FED40 FED40 SERIES DC-DC CONVERTER 2:1 WIDE INPUT RANGE UP TO 40 Watts FEATURES APPLICATIONS • NO MINIMUM LOAD REQUIRED • 1600VDC INPUT TO OUTPUT ISOLATION • STANDARD 2.00 X 1.00 X 0.40 INCH • SIX-SIDED CONTINUOUS SHIELD • SAFETY MEETS UL60950-1, EN60950-1, IEC60950-1, & EN50155 • CE MARKED • COMPLIANT TO RoHS II & REACH 1600VDC ISOLATION REMOTE CONTROL UVP • WIRELESS NETWORK • TELECOM/DATACOM • INDUSTRY CONTROL SYSTEM • DISTRIBUTED POWER ARCHITECTURES • SEMICONDUCTOR EQUIPMENT OCP SCP OVP OTP LOW STANDBY POWER TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25℃ otherwise noted Model Number FED40-12S3P3 FED40-12S05 FED40-12S12 FED40-12S15 FED40-12S24 FED40-12D12 FED40-12D15 FED40-12D24 FED40-24S3P3 FED40-24S05 FED40-24S12 FED40-24S15 FED40-24S24 FED40-24D12 FED40-24D15 FED40-24D24 FED40-48S3P3 FED40-48S05 FED40-48S12 FED40-48S15 FED40-48S24 FED40-48D12 FED40-48D15 FED40-48D24 Input Range Output Voltage Output Current @Full Load Input Current @ No Load Efficiency Maximum Capacitor Load (1) VDC 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 9 ~ 18 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 18 ~ 36 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 36 ~ 75 VDC 3.3 5 12 15 24 ±12 ±15 ±24 3.3 5 12 15 24 ±12 ±15 ±24 3.3 5 12 15 24 ±12 ±15 ±24 mA 10000 8000 3333 2666 1666 ±1666 ±1333 ±833 10000 8000 3333 2666 1666 ±1666 ±1333 ±833 10000 8000 3333 2666 1666 ±1666 ±1333 ±833 mA 20 20 20 20 20 20 20 20 15 15 15 15 15 15 15 15 10 10 10 10 10 10 10 10 % 90 91 91 91 91 90 91 91 91 92 92 92 91 90 91 91 91 92 92 92 92 91 91 90 µF 26600 20000 3900 2600 1300 ± 2600 ± 1600 ±650 26600 20000 3900 2600 1300 ± 2600 ± 1600 ±650 26600 20000 3900 2600 1300 ± 2600 ± 1600 ±650 PART NUMBER STRUCTURE FED40 Series Name 48 Input Voltage (VDC) 12: 9~18 24: 18~36 48: 36~75 S Output Quantity S: Single D: Dual 1 05 Output Voltage (VDC) 3P3: 3.3 05: 5 12: 12 15: 15 24: 24 12: ±12 15: ±15 24: ±24 - N HS Remote Control options Heat-sink : Positive logic N: Negative logic www.PDUKE.com : No Heat-sink HS: Heat-sink HC: Heat-sink with Clamp 2014/4/30 FED40 INPUT SPECIFICATIONS Parameter Conditions 12Vin(nom) 24Vin(nom) 48Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) 12Vin(nom) 24Vin(nom) 48Vin(nom) Power up Remote ON/OFF 12Vin(nom) 24Vin(nom) 48Vin(nom) Operating input voltage range Start-up voltage Shutdown voltage Start up time Constant resistive load Input surge voltage 1 second, max. Input filter Remote ON/OFF Referred to –Vin pin OUTPUT SPECIFICATIONS Parameter Voltage accuracy Line regulation Load regulation Positive logic DC-DC ON (Standard) DC-DC OFF DC-DC ON Negative logic (Option) DC-DC OFF Input current of Ctrl pin Remote off input current Conditions Low Line to High Line at Full Load No Load to Full Load Cross regulation Voltage adjustability Asymmetrical load 25%/100% FL Single output Ripple and noise Measured by 20MHz bandwidth With a 0.1µF/50V X7R MLCC Temperature coefficient Transient response recovery time Over voltage protection Over load protection Short circuit protection 3.3Vout 5Vout 