RR5-S02-D02 - RSG Electronic Components GmbH

RR5-S02/D02
2.0 Watt 4:1 regulated
single & dual output
DIP24, wide 4:1 input range
Full SMD technology
■ 1500 VDC isolation up to 3500 VDC isolation
■ Continuous short circuit protection
■ Efficiency up to 77%
■ -40°C~85°C operation temperature range
■ Optional metal case
■
■
RR-series, DIL 24 package, metal version, pic. similar
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation
Load regulation
Ripple & Noise (20 MHz bandwith) (1)
Short circuit protection
Temperature coefficient
Capacitor load (2)
ABSOLUTE MAXIMUM RATINGS (4)
± 1%
± 0.5%
± 0.5%
60 mV pk-pk
Continuous
± 0.02%/°C
See table
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
See table
See table
See table
PI Type
35 mA pk-pk
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
24 modes
-0.7 ~ 40 VDC
48 modes
-0.7 ~ 80 VDC
Lead soldering temperature
260°C
(1.5 mm from case 10 sec.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table
I/O isolation voltage (3 sec.) Input/Output 1500~3500 VDC
Metal case / input & output
1000 VDC
I/O isolation capacitance
60 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
100~400 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 2.199 Mhrs.
Safety standard (designed to meet)
IEC 60950-1:2001
1) Typical value at nominal input voltage and full load.
2) Tested by nominal Vin and constant resistor load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
6) It´s necessary to add minimum capacitor in output for
some single models. Please ask for detail value.
PHYSICAL SPECIFICATIONS
Case material
Base material
Pin material
Potting material
Weight
Dimensions
Non-conductive black plastic
(UL94V-0 rated)
Nickel-coated copper
Non-conductive black plastic
(UL94V-0 rated)
Ø 0.5 mm brass solder-coated
Epoxy (UL94V-0 rated)
Metal 15 g, Plastic 12.5 g
1.25“ x 0.8“ x 0.4“
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
ENVIRONMENT SPECIFICATIONS
Operating temperature (See derating curve) -40°C~ 85°C
Maximum case temperature
100°C
Storage temperature
-40°C~125°C
Cooling
Nature convection
Page: 1/4
Last update: 18.02.09
RR5-S02/D02
2.0 Watt 4:1 regulated
single & dual output
NUMBER STRUCTURE
RR5 - XX
XX
S
Output
05=5V
09=9V
Input
12=12V
24=9~36V 15=15V
48=18~72V 24=24V
DERATING CURVE
02
A
1 (M-J/P/K)*
Power Code
02=2W internal
Name/Package
RR5=DIL24
Type
S=Single
D=Dual
Isolation
1=1.5 kVDC
3=3.5 kVDC
* Standard version in plastic case. Add suffix „M“ for metal case!
Please see Pinout-versions page 3 and add suffix „J“, „P“ or „K“!
