FEC60 FEC60 SERIES DC-DC CONVERTER 2:1 WIDE INPUT RANGE UP TO 60Watts FEATURES APPLICATIONS • NO MINIMUM LOAD REQUIRED • 1600VDC INPUT TO OUTPUT ISOLATION • STANDARD 2.00 X 2.00 X 0.40 INCH • SIX-SIDED CONTINUOUS SHIELD • UL60950-1, EN60950-1, & IEC60950-1 SAFETY APPROVALS • CE MARKED • COMPLIANT TO RoHS II & REACH 1600VDC ISOLATION REMOTE CONTROL UVP OCP • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT SCP OVP OTP TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25 Model Number FEC60-24S3P3 FEC60-24S05 FEC60-24S12 FEC60-24S15 FEC60-24S24 FEC60-48S3P3 FEC60-48S05 FEC60-48S12 FEC60-48S15 FEC60-48S24 otherwise noted Input Range Output Voltage Output Current @Full Load Input Current @ No Load Efficiency Maximum Capacitor Load (1) VDC 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 VDC 3.3 5 12 15 24 3.3 5 12 15 24 A 14 12 5 4 2.5 14 12 5 4 2.5 mA 100 130 50 50 50 80 90 30 30 30 % 89 90 90 90 89 89 91 90 90 90 µF 36000 20400 3550 2300 885 36000 20400 3550 2300 885 PART NUMBER STRUCTURE FEC60 - 48 Series Name 1 Input Voltage (VDC) 24: 18~36 48: 36~75 S Output Quantity S: Single 05 Output Voltage (VDC) 3P3: 3.3 05: 5 12: 12 15: 15 24: 24 - N HS Remote Control Option Assembly Option : Positive logic N: Negative logic www.PDUKE.com : No assembly HS: Heat-sink HC: Heat-sink with Clamp 2015/2/26 FEC60 INPUT SPECIFICATIONS Parameter Conditions 24Vin(nom) 48Vin(nom) Operating input voltage range Input reflected ripple current Start-up voltage Start up time Constant resistive load Input surge voltage 100 ms, max. Input filter Remote ON/OFF Referred to –Vin pin OUTPUT SPECIFICATIONS Parameter Measured by 20MHz bandwidth 2 -0.5 Min. 24Vout Others 3.3Vout, 5Vout 12Vout, 15Vout 24Vout Typ. % of Iout rated Conditions Input to Output Input(Output) to Case 500VDC MIL-HDBK-217F, Full load www.PDUKE.com ms VDC mA mA Max. Unit +1.0 +0.2 +0.5 +20 +10 % % % % mVp-p +0.02 250 3.3Vout 5Vout 12Vout 15Vout 24Vout VDC VDC 75 100 200 -0.02 1 minute mAp-p 20 20 50 100 Pi type Open or 3 ~ 12VDC Short or 0 ~ 1.2VDC Short or 0 ~ 1.2VDC Open or 3 ~ 12VDC +1.0 4.0 -1.0 -0.2 -0.5 -10 -10 25% load step change GENERAL SPECIFICATIONS Parameter Case material Base material Potting material Weight MTBF VDC 15 32 Conditions Ripple and noise Case grounding Isolation resistance Isolation capacitance Switching frequency Safety approvals Unit 36 75 17 34 Positive logic DC-DC ON (Standard) DC-DC OFF Negative logic DC-DC ON (Option) DC-DC OFF Input current of Ctrl pin Remote off input current Low Line to High Line at Full Load No Load to Full Load Isolation voltage Max. 24 48 20 24Vin(nom) 48Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 24Vin(nom) 48Vin(nom) Voltage accuracy Line regulation Load regulation Voltage adjustability (2) Over load protection Short circuit protection Typ. 18 36 Nominal input and Full load Shutdown voltage Temperature coefficient Transient response recovery time Over voltage protection Min. %/ µs 3.7 5.6 13.8 16.8 30.0 5.4 7.0 17.5 VDC 20.5 33.0 150 % Continuous, automatics recovery Min. Typ. Max. Unit 1600 VDC 1600 Connect case to –Vin with decoupling Y Cap 1 GΩ 1500 pF 270 300 330 kHz UL60950-1 EN60950-1 IEC60950-1 Nickel-coated copper FR4 PCB Epoxy (UL94 V-0) 60g (2.11oz) 4.089 x 105 hrs 2015/2/26 FEC60 ENVIRONMENTAL SPECIFICATIONS Parameter Conditions Operating ambient temperature Maximum case temperature Over temperature protection Storage temperature range Thermal impedance Min. Without derating With derating Typ. -40 +40 Max. Unit +40 +110 +110 +120 -55 Vertical direction by natural convection (20LFM) Without heat-sink With heat-sink +125 10.5 8.4 /W Thermal shock Vibration Relative humidity MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC SPECIFICATIONS Parameter EMI (3) ESD Radiated immunity Fast transient (4) Surge (4) Conducted immunity Conditions EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level Air ± 8kV and Contact ± 6kV 10 V/m ± 2kV ± 1kV 10 Vr.m.s Class A, Class B Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: 1. 2. 3. 4. Test by minimum input and constant resistive load. 24Vout maximum output deviation is +20%,-10% inclusive of remote sense and trim. Others maximum output deviation is 10% inclusive of remote sense and trim. If remote sense is not being used, the +Sense should be connected to its corresponding +Vout and likewise the -Sense should be connected to its corresponding -Vout. The standard modules meet EN55022 Class A and Class B with external components. For further information, please contact with P-DUKE. An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The filter capacitor Power Mate suggest: Nippon chemi-con KY series, 220µF/100V. CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE 3 FEC60-48S05 Derating Curve FEC60-48S05 Derating Curve With Heat-sink FEC60-48S05 Efficiency vs. Input Voltage FEC60-48S05 Efficiency vs. Output Load www.PDUKE.com 2015/2/26 FEC60 MECHANICAL DRAWING PIN CONNECTION PIN 1 2 3 4 5 6 7 8 SINGLE +Vin -Vin Ctrl -Sense (2) +Sense (2) +Vout -Vout Trim EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. TRIM UP TRIM DOWN 4 8 RU 8 RD 5 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 4 www.PDUKE.com 2015/2/26