RS6-R20 - RSG Electronic Components GmbH

RS6-R20
2.0 Watt regulated
single output
12 Pin SIP12 package
1000 VDC isolation up to 3000 VDC isolation
■ Continuous short circuit protection
■ Efficiency up to 69%
■ -25°C~71°C operation temperature range
■
■
SIL 12 package, pic. similar
OUTPUT SPECIFICATIONS
ABSOLUTE MAXIMUM RATINGS (4)
Voltage accuracy
Line regulation
Load regulation (From 0% to 100% Load)
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
5 modes
0 ~ 7 VDC
12 modes
0 ~ 15 VDC
24 modes
0 ~ 28 VDC
Lead soldering temperature
260°C
± 2%
± 0.5%
± 0.5%
(3.3 V output model)
± 1.5%
Ripple & Noise (20 MHz bandwith) (1)
75 mV pk-pk
Short circuit protection
Indefinite (automatic recovery)
Temperature coefficient
± 0.02%/°C
Capacitor load (2)
See table
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
± 10%
See table
See table
Capacitors
20 mA pk-pk
(1.5 mm from case 10 sec.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table
I/O isolation voltage (3 sec.)
Input / output
1000 ~ 3000 VDC
I/O isolation capacitance
60 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
50 kHz typ.
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 1.12 Mhrs.
Safety standard (designed to meet)
IEC 60950-1
1) Ripple / Noise measured with 20 MHz bandwith.
2) Tested by minimal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
PHYSICAL SPECIFICATIONS
Case material
Pin material
Potting material
Weight
Dimensions
Non-conductive black plastic
(UL94V-0 rated)
0.5 mm Alloy42 solder-coated
Epoxy (UL94V-0 rated)
7.2 g
1.26“ x 0.32“ x 0.57“
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
ENVIRONMENT SPECIFICATIONS
Operating temperature
Maximum case temperature
Storage temperature
Cooling
-25°C~ 71°C
(See derating curve)
100°C
-40°C~125°C
Nature convection
Page: 1/3
Last update: 18.02.09
RS6-R20
2.0 Watt regulated
single output
NUMBER STRUCTURE
RS6 -
XX
Name/Package
RS6=SIL12
Input
05=5V
12=12V
24=24V
XX
Output
03=3.3V
05=5V
07=7.2V
09=9V
12=12V
15=15V
18=18V
24=24V
DERATING CURVE
R
20
Power
20=2.0W
A
X
Code
internal
Type
R=Single
regulated
Isolation
1=1.0 kVDC
3=3.0 kVDC
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RS6-0503R20AX
RS6-0505R20AX
RS6-0507R20AX
RS6-0509R20AX
RS6-0512R20AX
RS6-0515R20AX
RS6-0518R20AX
RS6-0524R20AX
RS6-1203R20AX
RS6-1205R20AX
RS6-1207R20AX
RS6-1209R20AX
RS6-1212R20AX
RS6-1215R20AX
RS6-1218R20AX
RS6-1224R20AX
RS6-2403R20AX
RS6-2405R20AX
RS6-2407R20AX
RS6-2409R20AX
RS6-2412R20AX
RS6-2415R20AX
RS6-2418R20AX
RS6-2424R20AX
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
70 / 515
70 / 606
70 / 606
70 / 597
80 / 597
80 / 597
80 / 597
80 / 579
30 / 214
30 / 252
30 / 252
45 / 248
45 / 248
45 / 248
50 / 245
50 / 245
25 / 107
25 / 124
25 / 124
25 / 122
25 / 122
25 / 122
25 / 120
25 / 120
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
500
400
277.7
222.2
166.6
133.3
111.1
83.3
500
400
277.7
222.2
166.6
133.3
111.1
83.37
500
400
277.7
222.2
166.6
133.3
111.1
83.3
64
66
66
67
67
67
67
69
64
66
66
67
67
67
68
68
64
67
67
68
68
68
69
69
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
330
Page: 2/3
Last update: 18.02.09
RS6-R20
2.0 Watt regulated
single output
LOADING VS OUTPUT VOLTAGE 05
MECHANICAL SPECIFICATIONS 12 Pin SIL
05 MODELS
LOADING VS OUTPUT VOLTAGE 12
12 MODELS
Notes:
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
LOADING VS OUTPUT VOLTAGE 24
24 MODELS
PIN CONNECTIONS
PIN NUMBER
Single
Single -A3
1
2
3
9
10
11
12
+V Input
N.C.
N.C.
N.C.
-V Output
+V Output
-V Input
+V Input
-V Input
N.C.
N.C.
-V Output
+V Output
N.C.
Page: 3/3
Last update: 18.02.09
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de