FED40W FED40W SERIES DC-DC CONVERTER 4:1 WIDE INPUT RANGE UP TO 40Watts FEATURES APPLICATIONS • NO MINIMUM LOAD REQUIRED • LOW STANDBY POWER CONSUMPTION • 1600VDC INPUT TO OUTPUT ISOLATION • SIX-SIDED CONTINUOUS SHIELD • STANDARD 2.00 X 1.00 X 0.40 INCH • SAFETY MEETS UL60950-1, EN60950-1 IEC60950-1 AND EN50155 • CE MARK MEETS 2006/95/EC, 2011/95/EC and 2004/108/EC • COMPLIANT TO RoHS EU DIRECTIVE 2011/65/EU 1600VDC ISOLATION REMOTE CONTROL UVP RAILWAY SYSTEM WIRELESS NETWORK TELECOM/DATACOM INDUSTRY CONTROL SYSTEM DISTRIBUTED POWER ARCHITECTURES SEMICONDUCTOR EQUIPMENT OCP SCP OVP OTP LOW STANDBY POWER TECHNICAL SPECIFICATION All specifications are typical at nominal input, full load and 25℃ otherwise noted Model Number FED40-24S3P3W FED40-24S05W FED40-24S12W FED40-24S15W FED40-24S24W FED40-24D12W FED40-24D15W FED40-24D24W FED40-48S3P3W FED40-48S05W FED40-48S12W FED40-48S15W FED40-48S24W FED40-48D12W FED40-48D15W FED40-48D24W FED40-110S3P3W FED40-110S05W FED40-110S12W FED40-110S15W FED40-110S24W FED40-110D12W FED40-110D15W FED40-110D24W Input Range Output Voltage Output Current @Full Load Input Current @ No Load Efficiency Maximum Capacitor Load VDC 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 9 ~ 36 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 18 ~ 75 43 ~ 160 43 ~ 160 43 ~ 160 43 ~ 160 43 ~ 160 43 ~ 160 43 ~ 160 43 ~ 160 VDC 3.3 5 12 15 24 ±12 ±15 ±24 3.3 5 12 15 24 ±12 ±15 ±24 3.3 5 12 15 24 ±12 ±15 ±24 mA 10000 8000 3333 2666 1666 ±1666 ±1333 ±833 10000 8000 3333 2666 1666 ±1666 ±1333 ±833 10000 8000 3333 2666 1666 ±1666 ±1333 ±833 mA 15 15 15 15 15 15 15 15 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 10 % 90 91 92 92 91 90 90 91 90 91 92 92 91 90 90 91 88 89 90.5 91 90 89 89 91 µF 26600 20000 3900 2600 1300 ± 2600 ± 1600 ±650 26600 20000 3900 2600 1300 ± 2600 ± 1600 ±650 26600 20000 3900 2600 1300 ± 2600 ± 1600 ±650 PART NUMBER STRUCTURE FED40 Series Name 48 Input Voltage (VDC) 24: 9~36 48: 18~75 110: 43~160 S Output Quantity S: Single D: Dual Page 1 of 4 05 Output Voltage (VDC) 3P3: 3.3 05: 5 12: 12 15: 15 24: 24 12: ±12 15: ±15 24: ±24 W Input Range 4:1 www.pduke.com N HS Remote Control options Heat-sink : Positive logic N: Negative logig : No Heat-sink HS Heat-sink HC Heat-sink with Clamp 2013/03/15 FED40W INPUT SPECIFICATIONS Parameter Conditions 24Vin(nom) 48Vin(nom) 110Vin(nom) 24Vin(nom) 48Vin(nom) 110Vin(nom) 24Vin(nom) 48Vin(nom) 110Vin(nom) Power up Remote ON/OFF 24Vin(nom) 48Vin(nom) 110Vin(nom) Operating input voltage range Start-up voltage Shutdown voltage Start up time Constant resistive load Input surge voltage 1 second, max. Input filter Remote ON/OFF OUTPUT SPECIFICATIONS Parameter Voltage accuracy Line regulation Load regulation Conditions Cross regulation Voltage adjustability Asymmetrical load 25%/100% FL Ripple and noise Measured by 20MHz bandwidth With a 0.1µF/50V X7R MLCC Temperature coefficient Transient response recovery time Over voltage protection Single output Isolation resistance Isolation capacitance Switching frequency Design meet safety standard Page 2 of 4 -0.5 Typ. 75 100 150 % of Iout rated; Hiccup mode Conditions Min. Input to Output Input (Output) to Case 500VDC ℃ BELLCORE TR-NWT-000332 Case 1: 50% Stress, Ta= 40 . MIL-HDBK-217F Ta=25 , Full load (G/B, controlled environment) ℃ www.pduke.com VDC VDC VDC ms Max. Unit +1.0 +0.2 +0.5 +1.0 +5.0 +10 +20 % % 100 125 200 +0.02 % % % mVp-p ℃ %/ 250 