Datasheet R2A20169NP/SA/SP 8-bit 12ch D/A Converter with Buffer Amplifiers R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Description The R2A20169 is an integrated circuit semiconductor of CMOS structure with 12 channels of built in D/A unnecessary and enabling configuration of a system with few component parts. Serial data transfer type input can easily be used through a combination of three lines: DI, CLK, and LD. Outputs incorporate buffer op-amps that have a drive capacity of 1 mA or above for both sink source, and can operate over the entire voltage range from almost ground to Vcc ( 0 to 5V ), making peripheral elements unnecessary and enabling configuration of a system with few component parts. Very small QFN package is added to lineup. It is suitable for a small mounting and reduces the mounting area. Features · Guarantee Nonlinearity error : +/-1.0LSB, Differential nonlinearity error : +/-0.7LSB · Data transfer format: 12-bit serial data input type by 3 wire ( DI, SCK, LD ) · Output buffer op-amps: Operable over entire voltage range from almost ground to Vcc ( 0 to 5V ) · High output current capacity: +/-1mA or Higher · Very small size package line-up: QFN-20 (pin pitch: 0.5mm), TSSOP-20 (pin pitch 0.65mm) Application · Conversion from digital data to analog control data for home-use and industrial equipment. Block Diagram Number for TSSOP/SOP package Number for QFN package Ao12 Vcc Ao11 GND Ao2 Ao1 DI CLK LD DO 20 19 18 17 16 15 14 13 12 11 18 17 16 15 14 13 12 11 10 9 D/A D/A Power on reset 8-bit latch 8-bit latch 12-bit shift register D0 1 2 3 4 5 6 7 8-bit upper segment R-2R D/A converter 8 9 10 11 D/A Channel decoder 8 8-bit latch 8-bit latch 12 8-bit latch 8-bit latch 8-bit latch 8-bit latch 8-bit latch 8-bit latch 8-bit latch 8-bit latch 8-bit upper segment R-2R D/A converter D/A D/A D/A D/A D/A D/A D/A 19 20 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 9 10 VrefL Ao3 Ao4 Ao5 Ao6 Ao7 Ao8 Ao9 Ao10 VrefU R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Page 1 of 9 Datasheet R2A20169NP/SA/SP Pin Arrangement R2A20169SP/SA (Top view) 16 Ao1 17 Ao2 18 GND 19 VrefL 20 Ao3 R2A20169NP (Top view) R2A20169NP Ao5 2 Ao6 3 Ao7 4 14 CLK 13 LD 12 Do Ao11 10 Vcc 9 VrefU 8 11 Ao12 Ao10 7 Ao5 4 Ao6 5 Ao7 6 Ao8 7 Ao9 8 Ao8 5 Ao9 6 Ao4 3 Outline: PWQN0020KB-A [NP] 19 Ao2 R2A20169SP/SA 15 DI Ao4 1 20 GND VrefL 1 Ao3 2 18 Ao1 17 DI 16 CLK 15 LD 14 Do 13 Ao12 Ao10 9 12 Ao11 VrefU 10 11 Vcc Outline: PRSP0020DD-B[SP] PTSP0020JB-A [SA] Pin Description Pin No. Pin Name [QFN] [TSSOP /SOP] 15 17 DI 12 14 Do 14 16 CLK 13 15 LD 16 18 Ao1 17 19 Ao2 20 2 Ao3 1 3 Ao4 2 4 Ao5 3 5 Ao6 4 6 Ao7 5 7 Ao8 6 8 Ao9 7 9 Ao10 10 12 Ao11 11 13 Ao12 Function Serial data input terminal. (Input serial data with a 12-bit data length.) Serial data output terminal (Data is sequentially output from the MSB bit.) Serial clock input terminal (Input signal from DI terminal is input to 12-bit shift register at rise of serial clock.) Load terminal (When High level is input to LD terminal, value in 12-bit shift register is loaded into decoder and 8-bit latch.) 8-bit resolution D/A converter output terminals (After power-on, all channels are reset and DAC data 00h is output.) 9 11 Vcc Power supply terminal 18 20 GND GND terminal 8 10 VrefU D/A converter upper reference voltage input terminal 19 1 VrefL D/A converter lower reference voltage input terminal R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Page 2 of 9 Datasheet R2A20169NP/SA/SP Absolute Maximum Ratings (Ta= +25deg unless otherwise noted) Item Symbol Conditions Ratings Unit Supply voltage Vcc -0.3 to +6.5 V D/A converter upper reference voltage VrefU -0.3 to +6.5 V D/A converter lower reference voltage VrefL -0.3 to +6.5 V Buffer amplifier output current IAO -2.0 to +2.0 mA Continuous Input voltage Vin -0.3 to Vcc+0.3 <+6.5 V Output voltage Vo -0.3 to Vcc+0.3 <+6.5 V Power dissipation Pd Ta= +85deg 290(NP) / 150(SA) / 300(SP) mW Thermal derating factor K theta Ta> +25deg 7.25(NP) / 3.75(SA) / 7.5(SP) mW/deg Operating temperature Topr -30 to +85 deg Storage temperature Tstg -40 to +125 deg Electrical Characteristics « Digital Part » ( Vcc, VrefU = +5V +/-10%, Vcc>VrefU, GND,VrefL =0V, Ta= -30 to +85deg, Unless otherwise noted ) Limits Item Symbol Test conditions Unit Min Typ Max 2.7 5.0 5.5 V Supply voltage Vcc Supply