TS61089

TS61089
Dual Programmable Transient Voltage Suppressor
General Description
This device has been especially designed to
protect 2 new high voltage, as well as classical
SLICs, against transient overvoltages.
Positive overvoltages are clamped by 2 diodes.
Features
z Dual
line
programmable
voltage
z Wide negative firing voltage range:
VMGL = -75V (S61089)
VMGL = -100V (S61089A)
breakdown voltage being referenced to –VBAT
VMGL = -155V (S61089B)
This component presents a very low gate
transient
suppressor
Negative surges are suppressed by 2 thyristors, their
through the gate.
Revision:B
z Low dynamic switching voltages: VFP and
VDGL
triggering current (IGT) in order to reduce the current
z Low gate triggering current: IGT = 5 mA max
consumption on printed circuit board during the firing
z Peak pulse current: IPP = 30 A (10/1000 s)
phase.
z Holding current: IH > 150 mA
Benefits
This devices are not subject to ageing and
provide a fail safe mode in short circuit for a better
Marking
protection. Trisils are used to help equipment to meet
various standards such as UL1950, IEC950 / CSA
C22.2, UL1459 and FCC part68.
SOP-8
TYPE
MARKING
TS61089
SE69
TS61089A
SE69A
TS61089B
SE69B
TS61089
Absolute Maximum Ratings
Parameter
Repetitive peak off-state votage, VGK=0
Symbol
Repetitive peak gate-cathode voltage, VKA=0
VDRM
-120
TS61089B
-170
TS61089
-85
TS61089A
Units
-90
TS61089
TS61089A
Value
VGKRM
-120
V
V
-170
TS61089B
Non-repetitive peak on-state current
30
10/1000 us (Telcordia(Bellcore)Gr-1089-CORE.Issue 2.February 1999,Section4)
5/320 us (ITU-T K.20, K.21& K.45, K.44 open-circuit voltage wave shape 10/700us)
IPPSM
40
1.2/50 us (Telcordia(Bellcore)Gr-1089-CORE.Issue 2.February 1999,Section4)
100
2/10 us (Telcordia(Bellcore)Gr-1089-CORE.Issue 2.February 1999,Section4)
120
A
Non-repetitive peak on-state current. VGG=-75V 50Hz to 60Hz
0.1 s
11
1s
4.8
5s
ITSM
2.7
300 s
0.95
900 s
0.93
A
Operating free-air temperature range
TA
-40 to +85
°C
Operating Junction Temperature Range
TJ
-40 to +150
°C
TSTG
-40 to +150
°C
RθJA
170
°C/W
Storage Temperature Range
Themal Characteristics
Junction To ambient
Parameter Measurement Information
Figure 1. Voltage-Current Charateristic
Unless Otherwise Noted, All Voltages are Referenced to the Anode
TS61089
Electrical Parameter
Symbol
Parameter
ID
Off-state current
IH
Holding current
V(BO)
Breakover voltage
VF
Forward voltage
VFRM
Peak forward recovery voltage
VGK(BO)
Gate-cathode impluse breakover voltage
IGKS
Gate reverse current
IGT
Gate trigger current
VGT
Gate-cathode trigger voltage
CKA
Cathode-anode off-state capacitance
Electrical Characteristics Ratings at 25°C ambient temperature unless otherwise specified.
Parameter
ID
V(BO)
VGK(BO)
VF
VFRM
IH
Off-state current
Breakover voltage
Gate-cathode impulse
Breakover voltage
Forward voltage
Peak forward recovery
voltage
Test Conditions
VD=VDRM, VGK=0
State capacitance
TJ=85 ℃
-50
uA
1.2/50us,IPP=-96A,RS=52Ω,VGG=-48V,CG=220nF
-64
2/10us,IPP=-56A,RS=45Ω,VGG=-48V,CG=220nF
9
2/10us,IPP=-100A,RS=50Ω,VGG=-48V,CG=220nF
12
1.2/50us,IPP=-53A,RS=47Ω,VGG=-48V,CG=220nF
12
1.2/50us,IPP=-96A,RS=52Ω,VGG=-48V,CG=220nF
16
IF = 5 A, TW = 200 us
V
V
3
2/10us,IPP=-56A,RS=45Ω,VGG=-48V,CG=220nF
6
2/10us,IPP=-100A,RS=50Ω,VGG=-48V,CG=220nF
8
1.2/50us,IPP=-53A,RS=47Ω,VGG=-48V,CG=220nF
8
1.2/50us,IPP=-96A,RS=52Ω,VGG=-48V,CG=220nF
12
Gate trigger current
Cathode-anode off-
uA
-60
IGT
CKA
-5
1.2/50us,IPP=-53A,RS=47Ω,VGG=-48V,CG=220nF
VGG = VGK = VGKRM, VKA = 0
Gate switching charge
TJ=25 ℃
-60
Gate reverse current
QGS
Unit
2/10us,IPP=-100A,RS=50Ω,VGG=-48V,CG=220nF
IGKS
voltage
Max
-57
IT = -1 A, di/dt = 1A/ms, VGG =-48 V
Gate-cathode trigger
Typ
2/10us,IPP=-56A,RS=45Ω,VGG=-48V,CG=220nF
Holding current
VGT
Min
V
V
-150
mA
TJ=25 ℃
-5
uA
TJ=85 ℃
-50
uA
IT = -3 A, tp(g) ≥ 20 us, VGG = -48V
5
mA
IT = -3 A, tp(g) ≥ 20 us, VGG = -48V
2.5
V
1.2/50us,IPP=-53A,RS=47Ω,VGG=-48V, CG=220nF
F=1 MHz, Vd=1V, IG=0
0.1
uC
VD= -3 V
100
pF
VD=-48 V
50
pF
TS61089
Typical Characteristics
Peak Non-Recurring AC
vs.
Current Duration
Fig2. Non-repetitive Peak On-State Current against Duration
TS61089
SOP-8 MECHANICAL DATA
DIM
Millimeters
MIN
TYP
A
MAX
1.75
A1
0.10
A2
1.35
1.55
1.75
B
0.35
0.42
0.49
C
0.19
D
4.80
4.90
5.00
E
5.80
6.00
6.20
E1
3.80
3.95
4.00
e
L
K
0.25
0.25
1.27
0.40
0
o
0.90
8o