µs 3.9 6.2 15 VDC 20 30 150 % Continuous, automatics recovery 3.3Vout 5Vout 12Vout 15Vout 24Vout 1 minute Unit 50 VDC 100 170 Pi type Open or 3 ~ 12VDC Short or 0 ~ 1.2VDC Short or 0 ~ 1.2VDC Open or 3 ~ 12VDC 0.5 mA 3 mA -1.0 -0.2 -0.5 -1.0 -5.0 -10 -10 3.3Vout, 5Vout 12Vout, 15Vout 24Vout Case material Base material Potting material Dimensions Weight MTBF 36 75 160 9 18 43 -0.02 GENERAL SPECIFICATIONS Parameter Isolation voltage Single Dual Dual 3.3Vout, 5Vout, 12Vout 15Vout, 24Vout 25% load step change Zener diode clamp Over load protection Short circuit protection Max. 24 48 110 Min. Low Line to High Line at Full Load No Load to Full Load Typ. 9 18 43 8 16 40 60 60 Positive logic DC-DC ON (Standard) DC-DC OFF Negative logic DC-DC ON (Option) DC-DC OFF Input current of CTRL pin Remote off input current Referenced to –INPUT pin Min. 1600 1600 1 Typ. Max. Unit VDC GΩ 1500 pF 225 250 275 kHz IEC60950-1, UL60950-1, EN60950-1 EN50155 Copper FR4 PCB Silicon (UL94-V0) 2.00 X 1.00 X 0.40 Inch (50.8×25.4×10.2 mm) 32g (1.13oz) 2.661 x 106 hrs 9.865 x 104 hrs 2013/03/15 FED40W ENVIRONMENTAL SPECIFICATIONS Parameter Operating ambient temperature Maximum case temperature Over temperature protection Storage temperature range Thermal impedance (1) Conditions Min. Max. +85 +105 +115 -55 Natural convection (20LFM) Without Heat-sink With Heat-sink Thermal shock Vibration Relative humidity EMC SPECIFICATIONS Parameter EMI (2) Typ. -40 Conditions EN61000-4-2 Radiated immunity Fast transient (3) Surge (3) Conducted immunity EN61000-4-3 EN61000-4-4 EN61000-4-5 EN61000-4-6 ℃ ℃ ℃ ℃ ℃/W +125 10.8 10.3 EN61373, MIL-STD-810F EN61373, MIL-STD-810F 5% to 95% RH Level EN55011,EN55022 ESD Unit Class A Air ± 8kV Contact ± 6kV 20 V/m ± 2kV ± 2kV 10 Vr.m.s Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Perf. Criteria A Note: 1. 2. 3. The heat-sink is optional and P/N: 7G-0020C-F. The FED40 series standard module meets EN55022 Class A and Class B with external components. For more detail information, please contact with P-DUKE. An external filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The FED40-24W recommended an aluminum electrolytic capacitor (Nippon chemi-con KY series, 220µF/100V) and a TVS (SMDJ58A, 58V, 3000Watt peak pulse power) to connect in parallel. The FED40-48W recommended an aluminum electrolytic capacitor (Nippon chemi-con KY series, 220µF/100V) and a TVS (SMDJ120A,120V, 3000Watt peak pulse power) to connect in parallel. The FED40-110W recommended an aluminum electrolytic capacitor (Ruby-con BXF series, 68µF/200V 3pcs in parallel) and a TVS (SMDJ90A, 90V, 3000Watt peak pulse power 2pcs in series connection ) to connect in parallel CAUTION: This power module is not internally fused. An input line fuse must always be used. CHARACTERISTIC CURVE FED40-48S05W Derating Curve FED40-48S05W Derating Curve with Heat-sink FED40-48S05W Efficiency VS Input Voltage Page 3 of 4 FED40-48S05W Efficiency VS Output Load www.pduke.com 2013/03/15 FED40W MECHANICAL DRAWING PIN CONNECTION PIN SINGLE DUAL 1 2 3 4 5 6 + INPUT - INPUT CTRL + OUTPUT - OUTPUT TRIM + INPUT - INPUT CTRL + OUTPUT COMMON - OUTPUT EXTERNAL OUTPUT TRIMMING Output can be externally trimmed by using the method shown below. 1. All dimensions in inch (mm) 2. Tolerance :x.xx±0.02 (x.x±0.5) x.xxx±0.01 (x.xx±0.25) 3. Pin pitch tolerance ±0.01 (0.25) 4. Pin dimension tolerance ±0.004(0.1) Page 4 of 4 www.pduke.com 2013/03/15