RED20W SERIES DC-DC CONVERTER 4 : 1 ULTRA WIDE INPUT RANGE UP TO 20Watts FEATURES APPLICATIONS • 1600VDC INPUT TO OUTPUT ISOLATION • STANDARD 2.00 X 1.00 X 0.40 INCH • SIX-SIDED CONTINUOUS SHIELD • UL60950-1, EN60950-1, IEC60950-1, & EN50155 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH 1600VDC ISOLATION REMOTE CONTROL UVP OCP • RAILWAY SYSTEM • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT SCP LOW STANDBY POWER OVP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25℃ otherwise noted Model Number Input Range Output Voltage Output Current @Full Load Input Current @ No Load Efficiency Maximum Capacitor Load (1) VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 43 ~ 160 43 ~ 160 43 ~ 160 43 ~ 160 43 ~ 160 43 ~ 160 VDC 3.3 5 12 15 ±12 ±15 3.3 5 12 15 ±12 ±15 3.3 5 12 15 ±12 ±15 mA 4500 4000 1670 1330 ±833 ±667 4500 4000 1670 1330 ±833 ±667 4500 4000 1670 1330 ±833 ±667 mA 6 6 6 6 6 6 4 4 4 4 4 4 3 3 3 3 3 3 % 85 88 89 88 88 89 85 88 89 89 88 89 85 87 88 88 88 89 µF 7000 5000 850 700 ±500 ±350 7000 5000 850 700 ±500 ±350 7000 5000 850 700 ±500 ±350 RED20-24S3P3W RED20-24S05W RED20-24S12W RED20-24S15W RED20-24D12W RED20-24D15W RED20-48S3P3W RED20-48S05W RED20-48S12W RED20-48S15W RED20-48D12W RED20-48D15W RED20-110S3P3W RED20-110S05W RED20-110S12W RED20-110S15W RED20-110D12W RED20-110D15W PART NUMBER STRUCTURE RED20 - 48 Series Name Input Voltage (VDC) 24: 9~36 48: 18~75 110: 43~160 S Output Quantity S: Single D: Dual 1 05 Output Voltage (VDC) 3P3: 3.3 05: 5 12: 12 15: 15 12: ±12 15: ±15 W Input Range 4:1 : A: B: C: D: E: A HS Option Assembly Option Negative logic remote ON/OFF(Standard) Positive logic remote ON/OFF Without Ctrl pin Negative logic remote ON/OFF without Trim pin Without Ctrl & Trim pin Positive logic remote ON/OFF without Trim pin www.PDUKE.com : None HS: Heat-sink HC: Heat-sink with Clamp 2015/6/9 RED20W INPUT SPECIFICATIONS Parameter Conditions Operating input voltage range 24Vin(nom) 48Vin(nom) 110Vin(nom) Input reflected ripple current Start up voltage 24Vin(nom) 48Vin(nom) 110Vin(nom) 24Vin(nom) 48Vin(nom) 110Vin(nom) Power up Remote ON/OFF 24Vin(nom) 48Vin(nom) 110Vin(nom) 24Vin(nom), 48 Vin(nom) 110Vin(nom) Positive logic DC-DC ON (Option) DC-DC OFF Negative logic DC-DC ON (Standard) DC-DC OFF Input current of Ctrl pin Remote off input current Shutdown voltage Start up time Constant resistive load Input surge voltage 100 ms, max. Input filter Remote ON/OFF Referred to –Vin pin OUTPUT SPECIFICATIONS Parameter Conditions Voltage accuracy Line regulation Low Line to High Line at Full Load Load regulation No Load to Full Load 10% Load to 90% Load Cross regulation Voltage adjustability Ripple and noise Temperature coefficient Transient response recovery time Over voltage protection Over load protection Short circuit protection Asymmetrical load 25%/100% FL Single output 20MHz bandwidth With a 1µF/50V X7R MLCC Max. Unit 24 48 110 30 36 75 160 VDC -0.5 Min. Isolation resistance Isolation capacitance Switching frequency Safety approvals 500VDC VDC 30 30 50 100 170 Common Chock Pi type Open or 3 ~ 15VDC Short or 0 ~ 1.2VDC Short or 0 ~ 1.2VDC Open or 3 ~ 15VDC +1.0 2.5 Typ. -1.0 -0.2 -0.5 -0.2 -1.0 -0.1 -0.8 -5.0 -10 VDC mA mA Unit +1.0 +0.2 +0.5 +0.2 +1.0 +0.1 +0.8 +5.0 +10 % 75 100 % % % % mVp-p +0.02 3.7 5.6 13.5 16.8 ms Max. 250 % of Iout rated VDC 8 16 40 3.3Vout, 5Vout 12Vout, 15Vout 3.3Vout 5Vout 12Vout 15Vout 1 minute mAp-p 9 18 43 -0.02 Isolation voltage 2 Typ. 9 18 43 25% load step change GENERAL SPECIFICATIONS Parameter Case material Base material Potting material Weight MTBF Single Dual Single Dual Single Dual Dual Min. 5.4 7.0 19.6 20.5 %/℃ µs VDC 150 % Continuous, automatics recovery Conditions Input to Output Input (Output) to Case Min. 1600 1600 1 297 MIL-HDBK-217F, Full load www.PDUKE.com Typ. Max. Unit VDC GΩ pF 330 kHz UL60950-1 EN60950-1 IEC60950-1 EN50155 Nickel-coated copper FR4 PCB Silicone (UL94 V-0) 30g (1.06oz) 1.523 x 106 hrs 3000 363 2015/6/9 RED20W ENVIRONMENTAL SPECIFICATIONS Parameter Operating ambient temperature Maximum case temperature Storage temperature range Thermal impedance Conditions Min. With derating Typ. -40 Without heat-sink With heat-sink Thermal shock Shock Vibration Relative humidity Unit +101 +105 +125 -55 Vertical direction by natural convection (20LFM) Max. 12 10 /W MIL-STD-810F EN61373, MIL-STD-810F EN61373, MIL-STD-810F 5% to 95% RH EMC SPECIFICATIONS Parameter EMI (2) ESD Radiated immunity Fast transient (3) Surge (3) Conducted immunity Conditions EN55022, EN55011 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level Air ± 8kV and Contact ± 6kV 10 V/m ±2kV ±2kV 10 Vr.m.s Class A, Class B Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: 1. 2. 3. Test by minimum input and constant resistive load. The 24VDC & 48VDC input standard modules meet EN55022 & EN55011 Class B without external components, 110VDC input meet EN55022 Class A without external components and meet Class B with external components. For further information, please contact with P-DUKE. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: 24VDC & 48VDC input: Nippon chemi-con KY series, 220µF/100V. The filter capacitor Power Mate suggest::110VDC input: Rubycon BXF series, 100µF/250V. CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE 3 RED20-48S05W Derating Curve RED20-48S05W Derating Curve With Heat-sink RED20-48S05W Efficiency vs. Input Voltage RED20-48S05W Efficiency vs. Output Load www.PDUKE.com 2015/6/9 RED20W MECHANICAL DRAWING PIN CONNECTION PIN 1 2 3 4 5 6 SINGLE +Vin -Vin +Vout Trim -Vout Ctrl DUAL +Vin -Vin +Vout Common -Vout Ctrl EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 5 4 RU 4 RD 3 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 4 www.PDUKE.com 2015/6/9