RS4/RD4-R10 1.0 Watt regulated single output 7 Pin SIP7 / 14 Pin DIP14 package 1000 VDC isolation up to 3000 VDC isolation ■ Low ripple and noise ■ Efficiency up to 68% ■ -40°C~85°C operation temperature range ■ Non-conductive black plastic case ■ ■ SIL 7 package, pic. similar OUTPUT SPECIFICATIONS Voltage accuracy Line regulation Load regulation (From 0% to 100% Load) (Output 3.3 V Model) Ripple & Noise (20 MHz bandwith) (1) Temperature coefficient Capacitor load (2) ABSOLUTE MAXIMUM RATINGS (4) ± 2% ± 0.5% ± 0.5% ± 1.0% 50 mV pk-pk ± 0.02%/°C See table These are stress ratings. Exposure of devices to any of these conditions may adversely affect long-term reliability. Input voltage (100 mS) 5 modes 0 ~ 7 VDC 12 modes 0 ~ 15 VDC 24 modes 0 ~ 28 VDC Lead soldering temperature 260°C (1.5 mm from case 10 sec.) INPUT SPECIFICATIONS Voltage range Max. input current No-load input current Input filter Input reflected ripple current (3) ± 10% See table See table Capacitors 20 mA pk-pk All specifications typical at Ta = 25°C, nominal input voltage and full load unless otherwise specified. The information and specifications contained in this data sheet are believed to be correct at time of publication. However, we accept no responsibility for consequences arising from printing errors or inaccuracies. Subject to change without notice. GENERAL SPECIFICATIONS NOTE Efficiency See table I/O isolation voltage (3 sec.) Input / output 1000 ~ 3000 VDC I/O isolation capacitance 60 pF typ. I/O isolation resistance 1000 M Ohm Switching frequency variable 50 kHz Humidity 95% rel. H Reliability calculated MTBF (MIL-HDBK-217F) > 4.261 Mhrs. Safety standard (designed to meet) IEC 60950-1 1) Ripple / Noise measured with 20 MHz bandwith. 2) Tested by minimal Vin and constant resistive load. 3) Measured input reflected ripple current with a simulated source inductance of 12uH. 4) Exceeding the absolute ratings of the unit could cause damage. It is not allowed for continuous operating. 5) Operation under no-load conditions will not damage these devices. However they may not meet all listed specifications. PHYSICAL SPECIFICATIONS Case material Pin material Potting material Weight Dimensions Non-conductive black plastic (UL94V-0 rated) 0.5 mm Alloy42 solder-coated Epoxy (UL94V-0 rated) 2.7 g SIP 0.76“ x 0.28“ x 0.39“ DIP 0.80“ x 0.40“ x 0.27“ The models listed are just for standard type. If you need a special specification product, please contact our service. Phone: +49 69 984047-0, mail to: [email protected] or use the forms on www.rsg-electronic.de („Kontakt“). ENVIRONMENT SPECIFICATIONS Operating temperature Maximum case temperature Storage temperature Cooling -40°C~ 85°C (See derating curve) 100°C -40°C~125°C Nature convection Page: 1/3 Last update: 30.01.09 RS4/RD4-R10 1.0 Watt regulated single output NUMBER STRUCTURE RS4 - XX Name/Package RS4=SIL7 RD4=DIL14 Input 05=5V 12=12V 24=24V XX Output 03=3.3V 05=5V 07=7.2V 09=9V 12=12V 15=15V DERATING CURVE R 10 Power 10=1.0W A X Code internal Type R=Single regulated Isolation 1=1.0 kVDC 3=3.0 kVDC MODEL SELECTION GUIDE Model Number Input Range VDC Input current (mA) No Load / Full Load Output VDC Output current Full Load (mA) Efficiency @FL (%) Capacitor Load (HF) RS4-0503R10AX RS4-0505R10AX RS4-0507R10AX RS4-0509R10AX RS4-0512R10AX RS4-0515R10AX RS4-1203R10AX RS4-1205R10AX RS4-1207R10AX RS4-1209R10AX RS4-1212R10AX RS4-1215R10AX RS4-2403R10AX RS4-2405R10AX RS4-2407R10AX RS4-2409R10AX RS4-2412R10AX RS4-2415R10AX RD4-0503R10AX RD4-0505R10AX RD4-0507R10AX RD4-0509R10AX RD4-0512R10AX RD4-0515R10AX RD4-1203R10AX RD4-1205R10AX RD4-1207R10AX RD4-1209R10AX RD4-1212R10AX RD4-1215R10AX RD4-2403R10AX RD4-2405R10AX RD4-2407R10AX RD4-2409R10AX RD4-2412R10AX RD4-2415R10AX 5 5 5 5 5 5 12 12 12 12 12 12 24 24 24 24 24 24 5 5 5 5 5 5 12 12 12 12 12 12 24 24 24 24 24 24 30 / 385 30 / 307 30 / 307 35 / 307 35 / 294 35 / 294 20 / 160 20 / 132 20 / 128 20 / 126 20 / 122 20 / 126 10 / 76 10 / 64 10 / 64 10 / 61 10 / 61 10 / 61 30 / 350 35 / 317 45 / 327 40 / 298 35 / 298 35 / 298 20 / 146 20 / 132 20 / 132 20 / 128 20 / 122 20 / 126 10 / 73 10 / 76 10 / 76 10 / 61 10 / 63 10 / 63 3.3 5 7.2 9 12 15 3.3 5 7.2 9 12 15 3.3 5 7.2 9 12 15 3.3 5 7.2 9 12 15 3.3 5 7.2 9 12 15 3.3 5 7.2 9 12 15 333 200 138.9 111.1 83.3 66.7 333 200 138.9 111.1 83.3 66.7 333 200 138.9 111.1 83.3 66.7 333 200 138.9 111.1 83.3 66.7 333 200 138.9 111.1 83.3 66.7 333 200 138.9 111.1 83.3 66.7 57 65 65 65 68 68 57 63 65 66 68 66 60 65 65 68 68 68 57 63 61 67 67 67 57 63 63 65 68 66 57 60 60 68 66 66 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 220 Page: 2/3 Last update: 30.01.09 RS4/RD4-R10 1.0 Watt regulated single output EFFICIENCY VS OUTPUT CURRENT 05 MODELS 12 MODELS 24 MODELS MECHANICAL SPECIFICATIONS 7 Pin SIL PIN CONNECTIONS 7 Pin SIL MECHANICAL SPECIFICATIONS 14 Pin DIL PIN CONNECTIONS 14 Pin DIL Notes: All dimensions are typical in millimeters (inches). 1) Pin diameter: 0.5 ± 0.05 (0.02 ± 0.002) 2) Pin pitch tolerance: ± 0.35 (± 0.014) 3) Case tolerance: ± 0.5 (± 0.02) Page: 3/3 Last update: 30.01.09 RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach Tel. +49 69 984047-0 Fax +49 69 984047-77 mail: [email protected] www.rsg-electronic.de