current Icc CLK = 1MHz, Vcc =5V, IAO =0µA - 0.6 1.8 mA Input leak current IILK VIN = 0 to Vcc -10 - 10 µA Input low voltage VIL - - 0.2Vcc V 4.0V < Vcc 0.5Vcc - - V Input high voltage VIH Vcc < 4.0V 0.8Vcc - - V 4.0V < Vcc, IOL =2.0 mA - - 0.4 V Vcc < 4.0V, IOL =1.5 mA - - 0.4 V Output low voltage VOL Output high voltage VOH IOH = -400 µA Vcc – 0.4 - - V Supply voltage rise time *1 trVcc Vcc = 0 ® 2.7V 100 - - µs VccPOR Vcc = 0 ® 2.7V - 1.5 1.9 V tPOR Vcc < 0.1V 1 - - ms Internal reset operating voltage *1 Power supply restart interval (Power supply OFF à ON) *1 *1 : When power supply is turned on, internal circuit is initialized by power on reset circuit. But, if re-powered on quickly, initialize is not operate. So, keep the time period of re-powered on (tPOR). trVcc Vcc tPOR (equivalent to trVcc) VccPOR GND Internal Reset signal < 0.1V GND Resetting period R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Resetting period Page 3 of 9 Datasheet R2A20169NP/SA/SP « Analog Part » ( Vcc,VrefU = +5V +/-10%, Vcc>VrefU, GND,VrefL=0V, Ta= -30 to +85deg, unless otherwise noted ) Limits Item Symbol Current dissipation IrefU D/A converter upper reference voltage range *2 VrefU D/A converter lower reference voltage range *2 VrefL Buffer amplifier output voltage range VAO Buffer amplifier output drive range IAO Differential nonlinearity SDL Nonlinearity SL Zero code error SZERO Full scale error SFULL Test conditions Unit Min Typ Max - 1.5 3.0 Vcc ³ 4.5V 3.5 - Vcc Vcc < 4.5V 0.7Vcc - Vcc Vcc ³ 4.5V GND - Vcc-3.5 Vcc < 4.5V GND - 0.3Vcc IAO = +/- 100 µA 0.1 - Vcc – 0.1 V IAO = +/- 500 µA 0.2 - Vcc – 0.2 V Upper side saturation voltage = 0.3V, Lower side saturation voltage = 0.2V -1.0 - 1.0 mA -0.7 - 0.7 LSB -1.0 - 1.0 LSB -2.0 - 2.0 LSB -2.0 - 2.0 LSB VrefU=5V, VrefL=0V, IAO=0µA, Data condition: at maximum current mA V V VrefU = 4.79V, VrefL = 0.95V, Vcc = 5.5V (15mV/LSB), Without load (IAO =0µA) Output capacitive load Co - - 0.1 µF Buffer amplifier output impedance Ro - 5.0 - ohm *2 : The output does not necessary be the value with the reference voltage setting range. The output value is determined by the buffer amplifier output voltage range (VAO). R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Page 4 of 9 Datasheet R2A20169NP/SA/SP AC Characteristics ( Vcc, VrefU = +5V +/-10%, Vcc >VrefU, GND=VrefL = 0V, Ta = -30 to +85deg, unless otherwise noted ) Item Test conditions Symbol Limits Min Typ Max Unit Clock frequency fCLK - 1.0 10 MHz Clock low pulse width tCKL 40 - - ns Clock high pulse width tCKH 40 - - ns Clock rise time tCR - - 200 ns Clock fall time tCF - - 200 ns Data setup time tDCH 4 - - ns Data hold time tCHD 30 - - ns LD setup time tCHL 40 - - ns LD hold time tLDC 40 - - ns LD high pulse width tLDH Data output delay time tDO CL < 100 pF D/A output settling time tLDD Ta=25deg, CL<100pF, VAO: 0.5¬®4.5V, The time until the output becomes the final value of 1/2 LSB. 40 - - ns -10 - 50 ns - - 150 µs Timing Chart tCR tCKH tCF CLK tCKL DI tDCH tCHD tCHL tLDH tLDC LD tLDD D/A output tDo Do output (Note) Timing chart above is a schematic representation of the timing of each signal type. CLK signal input is High or Low regardless, LD signal High input is enabled. R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Page 5 of 9 Datasheet R2A20169NP/SA/SP Digital Data Format Last LSB First MSB D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 Channel select data DAC data Channel select data D8 0 0 0 0 0 0 0 0 1 D9 0 0 0 0 1 1 1 1 0 D10 0 0 1 1 0 0 1 1 0 D11 0 1 0 1 0 1 0 1 0 Chanel Selection Don’t care Ao1 select Ao2 select Ao3 select Ao4 select Ao5 select Ao6 select Ao7 select Ao8 select 1 0 0 1 Ao9 select 1 1 1 1 1 1 0 0 1 1 1 1 1 1 0 0 1 1 0 1 0 1 0 1 Ao10 select Ao11 select Ao12 select Don’t care Don’t care Don’t care D0 D1 D2 D3 D4 D5 D6 D7 D/A Output 0 0 0 0 0 0 0 0 (VrefU – VrefL) / 256 x 1 + VrefL 1 0 0 0 0 0 0 0 (VrefU – VrefL) / 256 x 2 + VrefL 0 1 0 0 0 0 0 0 (VrefU – VrefL) / 256 x 3 + VrefL 1 1 0 0 0 0 0 0 (VrefU – VrefL) / 256 x 4 + VrefL : : : : : : : : : 0 1 1 1 1 1 1 1 (VrefU – VrefL) / 256 x 255 + VrefL 1 1 1 1 1 1 1 1 VrefU DAC data R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Page 6 of 9 Datasheet R2A20169NP/SA/SP Data Timing Chart ( Model ) MSB DI D11 LSB D10 D9 D8 D7 D2 D1 D0 CLK Whether CLK input is “H” or “L”, high level