Six Channel SiC MOSFET Driver Gate Driver for 1200V SiC MOSFET Power Module Features 6 output channels Isolated power supply Direct mount low inductance design Short circuit protection Over temperature protection Under voltage protection For use with Cree Module 45mm, 6-pak modules. Applications 6-pak Driver for 1.2kV, SiC MOSFET modules DC Bus voltage up to 900VDC Absolute Maximum Ratings Symbol Vs ViH ViL IO.pk IO.avg.ma x FMax Parameter Visol Top Tstg Supply voltage Vi Input signal voltage on/off Supply current (no load) Supply current (switching) Input threshold voltage HIGH Input threshold voltage LOW Turn on propogation delay Turn off propogation delay Pulse width for resetting fault Weight Mean time between failure ViT+ ViTTdon Tdoff Terr W MTBF 1 Parameter VS ISO 16 5 0 9 2 V V V A 150 1200 kHz Ouput average current Characteristics Symbol Unit Power Supply Voltage Input signal voltage HIGH Input signal voltage LOW Output peak current Max. Switching frequency Max. Drain to source voltage Input to output isolation voltage Operating temperature Storage temperature VDS Value CGD15FB45P Rev - Part Number Package Marking CGD15FB45P PCBA CGD15FB45P Rev2 Test Conditions Vs ramp rate >50V/sec A Vg=+20/-5, Rg = 10 V ±1200 V -25 to 70 -40 to 85 ºC ºC Min Value Typ Max 13.0 15.0 16.0 3.5 800 Note 5/0 330 830 420 1000 210 225 1.5 280 295 300 1.5 Unit Test Conditions V V mA V V nS nS nS g 6 10 h 70C 70C, 150khz Notes Driver Overview Block Diagram Note: Default gate resistor for Rg is 10 for gate ON and OFF. The user can control the gate turn ON and OFF speed by changing Rg to a lower value and gain better MOSFET switching efficiency. The user can also control the Gate turn-ON and OFF speed independently by populating Rg.off and D1. Cs is made up of 3x 2.2nF, 1.2kV film capacitors. 2 CGD15FB45P Rev - X1 – 26 pos Signal connector (FCI p/n# 71918-126LF) 1 3 5 7 9 11 13 15 17 19 21 23 25 PWM_Upper_A (5V Logic) PWM_Lower_A (5V Logic) PWM_Upper_B (5V Logic) PWM_Lower_B (5V Logic) PWM_Upper_C (5V Logic) PWM_Lower_C (5V Logic) /RST (normally hi) RDY (normally hi) DESAT FAULT (normally low) OVER_TEMP_FLT (normally low) 2 4 6 8 10 12 14 16 18 20 22 24 26 PWR In (Vs) LED Status Indicators L1 L3 L5 L7 RED led, illuminated when Phase A upper switch has a desat fault. RED led, illuminated when Phase B upper switch has a desat fault. RED led, illuminated when Phase C upper switch has a desat fault. GREEN led, illuminated when power is present and all faults are clear. L2 L4 L6 L8 COMMON RED led, illuminated when Phase A lower switch has a desat fault. RED led, illuminated when Phase B lower switch has a desat fault. RED led, illuminated when Phase C lower switch has a desat fault. RED led, illuminated when there is an over temp fault. Fault Handling Each of the six gate drive channels is protected by a desaturation circuit. In the event of a short circuit, the voltage across the MOSFET (VDS) rises until it hits a threshold which causes the desaturation circuit to drive all six gate drive channels to their off state. Pin 17 of the 26 pin main signal connector toggles high when a desaturation event occurs. There will also be a red LED (L1-L6) illuminated for the gate drive channel(s) that activated the desaturation protection. Once the fault is cleared, the circuit can be reset with the onboard reset button or remotely by pulling pin 13 of the 26 pin ribbon connector to common. There is an overtemperature protection circuit that turns off all the gates in the event an overtemperature is detected. The overtemperature circuit reads the value of the six pack module’s onboard NTC. When the NTC reaches a value corresponding to 115C, the overtemperature circuit is activated and all six gate drive channels are driven to their low state. Pin 19 of the 26 pin ribbon connector is toggled high when an overtemperature fault occurs. 3 CGD15FB45P Rev - Typical Application 4 CGD15FB45P Rev - Mechanical Instructions Designed to directly mount to Cree 45 mm style power modules, the 6-ch gate driver also has several other mounting holes to secure the assembly. Attach the gate driver board to the power module via the 4x Module screw holes (see diagram below) using the recommended hardware in Table 1. Then solder the 28x solder pins via the solder pin holes to electrically connect the driver board to the power module. The solder must not exceed 260ºC and the solder per pin must not exceed 10 seconds. The solder joints should be in accordance with IPC A 610 Rev D (or later) – Class 3 to ensure an optimal connection between the module and gate driver board. The module plus driver board assembly must be further supported by securing the assembly to standoffs via the 9x Mounting holes shown in the figure below. Table 1 Hardware List Ref Module screw holes Mounting holes Access holes Solder pin holes Power terminals Description 2.5mm clearance holes for mounting screws to secure the module to the printed circuit board assembly. 4.3mm clearance holes for screws to secure the circuit assembly to standoffs for additional support. 10mm clearance hole to provide access to the screw that secure the module to the heatsink. 1.6mm plated holes for solder pins from power module. Hardware 5mm holes to secure power cables. Locations Torque M2.5 x 4mm 4x 0.5 Nm 6-32 x 5/6” Zinc Plated pan head screw /w internal tooth washer. 9x 0.9 Nm n/a 2x n/a Solder pins from power module 28x n/a * 7x * Power terminal holes are sized to accept a PENN broaching nut (#P-KFS2-032). A 10-32, 6mm screw with a captured lock washer should be used with this broaching nut. 5 CGD15FB45P Rev - Mechanical Drawing (units in Inches) This product has not been designed or tested for use in, and is not intended for use in, applications implanted into the human body nor in applications in which failure of the product could lead to death, personal injury or property damage, including but not limited to equipment used in the operation of nuclear facilities, life-support machines, cardiac defibrillators or similar emergency medical equipment, aircraft navigation or communication or control systems, air traffic control systems, or weapons systems. Copyright © 2014 Cree, Inc. All rights reserved. The information in this document is subject to change without notice. Cree and the Cree logo are registered trademarks and Z-REC and Z-FET are trademarks of Cree, Inc. 6 CGD15FB45P Rev - Cree, Inc. 4600 Silicon Drive Durham, NC 27703 USA Tel: +1.919.313.5300 Fax: +1.919.313.5451 www.cree.com/power