RS1-S02 - RSG Electronic Components GmbH

RS1/RD1-S02
0.25 Watt unregulated
single output
4 Pin SIP4 / 8 Pin DIP8 package
1000 VDC isolation up to 3000 VDC isolation
■ Low ripple and noise
■ Efficiency up to 72%
■ -40°C~85°C operation temperature range
■ Non-conductive black plastic case
■
■
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation (Per 1% Vin Charge)
Load regulation (From 20% to 100% Load)
(Output 3.3 V Model)
Ripple & Noise (20 MHz bandwith) (1)
Temperature coefficient
Capacitor load (2)
ABSOLUTE MAXIMUM RATINGS (4)
± 3%
± 1.2%
± 10%
± 20%
100 mV pk-pk
± 0.02%/°C
See table
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
5 modes
0 ~ 7 VDC
12 modes
0 ~ 15 VDC
24 modes
0 ~ 28 VDC
48 modes (SIP) 0 ~ 54 VDC
Lead soldering temperature
260°C
INPUT SPECIFICATIONS
(1.5 mm from case 10 sec.)
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current (3)
± 10%
See table
See table
Capacitors
20 mA pk-pk
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed to
be correct at time of publication. However, we accept no responsibility for
consequences arising from printing errors or inaccuracies.
Subject to change without notice.
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table
I/O isolation voltage (3 sec.)
Input / output
1000 ~ 3000 VDC
I/O isolation capacitance
60 pF typ.
I/O isolation resistance
1000 M Ohm
Switching frequency
variable 80 kHz
Humidity
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
> 1.121 Mhrs.
Safety standard (designed to meet)
IEC 60950-1
1) Ripple / Noise measured with 20 MHz bandwith.
2) Tested by minimal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
PHYSICAL SPECIFICATIONS
Case material
Non-conductive black plastic
(UL94V-0 rated)
Pin material SIP case > 0.5 mm Alloy42 solder-coated
DIP case > Ø 0.5 mm brass solder-coated
Potting material
Epoxy (UL94V-0 rated)
Weight
SIP > 1.5 g, DIP > 1.8 g
Dimensions
SIP > 0.46“ x 0.24“ x 0.4“
DIP > 0.50“ x 0.40“ x 0.27“
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: [email protected]
or use the forms on www.rsg-electronic.de („Kontakt“).
ENVIRONMENT SPECIFICATIONS
Operating temperature
Maximum case temperature
Storage temperature
Cooling
-40°C~ 85°C
(See derating curve)
100°C
-40°C~125°C
Nature convection
Page: 1/3
Last update: 03.09.12
RS1/RD1-S02
MODEL SELECTION GUIDE
Model Number
Input
Range VDC
Input current (mA)
No Load / Full Load
Output
VDC
Output current
Full Load (mA)
Efficiency
@FL (%)
Capacitor
Load (HF)
RS1-0503S02AX
RS1-0505S02AX
RS1-0507S02AX
RS1-0509S02AX
RS1-0512S02AX
RS1-0515S02AX
RS1-0518S02AX
RS1-0524S02AX
RS1-1203S02AX
RS1-1205S02AX
RS1-1207S02AX
RS1-1209S02AX
RS1-1212S02AX
RS1-1215S02AX
RS1-1218S02AX
RS1-1224S02AX
RS1-2403S02AX
RS1-2405S02AX
RS1-2407S02AX
RS1-2409S02AX
RS1-2412S02AX
RS1-2415S02AX
RS1-2418S02AX
