RR4-S02 & RR4-D02 series, RSG 2W regulated single & dual

RR4-S02/D02
2 Watt 2:1 regulated
single & dual output
DIP24, wide 2:1 input range
Full SMD technology
■ 1500 VDC isolation, up to 3500 VDC
■ Continuous short circuit protection
■ Efficiency up to 78%
■ -40°C~85°C operation temperature range
■ Optional plastic case
■
■
OUTPUT SPECIFICATIONS
ENVIRONMENT SPECIFICATIONS
Voltage accuracy
Line regulation
Load regulation
Operating temperature (See derating curve)
-40°C~ 85°C
Maximum case temperature
100°C
Storage temperature
-40°C~125°C
Cooling
Nature convection
± 1%
± 0.5%
± 0.5%
(Output 3.3 V / ±3.3 V Model)
± 1.5%
Ripple & Noise (20 MHz bandwith) (1)
60 mV pk-pk
Short circuit protection
Indefinite (automatic recovery)
Temperature coefficient
± 0.02%/°C
Capacitor load (2)
See table
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
See table
See table
See table
PI Type
35 mA pk-pk
GENERAL SPECIFICATIONS
Efficiency
See table, typ.
I/O isolation voltage (3 sec.)
Input / Output
1500 VDC ~ 3500 VDC
Metal case / Input & Output
1000 VDC
I/O isolation capacitance
470 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
typ. 266 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F) > 1.121 Mhrs.
Safety standard (designed to meet)
IEC 60950-1:2001
PHYSICAL SPECIFICATIONS
Case material
Nickel-coated copper
Non-conductive black plastic (UL94V-0 rated)
Base material Non-conductive black plastic (UL94V-0 rated)
Pin material
Ø 0.5 mm brass solder-coated
Potting material
Epoxy (UL94V-0 rated)
Weight
17.0 g Metal, 13.5 g Plastic
Dimensions
1.25“ x 0.8“ x 0.4“
ABSOLUTE MAXIMUM RATINGS (4)
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
12 modes
-0.7 ~ 24 VDC
24 modes
-0.7 ~ 40 VDC
48 modes
-0.7 ~ 80 VDC
Lead soldering temperature
260°C
(1.5 mm from case 10 sec.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
NOTE
1) Typical value at nominal input voltage and full load.
2) Tested by nominal Vin and constant resistor load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
Page: 1/3
Last update: 03.10.07
RR4-S02/D02
2 Watt 2:1 regulated
single & dual output
NUMBER STRUCTURE
RR4
-
XX
Name/Package
RR4=DIL24
Input
12=9~18V
24=18~36V
48=36~72V
XX
Output
03=3.3V
05=5V
12=12V
15=15V
DERATING CURVE
S/D 02
Power
02=2W
A
1 (P)*
Code
internal
Type
S=Single
D=Dual
Isolation
1=1.5 kVDC
3=3.5 kVDC
* Add suffix P at the end for Plastic Case!
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RR4-1203S02AX
RR4-1205S02AX
RR4-1209S02AX
RR4-1212S02AX
RR4-1215S02AX
RR4-1224S02AX
RR4-1203D02AX
RR4-1205D02AX
RR4-1209D02AX
RR4-1212D02AX
RR4-1215D02AX
RR4-1224D02AX
RR4-2403S02AX
RR4-2405S02AX
RR4-2409S02AX
RR4-2412S02AX
RR4-2415S02AX
RR4-2424S02AX
RR4-2403D02AX
RR4-2405D02AX
RR4-2409D02AX
RR4-2412D02AX
RR4-2415D02AX
RR4-2424D02AX
RR4-4803S02AX
RR4-4805S02AX
RR4-4809S02AX
RR4-4812S02AX
RR4-4815S02AX
RR4-4824S02AX
RR4-4803D02AX
RR4-4805D02AX
RR4-4809D02AX
RR4-4812D02AX
RR4-4815D02AX
RR4-4824D02AX
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
36-72
30 / 223
30 / 222
30 / 219
30 / 219
30 / 219
30 / 219
30 / 229
30 / 219
30 / 219
30 / 219
30 / 219
30 / 219
20 / 109
20 / 107
20 / 107
20 / 107
20 / 107
20 / 107
20 / 112
20 / 109
20 / 107
20 / 107
20 / 107
20 / 107
12 / 56
12 / 56
12 / 56
12 / 56
12 / 56
12 / 56
12 / 56
12 / 56
12 / 56
12 / 56
12 / 56
12 / 56
3.3
5
9
12
15
24
±3.3
±5
±9
±12
±15
±24
3.3
5
9
12
15
24
±3.3
±5
±9
±12
±15
±24
3.3
5
9
12
15
24
±3.3
±5
±9
±12
±15
±24
600
400
222
167
133
83
±300
±200
±111
±83
±67
±42
600
400
222
167
133
83
±300
±200
±111
±83
±67
±42
600
400
222
167
133
83
±300
±200
±111
±83
±67
±42
74
75
76
76
76
76
72
75
76
76
76
76
76
78
78
78
78
78
74
76
78
78
78
78
74
75
75
75
75
75
74
75
75
75
75
75
680
680
330
220
100
33
±330
±330
±100
±47
±33
±22
680
680
330
220
100
33
±330
±330
±100
±47
±33
±22
680
680
330
220
100
33
±330
±330
±100
±47
±33
±22
Page: 2/3
Last update: 03.10.07
RR4-S02/D02
2 Watt 2:1 regulated
single & dual output
EFFICIENCY VS OUTPUT CURRENT 12
EFFICIENCY VS OUTPUT CURRENT 24
12 MODELS
EFFICIENCY VS OUTPUT CURRENT 48
48 MODELS
24 MODELS
PIN CONNECTIONS
Pin Number
Single
Dual
2
3
9
11
14
16
22
23
-V Input
-V Input
N.P.
N.C.
+V Output
-V Output
+V Input
+V Input
-V Input
-V Input
Common
-V Output
+V Output
Common
+V Input
+V Input
The pin connection of high isolation
models is the same as for normal ones.
MECHANICAL SPECIFICATIONS METAL CASE
MECHANICAL SPECIFICATIONS PLASTIC CASE
24 Pin DIL package
Nickel coated copper
24 Pin DIL package
Plastic case (optional)
RSG
RSG
RR4-XXXXX02A1
RR4-XXXXX02A1P
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
Page: 3/3
Last update: 03.10.07
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de