MODEL SELECTION GUIDE
Model Number
RR5-2405S02AX
RR5-2409S02AX
RR5-2412S02AX
RR5-2415S02AX
RR5-2424S02AX
RR5-2405D02AX
RR5-2409D02AX
RR5-2412D02AX
RR5-2415D02AX
RR5-2424D02AX
RR5-4805S02AX
RR5-4809S02AX
RR5-4812S02AX
RR5-4815S02AX
RR5-4824S02AX
RR5-4805D02AX
RR5-4809D02AX
RR5-4812D02AX
RR5-4815D02AX
RR5-4824D02AX
Input
Range
VDC
9-36
9-36
9-36
9-36
9-36
9-36
9-36
9-36
9-36
9-36
18-72
18-72
18-72
18-72
18-72
18-72
18-72
18-72
18-72
18-72
Input current
No Load /
Full Load (mA)
20 / 119
20 / 115
20 / 112
20 / 112
20 / 114
20 / 122
20 / 119
20 / 115
20 / 115
30 / 117
10 / 57
10 / 55
10 / 54
10 / 54
10 / 55
10 / 58
10 / 57
10 / 55
10 / 55
10 / 57
Output
VDC
5
9
12
15
24
±5
±9
±12
±15
±24
5
9
12
15
24
±5
±9
±12
±15
±24
Output current
Min. Load /
Full Load (mA)
133.3 / 400
74 / 222
55.7 / 167
44.3 / 133
27.7 / 83
±66.7 / ±200
±37 / ±111
±27.7 / ±83
±22.3 / ±67
±14 / ±42
133.3 / 400
74 / 222
55.7 / 167
44.3 / 133
27.7 / 83
±66.7 / ±200
±37 / ±111
±27.7 / ±83
±22.3 / ±67
±14 / ±42
Efficiency
@FL (%)
Capacitor
Load (HF)
70
72
74
74
73
68
70
72
72
71
73
75
77
77
75
71
73
75
75
73
2200
470
470
470
220
±1000
±220
±220
±220
±100
2200
470
470
470
220
±1000
±220
±220
±220
±100
Page: 2/4
Last update: 18.02.09
RR5-S02/D02
2.0 Watt 4:1 regulated
single & dual output
MECHANICAL SPECIFICATIONS (P-Models)
RSG
MECHANICAL SPECIFICATIONS (P-Models)
RSG
■
RR5-XXXXX02AX(P)
■
RR5-XXXXX02AX(MP)
DIL 24 package
Plastic case
„M“ - Metal case
DIL 24 package
Notes:
All dimensions are typical in mm (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
PIN CONNECTIONS (P-Models)
Pin Number
1
2
3
9
10
11
12
13
14
15
16
22
23
24
PIN CONNECTIONS (P-Models High Isolation)
Dual
+V Input
-V Output
Common
N.P.
Common
+V Output
-V Input
-V Input
+V Output
Common
N.P.
Common
-V Output
+V Input
Single
+V Input
N.C.
N.C.
N.P.
-V Output
+V Output
-V Input
-V Input
+V Output
-V Output
N.P.
N.C.
N.C.
+V Input
MECHANICAL SPECIFICATIONS (K-Models)
RSG
■
Pin Number
1
2
3
9
10
11
12
13
14
15
16
22
23
24
Dual
N.P.
-V Input
-V Input
Common
N.P.
-V Output
N.P.
N.P.
+V Output
N.P.
Common
+V Input
+V Input
N.P.
MECHANICAL SPECIFICATIONS (K-Models)
RSG
RR5-XXXXX02AX(K)
Single
N.P.
-V Input
-V Input
N.C.
N.P.
N.C.
N.P.
N.P.
+V Output
N.P.
-V Output
+V Input
+V Input
N.P.
■
RR5-XXXXX02AX(MK)
DIL 24 package
Plastic case
PIN CONNECTIONS (K-Models)
Pin Number
2
3
9
11
14
16
22
23
Single
-V Input
-V Input
N.P.
N.C.
+V Output
-V Output
+V Input
+V Input
Dual
-V Input
-V Input
Common
-V Output
+V Output
Common
+V Input
+V Input
„M“ - Metal case
DIL 24 package
Notes:
All dimensions are typical in mm (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
The Pin connections for High
Isolation „K“-Models are the same
as for normal ones!
Page: 3/4
Last update: 18.02.09
RR5-S02/D02
2.0 Watt 4:1 regulated
single & dual output
MECHANICAL SPECIFICATIONS (J-Models)
RSG
MECHANICAL SPECIFICATIONS (J-Models)
RSG
■
RR5-XXXXX02AX(J)
■
RR5-XXXXX02AX(MJ)
DIL 24 package
Plastic case
PIN CONNECTIONS (J-Models)
Pin Number
1
2
10
11
12
13
15
23
24
Single
+V Input
+V Input
N.C.
N.C.
-V Output
+V Output
N.C.
-V Input
-V Input
Dual
+V Input
+V Input
Common
Common
N.C.
-V Output
+V Output
-V Input
-V Input
„M“- Metal case
DIL 24 package
Notes:
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
The Pin connections for High Isolation „J“-Models are
the same as for normal ones!
Page: 4/4
Last update: 18.02.09
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de