RS1-2424S02AX
RS1-4803S02AX
RS1-4805S02AX
RS1-4807S02AX
RS1-4809S02AX
RS1-4812S02AX
RS1-4815S02AX
RS1-4818S02AX
RS1-4824S02AX
RD1-0503S02AX
RD1-0505S02AX
RD1-0507S02AX
RD1-0509S02AX
RD1-0512S02AX
RD1-0515S02AX
RD1-0518S02AX
RD1-0524S02AX
RD1-1203S02AX
RD1-1205S02AX
RD1-1207S02AX
RD1-1209S02AX
RD1-1212S02AX
RD1-1215S02AX
RD1-1218S02AX
RD1-1224S02AX
RD1-2403S02AX
RD1-2405S02AX
RD1-2407S02AX
RD1-2409S02AX
RD1-2412S02AX
RD1-2415S02AX
RD1-2418S02AX
RD1-2424S02AX
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
48
48
48
48
48
48
48
48
5
5
5
5
5
5
5
5
12
12
12
12
12
12
12
12
24
24
24
24
24
24
24
24
20 / 75
20 / 75
20 / 75
20 / 73
20 / 73
20 / 73
20 / 73
20 / 71
15 / 31
15 / 31
15 / 30
15 / 30
15 / 30
15 / 30
15 / 29
15 / 28
8 / 15
8 / 15
8 / 15
8 / 15
8 / 15
8 / 15
8 / 15
8 / 15
5 / 8.1
5 / 7.8
5 / 7.8
5 / 7.8
5 / 7.7
5 / 7.7
5 / 7.7
5 / 7.5
20 / 75
20 / 75
20 / 75
20 / 73
20 / 73
20 / 73
20 / 73
20 / 71
15 / 31
15 / 31
15 / 30
15 / 30
15 / 30
15 / 30
15 / 29
15 / 28
8 / 15
8 / 15
8 / 15
8 / 15
8 / 15
8 / 15
8 / 15
8 / 15
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
3.3
5
7.2
9
12
15
18
24
75.7
50
34.72
27.77
20.83
16.67
13.88
10.41
75.7
50
34.72
27.77
20.83
16.67
13.88
10.41
75.7
50
34.72
27.77
20.83
16.67
13.88
10.41
75.7
50
34.72
27.77
20.83
16.67
13.88
10.41
75.7
50
34.72
27.77
20.83
16.67
13.88
10.41
75.7
50
34.72
27.77
20.83
16.67
13.88
10.41
75.7
50
34.72
27.77
20.83
16.67
13.88
10.41
66
66
66
68
68
68
68
70
66
67
68
68
68
69
70
72
67
67
67
69
69
69
69
69
64
66
66
66
67
67
67
69
66
66
66
68
68
68
68
70
66
67
68
68
68
69
70
72
67
67
67
69
69
69
69
69
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
RS1/RD1-S02
0.25 Watt unregulated
single output
NUMBER STRUCTURE
RD1 - XX
XX
Name/Package
RS1=SIL4
RD1=DIL8
Input
05=5V
12=12V
24=24V
48=48V
Output
03=3.3V
05=5V
07=7.2V
09=9V
12=12V
15=15V
18=18V
24=24V
DERATING CURVE
D
10
A
X
Power
Code
02=0.25W internal
Type
S=Single
Isolation
1=1.0 kVDC
3=3.0 kVDC
LOADING VS OUTPUT VOLTAGE
LOADING VS OUTPUT VOLTAGE
Output Voltage
12 MODELS
Output Voltage
5 MODELS
Load
Load
PIN CONNECTIONS
MECHANICAL SPECIFICATIONS 4 Pin SIL
The thickness of 48V
input voltage model is
7.50 (0.29)
MECHANICAL SPECIFICATIONS 8 Pin DIL
Pin Number
Single 4 Pin SIL
Single 8 Pin DIL
1
2
3
4
5
7
-V Input
+V Input
-V Output
+V Output
-V Input
+V Input
+V Output
-V Output
Notes:
All dimensions are typical in millimeters (inches).
1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002)
2) Pin pitch tolerance: ± 0.35 (± 0.014)
3) Case tolerance: ± 0.5 (± 0.02)
Pin size is 0.5 mm
(0.02“) DIA or
0.50x0.30 mm
(0.02x0.01“)
Page: 3/3
Last update: 03.09.12
RSG Electronic Components GmbH
Sprendlinger Landstr. 115
D-63069 Offenbach
Tel. +49 69 984047-0
Fax +49 69 984047-77
mail: [email protected]
www.rsg-electronic.de