input of LD signal is recognized. LD D/A output Precaution For use · There are three terminals (Vcc, VrefU, VrefL) that should be impressed a constant voltage. When ripple or spike noise is input to this terminal, there is fear that the accuracy of D/A conversion becomes lower and this IC malfunction. So, when use this IC, please connect capacitor between these terminals (Vcc, VrefU, VrefL) and GND for stable D/A conversion. · This IC’s output amplifier has an advantage to capacitive load, So, it’s no problem at device action when connect capacitor ( 0.1µF Max ) among output to GND for every noise elimination. Standard Application Circuit Vcc Ao1 + 10µF VrefU Ao2 Analog voltage output + 10µF LD MCU CLK DI Ao11 VrefL + 10µF Ao12 R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 GND Page 7 of 9 R2A20169NP/SA/SP Datasheet Package Dimensions PWQN0020KB-A [NP] PRSP0020DD-B [SP] R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Page 8 of 9 Datasheet R2A20169NP/SA/SP PTSP0020JB-A [SA] Ordering Information Order part No. Package Name Package Code Package type No. Packing/Quantity R2A20169SP#W5 SOP-20 PRSP0020DD-B SP Embossed Taping/2,000 pcs. R2A20169SA#W5 TSSOP-20 RTSP0020JB-A SA Embossed Taping/2,000 pcs. R2A20169NP#W5 QFN-20 PWQN0020KB-A NP Embossed Taping/2,500 pcs. R03DS0020EJ0300 Rev.3.00 Jul 25, 2013 Page 9 of 9 Notice 1. Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits, software, or information. 2. Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics 3. Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein. technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or others. 4. You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or 5. Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product. the product's quality grade, as indicated below. "Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic equipment; and industrial robots etc. "High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc. Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics. 6. You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges. 7. Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or systems manufactured by you. 8. Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations. 9. Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations. 10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics products. 11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics. 12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries. (Note 1) "Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries. (Note 2) "Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics. SALES OFFICES http://www.renesas.com Refer to "http://www.renesas.com/" for the latest and detailed information. Renesas Electronics America Inc. 2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A. Tel: +1-408-588-6000, Fax: +1-408-588-6130 Renesas Electronics Canada Limited 1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada Tel: +1-905-898-5441, Fax: +1-905-898-3220 Renesas Electronics Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K Tel: +44-1628-651-700, Fax: +44-1628-651-804 Renesas Electronics Europe GmbH Arcadiastrasse 10, 40472 Düsseldorf, Germany Tel: +49-211-65030, Fax: +49-211-6503-1327 Renesas Electronics (China) Co., Ltd. 7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China Tel: +86-10-8235-1155, Fax: +86-10-8235-7679 Renesas Electronics (Shanghai) Co., Ltd. Unit 204, 205, AZIA Center, No.1233 Lujiazui Ring Rd., Pudong District, Shanghai 200120, China Tel: +86-21-5877-1818, Fax: +86-21-6887-7858 / -7898 Renesas Electronics Hong Kong Limited Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong Tel: +852-2886-9318, Fax: +852 2886-9022/9044 Renesas Electronics Taiwan Co., Ltd. 13F, No. 363, Fu Shing North Road, Taipei, Taiwan Tel: +886-2-8175-9600, Fax: +886 2-8175-9670 Renesas Electronics Singapore Pte. Ltd. 80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949 Tel: +65-6213-0200, Fax: +65-6213-0300 Renesas Electronics Malaysia Sdn.Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: +60-3-7955-9390, Fax: +60-3-7955-9510 Renesas Electronics Korea Co., Ltd. 11F., Samik Lavied' or Bldg., 720-2 Yeoksam-Dong, Kangnam-Ku, Seoul 135-080, Korea Tel: +82-2-558-3737, Fax: +82-2-558-5141 © 2013 Renesas Electronics Corporation. All rights reserved. Colophon 2.2