
103
7
5
330 Ω
BCR16PM-12LC
Package Dimensions
JEITA Package Code
SC-67
Package Name
TO-220F(2)
RENESAS Code
PRSS0003AA-B
Previous Code

MASS[Typ.]
2.0g
Unit: mm
10.5Max
2.8
17
8.5
5.0
1.2
5.2
φ3.2 ± 0.2
13.5Min
3.6
1.3Max
0.8
2.54
0.5
2.6
4.5
2.54
Order Code
Lead form
Standard packing
Quantity
Standard order code
Straight type
Vinyl sack
100 Type name
Lead form
Plastic Magazine (Tube)
50 Type name – Lead forming code
Note : Please confirm the specification about the shipping in detail.
Rev.2.00
Jul 28, 2006
page 7 of 7
Standard order
code example
BCR16PM-12LC
BCR16PM-12LC-A8
Sales Strategic Planning Div.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary
circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
http://www.renesas.com
RENESAS SALES OFFICES
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology (Shanghai) Co., Ltd.
Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120
Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
Renesas Technology Korea Co., Ltd.
Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea
Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145
Renesas Technology Malaysia Sdn. Bhd
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: <603> 7955-9390, Fax: <603> 7955-9510
© 2006. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .6.0