RS2/RD2-S10/D10 1.0 Watt unregulated single & dual output 7 Pin SIP7 / 14 Pin DIP14 package 1000 VDC isolation up to 6000 VDC isolation ■ Low ripple and noise ■ Efficiency up to 80% ■ -40°C~85°C operation temperature range ■ Non-conductive black plastic case ■ EN55022 class B for SIP series ■ ■ OUTPUT SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS (4) Voltage accuracy Line regulation (Per 1% Vin Charge) Load regulation (From 20% to 100% Load) ± 3% ± 1.2% ± 10% ± 20% 75 mV pk-pk ± 0.02%/°C See table (Output 3.3 V Model) Ripple & Noise (20 MHz bandwith) (1) Temperature coefficient Capacitor load (2) These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. Input voltage (100 mS) 5 modes 0 ~ 7 VDC 12 modes 0 ~ 15 VDC 24 modes 0 ~ 28 VDC 48 modes (SIP) 0 ~ 54 VDC Lead soldering temperature 260°C INPUT SPECIFICATIONS (1.5 mm from case 10 sec.) Voltage range Max. input current No-load input current Input filter Input reflected ripple current (3) ± 10% See table See table Capacitors 20 mA pk-pk All specifications typical at Ta = 25°C, nominal input voltage and full load unless otherwise specified. The information and specifications contained in this data sheet are believed to be correct at time of publication. However, we accept no responsibility for consequences arising from printing errors or inaccuracies. Subject to change without notice. GENERAL SPECIFICATIONS NOTE Efficiency See table I/O isolation voltage (3 sec.) Input / output 1000 ~ 6000 VDC I/O isolation capacitance 60 pF typ. I/O isolation resistance 1000 M Ohm Switching frequency variable 80 kHz Humidity 95% rel. H Reliability calculated MTBF (MIL-HDBK-217F) > 1.121 Mhrs. Safety standard (designed to meet) IEC 60950-1 1) Ripple / Noise measured with 20 MHz bandwith. 2) Tested by minimal Vin and constant resistive load. 3) Measured input reflected ripple current with a simulated source inductance of 12uH. 4) Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5) Operation under no-load conditions will not damage these devices. However they may not meet all listed specifications. 6) To reduce converter´s Ripple & Noise it is recommended to add a 4.7HF ~ 100HF capacitor in output end. For EMI performance improvement it is recommended to add a 12HH inductor and a 10HF ~ 100HF capacitor in input end. EMC SPECIFICATIONS Radiated emmisions ESD RS EN55022 FCC 47 CFR Part 15 Subpart B IEC 61000-4-2 IEC 61000-4-3 Class B Class B Perf. criteria B Perf. criteria A PHYSICAL SPECIFICATIONS Case material Non-conductive black plastic (UL94V-0 rated) Pin material 0.5 mm Alloy42 solder-coated Potting material Epoxy (UL94V-0 rated) Weight SIP > 2.3 g, DIP > 2.6 g Dimensions SIP > 0.76“ x 0.24“ x 0.39“ DIP > 0.80“ x 0.40“ x 0.27“ The models listed are just for standard type. If you need a special specification product, please contact our service. Phone: +49 69 984047-0, mail to: [email protected] or use the forms on www.rsg-electronic.de („Kontakt“). ENVIRONMENT SPECIFICATIONS Operating temperature Maximum case temperature Storage temperature Cooling -40°C~ 85°C (See derating curve) 100°C -40°C~125°C Nature convection Page: 1/5 Last update: 23.01.09 RS2/RD2-S10/D10 1.0 Watt unregulated single & dual output NUMBER STRUCTURE RS2 - XX Name/Package RS2=SIL7 RD2=DIL14 Input 05=5V 12=12V 24=24V 48=48V XX Output 03=3.3V 05=5V 07=7.2V 09=9V 