12Vout 15Vout 24Vout % of Iout rated; Hiccup mode Isolation voltage 1 minute Isolation resistance Isolation capacitance Switching frequency Safety meets 500VDC 2 Typ. Max. 9 18 36 12 24 48 18 36 75 9 18 36 8 16 32 60 60 -0.5 Min. Conditions Input to Output Input (Output) to Case Typ. -1.0 -0.2 -0.5 -1.0 -5.0 -10 -10 75 100 150 www.PDUKE.com VDC VDC VDC ms Max. Unit +1.0 +0.2 +0.5 +1.0 +5.0 +10 +20 100 125 200 +0.02 % % % % % mVp-p ℃ %/ 250 µs 3.9 6.2 15 VDC 20 30 150 % Continuous, automatics recovery Min. Typ. 1600 1600 1 225 MIL-HDBK-217F, Full load. Unit 25 50 VDC 100 Pi type Open or 3 ~ 12VDC Short or 0 ~ 1.2VDC Short or 0 ~ 1.2VDC Open or 3 ~ 12VDC 0.5 mA 3 mA -0.02 25% load step change Zener diode clamp GENERAL SPECIFICATIONS Parameter Case material Base material Potting material Weight MTBF Single Dual Dual 3.3Vout, 5Vout, 12Vout 15Vout, 24Vout 3.3Vout, 5Vout 12Vout, 15Vout 24Vout Min. Max. Unit VDC 250 GΩ pF kHz UL60950-1 EN60950-1 IEC60950-1 Copper FR4 PCB Silicone (UL94 V-0) 32g (1.13oz) 1.066 x 106 hrs 1500 275 2014/4/30 FED40 ENVIRONMENTAL SPECIFICATIONS Parameter Operating ambient temperature Maximum case temperature Over temperature protection Storage temperature range Thermal impedance Conditions Min. Typ. -40 Max. +85 +105 +115 -55 Vertical direction by natural convection (20LFM) Without Heat-sink With Heat-sink +125 10.8 10.3 Thermal shock Vibration Relative humidity Unit ℃ ℃ ℃ ℃ ℃/W MIL-STD-810F MIL-STD-810F 5% to 95% RH EMC SPECIFICATIONS Parameter EMI (2) ESD Radiated immunity Fast transient (3) Surge (3) Conducted immunity Conditions EN55022 EN61000-4-2 EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 Level Air ± 8kV and Contact ± 6kV 20 V/m ± 2kV ± 2kV 10 Vr.m.s Class A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: 1. 2. 3. Test by minimum input and constant resistive load. The standard modules meets EMI Class A or Class B with external components. For further information, please contact with P-DUKE. The external input components are required required if the module has to meet EN61000-4-4, EN61000-4-5. The FED40-12 recommended an aluminum electrolytic capacitor (Nippon chemi-con KY series, 220µF/100V) and a TVS (SMDJ58A, 58V, 3000Watt peak pulse power) to connect in parallel. The FED40-24 recommended an aluminum electrolytic capacitor (Nippon chemi-con KY series, 220µF/100V) and a TVS (SMDJ64A, 64V, 3000Watt peak pulse power) to connect in parallel. The FED40-48 recommended an aluminum electrolytic capacitor (Nippon chemi-con KY series, 220µF/100V) and a TVS (SMDJ120A,120V, 3000Watt peak pulse power) to connect in parallel. CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE FED40-48S05 Derating Curve FED40-48S05 Derating Curve with Heat-sink FED40-48S05 Efficiency VS Input Voltage FED40-48S05 Efficiency VS Output Load MECHANICAL DRAWING 3 www.PDUKE.com 2014/4/30 FED40 PIN CONNECTION PIN SINGLE 1 + Vin 2 - Vin 3 Ctrl 4 + Vout 5 - Vout 6 Trim DUAL + Vin - Vin Ctrl + Vout Common - Vout EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) 4 www.PDUKE.com 2014/4/30