12=12V 15=15V 18=18V 24=24V DERATING CURVE S 10 Power 10=1.0W A X Code internal Type S=Single D=Dual Isolation 1=1.0 kVDC 2=2.0 kVDC 3=3.0 kVDC 4=4.0 kVDC 5=5.2 kVDC 6=6.0 kVDC MODEL SELECTION GUIDE Model Number Input Range VDC Input current (mA) No Load / Full Load Output VDC Output current Full Load (mA) Efficiency @FL (%) Capacitor Load (HF) RS2-0503D10AX RS2-0505D10AX RS2-0507D10AX RS2-0509D10AX RS2-0512D10AX RS2-0515D10AX RS2-0518D10AX RS2-0524D10AX RS2-1203D10AX RS2-1205D10AX RS2-1207D10AX RS2-1209D10AX RS2-1212D10AX RS2-1215D10AX RS2-1218D10AX RS2-1224D10AX RS2-2403D10AX RS2-2405D10AX RS2-2407D10AX RS2-2409D10AX RS2-2412D10AX RS2-2415D10AX RS2-2418D10AX RS2-2424D10AX RS2-4803D10AX RS2-4805D10AX RS2-4807D10AX RS2-4809D10AX RS2-4812D10AX RS2-4815D10AX RS2-4818D10AX RS2-4824D10AX 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 24 24 24 24 24 24 24 24 48 48 48 48 48 48 48 48 30 / 307 30 / 270 30 / 259 30 / 256 30 / 256 30 / 250 30 / 253 30 / 250 20 / 126 20 / 111 20 / 109 20 / 109 20 / 106 20 / 104 20 / 104 20 / 109 10 / 61 10 / 56 10 / 54 10 / 54 10 / 53 10 / 53 10 / 53 10 / 53 6 / 34 6 / 30 6 / 30 6 / 29 6 / 28 6 / 28 6 / 29 6 / 30 ±3.3 ±5 ±7.2 ±9 ±12 ±15 ±18 ±24 ±3.3 ±5 ±7.2 ±9 ±12 ±15 ±18 ±24 ±3.3 ±5 ±7.2 ±9 ±12 ±15 ±18 ±24 ±3.3 ±5 ±7.2 ±9 ±12 ±15 ±18 ±24 ±151.5 ±100 ±69.44 ±55.55 ±41.67 ±33.33 ±27.77 ±20.83 ±151.5 ±100 ±69.44 ±55.55 ±41.67 ±33.33 ±27.77 ±20.83 ±151.5 ±100 ±69.44 ±55.55 ±41.67 ±33.33 ±27.77 ±20.83 ±151.5 ±100 ±69.44 ±55.55 ±41.67 ±33.33 ±27.77 ±20.83 65 74 77 78 78 80 79 80 66 75 76 76 78 80 80 76 68 74 76 76 78 78 78 78 60 70 70 72 74 74 72 70 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 Page: 2/5 Last update: 23.01.09 RS2/RD2-S10/D10 1.0 Watt unregulated single & dual output Model Number Input Range VDC Input current (mA) No Load / Full Load Output VDC Output current Full Load (mA) Efficiency @FL (%) Capacitor Load (HF) RD2-0503D10AX RD2-0505D10AX RD2-0507D10AX RD2-0509D10AX RD2-0512D10AX RD2-0515D10AX RD2-0518D10AX RD2-0524D10AX RD2-1203D10AX RD2-1205D10AX RD2-1207D10AX RD2-1209D10AX RD2-1212D10AX RD2-1215D10AX RD2-1218D10AX RD2-1224D10AX RD2-2403D10AX RD2-2405D10AX RD2-2407D10AX RD2-2409D10AX RD2-2412D10AX RD2-2415D10AX RD2-2418D10AX RD2-2424D10AX RS2-0503S10AX RS2-0505S10AX RS2-0507S10AX RS2-0509S10AX RS2-0512S10AX RS2-0515S10AX RS2-0518S10AX RS2-0524S10AX RS2-1203S10AX RS2-1205S10AX RS2-1207S10AX RS2-1209S10AX RS2-1212S10AX RS2-1215S10AX RS2-1218S10AX RS2-1224S10AX RS2-2403S10AX RS2-2405S10AX RS2-2407S10AX RS2-2409S10AX RS2-2412S10AX RS2-2415S10AX RS2-2418S10AX RS2-2424S10AX 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 24 24 24 24 24 24 24 24 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 24 24 24 24 24 24 24 24 30 / 307 30 / 270 30 / 159 30 / 156 30 / 156 30 / 150 30 / 156 30 / 166 20 / 126 20 / 111 20 / 115 20 / 111 20 / 106 20 / 106 20 / 111 20 / 111 10 / 62 10 / 57 10 / 59 10 / 55 10 / 53 10 / 55 10 / 57 10 / 59 30 / 267 30 / 256 30 / 270 30 / 267 30 / 263 30 / 263 30 / 267 30 / 278 20 / 113 20 / 113 20 / 113 20 / 111 20 / 108 20 / 106 20 / 106 20 / 113 10 / 56 10 / 54 10 / 56 10 / 56 10 / 53 10 / 53 10 / 53 10 / 53 ±3.3 ±5 ±7.2 ±9 ±12 ±15 ±18 ±24 ±3.3 ±5 ±7.2 ±9 ±12 ±15 ±18 ±24 ±3.3 ±5 ±7.2 ±9 ±12 ±15 ±18 ±24 3.3 5 7.2 9 12 15 18 24 3.3 5 7.2 9 12 15 18 24 3.3 5 7.2 9 12 15 18 24 ±151.5 ±100 ±69.44 ±55.55 ±41.67 ±33.33 ±27.77 ±20.83 ±151.5 ±100 ±69.44 ±55.55 ±41.67 ±33.33 ±27.77 ±20.83 ±151.5 ±100 ±69.44 ±55.55 ±41.67 ±33.33 ±27.77 ±20.83 303 200 138.9 111.1 83.3 66.7 55.6 41.7 303 200 138.9 111.1 83.3 66.7 55.6 41.7 303 200 138.9 111.1 83.3 66.7 55.6 41.7 65 74 77 78 78 80 78 75 66 75 72 75 78 78 75 75 67 72 70 75 78 75 72 70 75 78 74 75 76 76 75 72 74 74 74 75 77 78 78 75 75 77 75 75 78 78 78 78 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 ±100 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 Page: 3/5 Last update: 23.01.09 RS2/RD2-S10/D10 1.0 Watt unregulated single & dual output Model Number Input Range VDC Input current (mA) No Load / Full Load Output VDC Output current Full Load (mA) Efficiency @FL (%) Capacitor Load (HF) RS2-4803S10AX RS2-4805S10AX RS2-4807S10AX RS2-4809S10AX RS2-4812S10AX RS2-4815S10AX RS2-4818S10AX RS2-4824S10AX RD2-0503S10AX RD2-0505S10AX RD2-0507S10AX RD2-0509S10AX RD2-0512S10AX RD2-0515S10AX RD2-0518S10AX RD2-0524S10AX RD2-1203S10AX RD2-1205S10AX RD2-1207S10AX RD2-1209S10AX RD2-1212S10AX RD2-1215S10AX RD2-1218S10AX RD2-1224S10AX RD2-2403S10AX RD2-2405S10AX RD2-2407S10AX RD2-2409S10AX RD2-2412S10AX RD2-2415S10AX RD2-2418S10AX RD2-2424S10AX 48 48 48 48 48 48 48 48 5 5 5 5 5 5 5 5 12 12 12 12 12 12 12 12 24 24 24 24 24 24 24 24 6 / 29 6 / 29 6 / 29 6 / 28 6 / 28 6 / 28 6 / 29 6 / 30 30 / 267 30 / 256 30 / 267 30 / 267 30 / 263 30 / 263 30 / 267 30 / 278 20 / 113 20 / 113 20 / 113 20 / 111 20 / 108 20 / 106 20 / 106 20 / 111 10 / 56 10 / 54 10 / 56 10 / 56 10 / 53 10 / 53 10 / 53 10 / 53 3.3 5 7.2 9 12 15 18 24 3.3 5 7.2 9 12 15 18 24 3.3 5 7.2 9 12 15 18 24 3.3 5 7.2 9 12 15 18 24 303 200 138.9 111.1 83.3 66.7 55.6 41.7 303 200 138.9 111.1 83.3 66.7 55.6 41.7 303 200 138.9 111.1 83.3 66.7 55.6 41.7 303 200 138.9 111.1 83.3 66.7 55.6 41.7 72 72 72 74 74 75 72 70 75 78 75 75 76 76 75 72 74 74 74 75 77 78 78 75 75 77 75 75 78 78 78 78 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 LOADING VS OUTPUT VOLTAGE LOADING VS OUTPUT VOLTAGE 12 MODELS Output Voltage Output Voltage 5 MODELS Load Load Page: 4/5 Last update: 23.01.09 RS2/RD2-S10/D10 1.0 Watt unregulated single & dual output LOADING VS OUTPUT VOLTAGE LOADING VS OUTPUT VOLTAGE 48 MODELS Output Voltage Output Voltage 24 MODELS Load MECHANICAL SPECIFICATIONS 7 Pin SIL Load PIN CONNECTIONS 7 Pin SIL Pin No. 1 2 4 5 6 7 MECHANICAL SPECIFICATIONS 14 Pin DIL Single -A1 +V Input +V Input -V Input -V Input -V Output -V Output N.P. Common +V Output +V Output N.P. N.P. Single -A2/A3/ A4/A5/A6 Dual -A2/A3/ A4/A5/A6 +V Input -V Input N.P. -V Output N.P. +V Output +V Input -V Input N.P. -V Output Common +V Output PIN CONNECTIONS 14 Pin DIL Pin No. 1 7 8 9 10 11 14 Single -A1 Dual -A1 -V Input -V Input N.C. N.C. N.P. Common +V Output +V Output N.P. N.P. -V Output -V Output +V Input +V Input Notes: All dimensions are typical in millimeters (inches). 1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002) 2) Pin pitch tolerance: ± 0.35 (± 0.014) 3) Case tolerance: ± 0.5 (± 0.02) RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach Dual -A1 Single -A2/A3/ A4/A5/A6 Dual -A2/A3/ A4/A5/A6 -V Input N.C. +V Output N.P. -V Output N.P. +V Input -V Input N.C. +V Output Common -V Output N.P. +V Input Page: 5/5 Last update: 23.01.09 Tel. +49 69 984047-0 Fax +49 69 984047-77 mail: [email protected] www.rsg-electronic.de